纤维素/甲壳素共混膜的结构表征与抗凝血性能

以 6wt %NaOH 4wt%尿素为纤维素的新溶剂 ,采用溶液共混法制备出纤维素 甲壳素共混膜 ,为甲壳素在碱性溶液中制膜提供了新的方法 .红外光谱、X 射线衍射、扫描电镜和力学性能、抗凝血性能测试结果表明 ,共混膜中甲壳素含量低于 4 0wt%时 ,纤维素与甲壳素分子间具有良好的相容性 ;在纤维素中引入适量甲壳素可提高共混膜的抗张强度 ,共混膜的干、湿态抗张强度在甲壳素含量 10wt%时最大 ,其值分别为 89 1MPa和 4 3 7MPa ,比纯态纤维素膜的干、湿态抗张强度分别提高了 6 7%和 11 5 % ;甲壳素的引入可明显降低血小板在共混膜表面的粘附、凝聚与变性 ,增大共混膜的抗凝血参数 ,甲壳素含量达到 5 0wt%时 ,该共混膜具有良好的抗凝血性能     

Utilizing Polymer Blends to Prepare Ultrathin Films with Diverse Cellulose Textures

This paper presents an overview of the recent work on ultrathin polymer blend films containing cellulose. Three systems prepared via trimethylsilyl cellulose derivative, which is subsequently hydrolyzed to cellulose, are presented: polystyrene/cellulose, poly(methyl methacrylate)/cellulose and polystyrene-block-polyethyleneoxide/cellulose. Diverse textures emerge within the films depending on the interactions between the polymers and their interactions with the substrate as well as on different solubilities of the polymers. Furthermore, an ultrathin film containing a cellulose/xylan blend is presented. This film was deposited directly from a common solvent (dimethylacetamide/lithium chloride) and it did not exhibit distinct morphological patterns comparable to the blends with synthetic polymers.     

Facile fabrication of chitosan active film with xylan via direct immersion

Chitosan film was immersed in NaOH solution with xylan to simply prepare active chitosan/xylan film. FT-IR, XRD, FE-SEM, AFM and XPS were used to evaluate the effects of xylan on the structure and morphology of chitosan film, and a wide variety of material characteristics of the chitosan/xylan composite films were investigated. The results showed that the xylan chains entered into the gap of chitosan film and became nodules, leading to strong hydrogen bonds and electrostatic interactions between chitosan and xylan. Moreover, the introduction of xylan not only resulted in stronger crystallinity and a more compact structure of chitosan film, but also had an important effect on the properties of chitosan film. The tensile strength, breaking elongation and anti-ultraviolet performance of the chitosan/xylan films were improved greatly with the increasing concentration of xylan; the water vapor transmission rate, water absorption rate and oxygen barrier property of chitosan/xylan composite films were higher than those of chitosan film; chitosan/xylan composite films still showed hydrophobicity when the xylan concentration was more than 1 %. The chitosan/xylan composite film has more potential to be used as food packaging than pure chitosan film.     

Revealing substituent effects on the concerted interaction of pnicogen, chalcogen, and halogen bonds in substituted s-triazine ring

Quantum chemical calculations have been performed to gauge the effect of substituents on concerted interactions of pnicogen, chalcogen, and halogen bonds in the X–TAZ···Y complexes (X = CN, F, Cl, Br, H, CH₃, OH, and NH₂, where TAZ and Y denote s-triazine ring and P, S, and Cl atoms, respectively) at the M06-2X/aug-cc-pVDZ level. The mutual interplay of these interactions is also investigated. The results indicate that diminutive effects are observed when the three kinds of noncovalent interactions pnicogen, chalcogen, and halogen bonds are coexisted in the complexes. These effects are studied in terms of energetic and geometric features of the complexes. In addition, Bader’s theory of “atoms in molecules” is used to analyze their strength of varying electron density at bond critical points. Natural bond orbital (NBO) theory is used to characterize the orbital interactions. The results indicate that the electron-withdrawing/donating substituents decrease/increase the magnitude of the binding energies compared to the unsubstituted X–TAZ···Y (X = H) complex. Good correlations among binding energies, Hammett constants, geometrical, atoms in molecular and NBO parameters are established in X–TAZ···Y complexes. By taking advantage of all the aforementioned computational methods, this study examines how these interactions mutually influence each other.     

Antifungal activity and humidity sensitivity of quaternized cellulose synthesized in NaOH/urea aqueous solution

In this work we report the fabrication of cellulose-based humidity responsive material with antifungal activity. The quaternized cellulose (QC) derivatives with low degree of substitution (DS) values of 0.08–0.37 were synthesized in NaOH/urea aqueous solution. Water insoluble QC membranes (c-QCM) were prepared by casting from QC aqueous solutions, followed by crosslinking with glutaraldehyde. The c-QCMs were disintegrated in acid solutions, but were able to keep membrane shape in neutral and mild basic solutions with pH value of 7.2 and 9.7. The equilibrium water adsorption ratios of c-QCMs were in the range of 66–98%, depending on the DS values of quaternary ammonium groups and the pH value of the aqueous solutions. The antifungal activity of QC was evaluated and found that QC could effectively inhibit the reproduction of Rhizopus stolonifer, Aspergillus flavus and Penicillium digitatum, with minimum inhibitory concentration of 5, 10, and 7.5 mg/mL, respectively. The resistivity of the c-QCM changed for about 65–134 times corresponding to the change of environmental relative humidity from 20 to 99%; and the performance of c-QCM as a resistive-type humidity responsive material was consistent in the cycling of relative humidity.     

Synthesis, structure and solution properties of the novel polyampholytes based on cellulose

A novel cellulose-based polyampholyte derivative, carboxylethyl quaternized cellulose (CEQC), was homogeneously synthesized by introducing positively charged quaternary ammonium groups and negatively charged carboxyl groups to the backbone of cellulose. The structure and dilute solution properties of CEQCs were characterized with elemental analysis, FTIR, NMR, viscometer, light scattering and zeta-potential measurement. The nitrogen content and total degree of substituent of acylamino and carboxyl groups increased with an increase of the molar ratio of acrylamide to the anhydroglucose unit of quaternized cellulose (QC). The salt-resistance of CEQC was improved remarkably by introducing opposite charged carboxyl to the QC chains. The intrinsic viscosity of the prepared polyampholytes was found to be very sensitive to the pH of the solutions. CEQC-1, the sample with relative low content of carboxyl groups, behaved as a classical cationic polyelectrolyte. However, CEQC-2 and CEQC-3, the samples with higher content of carboxyl groups, displayed typical polyampholyte behavior, and the isoelectric points (IEP) were determined to be 5.0 and 3.8 respectively. This work provided a facile method for the synthesis of novel cellulose-based polyampholytes with different IEP.     

Adsorption and viscoelastic properties of cationic xylan on cellulose film using QCM-D

The adsorption and viscoelastic properties of cationic xylan layers adsorbed from an aqueous electrolyte solution (NaCl 0, 1, 10, 100 mM) on a cellulose model surface were studied using quartz crystal microbalance with dissipation (QCM-D). Three cationic xylans with different charge densities were used (molecular weight, 9,600 g/mol with degrees of substitution, DS = 0.150, 0.191, and 0.259). The influences of the electrolyte concentration and charge density of cationic xylan on its adsorption onto a cellulose surface were investigated. Low charged cationic xylan was substantially more efficient in surface adsorption on cellulose compared to high charged cationic xylan at a low concentration of electrolytes. Adsorption of low charged cationic xylan decreased with increases in electrolyte concentration. However, adsorption of high cationic xylan increased with electrolyte concentration. The conformation and viscoelastic properties of the layers were interpreted by modeling the data under the assumption that the layers can be explained by the a Voigt model. Low charged cationic xylan adsorbed relatively weakly onto the cellulose surface, and formed a thicker, softer layer than high charged cationic xylan. On the other hand, high charged cationic xylan formed a thinner adsorption layer onto the cellulose surface.     

Synthesis and antifungal property of N-(aryl) and quaternary N-(aryl) chitosan derivatives against Botrytis cinerea

A series of N-(aryl) and their quaternary N-(aryl) chitosan derivatives were synthesized and evaluated for their antifungal activity against crop-threatening fungus Botrytis cinerea. Schiff bases were firstly synthesized by the reaction of chitosan with cinnamaldehyde, cuminaldehyde and 4-dimethylaminobenzaldehyde followed by reduction with sodium borohydride to form N-(aryl) chitosans. Quaternary N-(aryl) chitosans were then obtained by reaction of N-(aryl) chitosan compounds with ethyl iodide. The chemical structures were characterized by ¹H-NMR, FT-IR and UV spectroscopic techniques. The antifungal activity was evaluated in vitro against B. cinerea by mycelial growth inhibition method and in vivo by application of compounds to tomato plants prior to inoculation with fungal spores. In an in vitro experiment, all quaternized chitosans were more active than N-(aryl) chitosan derivatives and N,N,N-(diethylcinnamyl) chitosan (QC1) was the most potent (EC₅₀ = 1,147 mg/L) against mecelia however, N,N,N-(diethyl-p-dimethylaminobenzyl) chitosan (QC3) was the most potent (EC₅₀ = 334 mg/L) against spores. In an in vivo study, no disease incidence (0.0 %) was observed with QC1 and QC3 at 1,000 mg/L. Spray liquid chitosan enhanced total phenolics and guaiacol peroxidase in inoculated leaves.     

Chitin/graphene oxide composite films with enhanced mechanical properties prepared in NaOH/urea aqueous solution

Chitin/graphene oxide (GO) composite films with excellent mechanical properties were prepared in NaOH/urea solution using a freezing/thawing method. The structure, thermal stability and mechanical properties of the composite films were investigated. Use of an atomic force microscope and transmission electron microscopy indicated that GO was successfully exfoliated to a single layer by ultrasonication. The results revealed that GO nanosheets were homogeneously dispersed and embedded in the chitin matrix. Due to the strong interactions between GO and the chitin matrix, the tensile strength and elongation at break of the composite film possessing 1.64 wt% GO were significantly improved by 98.7 and 114.5 %, respectively, compared with pure chitin film.     

Density functional study on rare gas-noble metal closed-shell interaction in XeMX (M = Au, Ag, Cu; X = F, Cl, Br) systems

The rare gas-noble metal systems XeMX (M = Au, Ag, Cu; X = F, Cl, Br) were investigated at the CCSD(T) and DFT levels. Geometric structures, natural bond orbital population, HOMO-LUMO gap, the rare gas-noble metal interaction and the chemical deformation density were analyzed. Experimental structure parameters of the XeAuF and XeMX (M = Ag, Cu; X = F, Cl) were reproduced at Xα level. At the same time, the XeAuCl and XeMBr (M = Au, Ag, Cu) compounds were predicted. The electronegativity of halogen atom X correlates with the M–X bond length, HOMO-LUMO gap, electronic structures and Xe–M bond energy.     

Comparison of the influence of titanium and chromium adhesion layers on the properties of sol–gel derived NKN thin films

Lead-free (Na_0.5K_0.5)NbO₃ (NKN) thin films were prepared on Pt/X/SiO₂/Si substrates (with the adhesion promoters X = Ti, Cr) by a sol–gel process with and without post-annealing treatment. The effect of the diffusion of the adhesion layer elements Ti and Cr into the NKN film was analysed by secondary ion mass spectrometry, scanning electron microscopy pictures, X-ray diffraction (XRD), and leakage current measurements. It turned out that Cr diffuses into the films to a higher extent than Ti. The high amount of Cr diffusion led to the formation of a secondary phase, as seen in the XRD pattern, and to pore formation on the surface of the NKN films. In contrast, the films with Ti adhesion layer were single phase NKN without pore formation. Also, the leakage current measurements showed a strong influence of the Cr diffusion. The leakage current of the films with Cr adhesion layer was about four orders of magnitude higher than that of the films with Ti adhesion layer. The study shows the strong influence of the adhesion layer of the substrate on the properties of NKN films.     

Organomonophosphines in PtP<Subscript>2</Subscript>XY derivatives: structural aspects

This review covers over two hundred Pt(II) complexes with a PtP₂XY inner coordination sphere, in which the P-donor ligands are organomonophosphines. These complexes can be divided into six groups: PtP₂HX (X = O, N, B, Cl, S, Br, Se, Si, or I); PtP₂OX (X = N, Cl, S, or Se); PtP₂NX (X = CN, Cl, B, S, Br, Se, or Te); PtP₂BX (X = F, Cl, S, Br, or I); PtP₂ClX (X = S, Se, Si, As, or Te); and PtP₂SiX (X = Br or Te). The complexes crystallize in several crystal systems: hexagonal (×1), tetragonal (×1), orthorhombic (×22), triclinic (×78), and monoclinic (×130). There are complexes with cis-configuration and trans-configuration, the latter by far prevails. Besides monodentate ligands, there are also heterobidentate ligands with: O/N, O/S, O/Se, N/S, N/Se, and N/Te, donor sites. These chelating ligands form a wide variety of metallocyclic, four-, five-, and six-membered rings, and the effects of both steric and electronic factors can be seen from the values of the L–Pt–L bite angles. The structural parameters are analyzed and discussed with particular attention to trans-influences.     

Influence of urea and glycerol on functional properties of biodegradable PVA/xylan composite films

In recent years, numerous studies have focused on biodegradable plastics for agricultural applications. To improve the mechanical and hydrophobic properties, biodegradable xylan composite films containing poly(vinyl alcohol) (PVA) were successfully prepared by casting method in this work. A series of composite films at a PVA/xylan weight ratio of 3:1 under the addition of glycerol and urea were investigated. Influences of the urea and glycerol amounts on the functional properties of composite films such as hydrophilicity/hydrophobicity, water vapor permeability (WVP), mechanical properties, solubility and degradability were comparatively investigated. Results showed that increasing the glycerol amount led to a decrease in tensile strength and an increase in elongation at break and WVP, while the addition of 1 % urea in composite films without glycerol had a positive impact on improving the water resistance of composite films; the contact angle and WVP values reached 114.68° and 4.11 × 10^?11 g m^?1 s^?1 Pa^?1. Moreover, thermogravimetric analysis, FTIR and a scanning electron microscope were used to confirm the compatibility of the PVA and xylan components. FTIR analysis displayed the intensity of hydroxyl groups of films became stronger with increasing amounts of glycerol, while the opposite results were obtained with an increase of the amount of urea. These indicated that glycerol could improve the miscibility between PVA and xylan, and the addition of urea could enhance the water resistance of composite films.     

Photochemical property of the polymer-bearing pendant norbornadiene moiety and storage stability of the resulting quadricyclane group in the polymer

A polymer bearing pendant norbornadiene (NBD) moieties and a low molecular weight model compound ([2-carbobenzyloxy-3-phenyl-2,5-norbornadiene CBPNB)], were synthesized by substitution reaction of poly(p-chloromethylstyrene) and benzyl chloride, respectively, with the potassium salt of 3-phenyl-2,5-norbornadiene-2-carboxylic acid. Photochemical valence isomerization and storage stabilities of the resulting polymer having corresponding pendant quadricyclane (QC) groups and the low molecular weight QC compound were investigated in dichloromethane solution. It was found that the rate of photochemical valence isomerization of the pendant NBD moiety in the polymer was the same as or slightly higher than that of CBPNB, and the storage stability of the QC group in the polymer was higher than that of the QC compound resulting from CBPNB in the solution. The photochemical reaction of the pendant NBD moiety within the polymer without catalyst proceeded quantitatively in the film state. However, the photochemical reaction of the polymer films blended with 5,10,15,20-tetraphenyl-21H,23H-porphine cobalt (II) catalyst (Co-TPP) did not proceed quantitatively, and the degree of conversion of the pendant NBD moiety in the polymer decreased with increasing amounts of Co-TPP in the film. The QC group produced in the polymer by photo-irradiation had excellent storage stability in the film state without Co-TPP. On the other hand, the QC group in the polymer films blended with Co-TPP Catalyst reverted gradually to the NBD group at room temperature.     

Conformational preferences of fluorocyclohexane and 1-fluoro-1-silacyclohexane molecules: ab initio study and NBO analysis

The molecular structure of the axial and equatorial conformers of fluorocyclohexane and 1-fluoro-1-silacyclohexane, H₂C(CH₂CH₂)₂XH–F (X = C or Si), as well as the thermodynamic equilibrium between these species were investigated by means of quantum chemical calculations up to MP2/aug-cc-pVTZ level of theory. According to MP2 data, these compounds consist of a mixture of conformers with chair conformation and C _s symmetry differing in the axial and equatorial position of the C–F/Si–F bonds (axial = 42/56 mol%, equatorial = 58/44 mol%) at T = 298 K. This corresponds to a free energy difference of A = (G _ax ? G _eq) = 0.19/?0.13 kcal mol^?1 for X = C/Si. NBO analysis revealed that the axial conformer of 1-fluoro-1-silacyclohexane is an example of stabilization of the form that is unfavorable in terms of conjugation effects; stabilization is achieved mainly due to steric interactions. The equatorial conformer of fluorocyclohexane is an example of stabilization of the form that is unfavorable in terms of electrostatic interactions; stabilization is achieved due to steric and conjugation effects.     

Characterization of <Emphasis Type="Italic">σ</Emphasis>-hole interactions in 1:1 and 1:2 complexes of YOF<Subscript>2</Subscript>X (X = F,Cl, Br,I; Y = P,As) with ammonia: competition between halogen and pnicogen bonds

Ab initio calculations at the MP2/aug-cc-pVTZ level of theory are performed to examine 1:1 and 1:2 complexes of YOF₂X (X = F, Cl, Br, I; Y = P, As) with ammonia. The YOF₂X:NH₃ complexes are formed through the interaction of the lone pair of the ammonia with the σ-hole region associated with the X or Y atom of YOF₂X molecule. The calculated interaction energies of halogen-bonded complexes are between ?1.06 kcal/mol in the POF₃···NH₃ and ?6.21 kcal/mol in the AsOF₂I···NH₃ one. For a given Y atom, the largest pnicogen bond interaction energy is found for the YOF₃, while the smallest for the YOF₂I one. Almost a strong linear relationship is evident between the interaction energies and the magnitudes of the positive electrostatic potentials on the X and Y atoms. The results indicate that the interaction energies of halogen and pnicogen bonds in the ternary H₃N:YOF₂X:NH₃ systems are less negative relative to the respective binary systems. The interaction energy of Y···N bond is decreased by 1–22 %, whereas that of X···N bond by about 5–61 %. That is, both Y···N and X···N interactions exhibit anticooperativity or diminutive effects in the ternary complexes.     

Cp/mas 13c nmr and Electron Diffraction Study of Bacterial Cellulose Structure Affected by Cell Wall Polysaccharides

Acetobacter xylinum was cultured in Schramm–Hestrin medium containing pectin (pectin medium), xylan (xylan medium), or glucomannan (mannan medium). X-ray diffractometry revealed that xylan and glucomannan affected the size of the cellulose crystals and their d-spacing values. Solid-state cross polarization magic angle spinning carbon-13 nuclear magnetic resonance spectroscopy indicated that the ratio of cellulose I was reduced by the addition of polysaccharides. These effects were more remarkable on the cellulose in the mannan medium than that in the xylan medium, and were scarcely observed in the pectin medium. Electron diffraction analysis revealed that these effects on hemicelluloses along cellulose microfibrils are continuous in the mannan medium and discontinuous in the xylan medium. These findings suggest that the uronic acid in the polysaccharides prevents interactions with cellulose leading to alterations of the structure of the cellulose crystal.     

Determination of global DNA methylation level by capillary electrophoresis using octyl-modified quaternized cellulose as an electrolyte additive

A new cellulose derivative, octyl-modified quaternized cellulose (OMQC), was synthesized and used as electrolyte additive for the analysis of 5-methylcytosine by capillary electrophoresis with UV detection. While added in the background electrolyte, OMQC carrying octyl groups and quaternary ammonium groups exhibited dynamic coating ability. Capillary coated with OMQC was able to generate a stable anodal electro-osmotic flow even at pH 12.0. After several running conditions were optimized, a new method for quantification of genomic methylation level was developed on the basis of hydrolysis of DNA by formic acid and separation of nucleic acid bases by capillary electrophoresis. Cytosine and 5-methylcytosine were separated with a resolution near 4.0 in less than 10 min. The detection limits (S/N?=?3) were 1.1 and 1.5 μg/mL for cytosine and 5-methylcytosine, respectively.     

The Enhancement of the Formation of Wells–Dawson-Type Polyoxometalates by the Addition of High Concentrations of LiCl

Wells–Dawson-type polyoxometalates are formed by heating an acidic Mo(VI) or W(VI) solution containing significantly higher concentrations of hetero ions, P(V) or As(V), than the ideal molar ratio [M]/[X] = 1/9 (M = Mo, W; X = P, As). Most of the phosphate and arsenate remains unreacted in the reaction mixture. These reaction conditions are unusual, even though more reagents than the stoichiometric amounts are frequently needed to obtain complete reactions. In the present study, the replacement of a large amount of unreacted hetero ions containing salts by normal ions (salts) was investigated. The formation of Wells–Dawson-type polyoxometalates, [X₂M₁₈O₆₂]^6? (X = P, As; M = Mo, W), in the presence of LiCl and NaCl was investigated by Raman spectroscopy and ³¹P NMR in aqueous solution. The addition of LiCl enhanced the formation of Wells–Dawson-type polyoxometalates, which formed under solution conditions close to the ideal molar ratio [M]/[X] = 1/9.     

Properties of poly(acrylamide)/TEMPO-oxidized cellulose nanofibril composite films

Self-standing composite films consisting of 2,2,6,6-tetramethylpiperidine-1-oxyl-oxidized cellulose nanofibril (TOCN) and anionic poly(acrylamide) (PAM) in various weight ratios were prepared by casting and drying of homogeneous mixtures of aqueous TOCN dispersion and PAM solution. PAM/TOCN composite films consisting of 25 % PAM and 75 % TOCN had clearly higher Young’s modulus (13.9 GPa) and tensile strength (266 MPa) than 100 % TOCN film (10.8 GPa and 223 MPa, respectively) or 100 % PAM film (4.9 GPa and 78 MPa, respectively), showing that PAM molecules have mechanical reinforcement ability in TOCN matrix. Some attractive interactions are likely formed between TOCN element surfaces and PAM molecules. In contrast, no such mechanical improvements were observed for poly(vinyl alcohol)/TOCN or oxidized starch/TOCN composite films prepared as references. Moreover, the mechanical properties of the PAM/TOCN composite films were further improved by controlling molecular mass and branching degree of the PAM. The high optical transparency and low coefficient of thermal expansion of the 100 % TOCN film were mostly maintained in the TOCN composite film containing 25 % PAM.