Hierarchical nanocomposites of polyaniline scales coated on graphene oxide sheets for enhanced supercapacitors

The homogeneous polyaniline–graphene oxide (PANI-GO) nanocomposites were facilely assembled with a redox system in which cumene hydroperoxide (CHP) and iron dichloride (FeCl₂) acted as oxidant and reductant, respectively. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) images showed that PANI scales coated uniformly on the surface of GO sheets owing to the synergistic effect between the PANI and GO. The obtained PANI-GO nanocomposites exhibited improved electrochemical performance as an electrode material for supercapacitors compared with the pure PANI. The specific capacitance of the PANI-GO nanocomposites was high up to 308.3 F g^?1, much higher than that of the pure PANI with specific capacitance of 150 F g^?1 at a current density of 1 A g^?1 in 2 M H₂SO₄ electrolyte. The Raman and XPS results illustrated that enhanced electrochemical performance might be attributed to the π-π conjugation between the PANI and GO sheets.     

The preparation of LaSr<Subscript>3</Subscript>Fe<Subscript>3</Subscript>O<Subscript>10 − <Emphasis Type="Italic">δ</Emphasis></Subscript> and its electrochemical performance

LaSr₃Fe₃O_10 ? δ powders were synthesized by hydrothermal method and characterized by XRD and SEM. The XRD patterns showed that the sample calcined at 1000 °C was single phase and the sample calcined at 900 °C had tiny amount of LaSrFeO₄ phase. The single-phase LaSr₃Fe₃O_10 ? δ powders were used to prepare test electrode. The capacitive behaviors of LaSr₃Fe₃O_10 ? δ electrode were analyzed by cyclic voltammetry, galvanostatic charge-discharge techniques, and electrochemical impedance spectroscopy. The electrochemical results showed a capacity as high as 470 F g^?1 at a scan rate of 1 mV s^?1 and 380 F g^?1 at a charge-discharge current density of 0.1 A g^?1 in 6 M KOH solution. The electrode showed good cyclic stability since its capacitive retention is 87.1% after 1000 charge-discharge cycles. The electrochemical performances suggest that LaSr₃Fe₃O_10 ? δ could be a potential candidate as a capacitive electrode material.     

Resorcinol-formaldehyde carbon spheres/polyaniline composite with excellent electrochemical performance for supercapacitors

Well-dispersed resorcinol-formaldehyde-based carbon spheres (RFCs) have been prepared by the polycondensation of resorcinol and formaldehyde with ammonia as catalyst and subsequent carbonization of the obtained polymer. In situ polymerization of the aniline occurred in the suspension of the RFC, and RFC was surrounded by the polyaniline (PANI) wires. The PANI and RFC hybrid network (PRFC) formed gradually. In a three-electrode mode, the specific capacitance (C _sp) of PRFC reaches 315 F g^?1 at a current density of 1 A g^?1 in 2 M H₂SO₄, much higher than that of pure PANI (225 F g^?1) and RFC (121.7 F g^?1). Furthermore, the C _sp of PRFC retains 80.0 % after 1000 charge-discharge processes at a current density of 5 Ag^?1. The enhanced electrochemical performance of the PRFC came from its homogeneous three-dimensional hierarchical network structure, good electric conductivity of the PANI around the RFC, and the synergistic effect between the RFC and PANI.     

In situ synthesis of crosslinked-polyaniline nano-pillar arrays/reduced graphene oxide nanocomposites for supercapacitors

Crosslinked-polyaniline (CPA) nano-pillar arrays adsorbed on the surface of reduced graphene oxide (RGO) sheets were synthesized by in situ solution polymerization through two steps of reduction. The electrochemical analyses demonstrated that the befittingly reduced CPA/RGO composite exhibited high performance as electrode materials for supercapacitors. The CPA/RGO composite showed very high specific capacitance of 1532 F g^?1 at a scan rate of 10 mV s^?1 or 694 F g^?1 at a current density of 2 A g^?1 in 1 M H₂SO₄ electrolyte, as well as great energy density of 61.4 W h kg^?1 at a current density of 2 A g^?1. The electrode material also had decent power density of 4 kW kg^?1 at a current density of 10 A g^?1, and good cycling stability of 92.5 % capacitance retained after 500 cycles of cyclic voltammetry at 500 mV s^?1. The neat microstructures and super electrochemical properties suggest the potential use of the composites in supercapacitors.     

Fabrication of novel solid-state supercapacitor using a Nafion polymer membrane with graphene oxide/multiwalled carbon nanotube/polyaniline

In the current work, the effect of aniline concentration on the polymerization process and supercapacitive behavior of graphene oxide/multiwalled carbon nanotubes/polyaniline (GMP) nanocomposites were studied. Based on the obtained results, GMP nanocomposite with 0.5 M aniline (GMP5) was selected as the optimum concentration in terms of high current density and high specific capacitance. Nafion-based ionic polymer-free metal composite (IPFMC) supercapacitor was fabricated for the GMP5 nanocomposite. Solid-state symmetric supercapacitor was made after spraying of GMP5 in. on both sides of Nafion membrane. The electrochemical properties were investigated by cyclic voltammetry (CV), galvanostatic charge–discharge (CD), and electrochemical impedance spectroscopy (EIS) techniques in 0.5 M Na₂SO₄.The specific capacitance of 383.25 F g^?1 (326 mF cm^?2) and 527.5 F g^?1 (42 mF cm^?2) was obtained for the GMP5 in solid-state supercapacitor and three-electrode cell at a scan rate of 10 mV s^?1, respectively. The maximum energy and power densities of 53.64 and 1777.4 W kg^?1 were obtained for the IPFMC-based supercapacitor.

Open image in new window

Graphical abstract Schematic of the solid-state supercapacitor based on the GMP5 nanocomposite

     

Electrochemical exfoliation and in situ carboxylic functionalization of graphite in non-fluoro ionic liquid for supercapacitor application

Simultaneous electrochemical generation and functionalization of nano-sized graphite from graphite had been carried out in a non-fluoroanion-based ionic liquid, namely, triethylmethylammonium methylsulfate (TEMAMS) containing water and acetonitrile (AN) in different weight ratios. The oxygen-based functional groups attached with the exfoliated material had been identified using Fourier transform infrared spectroscopy (FTIR), and morphological changes were characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). A symmetrical supercapacitor was fabricated using the exfoliated nano-sized graphite, and the influence of surface functionalities on its performance was investigated using electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), and galvanostatic charge–discharge cycles (CC). The highest specific capacitance (C _sp) value of 140 F g^?1 at 0.25 A g^?1 was obtained in 1.0 M H₂SO₄, followed by aqueous TEMAMS (125 F g^?1), TEMAMS/acetonitrile (115 F g^?1), and TEMAMS (106 F g^?1) at 0.10 A g^?1.     

Mechanochemically prepared polyaniline and graphene-based nanocomposites as electrodes of supercapacitors

Conductive nanocomposites based on polyaniline and graphene (PAni/Gr) were prepared by cheap and efficient mechanochemical method. The uniform distribution of Gr nanoparticles in the polymer matrix and the ordering of the polymer chains due to the action of mechanical shear stresses, which were established by TEM, stipulated high specific capacitance about 920 F g^?1 in ??0.2–1.0 V vs. Ag/AgCl potential range. PAni/Gr-based electrodes are able to provide the specific capacitance of ~?750 F g^?1 at 2 A g^?1 in symmetric supercapacitors (SSC) and stably cycle at the operating voltage V?=?0.65 V for 10,000 charge-discharge cycles with 96% capacitance retention, whereas the increasing of V leads to the loss of stability as a result of the cathode degradation. PAni/Gr-based SSC possessed improved self-discharge showed high rate capability, and the specific power of such SSC could reach ~?10 kW kg^?1 at the specific energy of ~?18 W h kg^?1.     

Pomegranate rind-derived activated carbon as electrode material for high-performance supercapacitors

In this paper, activated carbon materials were synthesized from pomegranate rind through carbonization and alkaline activation processes. The effects of pyrolytic temperature on the textual properties and electrochemical performance were investigated. The surface area of the activated carbon can reach at least 2200 m² g^?1 at different pyrolytic temperatures. It was found that, at the range of 600–900 °C, decreasing the carbonization temperature leads to the increase of t-plot micropore area, t-plot micropore volume, and capacitance. Further decreasing the carbonization temperature to 500 °C also leads to the increase of t-plot micropore area and t-plot micropore volume, but the capacitance is slightly poorer. The activated carbon carbonized at 600 °C and activated at 800 °C possesses very high specific area (2931 m² g^?1) and exhibits very high capacitance (～268 F g^?1 at 0.1 A g^?1 and ～242 F g^?1 at 1 A g^?1). There is no capacitance fading after 2000th cycle.     

Fabrication and characterisation of a mixed oxide-covered mesh electrode composed of NiCo<Subscript>2</Subscript>O<Subscript>4</Subscript> and its capability of generating hydroxyl radicals during the oxygen evolution reaction in electrolyte-free water

A mixed oxide-covered mesh electrode composed of NiCo₂O₄ (MOME-NiCo₂O₄) was prepared on a stainless-steel substrate using thermal decomposition (slow-cooling rate method). Surface, bulk and electrochemical properties of MOME were studied using different techniques, namely scanning electron microscopy (SEM), X-ray diffraction (XRD), cyclic voltammetry (CV) with determination of the electrochemical porosity (?) and morphology factor (φ) parameters, quasi-stationary polarisation curves (PC) and electrochemical impedance spectroscopy (EIS). SEM images revealed a good coverage of the metallic wires by a compact oxide layer (absence of cracks). XRD analysis confirmed the formation of the spinel NiCo₂O₄ with the presence of NiO. The ‘in situ’ surface parameters denoted as ? and φ exhibited values of 0.39 and 0.33, respectively, revealing that the electrochemically active surface area is mainly confined to the ‘outer/external’ surface regions of the oxide layer. The PC was characterised by two Tafel slopes distributed in the low (b ₁ = 46 mV dec^?1) and high (b ₂ = 59 mV dec^?1) overpotential domains. The corresponding apparent exchange current densities were j ₀₍₁₎ = (3.43 ± 0.11) × 10^?6 A cm^?2 and j ₀₍₂₎ = (6.70 ± 0.08) × 10^?6 A cm^?2, respectively. The EIS study accomplished in the low-overpotential domain revealed a Tafel slope (b ₁) of 51 mV dec^?1. According to the spin-trapping reaction using N,N-dimethyl-p-nitrosoaniline (RNO), the MOME-NiCo₂O₄ electrode exhibited good performance for the generation of weakly adsorbed hydroxyl radicals (HO^?) during the OER in electrolyte-free water.     

Facile synthesis of CuO nanosheets as electrode for supercapacitor with long cyclic stability in novel methyl imidazole-based ionic liquid electrolyte

Hierarchical CuO nanosheets were synthesized through a facile, eco-friendly reflux deposition approach for supercapacitor electrode material for energy storage. The resultant CuO nanosheets were characterized by Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and nitrogen adsorption-desorption isotherm techniques. The supercapacitor behavior of CuO nanosheets was investigated by cyclic voltammetry, galvanostatic charge/discharge, and electrochemical impedance spectroscopy in novel 0.1 M aqueous 1-(1′-methyl-2′-oxo-propyl)-3-dimethylimidazolium chloride [MOPMIM][Cl] ionic liquid as an electrolyte. The result demonstrate that CuO nanosheets exhibit specific capacitance of 180 F g^?1 at 10 mV s^?1 scan rate which is the highest value in ionic liquid electrolyte and 87% specific capacitance retention after 5000th cycle. The electrochemical performance proves CuO nanosheets as electrode with ionic liquid electrolyte for developing green chemistry approach in supercapacitor.

Open image in new window

Graphical abstract As-synthesized, CuO nanosheets demonstrate excellent supercapacitor electrode performance with high specific capacitance of 180 F g^?1 at 10 mV s^?1 scan rate and 87% specific capacitance retention in 0.1 M aqueous [MOPMIM][Cl] IL electrolyte

     

One-step preparation of sulfonated carbon and subsequent preparation of hybrid material with polyaniline salt: a promising supercapacitor electrode material

The present trend to increase the energy density of electrochemical supercapacitor is to hybrid the electrochemical double layer capacitance electrode materials of carbon with loading or encapsulation of transition metal oxide or conductive polymeric pseudocapacitor materials as the binary or ternary hybrid electrochemical active materials. In this work, we selected polyaniline salt-sulfonated carbon hybrid (PANI-SA?C _SA ) as a cheaper electrode material for supercapacitor electrode. Sulfonated carbon (C _SA ) was prepared from hydrothermal carbonization of furaldehyde and p-toluenesulfonic acid. Polyaniline-sulfate salt containing sulfonated carbon was prepared by chemical oxidative polymerization of aniline using ammonium persulfate in presence of sulfuric acid and sulfonated carbon via aqueous, emulsion and interfacial polymerization pathways. Formation of hybrid material was confirmed from scanning electron microscopy. Among the hybrid prepared with three different polymerization pathways, hybrid prepared by aqueous polymerization pathway showed better electrochemical performance. The specific capacitance of the hybrid prepared via aqueous polymerization was 600 F g^?1, which is higher than that of the pristine PANI-SA (350 F g^?1) and C _SA (30 F g^?1). Hybrid material was subjected for 8000 charge-discharge cycles and at 8000 cycles; it showed 88% retention of its original specific capacitance value of 485 F g^?1 with coulombic efficiency (97–100%). These results showed that C _SA micro spheres prevent the degradation of PANI-SA chains during charge/discharge cycles. Specific capacitance, cycle life, low solution resistance, low charge transfer resistance and high phase angle value of PANI-SA?C _SA supercapacitor cell indicates a higher performance supercapacitor system.

Open image in new window

Graphical abstract Synthesis of hybrid of sulfonated carbon with polyaniline sulfate salt and its supercapacitor performance Ravi Bolagam, Palaniappan Srinivasan,^* Rajender Boddula

     

Pyridine-containing metal-organic frameworks as precursor for nitrogen-doped porous carbons with high-performance capacitive behavior

A novel pyridine-containing metal-organic framework (MOF, [Zn(bpdc)DMA]·DMF, bpdc = 2,2′-bipyridine-5,5′-dicarboxylate) was directly carbonized at different temperature to produce nitrogen-doped porous carbons (NPCs). The as-prepared porous carbons, NPC800 (obtained at 800 °C) and NPC1000 (obtained at 1000 °C), were characterized by scanning electron microscopy, X-ray powder diffraction, N₂ sorption isotherms, and X-ray photoelectron spectroscopy (XPS). The results from elemental analysis and XPS confirmed that the pyridine groups in MOF served as nitrogen sources to produce NPCs, and NPC800 possessed the higher nitrogen content than NPC1000. N₂ sorption data demonstrated that NPC800 exhibited the larger specific surface area and pore volume than NPC1000. The capacitive properties of NPC800 and NPC1000 were investigated in KOH aqueous electrolyte by cyclic voltammetry and galvanostatic charge–discharge curves. NPC800 showed the higher specific capacitance (226.6 F g^?1 at 1 A g^?1) than NPC1000 and retained 178.0 F g^?1 even at a high current density up to 10 A g^?1. It was found that the donation of N species to capacitance was more than the role of porosity in view of their synergetic effect.     

Sensitive detection of sulfanilamide by redox process electroanalysis of oxidation products formed in situ on glassy carbon electrode

This paper reported a simple method for sulfanilamide determination by redox process electroanalysis of oxidation products (SFDox) formed in situ on glassy carbon electrode. The CV experiments showed a reversible process after applied E _acc = + 1.06 V and t _acc = 1 s, in 0.1 mol L^?1 BRBS (pH = 2.0) at 50 mV s^?1. Different voltammetric scan rates (from 10 to 450 mV s^?1) suggested that the redox peaks of SFDox on the glassy carbon electrode (GCE) is an adsorption-controlled process. Square-wave voltammetry (SWV) method optimized conditions showed a linear response to SFD from 3.00 to 250.0 μmol L^?1 (R = 0.998) with a limit of detection of 0.638 μmol L^?1 and limit of quantification of 2.0 μmol L^?1. The developed the SWV method was successfully used in the determination of SFD pharmaceutical formulation and human serum. The SFD quantification results in pharmaceutical obtained by SWV-GCE were comparable to those found by official analytical protocols.     

Facile preparation of nitrogen-doped porous carbon for high performance symmetric supercapacitor

In this work, the micromolecule l-glutamic acid (Glu) is employed as nitrogen-rich precursor to prepare a novel porous carbon, and ZnCl₂ is used as activating agent to improve the surface area and electrochemical performance of the carbon. The nitrogen content of the carbon (Glu-2.5) prepared by Glu and ZnCl₂ with a mass ratio of 1:2.5 retains as high as 7.1 % at an activation temperature of 700 °C. The surface area and pore volume of Glu-2.5 are 1007.4 m² g^?1 and 0.57 cm³ g^?1, respectively. Glu-2.5 exhibits a high specific capacitance of 330.6 F g^?1 in 2 M KOH electrolyte at the current density of 1 A g^?1and good cycling stability (89 % retention of capacitance after 5000 charge/discharge cycles). More importantly, the assembled symmetric supercapacitor using Glu-2.5 as electrodes reveals a high energy density (16.7 Wh kg^?1) under the power density of 404.7 W kg^?1. Owing to its inherent advantages, Glu-2.5 could be a promising and scalable alternative applied to energy storage/conversion.     

Synthesis of micro- and mesoporous carbon spheres for supercapacitor electrode

Micro- and mesoporous carbon spheres (MMCSs) are synthesized by the polymerization of colloidal silica-entrapped resorcinol/formaldehyde in the presence of ammonia as catalyst, followed by carbonization, sodium hydroxide (NaOH) etching to remove silica template, and potassium hydroxide (KOH) activation. The morphology and microstructure are characterized by scanning electron microscopy, transmission electron microscopy, and nitrogen adsorption–desorption. The results show that a typical sample (denoted as MMCS-3) unites the characteristics of regular spherical shape (uniform diameters of 500 nm), high specific surface area (1,620 m² g^?1), large pore volume (1.037 cm³ g^?1), and combined micropores and mesopores (11.0 nm), which endows MMCS-3 good electrochemical performance. MMCS-3 as supercapacitor electrode shows a specific capacitance of 314 F g^?1 under a current density of 0.5 A g^?1 and low internal resistance of 0.2 Ω in 6 M KOH aqueous solution. The electrochemical capacitance still retains 198 F g^?1 at a high current density of 10 A g^?1. After 500 cycle numbers of galvanostatic charge/discharge at 0.5 A g^?1, MMCS-3 electrode still remains the specific capacitance of 301 F g^?1 with the retention of 96 %. This study highlights the potential of well-designed MMCSs as electrodes for widespread supercapacitor applications.     

Hybrid system of nickel<Emphasis Type="Bold">–</Emphasis>cobalt hydroxide on carbonised natural cellulose materials for supercapacitors

Advanced carbon materials formed from abundant biomass are an exciting and promising class for energy devices due to the clear advantages of low cost, sustainability and good physical and electrochemical properties. However, these materials typically do not compete well with their metal functionalised counterparts. In this work, we demonstrate that xCo(OH)₂–(1?x)Ni(OH)₂ with various Ni:Co ratios can be deposited onto biomass-derived carbon to make a hybrid inorganic-carbon electrode with tuneable physical features and electrochemical performance. These features were tuned by adjusting the Ni:Co ratio within precursor solutions. The electrodes had shown a capacitance ranging from 780.7 to 2041 F g^?1, which is very close to the theoretical value for Ni(OH)₂ (2365 F g^?1). A hypothesis is presented to help explain this performance for a modified, biomass-derived carbon electrode.     

Facile synthesis of 5A zeolite from attapulgite clay for adsorption of <Emphasis Type="Italic">n</Emphasis>-paraffins

5A zeolites were facilely synthesized from attapulgite clay and sodium aluminate precursors. The optimum synthesis condition for 4A zeolite (Na-form) were H₂O/attapulgite ratio of 40:1 volume/mass, NaOH/attapulgite mass ratio of 2.35:1, the crystallization time was 4 h at 80–85 °C. The 4A zeolite was converted to related 5A zeolite (Ca-form) through ionic exchanges using calcium chloride solution with the Si/Al mole ratio of 1.3. SEM images demonstrated that as-synthesized 5A zeolites are ordered cubic crystals, average crystals length dimension is 1–2 μm. And the zeolites product had a specific surface area of 482 m² g^?1 and total pore volume of 0.274 cm³ g^?1. The static adsorption experiments showed that the equilibrium adsorption capacities of n-decane and n-pentadecane on produced 5A zeolite were 0.253 and 0.510 g g^?1, respectively. And the adsorption equilibrium time of n-decane and n-pentadecane on 5A zeolite were 45 and 60 min, respectively. The experimental adsorption data of n-decane and n-pentadecane on three zeolites could be properly fitted by the Langmuir–Freundlich isotherm model.     

Preparation,characterization, and evaluation of LiNi0.4Co0.6O2 nanofibers for supercapacitor applications

We prepared LiNi_0.4Co_0.6O₂ nanofibers by electrospinning at the calcination temperature of 450 °C for 6 h. The prepared LiNi_0.4Co_0.6O₂ nanofibers was characterized by thermal, X-ray diffraction, and Fourier transform infrared (FTIR) studies. The morphology of LiNi_0.4Co_0.6O₂ nanofibers was characterized by scanning electron microscopy studies. The asymmetric supercapacitor was fabricated using LiNi_0.4Co_0.6O₂ nanofibers as positive electrode and activated carbon (AC) as negative electrode and a porous polypropylene separator in 1 M LiPF₆–ethylene carbonate/dimethyl carbonate (LiPF₆–EC:DMC) (1:1?v/v) as electrolyte. Cyclic voltammetry studies were then carried out in the potential range of 0 to 3.0 V at different scan rates which exhibited the highest specific capacitance of 72.9 F g^?1. The electrochemical impedance measurements were carried out to find the charge transfer resistance and specific capacitance of the cell, and they were found to be 5.05 Ω and 67.4 F g^?1, respectively. Finally, the charge–discharge studies were carried out at a current density of 1 mA cm^?2 to find out the discharge-specific capacitance, energy density, and power density of the capacitor cell, and they were found to be 70.9 F g^?1, 180.2 Wh kg^?1, and 248.0 W kg^?1, respectively.     

Titanium dioxide/graphene oxide composite and its application as an anode material in non-flammable electrolyte based on ionic liquid and sulfolane

A composite of aminosilane-grafted TiO₂ (TA) and graphene oxide (GO) was prepared via a hydrothermal process. The TiO₂/graphene oxide-based (TA/GO) anode was investigated in an ionic liquid electrolyte (0.7 M lithium bis(trifluoromethanesulfonyl)imide (LiNTf₂)) in ionic liquid (N-methyl-N-propylpyrrolidinium bis(trifluoromethanesulfonyl)imide (MPPyrNTf₂)) at room temperature and in sulfolane (1 M lithium hexafluorophosphate (LiPF₆) in tetramethylene sulfolane (TMS)). Scanning and transmission electron microscopy (SEM and TEM) observations of the anode materials suggested that the electrochemical intercalation/deintercalation process in the ionic liquid electrolyte with vinylene carbonate (VC) leads to small changes on the surface of TA/GO particles. The addition of VC to the electrolyte (0.7 M LiNTf₂ in MPPyrNTf₂ + 10 wt.% VC) considerably increases the anode capacity. Electrodes were tested at different current regimes in the range 5–50 mA g^?1. The capacity of the anode, working at a low current regime of 5 mA g^?1, was ca. 245 mA g^?1, while a current of 50 mA g^?1 resulted in a capacity of 170 mA g^?1. The decrease in anode capacity with increasing current rate was interpreted as the result of kinetic limits of electrode operation. A much lower capacity was observed for the system TA/GO│1 M LiPF₆ in TMS + 10 wt.% VC│Li.     

KOH direct treatment of kombucha and in situ activation to prepare hierarchical porous carbon for high-performance supercapacitor electrodes

Kombucha, a renewable biomass, has been successfully utilized as an accessible carbon source to fabricate kombucha-derived hierarchical porous carbon (KHPC) by KOH direct treatment and in situ activation. The prepared KHPC shows an interconnected hierarchical porous structure, a pore volume of 0.41 cm³ g^?1, and a specific surface area of 917 m² g^?1. Due to the multiple synergistic effects of these advantages, the KHPC-3 exhibits a high specific capacitance of 326 F g^?1 at a current density of 1 A g^?1 in 6 M KOH, good rate capability of 82% retention from 1 to 20 A g^?1, and cycling performance with 91.3% retention over 5000 cycles. Moreover, the KHPC-3 symmetric supercapacitor reveals a good energy density of 20.97 Wh kg^?1 at a power density of 871.2 W kg^?1 and retains 8.08 Wh kg^?1 at 6330 W kg^?1 in 1 M Na₂SO₄ electrolyte. Therefore, the KHPC obtained via the simple synthesis process shows great promise as an electrode material in energy storage devices.