双硫腙修饰固体银汞合金电极吸附伏安法测定痕量铅

制作了银汞合金电极,在其表面用双硫腙进行修饰,溶液中铅离子与电极表面的双硫腙发生螯合作用被富集。当电极电位在-0.20~-0.70V间进行阴极化扫描时,配合物中铅离子在电极表面被还原,于-0.40V左右形成灵敏的还原峰。选择了反应介质并优化了pH值、双硫腙用量、富集时间等实验参数。利用该修饰电极测定铅的线性范围为0.02~1.2mg/L,检出限为10μg/L。对0.6mg/L Pb2 溶液进行11次平行测定,相对标准偏差为4.1%。该法用于实际水样铅的测定,回收率为94.8%。     

兰索拉唑的电化学分析

在NaH2 PO4-Na2 HPO4溶液中,用循环伏安法、差分脉冲伏安法(DSV)和方波伏安法(SWV)在玻碳电极(GCE)上对兰索拉唑进行了电化学研究,发现兰索拉唑在-1.3伏左右有一个明显的阴极还原峰,考察了不同底液及pH、扫描速度、富集时间和静止时间的影响,DSV法线性范围为6.0×10-6～ 1.0×10-3m...     

碳糊电极吸附溶出伏安法测定游离钙

基于Ca(Ⅱ)-茜素红S(ARS)络合物在碳糊电极上的还原波,建立了吸附溶出伏安测定游离钙的新方法。在1.5×10-2mol/LKOH-2.0×10-5mol/LARS介质中,Ca(Ⅱ)-ARS络合物在碳糊电极上于-0.89V处产生一吸附还原波。当富集电位为.0.1V,富集时间90s,扫描速度为100mV/s时,该络合物单扫描阴极溶出峰的二阶导数峰电流与游离钙离子浓度在3.0×10-8~2.0×10-6mol/L范围内呈线性关系;检出限为9.4×10-9mol/L。在0.2mol/LHCl中清洗2min,该电极重现性良好。该方法可用于血清、牛奶和自来水中游离钙的测定。     

Fe(Ⅲ)-草酸-葡萄糖酸钙媒质体系间接电化学还原及棉织物染色的研究

应用循环伏安法研究了Fe(Ⅲ)-草酸-葡萄糖酸钙媒质体系的电化学行为及其可能的反应机理,实验表明Fe(Ⅱ)-葡萄糖酸盐起着最终的还原作用。电解还原时间、工作电压和阴极面积这三个因素影响着电流效率,在Fe(Ⅲ)-草酸-葡萄糖酸钙媒质体系中,还原大红R的电流效率最高可达89%,其电解还原时间10min,工作电压4V,阴极面积40cm2。     

在LiCl-KCl-NaCl熔盐体系中碳的阴极还原的研究

用循环伏安法和电位阶跃法研究了LiCl-KCl-NaCl熔盐体系中碳的阴极还原机理。在钨、铂、不锈钢等微电极上得到的伏安图表明碳的还原是由CO_3~(2-)离子经一步电化学反应实现的,电极反应速度控制步骤为CO_3~(2-)离子向阴极的扩散过程,还原过程具有反应物吸附特征。碳在W、Pt、不锈钢电极上析出电位分别为-2.05V、-1.745V和-1.90V(均相对于Ag/AgCl参比电极)。     

电化学法制备甘露醇阴极液中还原糖的测定

根据电化学制备甘露醇反应体系特征，研究了分光光度法测定阴极液中的还原糖，标准曲线回归方程为Y=0．2151ρ-0．0021，r=0．9999，25倍量的甘露醇和山梨醇对还原糖的测定基本无干扰，阴极液中的加标平均回收率为100．2％。     

氧气在阴极的电还原及其应用研究进展

本文综述了氧阴极电还原的研究进展，着重介绍了阴极表面修饰对该过程的影响以及氧阴极电还原在有机物电合成与废水处理方面的研究进展。     

泡沫铜电极电还原去除溴酸盐研究

电化学还原去除水中溴酸盐的研究表明,与石墨、碳纸及泡沫镍电极相比,泡沫铜电极对溴酸盐的去除效率较高.溴酸盐电化学还原速率随阴极电势降低先升高后降低.低pH条件下,溴酸盐电还原速率较高.初始溴酸盐浓度在50~350μg/L范围内,当阴极电势高于-1.5 V时,溴酸盐电还原过程受电子转移和溴酸盐扩散共同控制;当阴极电势小于-1.5 V时,溴酸盐的还原过程控速步骤主要是浓度扩散.溶解性有机物对溴酸盐电还原过程有明显的抑制作用.该电化学体系中,溴酸盐几乎彻底被还原为等量溴离子,溶液pH略有上升.自来水中溴酸盐的还原速率略低于去离子水.通过XPS分析了电化学还原反应前后泡沫铜电极上的Cu和O价态变化.     

邻苯三酚红修饰碳糊电极吸附伏安法测定痕量铜

报道了采用邻苯三酚红修饰碳糊电极测定痕量铜的方法。通过在邻苯二甲酸氢钾 -氢氧化钠 (p H4.5)介质中富集 ,Cu2 +和邻苯三酚红形成络合物富集于电极表面 ,然后转换到 0 .0 50 mol· L-1的 H3PO4 中 ,经阴极还原后再进行阳极溶出伏安法测定。Cu2 +浓度在 1 .6× 1 0 -9～ 2 .8× 1 0 -7mol·L-1范围内与二次导数峰电流呈线性关系 ,检出限达 8× 1 0 -10 mol·L-1。同时 ,对电极反应机理进行了探讨。应用于合金样的测定 ,取得满意的结果。     

TOPO化学修饰碳糊电极阴极伏安法测定金

本文研究了TOPO—化学修饰碳糊电极测定金。在不加电压情况下于0.1～1.0mol·L-~1HCl介质中进行化学富集,+0.6V～-0.1V范围阴极扫描,+0.20V出现的还原峰高与金浓度0.4～1000ng.ml~(-1)范围内成线性关系。改换底液溶出时,铁允许量可达10000倍而不干扰金的测定。用于合金样品中金的测定,结果满意。并讨论了电极反应的机理。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.