Structural, optical and morphological studies on laser ablated nanostructured WO3 thin films

Thin films of tungsten trioxide (WO₃) are prepared by reactive pulsed laser deposition (PLD) technique on glass substrates at three different substrate temperatures (T_s). The structural, morphological and optical properties of the deposited films are systematically studied using X-ray diffraction (XRD), grazing incidence X-ray diffraction (GIXRD), micro-Raman spectroscopy, scanning electron microscopy (SEM), atomic force microscopy (AFM) and UV-VIS spectrophotometry techniques. X-ray diffraction analysis reveals that crystalline WO₃ films can grow effectively even at 300 K at an oxygen pressure of 0.12 mbar. All the films deposited at various T_s exhibit mixed oxide phase consisting of orthorhombic and triclinic phase of tungsten oxide with a preferred orientation along (0 0 1) lattice plane reflection. Micro-Raman results are consistent with X-ray diffraction findings. The SEM analysis shows that deposited films are porous and crystalline grains are of nano-metric dimension. The effect of T_s on mean surface roughness studied by AFM analysis reveals that mean surface roughness decreases with increase in T_s. The optical response of WO₃ layers measured using UV-VIS spectrophotometry is used to extract the optical constants such as refractive index (n), extinction coefficient (k) and optical band gap (E_g), following the method of Swanepoel.     

Effect of substrate temperature on structural, optical and electrical properties of pulsed laser ablated nanostructured indium oxide films

Nanocrystalline indium oxide (INO) films are deposited in a back ground oxygen pressure at 0.02 mbar on quartz substrates at different substrate temperatures (T_s) ranging from 300 to 573 K using pulsed laser deposition technique. The films are characterized using GIXRD, XPS, AFM and UV-visible spectroscopy to study the effect of substrate temperature on the structural and optical properties of films. The XRD patterns suggest that the films deposited at room temperature are amorphous in nature and the crystalline nature of the films increases with increase in substrate temperature. Films prepared at T_s ≥ 473 K are polycrystalline in nature (cubic phase). Crystalline grain size calculation based on Debye Scherrer formula indicates that the particle size enhances with the increase in substrate temperature. Lattice constant of the films are calculated from the XRD data. XPS studies suggest that all the INO films consist of both crystalline and amorphous phases. XPS results show an increase in oxygen content with increase in substrate temperature and reveals that the films deposited at higher substrate temperatures exhibit better stoichiometry. The thickness measurements using interferometric techniques show that the film thickness decreases with increase in substrate temperature. Analysis of the optical transmittance data of the films shows a blue shift in the values of optical band gap energy for the films compared to that of the bulk material owing to the quantum confinement effect due to the presence of quantum dots in the films. Refractive index and porosity of the films are also investigated. Room temperature DC electrical measurements shows that the INO films investigated are having relatively high electrical resistivity in the range of 0.80-1.90 Ωm. Low temperature electrical conductivity measurements in the temperature range of 50-300 K for the film deposited at 300 K give a linear Arrhenius plot suggesting thermally activated conduction. Surface morphology studies of the films using AFM reveal the formation of nanostructured indium oxide thin films.     

Microstructural studies of bulk and thin film GDC

Ceria rare earth solid solutions are known as solid electrolyte with potential application in oxygen sensors and solid oxide fuel cells. We report the preparation of gadolinia-doped ceria, Ce_0.90Gd_0.10O_1.95, by the conventional solid-state reaction method and the preparation of thin films from a sintered pellet of gadolinia-doped ceria by the pulsed laser deposition technique. The effect of process conditions, such as substrate temperature, oxygen partial pressure, and laser energy on microstructural properties of these films are examined using powder X-ray diffraction, scanning electron microscopy, atomic force microscopy, and Raman spectroscopy.     

Highly conductive and transparent laser ablated nanostructured Al: ZnO thin films

Al doped ZnO thin films are prepared by pulsed laser deposition on quartz substrate at substrate temperature 873 K under a background oxygen pressure of 0.02 mbar. The films are systematically analyzed using X-ray diffraction, atomic force microscopy, micro-Raman spectroscopy, UV-vis spectroscopy, photoluminescence spectroscopy, z-scan and temperature-dependent electrical resistivity measurements in the temperature range 70-300 K. XRD patterns show that all the films are well crystallized with hexagonal wurtzite structure with preferred orientation along (0 0 2) plane. Particle size calculations based on XRD analysis show that all the films are nanocrystalline in nature with the size of the quantum dots ranging from 8 to 17 nm. The presence of high frequency E₂ mode and longitudinal optical A₁ (LO) modes in the Raman spectra suggest a hexagonal wurtzite structure for the films. AFM analysis reveals the agglomerated growth mode in the doped films and it reduces the nucleation barrier of ZnO by Al doping. The 1% Al doped ZnO film presents high transmittance of ∼75% in the visible and near infrared region and low dc electrical resistivity of 5.94 × 10⁻⁶ Ω m. PL spectra show emissions corresponding to the near band edge (NBE) ultra violet emission and deep level emission in the visible region. Nonlinear optical measurements using the z-scan technique shows optical limiting behavior for the 5% Al doped ZnO film.     

Cobalt and tantalum additions for enhanced electrochromic performances of nickel-based oxide thin films grown by pulsed laser deposition

Aiming at improving the durability of anodic electrochromic nickel oxide thin films, Ni-M-O (M = Co, Ta) thin films were grown by pulsed laser deposition (PLD), using optimized conditions, namely room temperature and 10⁻¹ mbar oxygen pressure. For low Co and Ta contents (<5%), both additions lead to a loss of the [1 1 1] preferred orientation of the NiO rock-salt structure followed by a film amorphization with increasing Ta amount. Among the two series of metal additions (M ≤ 20%), the Ni-Co-O (5% Co) and Ni-Ta-O (10% Ta) thin films show the highest electrochemical performances especially in respect of improved durability. If the enhanced properties are associated with a limited dissolution of the oxidized phase for the Ni-Ta-O system, the opposite trend is observed for the Ni-Co-O system as compared to pure NiO.     

SERS activity of pulsed laser ablated silver thin films with controlled nanostructure

The surface‐enhanced Raman scattering (SERS) activity of silver thin films deposited by the pulsed laser ablation technique was investigated. The samples were grown in a controlled Ar atmosphere at pressures ranging between 10 and 70 Pa, and changing the number of laser pulses. Different surface morphologies, from isolated nearly spherical nanoparticles (NPs) to larger islands with smooth edges, were observed by means of scanning and transmission electron microscopies, as a function of the different deposition conditions adopted. SERS measurements were performed by soaking the samples in rhodamine 6G aqueous solutions over the concentration range between 1.0 × 10⁻⁴ and 5.0 × 10⁻⁸ M . Raman spectra were acquired using both the 632.8 and 514.5 nm excitation sources. The dependence of the SERS activity of the samples on the observed surface morphology is presented and discussed. The presence of the so called hot spots is envisaged. Copyright © 2011 John Wiley & Sons, Ltd.     

Influence of deposition conditions on nanostructured InSe thin films

In this study, nanostructured indium selenide (InSe) thin films were deposited on Indium tin oxide (ITO)-coated glass substrate using electrochemical deposition (ECD) from aqueous solution containing In(SO₄)₃.H₂O and SeO₂. The effects of deposition potential (−0.70 to −1.35 V), time (30-3600 s), temperature (25-80 °C) and pH (2.58 for A samples; 2 for B samples and 1.45 for C samples) on growth of the InSe thin films were examined in terms of their structural, morphological and optical properties. X-ray diffraction (XRD) analysis confirmed that the InSe thin films are in polycrystalline structure. It was found that the values of grain size decreased and the full width half maximum (FWHM) values increased with the increasing deposition potential. According to the absorption measurements, optical properties of the thin films varied with changes in deposition conditions. Based on the atomic force microscopy (AFM) and the scanning electron microscopy (SEM) images, surface morphology of the thin films was influenced by deposition potential and pH of the electrolyte, and non-homogeneous depositions distributed across the entire surface were observed. In addition, Raman spectroscopy, X-ray photoelectron spectroscopy (XPS) and fourier transform infrared spectroscopy (FT-IR) analyses were used to further examine crystal quality, vibration, chemical binding conditions, In/Se orientation and structure of the prepared InSe thin films. When Raman results are examined, the B12 sample shows a more intensity and narrow peak at 248 cm⁻¹. XPS measurements sowed that A6 sample exhibited more growth in low potential for a long time and better film stoichiometry compared to the other three samples. Also, FT-IR studies prove the presence of InSe. According to the results, the film did not form at low temperatures and short times. However, the film formation began with the increasing deposition temperature and time at the low potential value of −0.730 V. But, it is clear that a high quality film can be obtained in cathodic potential with −1.3 V and shorter deposition time with 300 s at room temperature respectively. Overall results showed that the high quality thin films can be obtained by the ECD technique. However, deposition conditions must be sensitively adjusted to control morphology of the electrodeposited nanoparticles.     

Influence of oxygen partial pressure on the properties of pulsed laser deposited nanocrystalline zirconia thin films

ZrO₂ thin films were deposited at various oxygen partial pressures (2.0 × 10⁻⁵-3.5 × 10⁻¹ mbar) at 973 K on (1 0 0) silicon and quartz substrates by pulsed laser deposition. The influence of oxygen partial pressure on structure, surface morphology and optical properties of the films were investigated. X-ray diffraction results indicated that the films are polycrystalline containing both monoclinic and tetragonal phases. The films prepared in the oxygen partial pressures range 2.0 × 10⁻⁵-3.5 × 10⁻¹ mbar contain nanocrystals of sizes in the range 54-31 nm for tetragonal phase. The peak intensity of the tetragonal phase decreases with the increase of oxygen partial pressures. Surface morphology of the films examined by AFM shows the formation of nanostructures. The RMS surface roughness of the film prepared at 2.0 × 10⁻⁵ mbar is 1.3 nm while it is 3.2 nm at 3.5 × 10⁻¹ mbar. The optical properties of the films were investigated using UV-visible spectroscopy technique in the wavelength range of 200-800 nm. The refractive index is found to decrease from 2.26 to 1.87 as the oxygen partial pressure increases from 2.0 × 10⁻⁵ to 3.5 × 10⁻¹ mbar. The optical studies show two different absorption edges corresponding to monoclinic and tetragonal phases.     

Effect of Al doping on structural,optical and electrical properties of SnO2 thin films synthesized by pulsed laser deposition

Aluminium-doped (Al = 0–5?wt.%) SnO₂ thin films with low-electrical resistivity and high optical transparency have been successfully synthesized by pulsed laser deposition technique at 500 °C. Structural, optical and electrical properties of the as-deposited and post-annealed thin films were investigated. X-ray diffraction patterns suggest that the films transform from crystalline to amorphous state with increasing aluminium content. The root mean square (R_q) surface roughness parameter, determined by atomic force microscopy decreases upon annealing of the as-deposited film. While resistivity of the film is the lowest (9.49 × 10^?4 Ω-cm) at a critical doping level of 1?wt.% Al, optical transparency is the highest (nearly 90%) in the as-deposited condition. Temperature dependence of the electrical resistivity suggests that the Mott’s variable range hopping process is the dominant carrier transport mechanism in the lower temperature range (40–135 K) for all the films whereas, thermally activated band conduction mechanism seems to account for conduction in the higher temperature region (200–300 K).     

Doped thin metal oxide films for catalytic gas sensors

TiO₂ and Pt doped TiO₂ thin films were grown by pulsed laser deposition on 〈0 0 1〉 SiO₂ substrates. The doped films were compared with undoped ones deposited in similar experimental conditions. An UV KrF* (λ = 248 nm, τ_FWHM ≅ 20 ns, ν = 2 Hz) excimer laser was used for the irradiation of the TiO₂ or Pt doped TiO₂ targets. The substrate temperatures were fixed during the growth of the thin films at values within the 300-500 °C range. The films’ surface morphology was investigated by atomic force microscopy and their crystalline quality by X-ray diffractometry. The corresponding transmission spectra were recorded with the aid of a double beam spectrophotometer in the spectral range of 400-1100 nm. No contaminants or Pt segregation were detected in the synthesized anatase phase TiO₂ thin films composition. Titania crystallites growth inhibition was observed with the increase of the dopant concentration. The average optical transmittance in the visible-infrared spectral range of the films is higher than 85%, which makes them suitable for sensor applications.     

Effect of annealing on the surface and band gap alignment of CdZnS thin films

Effects of the annealing temperature on structural, optical and surface properties of chemically deposited cadmium zinc sulfide (CdZnS) films were investigated. X-ray diffraction (XRD) results showed that the grown CdZnS thin films formed were polycrystalline with hexagonal structure. Atomic force microscopy (AFM) studies showed that the surface roughness of the CdZnS thin films was about 60-400 nm. Grain sizes of the CdZnS thin films varied between 70 and 300 nm as a function of annealing temperature. The root mean square surface roughness of the selected area, particular point, average roughness profile, topographical area of roughness were measured using the reported AFM software. The band gaps of CdZnS thin films were determined from absorbance measurements in the visible range as 300 nm and 1100 nm, respectively, using Tauc theory.     

Preparation and characterizations of amorphous nanostructured SiC thin films by low energy pulsed laser deposition

Amorphous silicon carbide (SiC) thin films were deposited on silicon substrates by pulsed laser ablation at room temperature. Thicknesses and surface morphology of the thin films were characterized using optical profilers, atomic force and field emission scanning electron microscopy. Nanohardnes, modulus and scratch resistance properties were determined using XP nanoindenter. The results show that crack free, smooth and nanostructured thin films can be deposited using low laser energy densities.     

Investigation of transmittance property of Palladium thin films fabricated by pulsed laser deposition with polarization using single layer model

In this paper the structure, morphology and optical properties of Pd thin films deposited on glass substrate by pulse laser deposition technique at two different substrate temperatures have been investigated. The fabricated films were characterized by various methods such as XRD, AFM, and UV-vis-NIR spectroscopy. The influence of surface roughness and angle of incidence with p polarization was investigated experimentally by optical property of palladium (Pd) thin films of two different thicknesses and rms roughness from transmission measurement in the visible spectral range. It has been shown that the experimental transmittance spectra agree well with their theoretical values for absorbing Pd thin film. The transmittance of thin film increases with increase in incident angle for the same sample.     

Pulsed laser deposition of doped skutterudite thin films

Ca_xCo₄Sb₁₂ skutterudite thin films have been prepared by pulsed laser deposition using a Nd:YAG laser working at 532 or 266 nm of wavelength. Characterization has been carried out by X-ray diffraction, atomic force microscopy and scanning electron microscopy. Emphasis has been put on the difficulty to obtain the skutterudite phase. Influence of the deposition temperature, the way of sticking the substrate, the laser fluence, the base pressure prior to deposition and the laser wavelength has been studied. All parameters revealed to have a drastic effect, and the skutterudite could only be achieved in a very narrow range of temperature and laser fluence, for a given wavelength, showing the importance on how these parameters are measured to ensure reproducible results.     

Structural and morphological properties of thin ZnO films grown by pulsed laser deposition

The pulsed laser deposition technique was used to produce zinc oxide thin films onto silicon and Corning glass substrates. Homogeneous surfaces exhibiting quite small Root Mean Square (RMS) roughness, consisting of shaped grains were obtained, their grain diameters being 40-90 nm at room temperature and at 650 °C growth respectively. Films were polycrystalline, even for growth at room temperature, with preferential crystallite orientation the (0 0 2) basal plane of wurtzite ZnO. Temperature increase caused evolution from grain to grain agglomeration structures, improving crystallinity. Compressive to tensile stresses transition with temperature was found while the lattice constant decreased.     

Reactive pulsed laser deposition of gold nitride thin films

We report on the growth and characterization of gold nitride thin films on Si 〈1 0 0〉 substrates at room temperature by reactive pulsed laser ablation. A pure (99.95%) Au target was ablated with KrF excimer laser pulses in nitrogen containing atmosphere (N₂ or NH₃). The gas ambient pressure was varied in the range 0.1-100 Pa. The morphology of the films was studied by using optical, scanning electron and atomic force microscopy, evidencing compact films with RMS roughness in the range 3.6-35.1 nm, depending on the deposition pressure. Rutherford backscattering spectrometry and energy dispersion spectroscopy (EDS) were used to detect the nitrogen concentration into the films. The EDS nitrogen peak does not decrease in intensity after 2 h annealing at 250 °C. Film resistivity was measured using a four-point probe and resulted in the (4-20) × 10⁻⁸ Ω m range, depending on the ambient pressure, to be compared with the value 2.6 × 10⁻⁸ Ω m of a pure gold film. Indentation and scratch measurements gave microhardness values of 2-3 GPa and the Young's modulus close to 100 GPa. X-ray photoemission spectra clearly showed the N 1s peak around 400 eV and displaced with respect to N₂ phase. All these measurements point to the formation of the gold nitride phase.     

Swift heavy ion induced modifications in cobalt doped ZnO thin films: Structural and optical studies

Modifications in the structural and optical properties of 100 MeV Ni⁷⁺ ions irradiated cobalt doped ZnO thin films (Zn_1−xCo_xO, x = 0.05) prepared by sol-gel route were studied. The films irradiated with a fluence of 1 × 10¹³ ions/cm² were single phase and show improved crystalline structure with preferred C-axis orientation as revealed from XRD analysis. Effects of irradiation on bond structure of thin films were studied by FTIR spectroscopy. The spectrum shows no change in bonding structure of Zn-O after irradiation. Improved quality of films is further supported by FTIR studies. Optical properties of the pristine and irradiated samples have been determined by using UV-vis spectroscopic technique. Optical absorption spectra show an appreciable red shift in the band gap of irradiated Zn_1−xCo_xO thin film due to sp-d interaction between Co²⁺ ions and ZnO band electrons. Transmission spectra show absorption band edges at 1.8 eV, 2.05 eV and 2.18 eV corresponding to d-d transition of Co²⁺ ions in tetrahedral field of ZnO. The AFM study shows a slight increase in grain size and surface roughness of the thin films after irradiation.     

Growth of oxide thin films for optical gas sensor applications

Tungsten trioxide and titanium dioxide thin films were synthesised by pulsed laser deposition. We used for irradiations of oxide targets an UV KrF* (λ = 248 nm, τ_FWHM ≅ 20 ns, ν = 2 Hz) excimer laser source, at 2 J/cm² incident fluence value. The experiments were performed in low oxygen pressure. The (0 0 1) SiO₂ substrates were heated during the thin film deposition process at temperature values within the 300-500 °C range. The structure and crystalline status of the obtained oxide thin films were investigated by high resolution transmission electron microscopy. Our analyses show that the films are composed by nanoparticles with average diameters from a few to a few tens of nm. Moreover, the films deposited at substrate temperatures higher than 300 °C are crystalline. The tungsten trioxide films consist of a mixture of triclinic and monoclinic phases, while the titanium dioxide films structure corresponds to the tetragonal anatase phase. The oxide films average transmittance in the visible-infrared spectral range is higher than 80%, which makes them suitable for sensor applications.     

Effect of different annealing temperature on Sb-doped ZnO thin films prepared by pulsed laser deposition on sapphire substrates

Influence of annealing temperature on the properties of Sb-doped ZnO thin films were studied. Hall measurement results indicated that the Sb-doped ZnO annealed at 950 °C was p-type conductivity. X-ray diffraction (XRD) results indicated that the Sb-doped ZnO thin films prepared at the experiments are high c-axis oriented. It was worth noting that p-type sample had the worst crystallinity. The measurements of low-temperature photoluminescence (PL) spectra indicate that the sample annealed at the temperatures of 950 °C showed strong acceptor-bound exciton (A⁰X) emission, and confirmed that it is related to Sb-doping by comparing with the undoped ZnO low-temperature PL spectrum.     

Structural characterization and magnetoresistance of manganates thin films and Fe-doped manganates thin films

Perovskites thin films with the composition La_0.6Ca_0.4MnO₃ doped with 20% Fe, were prepared by pulsed reactive crossed beam laser ablation, where a synchronized reaction gas pulse interacts with the ablation plume. The films were grown on various substrates and the highest colossal magnetoresistance ratio (CMR) was detected by Hall measurements for films grown on LaAlO₃ (1 0 0), which was selected as substrate for further investigations.Several growth parameters, such as substrate temperature and target to substrate distance were varied to analyze their influence on the film properties.The structure of the deposited thin films was characterized by X-ray diffraction and atomic force microscope, while Rutherford backscattering (RBS) was used to determine the film stoichiometry. The electrical properties were determined by Hall effect measurements in a magnetic field of 0.51 T.These measurements reveal that the amplitude of the CMR ratio depends strongly on the substrate and that the oxygen content influences the temperature where the transition from semiconductor to metal is observed.