Deposition and characterization of binary Al2O3/SiO2 coating layers on the surfaces of rutile TiO2 and the pigmentary properties

Binary Al₂O₃/SiO₂-coated rutile TiO₂ composites were prepared by a liquid-phase deposition method starting from Na₂SiO₃·9H₂O and NaAlO₂. The chemical structure and morphology of binary Al₂O₃/SiO₂ coating layers were investigated by Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, TG-DSC, Zeta potential, powder X-ray diffraction, and transmission electron microscopy techniques. Binary Al₂O₃/SiO₂ coating layers both in amorphous phase were formed at TiO₂ surfaces. The silica coating layers were anchored at TiO₂ surfaces via Si-O-Ti bonds and the alumina coating layers were probably anchored at the SiO₂-coated TiO₂ surfaces via Al-O-Si bonds. The formation of continuous and dense binary Al₂O₃/SiO₂ coating layers depended on the pH value of reaction solution and the alumina loading. The binary Al₂O₃/SiO₂-coated TiO₂ composites had a high dispersibility in water. The whiteness and brightness of the binary Al₂O₃/SiO₂-coated TiO₂ composites were higher than those of the naked rutile TiO₂ and the SiO₂-coated TiO₂ samples. The relative light scattering index was found to depend on the composition of coating layers.     

Effects of coating parameters on the morphology of SiO2-coated TiO2 and the pigmentary properties

SiO₂-coated TiO₂ powders were prepared by the chemical deposition method starting from rutile TiO₂ and Na₂SiO₃. The SiO₂-coated TiO₂ powders were characterized by X-ray photoelectron spectroscopy, Zeta-potential analysis, Fourier transform infrared spectroscopy, and transmission electron microscopy. The evolution of island-like and uniform coating layers was found to depend upon the ratio of Na₂SiO₃ to TiO₂, reaction temperature, and pH. The whiteness and brightness of the SiO₂-coated TiO₂ powders increased in response to an increase in the SiO₂ loading, but there was a maximum value among the light scattering indexes. The SiO₂-coated TiO₂ powders possessed more negative Zeta potentials than the naked TiO₂. The dispersibility of the SiO₂-coated TiO₂ powders with the continuous and uniform SiO₂ coating layers was higher than that of the naked TiO₂ and the SiO₂-coated TiO₂ powders with the island-like SiO₂ coating layers.     

First-principles study of native defects in rutile TiO2

Native point defects in the rutile TiO₂ are studied via first-principles pseudopotential calculations. Except for the two antisite defects, all the native point defects have low formation energies. Under the Ti-rich growth condition, high concentrations of titanium interstitials and oxygen vacancies would form spontaneously in p-type samples; whereas high concentrations of titanium vacancies would form spontaneously in n-type samples regardless of the oxygen partial pressure.     

Synthesis of TiO2 rutile nanoparticles by PLA in solution

This paper describes the synthesis of TiO₂ nanoparticles by laser ablation in solution synthesis (Lasis). The laser excimer beam passes through a focusing lens and it is sent to the reaction chamber. The frequency used during the synthesis was 20 Hz, intensity 26 kV The metal ablated by the laser beam undergoes an oxidation process resulting from the reaction with water. We obtain TiO₂ nanoparticles with average size of 6.5 nm, crystallized in the rutile structure. The crystallographic and morphological structure was studied by transmission electron microscopy.     

Different effects of cerium ions doping on properties of anatase and rutile TiO2

Pure and Ce⁴⁺ doped anatase and rutile TiO₂ were prepared by hydrothermal methods and characterized by XRD, TEM, UV-vis diffusion spectroscopy, and XPS measurements. The photocatalytic reactivity of the catalysts was evaluated by the photodegradation of Rhodamine B (RB) under ultraviolet irradiation. The photocatalytic efficiency of the rutile sample doped with an appropriate amount of Ce⁴⁺ was enhanced while all Ce⁴⁺ doped anatase samples showed a much lower activity than pure anatase. The reasons were discussed     

Evolution of TiO2 coating layers on lamellar sericite in the presence of La and the pigmentary properties

TiO₂-coated sericite powders were prepared by the chemical deposition method starting from lamellar sericite and TiCl₄ in the presence or absence of La³⁺ cations. After calcination at 900 °C for 1 h, the resultant TiO₂ nanoparticles on the sericite surfaces existed in anatase phase. The light scattering indexes of the TiO₂-coated lamellar sericite powders were dozens of times higher than that of the naked lamellar sericite powders. The presence of La³⁺ in the deposition solution was beneficial to the formation of the small-sized anatase TiO₂ nanoparticles, resulting in the formation of the dense and uniform island-like TiO₂ coating layers in a large range of the weight ratios of TiO₂ to sericite from 5% to 20%. The TiO₂-coated lamellar sericite powders prepared in the presence of La³⁺ had higher light scattering index than that prepared in the absence of La³⁺. XPS analysis shows that when La³⁺ cations were absent in the reaction solution, TiO₂ coating layers anchored at the sericite surface via the Ti-O-Si and Ti-O-Al bonds. The presence of La³⁺ cations caused the formation of Si-O-La and Al-O-La bonds at the sericite surface and Ti-O-La bond at the surface of TiO₂ coating layers. After coating TiO₂ on the sericite surface, the yellowness of the TiO₂-coated sericite powders obviously increased and the brightness slightly decreased.     

Growth of branched rutile TiO2 nanorod arrays on F-doped tin oxide substrate

Branched rutile TiO₂ nanorod arrays were directly synthesized on the F-doped tin oxide (FTO) substrate through a two-step hydrothermal treatment by a seeding method with TiO₂-nanorods as seeds. The samples were characterized respectively by means of X-ray diffraction (XRD), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM) and field-emission scanning electron microscopy (FESEM). Results showed that TiO₂ nanorods with nanobranches (TiO₂-NB) grew vertically on the FTO substrate. XRD and HRTEM results confirmed that the TiO₂-NB arrays were single-crystalline rutile. The optical properties of the samples were studied with a UV-vis spectrometer. The photocatalytic activity of the TiO₂-NB film is better than that of P25 particulate film. Direct electrical pathway and improved light-harvesting efficiency were crucial for the superior photocatalytic activity of the TiO₂-NB arrays.     

Hydrogen shallow donors in ZnO and rutile TiO2

A combined study of IR absorption, photoconductivity, photoluminescence and Raman measurements in ZnO samples supports the theoretical suggestions of a shallow bond-centered hydrogen donor and a shallow hydrogen donor within the oxygen vacancy. In rutile TiO₂ we also identify a shallow hydrogen donor in contrast to recent theoretical predictions. A possible solution to this obvious discrepancy is proposed.     

Correlation between microstructure and optical properties of nano-crystalline TiO2 thin films prepared by sol-gel dip coating

Titanium dioxide thin films have been prepared from tetrabutyl-orthotitanate solution and methanol as a solvent by sol-gel dip coating technique. TiO₂ thin films prepared using a sol-gel process have been analyzed for different annealing temperatures. Structural properties in terms of crystal structure were investigated by Raman spectroscopy. The surface morphology and composition of the films were investigated by atomic force microscopy (AFM). The optical transmittance and reflectance spectra of TiO₂ thin films deposited on silicon substrate were also determined. Spectroscopic ellipsometry study was used to determine the annealing temperature effect on the optical properties and the optical gap of the TiO₂ thin films. The results show that the TiO₂ thin films crystallize in anatase phase between 400 and 800 °C, and into the anatase-rutile phase at 1000 °C, and further into the rutile phase at 1200 °C. We have found that the films consist of titanium dioxide nano-crystals. The AFM surface morphology results indicate that the particle size increases from 5 to 41 nm by increasing the annealing temperature. The TiO₂ thin films have high transparency in the visible range. For annealing temperatures between 1000 and 1400 °C, the transmittance of the films was reduced significantly in the wavelength range of 300-800 nm due to the change of crystallite phase and composition in the films. We have demonstrated as well the decrease of the optical band gap with the increase of the annealing temperature.     

Electronic structures and optical properties of rutile TiO2 with different point defects from DFT + U calculations

The electronic states and formation energies of four types of lattice point defects in rutile TiO₂ are studied using the first-principles calculations. The existence of oxygen vacancy leads to a deep donor defect level in the forbidden band, while the Ti interstitial forms two local states. It is predicted that oxygen vacancy prefers to combine with Ti-interstitial to form V_O–Ti_i dimer by a partial 3d electron transfer from the Ti_i to its neighboring V_O. The charge distribution between a Ti interstitial and its neighboring Ti ions partially shields the Coulomb interactions. Lastly, optical properties of these defective lattices are discussed.     

A simple and low temperature process for super-hydrophilic rutile TiO2 thin films growth

We investigate an environmentally friendly aqueous solution system for rutile TiO₂ violet color nanocrystalline thin films growth on ITO substrate at room temperature. Film shows considerable absorption in visible region with excitonic maxima at 434 nm. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), selected area electron diffraction (SAED), UV-vis, water surface contact angle and energy dispersive X-ray analysis (EDX) techniques in addition to actual photo-image that shows purely rutile phase of TiO₂ with violet color, super-hydrophilic and densely packed nanometer-sized spherical grains of approximate diameter 3.15 ± 0.4 nm, characterize the films. Band gap energy of 4.61 eV for direct transition was obtained for the rutile TiO₂ films. Film surface shows super-hydrophilic behavior, as exhibited water contact angle was 7°. Strong visible absorption (not due to chlorine) leaves future challenge to use these films in extremely thin absorber (ETA) solar cells.     

Optical properties of ITO/TiO2 single and double layer thin films deposited by RPLAD

Indium tin oxide (ITO) and titanium dioxide (TiO₂) single layer and double layer ITO/TiO₂ films were prepared using reactive pulsed laser ablation deposition (RPLAD) with an ArF excimer laser for applications in dye-sensitized solar cells (DSSCs). The films were deposited on SiO₂ substrates either at room temperatures (RT) or heated to 200-400 °C. Under optimized conditions, transmission of ITO films in the visible (vis) range was above 89% for films produced at RT and 93% for the ones deposited at higher temperatures. Increasing the substrate temperature from RT to 400 °C enhances the transmission of TiO₂ films in the vis-NIR from about 70% to 92%. High transmission (≈90%) was observed for the double layer ITO/TiO₂ with a transmission cut-off above 900 nm. From the transmission data, the energies gaps (E_g), as well as the refractive indexes (n) for the films were estimated. n ≈ 2.03 and 2.04, respectively for ITO films and TiO₂ film deposited at 400 °C in the visible region. Post-annealing of the TiO₂ films for 3 h at 300 and 500 °C was performed to enhance n. The refractive index of the TiO₂ films increases with the post-annealing temperature. The direct band gap is 3.6, 3.74 and 3.82 eV for ITO films deposited at RT, 200, and 400 °C, respectively. The TiO₂ films present a direct band gap of 3.51 and 3.37 eV for as deposited TiO₂ films and when annealed at 400 °C, respectively. There is a shift of about 0.1 eV between ITO and ITO/TiO₂ films deposited at 200 °C. The shift decreases by half when the TiO₂ film was deposited at 400 °C. Post-annealing was also performed on double layer ITO/TiO₂.     

Fabrication of nitrogen-doped TiO2 layer on titanium substrate

In this paper, macropores TiO₂ layer was fabricated on titanium substrates based on plasma based ion implantation (PBII). In order to increase the photodegradation efficiency of fabricated TiO₂ layer, two approaches are used: (1) preparation of macropores on TiO₂ layer to increase the total photodegradation area and (2) nitrogen doping (N-doping) to increase light absorption efficiency. The fabrication process of the N-doped macropores TiO₂ layer comprises four steps: firstly, helium plasma based ion implantation (He-PBII) is employed to generate He bubbles in substrate; secondly, oxygen plasma based ion implantation (O-PBII) and a followed annealing in air are executed to obtain rutile and anatase mixture TiO₂ phases; thirdly, He bubbles are exposed to the surface via an Ar ion sputter process; lastly, the samples are doped by nitrogen PBII (N-PBII). The photodegradation of Rhodamine B solution under Xe lamp indicates that the TiO₂ layer with surface macropores and N-doping has higher light photocatalysis efficiency.     

Structure and photoluminescence properties of Er3+-doped TiO2-SiO2 powders prepared by sol-gel method

Er 3+-doped TiO 2-SiO 2 powders are prepared by the sol-gel method,and they are characterized by high resolution transmission electron microscopy (HR-TEM),X-ray diffraction (XRD) spectra,and Raman spectra of the samples.It is shown that the TiO 2 nanocrystals are surrounded by an SiO 2 glass matrix.The photoluminescence (PL) spectra are recorded at room temperature.A strong green luminescence and less intense red emission are observed in the samples when they are excited at 325 nm.The intensity of the emission,which is related to the defect states,is strongest at the annealing temperature of 800 C.The PL intensity of Er 3+ ions increases with increasing Ti/Si ratio due to energy transfer between nano-TiO 2 particles and Er 3+ ions.     

Luminescence enhancement in bromine and samarium co-doped TiO2 semiconductor nanocrystalline powders

In this paper, TiO₂:Sm³⁺ (0.75 mol%) nanoparticles doped with different amounts of Br⁻ were prepared by an improved sol-gel method and were characterized by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), VG ESCALAB MKIIX-ray photoelectron spectrometer (XPS) and ultraviolet-visible diffuse reflectance spectroscopy (UV-vis DRS). Their photoluminescence (PL) properties were investigated at room temperature. The emissions of ⁴G_5/2-⁶H_J (J=5/2, 7/2, 9/2) transitions of Sm³⁺ ions were observed under the excitation wavelength at 350 nm and the emission intensity depended strongly on the doping amount of Br⁻. TiO₂:Sm³⁺ (0.75 mol%) nanoparticles doped with 1 mol% of Br⁻ calcined at 700 °C exhibit highest intensity of luminescence, which is nearly three times than the undoped one. The mechanism of photoluminescence in the co-doped system was discussed.     

Strain-induced ferroelectric phase transitions in incipient ferroelectric rutile TiO2

Uniaxial strain induced ferroelectric phase transitions in rutile TiO₂ are investigated by first-principles calculations. The calculated results show that the in-plane tensile strain induces rutile TiO₂, paraelectric phase with P_4-2/mnm (D_4h) space group, to a ferroelectric phase with P_m (C_s) space group,driven by the softening behaviour of the E_u1 mode. In addition, the out-of-plane tensile strain, vertical to the ab plane, leads to a ferroelectric phase with P_42nm (C_4v) space group, driven by the softening behaviour of the A_2u mode. The critical tensile strains are 3.7% in-plane and 4.0% out-of-plane, respectively. In addition, the in-plane compression strain, which has the same structure variation as out-of-plane tensile strain due to Poisson effect, leads the paraelectric rutile TiO₂ to a paraelectric phase with P_nnm (D_2h) space group driven by the softening behaviour of the B_1g mode. These results indicate that the sequence ferroelectric (or paraelectric) phase depends on the strain applied. The origin of ferroelectric stabilization in rutile TiO₂ is also discussed briefly in terms of strain induced Born effective charge transfer.     

Evolution of zirconia coating layer on rutile TiO2 surface and the pigmentary property

Zirconia-coated rutile TiO₂ composites were prepared by the chemical liquid deposition method starting from rutile TiO₂ and ZrOCl₂. The amorphous zirconia coating layers were anchored at the TiO₂ surface via Zr-O-Ti bond. The formation of continuous and dense zirconia coating layers was dependent on the pH value of the reaction solution and the mole ratio of ZrOCl₂ to TiO₂. As compared to the naked rutile TiO₂, the water dispersibility, whiteness, brightness, and relative light scattering index of the zirconia-coated rutile TiO₂ composites were increased.     

锐钛矿相和金红石相TiO2:Nb的光电性能研究

采用基于密度泛函理论的第一性原理计算了锐钛矿相和金红石相TiO₂:Nb的晶体结构、电子结构和光学性质. 结果表明, 在相等的摩尔掺杂浓度下(6.25%), 锐钛矿相TiO₂:Nb的导带底电子有效质量小于金红石相TiO₂:Nb, 且前者室温载流子浓度是后者的两倍左右, 即具有更大的施主杂质电离率, 从而解释了锐钛矿相TiO₂:Nb比金红石相TiO₂:Nb具有更优异电学性能的实验现象. 光学计算也表明锐钛矿相在可见光区有更大的透过率, 从而在理论上解释了锐钛矿相TiO₂:Nb比金红石相TiO₂:Nb更适于做透明导电材料的原因. 计算结果与实验数据能较好符合. 关键词： 2:Nb')" href="#">TiO₂:Nb 第一性原理 电子结构 光学性能     

Influence of growth temperature of TiO2 buffer on structure and PL properties of ZnO films

A series of ZnO films with TiO₂ buffer on Si (1 0 0) substrates were prepared by DC reactive sputtering. Growth temperature of TiO₂ buffer changed from 100 °C to 400 °C, and the influence on the crystal structures and optical properties of ZnO films have been investigated. The XRD results show that the ZnO films with TiO₂ buffer have a hexagonal wurtzite structure with random orientation, and with the increase of growth temperature of TiO₂ buffer, the residual stresses were released gradually. Specially, the UV emission enhanced distinctly and FWHMs (full width half maximum) decreased linearly with the increasing TiO₂ growth temperature. The results all come from the improvement of crystal quality of ZnO films.     

From anodic TiO2 nanotubes to hexagonally ordered TiO2 nanocolumns

We report on the formation of hexagonally ordered TiO₂ nanocolumnar layers by electrochemical oxidation in a fluoride containing electrolyte, using self-organizing nanotube formation conditions at elevated potentials and low temperatures. The influence of the substrate temperature on the nanocolumn morphology and composition is investigated and characterized by FE-SEM and EDX. The origin of these nanocolumns can be attributed to a thickening of the inner tube wall of the double wall structure of self-organized TiO₂ nanotubes. Furthermore, a transition from nanocolumnar to nanotubular structure can be established by changing the applied voltage or applying a post-immersion treatment.