Zinc oxide nanostructures for applications as ethanol sensors and dye-sensitized solar cells

ZnO nanostructures were prepared by thermal oxidation technique for applying as ethanol sensors and dye-sensitized solar cells. To improve sensitivity of the sensor based on ZnO nanostructures, gold doping was performed in ZnO nanostructures. Gold-doped with 0%, 5%, and 10% by weight were investigated. The improvement of sensor sensitivity toward ethanol due to gold doping was observed at entire operating temperature and ethanol concentration. The sensitivity up to 145 was obtained for 10% Au-doped ZnO sensor. This can be explained by an increase of the quantity of oxygen ion due to catalytic effect of gold. Also, it was found that oxygen ion species at the surface of the Au-doped ZnO sensor remained O²⁻ as pure ZnO sensor. For dye-sensitized solar cell application, the dye-sensitized solar cell structure based on ZnO as a photoelectrode was FTO/ZnO/Eosin-Y/electrolyte/Pt counter electrode. ZnO with different morphologies of nanobelt, nano-tetrapod, and powder were investigated. It was found that DSSCs with ZnO powder showed higher photocurrent, photovoltage and overall energy conversion efficiencies than that of ZnO nanobelt and ZnO nano-tetrapod. The best results of DSSCs were the short circuit current (J_sc) of 1.25 mA/cm², the open circuit voltage (V_oc) of 0.45 V, the fill factor (FF) of 0.65 and the overall energy conversion efficiency (η) of 0.68%.     

Enhanced photoelectrochemical performance of ZnO photoanode with scattering hollow cavities

Abstract ZnO nanoparticles with average diameter of 12 nm were used to fabricate ZnO photoanodes by electrohydrodynamic (EHD) technique for dye-sensitized solar cells (DSSCs). To enhance the light scattering and conversion efficiency, the ZnO film with scattering hollow cavities (HCs) was realized by calcining polystyrene spheres (PSs) in the film. The films had strong light scattering ability and the overall light to electricity conversion efficiency (η) was improved and reached 5.5% under illumination of simulated solar light (AM-1.5, 100 mW/cm²).     

电纺ZnO纳米纤维电子传输层提高倒置PTB7∶PC70BM电池效率

研究利用静电纺丝制备的不同直径ZnO纳米纤维作为倒置结构有机太阳能电池的电子传输层对器件转化效率的影响。首先通过静电纺丝技术成功制备了半径在43～110 nm之间的ZnO纳米纤维,然后将ZnO纳米纤维作为电子传输层加入到倒置结构有机太阳能电池（ITO/ZnO∶ZnO nanofiber/PTB7∶PC₇₀BM/MoO₃/Al）。与平面结构的ZnO电子传输层相比,ZnO纳米纤维具有比表面积大等优点,增加了电子传输和抽取能力,提高了器件的光电转化效率。实验发现ZnO纳米纤维的直径越小,电池效率越大。当ZnO纳米纤维直径为(46±5)nm,接收时间为30 s时,作为电子传输层的电池效率提高了8%。     

Micromorph tandem solar cells: optimization of the microcrystalline silicon bottom cell in a single chamber system

We report on the development of single chamber deposition of microcrystalline and micromorph tandem solar cells directly onto low-cost glass substrates. The cells have pin single-junction or pin/pin double-junction structures on glass substrates coated with a transparent conductive oxide layer such as SnO₂ or ZnO. By controlling boron and phosphorus contaminations, a single-junction microcrystalline silicon cell with a conversion efficiency of 7.47% is achieved with an i-layer thickness of 1.2 μm. In tandem devices, by thickness optimization of the microcrystalline silicon bottom solar cell, we obtained an initial conversion efficiency of 9.91% with an aluminum (Al) back reflector without a dielectric layer. In order to enhance the performance of the tandem solar cells, an improved light trapping structure with a ZnO/Al back reflector is used. As a result, a tandem solar cell with 11.04% of initial conversion efficiency has been obtained.     

Co-sensitized quantum dot solar cell based on ZnO nanowire

An efficient photoelectrode is fabricated by sequentially assembled CdS and CdSe quantum dots (QDs) onto a ZnO-nanowire film. As revealed by UV-vis absorption spectrum and scanning electron microscopy (SEM), CdS and CdSe QDs can be effectively adsorbed on ZnO-nanowire array. Electrochemical impedance spectroscopy (EIS) measured demonstrates that the electron lifetime for ZnO/CdS/CdSe (13.8 ms) is calculated longer than that of ZnO/CdS device (6.2 ms), which indicates that interface charge recombination rate is reduced by sensitizing CdSe QDs. With broader light absorption range and longer electron lifetime, a power conversion efficiency of 1.42% is achieved for ZnO based CdS/CdSe co-sensitized solar cell under the illumination of one Sun (AM 1.5G, 100 mW cm⁻²).     

Characterization for metamaterials with a high refractive index formed by periodic stratified metallic wires array

Ultralong ZnO nanowires were successfully prepared on a large scale by a microwave-assisted aqueous route without using any surfactant or template at relatively low temperature of 120°C. The obtained nanowires were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM), and energy-dispersive X-ray spectrum (EDX). The growth mechanism and photoluminescence of the one-dimensional nanostructure, and photovoltaic performances for dye-sensitized solar cell (DSSC) of the nanowires were discussed in detail.     

Interfacial engineering of CuO nanorod/ZnO nanowire hybrid nanostructure photoanode in dye-sensitized solar cell

Developing efficient and cost-effective photoanode plays a vital role determining the photocurrent and photovoltage in dye-sensitized solar cells (DSSCs). Here, we demonstrate DSSCs that achieve relatively high power conversion efficiencies (PCEs) by using one-dimensional (1D) zinc oxide (ZnO) nanowires and copper (II) oxide (CuO) nanorods hybrid nanostructures. CuO nanorod-based thin films were prepared by hydrothermal method and used as a blocking layer on top of the ZnO nanowires’ layer. The use of 1D ZnO nanowire/CuO nanorod hybrid nanostructures led to an exceptionally high photovoltaic performance of DSSCs with a remarkably high open-circuit voltage (0.764 V), short current density (14.76 mA/cm² under AM1.5G conditions), and relatively high solar to power conversion efficiency (6.18%) . The enhancement of the solar to power conversion efficiency can be explained in terms of the lag effect of the interfacial recombination dynamics of CuO nanorod-blocking layer on ZnO nanowires. This work shows more economically feasible method to bring down the cost of the nano-hybrid cells and promises for the growth of other important materials to further enhance the solar to power conversion efficiency.     

Short-circuit current improvement in CdTe solar cells by combining a ZnO buffer layer and a solution back contact

Conventional CdTe solar cells have a CdS window layer, in which an absorption loss of photons with more than 2.4 eV occurs through the CdS layer. A thinner CdS layer was applied to enhance light transmission and a ZnO buffer layer with a band gap of 3.3 eV was introduced to suppress shunting through the thinner CdS window layer. A 100-nm thick ZnO layer sputter-deposited at 300 °C had uniform coverage on a transparent conductive oxide (TCO) after a subsequent high-temperature process. The ZnO layer was effective in preventing shunting through the CdS window layer so that the open-circuit voltage and fill factor of the CdTe solar cells were recovered and the short-circuit current was enhanced over that of the conventional CdTe solar cell. In the ZnO/CdS/CdTe configuration, the short-circuit current was further improved throughout the visible wavelength region by replacing the Cu-metal contact with a Cu solution contact. As a result the short-circuit current from 21.7 to 26.1 mA/cm² and the conversion efficiency of the CdTe solar cell increased from 12 to 15% without antireflective coating. Our result indicates that the Cu solution back contact is a critical factor for achieving a higher cell efficiency in addition to ZnO buffer layer.     

Influence of P<Superscript>+</Superscript>-ZnTe back surface contact on photovoltaic performance of ZnTe based solar cells

In order to improve photovoltaic performance of solar cells based on ZnTe thin films two device structures have been proposed and its photovoltaic parameters have been numerically simulated using Solar Cell Capacitance Simulator software. The first one is the ZnO/CdS/ZnTe conventional structure and the second one is the ZnO/CdS/ZnTe/P⁺-ZnTe structure with a P⁺-ZnTe layer inserted at the back surface of ZnTe active layer to produce a back surface field effect which could reduce back carrier recombination and thus increase the photovoltaic conversion efficiency of cells. The effect of ZnO, CdS and ZnTe layer thicknesses and the P⁺-ZnTe added layer and its thickness have been optimized for producing maximum working parameters such as: open-circuit voltage V_oc, short-circuit current density J_sc, fill factor FF, photovoltaic conversion efficiency η. The solar cell with ZnTe/P⁺-ZnTe junction showed remarkably higher conversion efficiency over the conventional solar cell based on ZnTe layer and the conversion efficiency of the ZnO/CdS/ZnTe/P⁺-ZnTe solar cell was found to be dependent on ZnTe and P⁺-ZnTe layer thicknesses. The optimization of ZnTe, CdS and ZnTe layers and the inserting of P⁺-ZnTe back surface layer results in an enhancement of the energy conversion efficiency since its maximum has increased from 10% for ZnO, CdS and ZnTe layer thicknesses of 0.05, 0.08 and 2 µm, respectively to 13.37% when ZnO, CdS, ZnTe and P⁺-ZnTe layer thicknesses are closed to 0.03, 0.03, 0.5 and 0.1 µm, respectively. Furthermore, the highest calculated output parameters have been J_sc?=?9.35 mA/cm², V_oc?=?1.81 V, η?=?13.37% and FF?=?79.05% achieved with ZnO, CdS, ZnTe, and P⁺-ZnTe layer thicknesses about 0.03, 0.03, 0.5 and 0.1 µm, respectively. Finally, the spectral response in the long-wavelength region for ZnO/CdS/ZnTe solar cells has decreased at the increase of back surface recombination velocity. However, it has exhibited a red shift and showed no dependence of back surface recombination velocity for ZnO/CdS/ZnTe/P?+?-ZnTe solar cells.     

Improvement of ZnO nanorod-based dye-sensitized solar cell efficiency by Al-doping

The current study investigates the performance of dye-sensitized solar cells (DSSCs) based on Al-doped and undoped ZnO nanorod arrays synthesized by a simple hydrothermal method. Current density-voltage (J-V) characterizations indicate that Al-doping in ZnO crystal structure can significantly improve current densities and the energy conversion efficiency (η) of ZnO nanorod-based DSSCs. The maximum η, 1.34%, was achieved in DSSC when Al-doped ZnO nanorod arrays were grown in 0.04 M zinc acetate dihydrate solution with 5 mM aluminum nitrate nonahydrate. This result represents a large increase of η in Al-doped ZnO nanorod-based DSSCs as compared to undoped (0.05%). The improved DSSC photovoltaic performance can be attributed to two main factors: (1) increased light harvesting efficiency due to a large amount of N719 adsorbed on the large surface area of Al-doped ZnO nanorod arrays, and (2) increased electrical conductivity due to A1³⁺ ion doped into the ZnO lattice at the divalent Zn²⁺ site, allowing electrons to move easily into the Al-doped ZnO conduction band.     

Performances of ZnO-Based Dye Sensitized Solar Cells Fabricated by Hydrothermal Synthesis and Sol-Gel Technique

ZnO is introduced as an alternative to TiO2 in dye sensitized solar cells （DSSCs） due to its band gap similar to TiO2, higher electron mobility, and flexible procedures of preparations. Several samples of ZnO films are prepared with the hydrothermal synthesis method and the sol-gel technique, respectively. These ZnO films were assembled as photoanodes in DSSCs using N3 dye as the sensitizer. The ZnO-based cells prepared by the hydrothermal synthesis show typical current source characteristics, whose fill factor （FF） is 0.44 and photo-to-electric power conversion efficiency is 0.34%. On the other hand, all the samples prepared with the sol-gel technique show accompanied source characteristics with relatively higher power conversion efficiencies （1%） but a lower FF （0.26）. X-ray diffraction （XRD） and atomic force microscopy （AFM） measurements indicate that the sol-gel samples have small particles sizes. Therefore, sol-gel samples could adsorb more dye molecules to generate high conversion efficiencies. At the same time, more grain boundaries make it more possible for injected electrons to recombine with the oxidized electrolyte. Hydrothermal samples have bigger grains, so they show poor conversion efficiency and relatively high FF.     

Improved performance of a crystalline silicon solar cell based on ZnO/PS anti-reflection coating layers

A porous silicon (PS) layer was prepared by photoelectrochemical etching (PECE), and a zinc oxide (ZnO) film was deposited on a PS layer using a radio frequency (RF) sputtering system. The surface morphology of the PS and ZnO/PS layers was characterised using scanning electron microscopy (SEM). Nano-pores were produced in the PS layer with an average diameter of 5.7 nm, which increased the porosity to 91%. X-ray diffraction (XRD) of the ZnO/PS layers shows that the ZnO film is highly oriented along the c-axis perpendicular to the PS layer. The average crystallite size of the PS and ZnO/PS layers are 17.06 and 17.94 nm, respectively. The photoluminescence (PL) emission spectra of the ZnO/PS layers present three emission peaks, two peaks located at 387.5 and 605 nm due to the ZnO nanocrystalline film and a third located at 637.5 nm due to nanocrystalline PS. Raman measurements of the ZnO/PS layers were performed at room temperature (RT) and indicate that a high-quality ZnO nanocrystalline film was formed. Optical reflectance for all the layers was obtained using an optical reflectometer. The lowest effective reflectance was obtained for the ZnO/PS layers. The fabrication of crystalline silicon (c-Si) solar cells based on the ZnO/PS anti-reflection coating (ARC) layers was performed. The I–V characteristics of the solar cells were studied under 100 mW/cm² illumination conditions. The ZnO/PS layers were found to be an excellent ARC and to exhibit exceptional light-trapping at wavelengths ranging from 400 to 1000 nm, which led to a high efficiency of the c-Si solar cell of 18.15%. The ZnO/PS ARC layers enhance and increase the efficiency of the c-Si solar cell. In this paper, the fabrication processes of the c-Si solar cell with ZnO/PS ARC layers are an attractive and promising technique to produce high-efficiency and low-cost of c-Si solar cells.     

Effect of Ultraviolet Light on Hybrid Zinc Oxide Polymer Bulk Heterojunction Solar Cells

Compared to conjugated polymer poly[2-methoxy-5-（3＇ ,7＇-dimethyloctyloxy）-l,4-phenylenevinylene] （MDMO-PPV） solar cells, bulk heterojunction solar cells composed of zinc oxide （ZnO） nanocrystals and MDMO-PPV have a better energy conversion efficiency. However, ultraviolet （UV） light deteriorates the performance of solar cells composed of ZnO and MDMO-PPV. We propose a model to explain the effect of UV illumination on these ZnO：MDMO-PPV solar cells. According to this model, the degradation from UV illumination is due to a decrease of exciton dissociation efficiency. Our model is based on the experimentM results such as the measurements of current density versus voltage, photoluminescence, and photocurrent.     

基于聚多巴胺/氧化锌复合阴极缓冲层的倒置聚合物太阳能电池的研究

利用多巴胺氧化自聚合形成聚多巴胺(PDA)与ZnO结合形成PDA/ZnO复合阴极缓冲层,制备了以P3HT:PC_(61)BM为活性层的倒置结构聚合物太阳能电池,通过改变PDA的自聚合时间来分析复合阴极缓冲层对器件性能的影响.实验发现,随着PDA的自聚合时间的增加,聚合物太阳能电池的光电转换效率先增大后减小,当自聚合时间为10 min时,相应器件光伏性能达到最优值,其开路电压V_(OC)为0.66 V,短路电流密度J_(SC)为9.70 mA/cm~2,填充因子FF为68.06%,光电转换效率PCE为4.35%.器件性能改善的原因是由于PDA/ZnO复合阴极缓冲层减小了ZnO与ITO之间的接触电阻,同时PDA中存在大量的氨基有利于倒置太阳能电池阴极对电子的收集.     

Highly crystalline bilayer electron transport layer for efficient conjugated polymer solar cells

Solution processed solar cells are a promising renewable energy technology due to the low fabrication costs. The most commonly used electron transport layer for solution processed organic solar cells is ZnO. However, sol-gel derived ZnO is amorphous, which limits interfacial charge transport. In this study, we demonstrate a ZnO bilayer, composed of a nanoparticle ZnO and sol-gel derived ZnO layer, as the electron transport layer in polymer solar cells incorporating the novel polymer poly [(5,6-difluoro-2,1,3-benzothiadiazol-4,7-diyl)-alt-(3,3‴-di (2-octyldodecyl)-2,2′; 5′,2″; 5″,2‴-quaterthiophen-5,5‴-diyl)] (PffBT4T-2OD). Compared with the single layer sol-gel ZnO, the bilayer displayed enhanced crystallinity. Consequently, the interfacial transport from the active layer was improved, as evidenced by dark J-V and PL spectroscopy measurements. Solar cells incorporating this bilayer ZnO layer achieved PCE values exceeding 10%, a relative improvement of 25% compared to the sol-gel ZnO devices.     

Nanostructured ZnO thin films by chemical bath deposition in basic aqueous ammonia solutions for photovoltaic applications

This paper presents further insights and observations of the chemical bath deposition (CBD) of ZnS thin films using an aqueous medium involving Zn-salt, ammonium sulfate, aqueous ammonia, and thioure. Results on physical and chemical properties of the grown layers as a function of ammonia concentration are reported. Physical and chemical properties were analyzed using scanning electron microscopy (SEM), X-ray energy dispersive (EDX), and X-ray diffraction (XRD). Rapid growth of nanostructured ZnO films on fluorine-doped SnO₂ (FTO) glass substrates was developed. ZnO films crystallized in a wurtzite hexagonal structure and with a very small quantity of Zn(OH)₂ and ZnS phases were obtained for the ammonia concentration ranging from 0.75 to 2.0 M. Flower-like and columnar nanostrucured ZnO films were deposited in two ammonia concentration ranges, respectively: one between 0.75 and 1.0 M and the other between 1.4 and 2.0 M. ZnS films were formed with a high ammonia concentration of 3.0 M. The formation mechanisms of ZnO, Zn(OH)₂, and ZnS phases were discussed in the CBD process. The developed technique can be used to directly and rapidly grow nanostructured ZnO film photoanodes. Annealed ZnO nanoflower and columnar nanoparticle films on FTO substrates were used as electrodes to fabricate the dye sensitized solar cells (DSSCs). The DSSC based on ZnO-nanoflower film showed an energy conversion efficiency of 0.84%, which is higher compared to that (0.45%) of the cell being constructed using a photoanode of columnar nanoparticle ZnO film. The results have demonstrated the potential applications of CBD nanostructured ZnO films for photovoltaic cells.     

Inverted organic solar cells comprising low-temperature-processed ZnO films

Inverted organic solar cells are fabricated using low-temperature-annealed ZnO film as an electron transport layer. Uniform ZnO films were prepared by spin coating a diethylzinc (DEZ) precursor solution in air, followed by annealing at 100 °C. Organic solar cells prepared on these ZnO films with a 1:1 P3HT:PCBM blend as the active layer show a high power conversion efficiency of 4.03 %, which is more than 10 % higher than the PCE of solar cells comprising ZnO prepared via a high-temperature sol–gel route.     

Preparation and characterization of ZnS/CdS bi-layer for CdTe solar cell application

In this work, bilayer ZnS/CdS film was prepared as an improved window layer of CdTe solar cell. TEM was used to observe the cross section of the bilayer structure. The total thickness of ZnS/CdS film was about 60 nm, which could allow more photons to pass through it and contribute to the photocurrent. Optical properties of the bilayers were investigated using UV–vis spectroscopy. Compared with poor transmission of standard CdS film in the short wavelength range of 350–550 nm, the transmission of ZnS/CdS was improved and reached above 50%. The ZnS/CdS was annealed with CdCl₂. X-ray photoelectron spectroscopy (XPS) was used to investigate its chemical properties. A possible diffusion between CdS and ZnS was observed after annealing. The efficiency of standard CdS/CdTe solar cell was 9.53%. The device based on ZnS/CdS window layer had a poor 6% efficiency. With annealing treatment on ZnS/CdS layer, the performance was improved and reached 10.3%. In addition, the homogeneity of solar cell performance was improved using ZnS/CdS window layer. A thin ZnS layer was quite effective to reduce the possible shunt paths and short parts of window layer and consequently contributed to fabrication of a homogeneous CdTe solar cell.     

Improving Cu2ZnSnS4 (CZTS) solar cell performance by an ultrathin ZnO intermediate layer between CZTS absorber and Mo back contact

The effects of an ultrathin ZnO intermediate layer deposited at the CZTS/Mo interface on CZTS solar cell performance have been investigated in this work. The ZnO layer inhibits the generation of MoS₂ layer and the formation of voids in the CZTS absorber. Consequently, the incorporation of this layer reduces the series resistance and increases the shunt resistance, which boosts photovoltaic conversion efficiency from 1.13% to 4.3%. (© 2014 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

One-pot synthesis of ferromagnetic Fe2.25W0.75O4 nanoparticles as a magnetically recyclable photocatalyst

ZnO nanostructures, including nanowires, nanorods, and nanoneedles, have been deposited on GaAs substrates by the two-step chemical bath synthesis. It was demonstrated that the O₂-plasma treatment of GaAs substrates prior to the sol?Cgel deposition of seed layers was essential to conformally grow the nanostructures instead of 2D ZnO bunches and grains on the seed layers. Via adjusting the growth time and concentration of precursors, nanostructures with different average diameter (26?C225?nm), length (0.98?C2.29???m), and density (1.9?C15.3?×?10⁹?cm^?2) can be obtained. To the best of our knowledge, this is the first demonstration of ZnO nanostructure arrays grown on GaAs substrates by the two-step chemical bath synthesis. As an anti-reflection layer on GaAs-based solar cells, the array of ZnO nanoneedles with an average diameter of 125?nm, a moderate length of 2.29???m, and the distribution density of 9.8?×?10⁹ cm^?2 has increased the power conversion efficiency from 7.3 to 12.2?%, corresponding to a 67?% improvement.