Surface morphology of GaN nanorods grown by catalyst-free hydride vapor phase epitaxy

GaN nanorods were grown on c-plane sapphire substrates by using catalyst-free hydride vapor phase epitaxy (HVPE). The effects of substrate temperature, Ga boat temperature, and Ga pretreatment on the surface morphology of GaN nanorods were investigated. From the dependence of a radial and axial growth rate on the substrate temperature, the kinetically limited process was found to be a rate determining step in the growth of GaN nanorods in HVPE. In addition, the activation energy of the growth along the both axial and radial directions were estimated. The dependence of a Ga boat temperature and the Ga pretreatment effect revealed that the density of nanorods were dependent on the flux of Ga species on the substrate.     

The role of strain in controlling the surface morphology of AlxGa1−xN following in situ treatment with SiH4 and NH3

Treatment of GaN with SiH₄ and NH₃ increases the size of surface pits associated with threading dislocations, allowing them to be easily imaged by atomic force microscopy. Here, we assess the effect of a similar treatment on Al_xGa_1−xN surfaces for x ≤ 0.4. For relaxed Al_xGa_1−xN epilayers, an increase in the observed size and density of threading dislocation pits is observed. However, if the Al_xGa_1−xN is under tensile strain, the treatment results in the appearance of nanometre-scale surface hillocks. These hillocks may prevent observation of the dislocation pits. The hillocks are found to consist of crystalline Al_xGa_1−xN, and hence are suggested to be formed by strain driven etching or transformation of the surface by SiH₄ and NH₃.     

Pulsed plasma ion source to create Si nanocrystals in SiO2 substrates

A pulsed KrF excimer laser of irradiance of about 10⁸ W/cm² was utilized to synthesize Si nanocrystals on SiO₂/Si substrates. The results were compared with that ones obtained by applying low bias voltage to Si(1 0 0) target in order to control the kinetic energy of plasma ions. Glancing incidence X-ray diffraction spectra indicate the presence of silicon crystalline phases, i.e. (1 1 1) and (2 2 0), on SiO₂/Si substrates. The average Si nanocrystal size was estimated to be about 45 nm by using the Debye-Scherrer formula. Scanning electron microscopy and atomic force microscopy images showed the presence of nanoparticles of different size and shape. Their distribution exhibits a maximum concentration at 49 nm and a fraction of 14% at 15 nm.     

Atomic layer deposition of PbZrO3 thin films

In this paper, we report on the preparation of lead zirconate films for the first time using atomic layer deposition in an attempt to investigate some of the film properties and also to evaluate possible use of the precursor combination to prepare more complex lead titanate zirconate. In the depositions tetraphenyl lead (Ph₄Pb) was used as the lead and zirconium 2,2,6,6-tetramethyl-3,5-heptadionato (Zr(thd)₄) as the zirconium precursor, while ozone was used as the oxygen source. Film growth, stoichiometry and quality were studied using different pulsing ratios at deposition temperatures of 275 and 300 °C. According to X-ray diffraction, the crystalline perovskite phase was observed when films deposited on SrTiO₃(1 0 0) were annealed at 600 °C. Surface roughness was reduced for lead deficient films as well as in annealed samples.     

The influence of Mn content on luminescence properties in Mn-doped ZnO films deposited by ultrasonic spray assisted chemical vapor deposition

Mn-doped ZnO (Zn_1−xMn_xO, 0 ≤ x ≤ 0.1) films are prepared by an ultrasonic spray assisted chemical vapor deposition method. X-ray diffraction and Raman scattering show that all the Zn_1−xMn_xO films are good wurtzite structures without any impurity phases. Cathodoluminescence spectra show that ultraviolet emission and green luminescence can be observed. The intensity of ultraviolet emission decreases with the increment of x, while the intensity of green luminescence increases with the increment of x when x ≤ 0.02. However, when x (x > 0.02) is further increased, the intensity of green luminescence decreases gradually, and the green luminescence disappears when x is above 0.075. We consider that the change of the luminescence is related to the competition between the radiative recombination and the non-radiative recombination.     

Characterization of free-standing GaN substrate grown through hydride vapor phase epitaxy with a TiN interlayer

Large-scale GaN free-standing substrate was obtained by hydride vapor phase epitaxy directly on sapphire with porous network interlayer. The bottom surface N-face and top surface Ga-face showed great difference in anti-etching and optical properties. The variation of optical and structure characteristics were also microscopically identified using spatially resolved cathodoluminescence and micro-Raman spectroscopy in cross-section of the GaN substrate. Three different regions were separated according to luminescent intensity along the film growth orientation. Some tapered inversion domains with high free carrier concentration of 5 × 10¹⁹ cm⁻³ protruded up to the surface forming the hexagonal pits. The dark region of upper layer showed good crystalline quality with narrow donor bound exciton peak and low free carrier concentration. Unlike the exponential dependence of the strain distribution, the free-standing GaN substrate revealed a gradual increase of the strain mainly within the near N-polar side region with a thickness of about 50 μm, then almost kept constant to the top surface.     

Epitaxial growth of Nd2Hf2O7(1 1 1) thin films on Ge(1 1 1) substrates by pulsed laser deposition

Nd₂Hf₂O₇ (NHO) thin films have been epitaxially grown by pulsed laser deposition (PLD) on Ge(1 1 1) substrates. In situ reflection high-energy electron diffraction (RHEED) evolution of the (1 1 1)-oriented NHO during the deposition has been investigated and shows that the epilayer has a twin-free character with type-B stacking. Interfacial structure of NHO/Ge has been examined by high-resolution transmission electron microscopy (HRTEM). The results indicate a highly crystalline film with a very thin interface, and the orientation relationship between NHO and Ge can be denoted as (1 1 1)_NHO//(1 1 1)_Ge and . Finally, twin-free epitaxial growth of NHO with type-B orientation displays temperature dependence and the type-B epitaxy is favored at high temperature.     

Influence of annealing atmosphere on ZnO thin films grown by MOCVD

ZnO films were deposited on c-plane sapphire substrates by metal-organic chemical vapor deposition (MOCVD). Annealing treatments for as-deposited samples were performed in different atmosphere under various pressures in the same chamber just after growth. The effect of annealing atmosphere on the electrical, structural, and optical properties of the deposited films has been investigated by means of X-ray diffraction (XRD), atomic force microscope (AFM), Hall effect, and optical absorption measurements. The results indicated that the electrical and structural properties of the films were highly influenced by annealing atmosphere, which was more pronounced for the films annealed in oxygen ambient. The most significant improvements for structural and electrical properties were obtained for the film annealed in oxygen under the pressure of 60 Pa. Under the optimum annealing condition, the lowest resistivity of 0.28 Ω cm and the highest mobility of 19.6 cm² v⁻¹ s⁻¹ were obtained. Meanwhile, the absorbance spectra turned steeper and the optical band gap red shifted back to the single-crystal value.     

Properties of ZnO thin films grown on Si substrates by photo-assisted MOCVD

ZnO thin films were grown on (1 0 0) p-Si substrates by Photo-assisted Metal Organic Chemical Vapor Deposition (PA-MOCVD) using diethylzinc (DEZn) and O₂ as source materials and tungsten-halogen lamp as a light source. The effects of tungsten-halogen lamp irradiation on the surface morphology, structural and optical properties of the deposited ZnO films have been investigated by means of atomic force microscope (AFM), X-ray diffraction and photoluminescence (PL) spectra measurements. Compared with the samples without irradiation, the several characteristics of ZnO films with irradiation are improved, including an improvement in the crystallinity of c-axis orientation, an increase in the grain size and an improvement in optical quality of ZnO films. These results indicated that light irradiation played an important role in the growth of ZnO films by PA-MOCVD.     

Epitaxial growth of Sc-doped ZnO films on Si by sol-gel route

The epitaxial growth of doped ZnO films is of great technological importance. Present paper reports a detailed investigation of Sc-doped ZnO films grown on (1 0 0) silicon p-type substrates. The films were deposited by sol-gel technique using zinc acetate dihydrate as precursor, 2-methoxyethanol as solvent and monoethanolamine (MEA) as a stabilizer. Scandium was introduced as dopant in the solution by taking 0.5 wt%¹ of scandium nitrate hexahydrate. The effect of annealing on structural and photoluminescence properties of nano-textured Sc-doped films was investigated in the temperature range of 300-550 °C. Structural investigations were carried out using X-ray diffraction, scanning electron microscopy and atomic force microscopy. X-ray diffraction study revealed that highly c-axis oriented films with full-width half maximum of 0.21° are obtained at an annealing temperature of 400 °C. The SEM images of ZnO:Sc films have revealed that coalescence of ZnO grains occurs due to annealing. Ostwald ripening was found to be the dominant mass transport mechanism in the coalescence process. A surface roughness of 4.7 nm and packing density of 0.93 were observed for the films annealed at 400 °C. Room temperature photoluminescence (PL) measurements of ZnO:Sc films annealed at 400 °C showed ultraviolet peak at about (382 nm) with FWHM of 141 meV, which are comparable to those found in high-quality ZnO films. The films annealed below or above 400 °C exhibited green emission as well. The presence of green emission has been correlated with the structural changes due to annealing. Reflection high energy electron diffraction pattern confirmed the nearly epitaxial growth of the films.     

Effects of sapphire substrate annealing on ZnO epitaxial films grown by MOCVD

The annealing effects of sapphire substrate on the quality of epitaxial ZnO films grown by metalorganic chemical vapor deposition (MOCVD) were studied. The atomic steps formed on (0 0 0 1) sapphire (α-Al₂O₃) substrate surface by annealing at high temperature was analyzed by atomic force microscopy (AFM). The annealing effects of sapphire substrate on the ZnO films were examined by X-ray diffraction (XRD), AFM and photoluminescence (PL) measurements. Experimental results indicate that the film quality is strongly affected by annealing treatment of the sapphire substrate surface. The optimum annealing temperature of sapphire substrates is given.     

Characterization of a thin CeO2-ZrO2-Y2O3 films electrochemical deposited on stainless steel

In this paper, we report for the first time formation of a thin CeO₂-ZrO₂-Y₂O₃ films electrodeposited on a stainless steel substrate. The samples have been characterized by X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and X-ray diffraction (XRD). The XRD and XPS data indicate formation of a solid solution and additional existence of Ce³⁺ states near the surface. After annealing, SEM examination has shown a microstructure formed by dispersed spherical agglomerates having a size between 20 and 60 nm.     

Synchrotron radiation assistant MOCVD deposition of ZnO films on Si substrate

The growth of ZnO film on Si(1 0 0) substrate has been studied with synchrotron radiation (SR) assisted MOCVD method. The diethylzinc (DEZn) and CO₂ are used as source materials, while Nitrogen is employed as a carrier gas for DEZn. With the assistance of SR the ZnO film can be deposited even at room temperature. XRD, SEM and photoluminescence (PL) studies show that the crystal quality of ZnO films grown with the assistance of SR is higher than that of those without SR assistance. The growth mechanism of ZnO film with the SR assistant MOCVD system is primarily discussed.     

Synthesis and characterization of nanostructured bimetallic films on α-Al2O3 substrates using electroless deposition

The Pt-Pd and Pd-Ag nanostructured bimetallic films on porous α-Al₂O₃ substrates are successfully synthesized by chemical deposition using lyotropic liquid crystalline templating strategy. The co-reduction of two metallic species in the presence of liquid crystalline phase by hydrazine hydrate produces hexagonal nanostructured Pt-Pd and lamellar nanostructured Pd-Ag films. Low-angle X-ray diffraction (XRD) and transmission electron microscopy (TEM) studies show the ordered nanostructure of both Pt-Pd and Pd-Ag films. The energy dispersive X-ray (EDX) and wide-angle XRD analyses of the bimetallic films have verified the coexistence and uniform distribution of constituent metallic species. By taking into account of catalytic activities, well-defined nanochannels and higher surface areas, the nanostructured bimetallic films might have application potential in microreactors.     

Photocatalytic property of TiO2 thin films sputtered-deposited on unheated substrates

TiO₂ films deposited on unheated substrates of alumina silicate glass by rf. (13.56 MHz) magnetron sputtering in the mixture of O₂ and Ar gases have been studied with X-ray diffraction (XRD), Atomic Force Microscopy (AFM) and optical spectroscopy. Structural and optical properties of TiO₂ films deposited at different O₂ concentrations and total pressures have been analyzed. Photocatalytic properties of TiO₂ films were characterized by following the degradation of methylene blue molecules under UV irradiation. It was found that the rate of methylene blue decomposition strongly depends on morphology and crystallinity of the deposited films, namely on the content of the anatase phase and on the size of the anatase grains. The best photocatalytic activity was found on TiO₂ films consisting of pure anatase phase with the size of grains of about 450 Å. With the help of those films a thin film reactor for water purification has been designed and tested.     

Effects of H2 ambient annealing in fully 0 0 2-textured ZnO:Ga thin films grown on glass substrates using RF magnetron co-sputter deposition

Gallium doped zinc oxide (ZnO:Ga) thin films were grown on glass substrates using RF magnetron co-sputtering, followed by H₂ ambient annealing at 623 K to explore a possibility of steady and low-cost process for fabricating transparent electrodes. While it was observed that the ZnO:Ga thin films were densely packed c-axis oriented self-textured structures, in the as-deposited state, the films contained Ga₂O₃ and ZnGa₂O₄ which had adverse effect on the electrical properties. On the other hand, post-annealing in H₂ ambient improved the electrical properties significantly via reduction of Ga₂O₃ and ZnGa₂O₄ to release elemental Ga which subsequently acted as substitutional dopant increasing the carrier concentration by two orders of magnitude. Transmittance of the ZnO:Ga thin films were all over 90% that of glass while the optical band gap varied in accordance with the carrier concentrations due to changes in Fermi level. Experimental observation in this study suggests that transparent conductive oxide (TCO) films based on Ga doped ZnO with good electrical and optical properties can be realized via simple low-cost process.     

Characteristic properties of Y2SiO5:Ce thin films grown with PLD

Three different gases (nitrogen (N₂), oxygen (O₂) and argon (Ar)) were used as background gases during the growth of pulsed laser deposition (PLD) Y₂SiO₅:Ce thin films. A Krypton fluoride laser (KrF), 248 nm was used for the PLD of the films on silicon (Si) (1 0 0) substrates. The effect of the background gases on the surface morphology, crystal growth and luminescent properties were investigated. All the experimental parameters, the gas pressure (455 mT), the substrate temperature (600 °C), the pulse frequency (8 Hz), the number of pulses (4000) and the laser fluence (1.6±0.2) J/cm² were kept constant. The only parameter that was changed during the deposition was the ambient gas species. The surface morphology and average particle sizes were monitored with scanning electron microscopy (SEM) and atomic force microscopy (AFM). X-ray diffraction (XRD) and Auger electron spectroscopy (AES) were used to determine the crystal structure and composition, respectively. Cathodo- (CL) and photoluminescence (PL) were used to measure the luminescent intensities for the different phosphor thin films. The nature of the particles, ablated on the substrate, is related to the collisions between the ejected particles and the ambient gas particles. The CL and PL intensities also depend on the particle sizes. A 144 h (coulomb dose of 1.4×10⁴ C cm⁻²) electron degradation study on the thin films ablated in the Ar gas environment resulted in a decrease in the main CL intensity peak at 440 nm and to the development of a new very broad luminescent peak spectra ranging from 400 to 850 nm due to the growth of a SiO₂ layer on the surface.     

Effects of substrate temperature on properties of NbNx films grown on Nb by pulsed laser deposition

NbN_x films were deposited on Nb substrate using pulsed laser deposition. The effects of substrate deposition temperature, from room temperature to 950 °C, on the preferred orientation, phase, and surface properties of NbN_x films were studied by X-ray diffraction, atomic force microscopy, and electron probe micro analyzer. We find that the substrate temperature is a critical factor in determining the phase of the NbN_x films. For a substrate temperature up to 450 °C the film showed poor crystalline quality. With temperature increase the film became textured and for a substrate temperature of 650−850 °C, mix of cubic δ-NbN and hexagonal phases (β-Nb₂N + δ′-NbN) were formed. Films with a mainly β-Nb₂N hexagonal phase were obtained at deposition temperature above 850 °C. The c/a ratio of β-Nb₂N hexagonal shows an increase with increased nitrogen content. The surface roughness of the NbN_x films increased as the temperature was raised from 450 to 850 °C.     

Alumina capped ZnO quantum dots multilayer grown by pulsed laser deposition

To extend the applicability of ZnO, with the bulk band gap of about 3.3 eV, into deep UV region, we have grown a multilayer of alumina capped ZnO quantum dots of mean in-plane sizes in the range of ∼1.8-3.6 nm at room temperature using alternate Pulsed Laser Deposition. Size dependent blue shift of the band gap of these dots up to ∼4.5 eV is observed in the optical absorbance spectra. The observed blue shift can be understood using the effective mass approximation in weak and strong confinement regimes.     

Characterization of ultra-fast deposited polycrystalline graphite by a CO2 laser-assisted combustion-flame method

High deposition rate, 750 μm/min, crystalline graphite was deposited on WC substrates by a CO₂ laser-assisted combustion-flame method at laser powers between 300 and 800 W. The structures, which were identified as pillars, were characterized by various methods. The pillars were cylindrical in shape and grew to a size of approximately 3 mm in length and in a few minutes. The laser power did not affect the overall length of the pillar, but caused changes in the physical shape. X-ray and electron diffraction results revealed the pillars to be crystalline graphite regardless of the laser power. Investigation of the pillars by scanning electron microscopy showed two distinct microstructural areas: an inner core of dense material surrounded by an outer shell of lamellar-like material. The core/shell microstructure was unaffected by the level of CO₂ laser power.