Preparation and photocatalytic activity of CeO2/TiO2 interface composite film

The CeO₂/TiO₂ and TiO₂/CeO₂ interface composite films were prepared on glass substrates by the sol-gel process via dip-coating and calcining technique. The scanning electron microscopy (SEM) revealed that the TiO₂ layer has a compact and uniformity glasslike surface with 200 nm in thickness, and the CeO₂ layer has a coarse surface with 240 nm in thickness. The X-ray diffractometer (XRD) analysis showed that the TiO₂ layer is made up of anatase phase, and the CeO₂ layer is structured by cubic fluorite phase. Through a series of photo-degradation experiments, the relationship of the photocatalytic activity with the constituents of the films was studied. In virtue of the efficient interfacial charge separation via the process of electron transfer from TiO₂ to CeO₂, the photocatalytic activity of the CeO₂/TiO₂ composite film is high. Contrarily, the photocatalytic activity of the TiO₂/CeO₂ composite film is low, due to its inert surface made up of CeO₂ with broad bandwidth. Apart from the effect of the film structure, the effect of film thickness on photocatalytic activity was also discussed.     

In vitro degradation of AZ31 magnesium alloy coated with nano TiO2 film by sol-gel method

A nano TiO₂ film was coated on AZ31 alloy substrate by sol-gel method. The TiO₂ film was characterized by X-ray diffractometry (XRD), differential scanning calorimetry-thermogravimetric analysis (DSC-TG), field emission scanning electron microscopy (FE-SEM) and energy dispersion spectroscopy (EDS). The degradation of the nano-TiO₂ coated alloy was evaluated by immersion test and electrochemical measurement. An attempt was made to relate corrosion of coated alloys with the annealing treatment and resultant structural evolution.     

Photo-catalytic H2 evolution over a series of Keggin-structure heteropoly blue sensitized Pt/TiO2 under visible light irradiation

We report the visible light-induced hydrogen generation over a series of Keggin-structure heteropoly blue (HPB) anions (PW₁₂O₄₀³⁻, phosphotungstic blue (PTB), GeW₁₂O₄₀⁴⁻ (GTB), SiW₁₂O₄₀⁴⁻ (STB), BW₁₂O₄₀⁵⁻ (BTB)) sensitized Pt/TiO₂ photo-catalysts. The sensitization of TiO₂ by HPB was certified using photo-electrochemical measurements and UV-vis absorption spectra. PTB showed the most pronounced sensitization effect for TiO₂ in those HPB anions and Pt/TiO₂-PTB showed the highest hydrogen generation activity. The sensitization of TiO₂ was significantly dependent on the reduction potential of HPA, which was determined by the kind of central atom in HPA.     

On the spray-drying deposition of TiO2 photocatalytic films

The photocatalytic activity of TiO₂ films deposited on different substrates by the spray-drying method using suspensions of commercially available TiO₂ (Degussa P25 or Tronox) as starting material was studied. The influence of the type of the initial TiO₂, preparation conditions (temperature of the substrate during the film deposition, temperature of the post-deposition annealing), substrate material (glass, fused silica, stainless steel and graphite), the presence of additives in the spraying suspension (polyethylene glycol, ethylene glycol and acetylacetone) and its sonication before spraying on the morphology, size of crystallites and phase composition (rutile/anatase ratio) was studied. Optimal conditions for spray deposition of the films are suggested.     

Optical characterization of PLD grown nitrogen-doped TiO2 thin films

Nitrogen-doped TiO₂ thin films were prepared by pulsed laser deposition (PLD) by ablating metallic Ti target with pulses of 248 nm wavelength in reactive atmospheres of O₂/N₂ gas mixtures. The layers were characterized by UV-VIS spectrophotometry and variable angle spectroscopic ellipsometry with complementary profilometry for measuring the thickness of the films. Band gap and extinction coefficient values are presented for films deposited at different substrate temperatures and for varied N₂ content of the gas mixture. The shown tendencies are correlated to nitrogen incorporation into the TiO_2-xN_x layers. It is shown that layers of significantly increased visible extinction coefficient with band gap energy as low as 2.89 eV can be obtained. A method is also presented how the spectroscopic ellipsometric data should be evaluated in order to result reliable band gap values.     

Low-temperature preparation of F-doped TiO2 film and its photocatalytic activity under solar light

A novel and simple method for preparing F-doped anatase TiO₂ (defined as FTO) film with high photocatalytic activity was developed using titanium-n-butoxide and NH₄F as TiO₂ and fluorine precursors under mild condition, i.e. low temperature (lower than 373 K) and ambient pressure. The prepared samples were characterized by XRD, SEM, X-ray photoelectron spectroscopy (XPS), diffuse reflectance spectrum (DRS), photoluminescence spectrum (PL) and TG-DSC analysis. The photocatalytic activity was evaluated by decomposing X-3B under artificial solar light. The results showed that the crystallinity of TiO₂ was improved by F-doping. F⁻ ions can prevent the grain growth, and the transformation of anatase to rutile phase was also inhibited. The doped fluorine atoms existed in two chemical forms, and the ones incorporated into TiO₂ lattice might take a positive role in photocatalysis. Compared with surface fluorination samples, FTO film exhibited better photocatalytic activity. The high photocatalytic activity of FTO may due to extrinsic absorption through the creation of oxygen vacancies rather than the excitation of the intrinsic absorption band of bulk TiO₂. Furthermore, the FTO can be recycled with little photocatalytic activity depression. Without any further treatment besides rinsing, after 6 recycle utilization, the photocatalytic activity of FTO film was still higher than 79%.     

Electrodeposition of nanostructured Pt films from lyotropic liquid crystalline phases on α-Al2O3 supported dense Pd membranes

Using the lyotropic liquid crystalline templating strategy, the nanostructured platinum film was electrochemically deposited on the α-Al₂O₃ supported dense palladium membrane. The XRD and TEM results of the Pt film revealed a hexagonal array of cylindrical pores with a uniform pore diameter of ca. 3.8 nm and a pore-to-pore separation of ca. 7.6 nm. The structure parameters of the Pt film were almost the same as those of the hexagonal liquid crystalline template. Based on SEM observations, the Pt film was featureless, smooth, and tightly adherent to the dense Pd membrane. The specific surface area of the Pt film, measured by using cyclic voltammetry, was ca. 13.8 m² g⁻¹, which was in accord with the theoretical value of 14.5 m² g⁻¹ for a perfect hexagonal nanostructure with the same structure parameters. By combining the dense Pd membrane for selective permeation to hydrogen with the Pt film of high specific surface area for catalysis, the as-synthesized two-layer film will be a promising catalytic membrane to intensify hydrogen-related reaction processes.     

Laser-induced voltage characteristics of Bi2Sr2Co2Oy thin films on LaAlO3 substrates

We report the laser-induced voltage (LIV) effects in c-axis oriented Bi₂Sr₂Co₂O_y thin films grown on (0 0 1) LaAlO₃ substrates with the title angle α of 0°, 3°, 5° and 10° by a simple chemical solution deposition method. A large open-circuit voltage with the sensitivity of 300 mV/mJ is observed for the film on 10° tilting LaAlO₃ under a 308 nm irradiation with the pulse duration of 25 ns. When the film surface is irradiated by a 355 nm pulsed laser of 25 ps duration, a fast response with the rise time of 700 ps and the full width at half maximum of 1.5 ns is achieved. In addition, the experimental results reveal that the amplitude of the voltage signal is approximately proportional to sin 2α and the signal polarity is reversed when the film is irradiated from the substrate side rather than the film side, which suggests the LIV effects in Bi₂Sr₂Co₂O_y thin films originate from the anisotropic Seebeck coefficient of this material.     

Fabrication and characterization of CuO-core/TiO2-shell one-dimensional nanostructures

We have fabricated CuO-core/TiO₂-shell one-dimensional nanostructures by coating the CuO nanowires with MOCVD-TiO₂. The structure of the core/shell nanowires has been investigated by using scanning electron microscopy, transmission electron microscopy, and X-ray diffraction analysis techniques. The CuO-cores and the TiO₂-shells of the as-synthesized nanowires have been found to have crystalline monoclinic CuO and crystalline tetragonal anatase TiO₂ structures, respectively. The CuO-core/TiO₂-shell nanowires are winding and has rougher surface, whereas the CuO nanowires are straight and have smoother surface.Influence of the substrate temperature and the growth time on the structure such as the morphology, size, and crystallographic orientation of CuO nanowires synthesized by thermal oxidation of Cu foils have also been investigated. All the nanowires have only the CuO phase synthesized at 600 °C, whereas those synthesized at 400 °C have both CuO and Cu₂O phases. The highest density of CuO nanowires with long thin straight morphologies can be obtained at 600 °C. In addition, the growth mechanism of the CuO nanowires has been discussed.     

A comparative study of the physical properties of Sb2S3 thin films treated with N2 AC plasma and thermal annealing in N2

As-deposited antimony sulfide thin films prepared by chemical bath deposition were treated with nitrogen AC plasma and thermal annealing in nitrogen atmosphere. The as-deposited, plasma treated, and thermally annealed antimony sulfide thin films have been characterized by X-ray diffraction (XRD), energy dispersive X-ray spectroscopy, scanning electron microscopy, atomic force microscopy, UV-vis spectroscopy, and electrical measurements. The results have shown that post-deposition treatments modify the crystalline structure, the morphology, and the optoelectronic properties of Sb₂S₃ thin films. X-ray diffraction studies showed that the crystallinity of the films was improved in both cases. Atomic force microscopy studies showed that the change in the film morphology depends on the post-deposition treatment used. Optical emission spectroscopy (OES) analysis revealed the plasma etching on the surface of the film, this fact was corroborated by the energy dispersive X-ray spectroscopy analysis. The optical band gap of the films (E_g) decreased after post-deposition treatments (from 2.36 to 1.75 eV) due to the improvement in the grain sizes. The electrical resistivity of the Sb₂S₃ thin films decreased from 10⁸ to 10⁶ Ω-cm after plasma treatments.     

Structural and morphological characterization of TiO2 nanostructured films grown by nanosecond pulsed laser deposition

TiO₂ has attracted a lot of attention due to its photocatalytic properties and its potential applications in environmental purification and self cleaning coatings, as well as for its high optical transmittance in the visible-IR spectral range, high chemical stability and mechanical resistance. In this paper, we report on the growth of TiO₂ nanocrystalline films on Si (1 0 0) substrates by pulsed laser deposition (PLD). Rutile sintered targets were irradiated by KrF excimer laser (λ = 248 nm, pulse duration ∼30 ns) in a controlled oxygen environment and at constant substrate temperature of 650 °C. The structural and morphological properties of the films have been studied for different deposition parameters, such as oxygen partial pressure (0.05-5 Pa) and laser fluence (2- 4 J/cm²). X-ray diffraction (XRD) shows the formation of both rutile and anatase phases; however, it is observed that the anatase phase is suppressed at the highest laser fluences. X-ray photoelectron spectroscopy (XPS) measurements were performed to determine the stoichiometry of the grown films. The surface morphology of the deposits, studied by scanning electron (SEM) and atomic force (AFM) microscopies, has revealed nanostructured films. The dimensions and density of the nanoparticles observed at the surface depend on the partial pressure of oxygen during growth. The smallest particles of about 40 nm diameter were obtained for the highest pressures of inlet gas.     

Fabrication and characterization of facing-target reactive sputtered polycrystalline TiO2 films

Polycrystalline TiO₂ films were fabricated using dc facing-target reactive sputtering at different sputtering pressures. The films deposited consist of pure anatase phase or a mixture of anatase and rutile and increasing rutile content to some extent deteriorates the crystallinity of the anatase. It was found that the plasma heating effect, which plays the role of substrate heating, is an important factor for the crystallinity of the films in the case of without substrate heating. The roughness of the films increases monotonically with the increase of the sputtering pressure, which can be ascribed to the decrease in the mobility of the impinging particles. UV-vis transmission measurements reveal that the pure anatase films have higher transmittance than those having mixed phases of anatase and rutile. The band gap value decreases from ∼3.35 to 3.29 eV owing to the increase in the fraction of rutile phase.     

c-Axis orientation control of YBa2Cu3O7−x films grown on inclined-substrate-deposited MgO-buffered metallic substrates

Biaxially textured YBa₂Cu₃O_7−x (YBCO) films were grown on non-textured metal substrates with inclined-substrate-deposited (ISD) MgO as template. The biaxial texture feature of the films was examined by X-ray pole-figure analysis, φ-scan, and 2θ-scan. A tilt angle of 32° of the MgO[001] with respect to the substrate normal was observed. Epitaxial growth of YBCO films with c-axis tilt angle of 32° with respect to the substrate normal was obtained on these substrates with SrTiO₃(STO) as buffer layer. Whereas, by choosing yttria-stabilized ZrO₂ and CeO₂ instead of STO as buffer layer, a c-axis untilted YBCO film was obtained. Higher values of T_c=91 K and J_c=5.5×10⁵ A/cm² were obtained on the c-axis untilted YBCO films with 0.46 μm thickness at 77 K in zero field. Comparative studies revealed a unique role of CeO₂ in controlling the orientation of the YBCO films grown on ISD-MgO buffered metal substrates.     

Fabrication and characterization of TS-1 films on α-Al2O3 substrates using TiCl3 as titanium source

The continuous and highly intergrown anatase-free TS-1 film was fabricated with TiCl₃ as the titanium source for the first time. The in situ nucleation and secondary growth method was employed to synthesize the TS-1 film. By means of scanning electron microscopy (SEM) images, X-ray diffraction (XRD) patterns, and FT-IR and UV-vis spectra measurements, the resulting film was observed to be anatase-free, continuous and highly intergrown with the MFI-type structure, and the Ti atoms existed only in tetrahedral coordination.     

Femtosecond Z-scan measurement of third-order optical nonlinearities in anatase TiO2 thin films

Anatase phase TiO₂ films have been grown on fused silica substrate by pulsed laser deposition technique at substrate temperature of 750 °C under the oxygen pressure of 5 Pa. From the transmission spectra, the optical band gap and linear refractive index of the TiO₂ films were determined. The third-order optical nonlinearities of the films were measured by Z-scan method using a femtosecond laser (50 fs) at the wavelength of 800 nm. The real and imaginary parts of third-order nonlinear susceptibility χ⁽³⁾ were determined to be −7.1 × 10⁻¹¹esu and −4.42 × 10⁻¹²esu, respectively. The figure of merit, T, defined by T=βλ/n₂, was calculated to be 0.8, which meets the requirement of all-optical switching devices. The results show that the anatase TiO₂ films have great potential applications for nonlinear optical devices.     

Structural and optical characterization of Ce-doped Gd2SiO5 films by sol-gel technique

Cerium-doped Gd₂SiO₅ (GSO:Ce) films have been prepared on (1 1 1) silicon substrates by the sol-gel technique. Annealing was performed in the temperature range from 400 to 1000 °C. X-ray diffraction (XRD), and atomic force microscopy (AFM) were used to investigate the structure and morphology of GSO:Ce films. Results showed that GSO:Ce film starts to crystallize at about 600 °C, GSO:Ce films have a preferential (0 2 1) orientation, as the annealing temperature increase, the (0 2 1) peak intensity increases, the full width of half maximum (FWHM) decreases, and the grain size of GSO:Ce films increases. Emission spectra of GSO:Ce films were measured, results exhibit the characteristic blue emission peak at 427 nm.     

Pulsed-laser crystallization and epitaxial growth of metal-organic films of Ca-doped LaMnO3 on STO and LSAT substrates

Ca-doped LaMnO₃ (LCMO) thin films have been successfully prepared on SrTiO₃ (STO) and [(LaAlO₃)_0.3-(SrAlTaO₆)_0.7] (LSAT) substrates using the excimer laser assisted metal-organic deposition (ELAMOD) process. The crystallization and the epitaxial growth of the amorphous metal-organic LCMO thin films have been achieved using a KrF excimer laser irradiation while the substrates were kept at constant temperature of 500 °C. Epitaxial films were obtained using laser fluence in the interval of 50-120 mJ/cm². The microstructure of the LCMO films was studied using cross-section transmission electron microscopy. High quality of LCMO films having smooth surfaces and sharp interfaces were obtained on both the STO and the LSAT substrates. The effect of the laser fluence on the temperature coefficient of resistance (TCR) was investigated. The largest values of TCR of the LCMO grown on the LSAT and the STO substrates of 8.3% K⁻¹ and 7.46% K⁻¹ were obtained at different laser fluence of 80 mJ/cm² and 70 mJ/cm², respectively.     

Preparation of poly-o-phenylenediamine/TiO2/fly-ash cenospheres and its photo-degradation property on antibiotics

A series of poly-o-phenylenediamine/TiO₂/fly-ash cenospheres(POPD/TiO₂/fly-ash cenospheres) composites have been prepared from o-phenylenediamine and TiO₂/fly-ash cenospheres under various polymerization conditions. The properties of the samples were characterized by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), specific surface area (BET), X-ray diffraction (XRD), Fourier transform infrared (FT-IR) and UV-vis diffuse reflectance spectrum (UV-vis DRS). Photocatalytic activity was studied by degradation of antibiotics waste water under visible light. The results indicate that the photo-induced method is viable for preparing modified photocatalysts, and the modified photocatalysts have good absorption in visible light range. The photocatalysts of POPD/TiO₂/fly-ash cenospheres which have good performance are prepared at pH 3 and 4, and the polymerized time around 40 min. When the photocatalysts are prepared under the conditions of pH 3 and polymerized time 40 min, the degradation rate of roxithromycin waste water could reach near 60%, and it indicates that the way of POPD modified TiO₂/fly-ash cenospheres to degrade the antibiotics waste water is viable.     

Synthesis of bamboo-leaf-shaped ZnO nanostructures by oxidation of Zn/SiO2 composite films deposited with radio frequency magnetron co-sputtering

Bamboo-leaf-shaped ZnO nanostructures were synthesized by oxidation of metal Zn/SiO₂ matrix composite thin films deposited on Si(1 1 1) substrates with radio frequency magnetron co-sputtering. The synthesized bamboo-leaf-shaped ZnO are single crystalline in nature with widths ranging from 30 to 60 nm and lengths of up to 5-10 μm, room temperature photoluminescence spectrum of the nanostructures shows a strong and sharp UV emission band at 372 nm and a weak and broad green emission band at about 520 nm which indicates relatively excellent crystallization and optical quality of the ZnO nanostructures synthesized by this novel method.     

Fabrication and characterization of Au/SiO2 nanocomposite films

Au/SiO₂ nanocomposite films were prepared by radio frequency sputtering technique and annealing. The above nanocomposite films were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), and atomic force microscopy (AFM). The surface of the nanocomposite films was uniform with the particle diameter of 100-300 nm. The size of Au crystallites increased on increasing annealing time. The luminescent behavior of the nanocomposite films was characterized by photoluminescence (PL) with different excitation wavelengths. Two emission peaks at around 525 nm and 560 nm were observed with the excitation wavelength at 325 nm. An intensive emission peak at around 325 nm was observed with the excitation wavelength at 250 nm, which is related to the defective structure of the amorphous SiO₂ layer because of oxygen deficiency, and could be applied to many fields, such as ultraviolet laser and ultraviolet detector.