Superheated water extraction of linear alquilbenzene sulfonates from sediments with on-line preconcentration/derivatization/detection

A fully automated screening method based on superheated water extraction of linear alquilbenzene sulfonates from sediments prior to preconcentration/derivatization/detection is presented. A multivariate optimization of both the extraction step and derivatization step was performed. Superheated water extraction was compared with conventional Soxhlet extraction obtaining better recoveries (>95% versus 80-86%) and a drastic reduction of the extraction time (50 min versus 24 h) by the proposed method. The on-line coupling of the extractor with a preconcentration/derivatization/detection manifold through a flow-injection interface has permitted to obtain a fully automated screening approach. Moreover, this research constitutes an environmentally friendly method due to the use of water as extractant instead of an organic solvent.     

Focused microwave-assisted Soxhlet extraction of acorn oil for determination of the fatty acid profile by GC–MS. Comparison with conventional and standard methods

A study of the feasibility of focused microwave-assisted Soxhlet extraction of acorn oil and comparison of results from analysis of trans fatty acids in the oil thus obtained with those for oils obtained by use of other methods commonly used for oil extraction are reported here. The proposed method was optimized by means of a 21-experiment screening design to determine, by means of a reduced number of experiments, which factors affect both extraction efficiency and the degree of unsaturation of the fatty acids in the oil. The proposed method enables total extraction of the fatty acids in 30 min, which is much less than the time required by the Folch (4.5 h), Soxhlet (16 h), and ISO (8 h) reference methods and the stirring–extraction method (56 h). The efficiency of extraction achieved by use of the proposed method is statistically equivalent to that achieved by use of the other methods; the composition of the extracts obtained by use of the proposed method and the Folch and stirring reference methods are also statistically similar. No trans fatty acids were present in the extracts obtained by use of the Folch, stirring, and proposed methods but they were detected in the extracts obtained by use of both the Soxhlet and ISO methods.     

Microwave-assisted extraction versus Soxhlet extraction in the analysis of 21 organochlorine pesticides in plants

A method to determine 21 organochlorine pesticides in vegetation samples using microwave-assisted extraction (MAE) is described and compared with Soxhlet extraction. Samples were extracted with hexane–acetone (1:1, v/v) and the extracts were cleaned using solid-phase extraction with Florisil and alumine as adsorbents. Pesticides were eluted with hexane–ethyl acetate (80:20, v/v) and determined by gas chromatography and electron-capture detection. Recoveries obtained (75.5–132.7% for Soxhlet extraction and 81.5–108.4% for MAE) show that both methods are suitable for the determination of chlorinated pesticides in vegetation samples. The method using microwave energy was applied to grass samples from parks of A Coruña (N.W. Spain) and to vegetation from the contaminated industrial area of Torneiros (Pontevedra, N.W. Spain).     

Determination of pyridine in soil and water samples of a polluted area

A method for the analyses of pyridine in environmental samples is described. For soil samples a distillation procedure followed by an extraction, an acidic extraction or a Soxhlet extraction can be used. For water samples a distillation procedure followed by extraction can be employed. Deuterated pyridine is used as an internal standard and the extracts are analyzed by GC-MS. The recoveries of the methods are higher than 80%; the detection limits for pyridine are 0.01 mg/kg for soil samples and 0.2 g/l for water samples.     

Determination of organochlorine pesticides and their metabolites in soil samples using headspace solid-phase microextraction

An analytical procedure was developed using headspace solid-phase microextraction (HS-SPME) for the determination of organochlorine pesticides (OCPs) and their metabolites in sandy soil samples. The developed procedures involving fiber selection, temperature effect, absorption time, soil matrix and the addition of solvents of different polarity were optimized. Also, the results were compared to those achieved using Soxhlet extraction standard method. The 100-microm polydimethylsiloxane (PDMS) and 65-microm PDMS-divinylbenzene showed good extraction efficiency for 18 organochlorine pesticides. An increase in the extraction efficiency of organochlorine pesticides and the metabolites was observed when the temperature increased, and an optimum temperature of 70 degrees C for extracting OCPs was obtained. The application of other hydrophilic solvents had different effects on the extraction of organochlorine pesticides and the metabolites. Higher responses of OCPs were obtained when 5 ml of water was added to the soil. Good linearity of OCPs between 0.2 and 4 ng/g soil was observed. The relative standard deviation was found to be lower than 25%. Also the limits of detection were between 0.06 and 0.65 ng/g, which were lower than those obtained using Soxhlet extraction. Moreover, the optimized HS-SPME procedure was applied to the analysis of OCPs in certified reference material (CRM) 804-050 soil and compared with Soxhlet extraction procedure. Results obtained in this study were in good agreement with those obtained using Soxhlet extraction. The mean values obtained using HS-SPME technique were in the range of 16.5 to 1459.6 mg/kg, which corresponds to the recoveries of 68% to 127% of the certified values of CRM soil.     

Improved Method for the Determination of Polychlorinated Dibenzo-p-dioxins and Dibenzofurans (PCDD/Fs) in Sanitary Napkins

Abstract

An improved method was developed for determining highly toxic 2,3,7,8-substituted polychlorinated dibenzo-p-dioxins and polychlorinated dibenzo-p-furans (PCDD/Fs) in sanitary napkins. Samples were extracted by Soxhlet (50% dichloromethane/hexane) and sonication (hexane), and a multi-layer silica column was used for clean-up after acetone precipitation to separate the superabsorbent polymers. Improved separation efficiency of PCDD/Fs from sanitary napkins with a high level of superabsorbent polymers was achieved using the acetone precipitation method. Hexane was then applied as an alternative solvent to remove residual interfering substances including sticky components contained on sanitary napkins via alumina column chromatography in the second clean-up step. Recoveries approached 100% with an average relative standard deviation of less than 15%, and recoveries of internal standards were from 70.5 to 114.8% and 0.6 to 13.6% for the two extraction methods. The mean method detection limit was 0.075–0.968?pg/g for Soxhlet extraction and 0.0032–0.091?pg/g for sonication extraction. The established method meets the quality criteria for the screening of dioxins stated in EU Regulations 589/2014 and 709/2014, and therefore provides a suitable alternative for the determination of dioxins in sanitary napkins containing superabsorbent polymers.     

Continuous microwave-assisted extraction coupled on-line with liquid-liquid extraction: determination of aliphatic hydrocarbons in soil and sediments

This paper describes a new extraction method for the determination of aliphatic hydrocarbons (AHs) in soil and sediment samples, using continuous microwave-assisted extraction (MAE) combined with liquid-liquid extraction, for clean-up purposes. Analytical determinations were carried out by gas chromatography coupled with impact ionization mass spectrometry. The influence of the experimental conditions was tested using an agricultural soil spiked with standards (stored at 4 degrees C for 1 month) as reference soil. Maximum extraction efficiencies (80-90%) were achieved using 0.1-1.0g of sample, 60microl of water and 3ml of n-hexane (extractant) and 5min of extraction time; less than 70% of the most volatile hydrocarbons (C(9)-C(12)) were recovered since many evaporated during the drying step of the sample. MAE was compared with a conventional extraction method such as Soxhlet and a good agreement in the results was obtained (average recovery percentage value of 105% by comparing MAE against Soxhlet). Quality parameters such as linear range (0.5-800microg/g), limits of detection (LODs) (0.1-0.2microg/g) and precision (RSD, 4-6%) were determined using spiked soil samples. This method was successfully applied to the analysis of aliphatic hydrocarbons (C(9)-C(27) including pristane and phytane) in contaminated real samples.     

Comparison of subcritical water and organic solvents for extracting kava lactones from kava root

Subcritical water extraction of lactones from a kava (Piper metlhysticum) root was compared to a Soxhlet extraction with water, to boiling in water, and to a sonication in acetone. For ground kava (250-500 microm), 2 h of subcritical water extraction were required for a complete extraction at 100 degrees C, while at 175 degrees C, 20 min were sufficient. For a complete extraction of the unground (shredded) kava, the time of extraction was extended to 40 min at 175 degrees C. Boiling for 2 h and extraction with Soxhlet apparatus for 6 h, both of which employed water at atmospheric pressure, produced yields 40-60% lower than those obtained with subcritical water. With unground kava, 40 min of subcritical water extraction yielded essentially the same recoveries of lactones as 18 h of sonication with acetone, methylene chloride, or methanol.     

Sequential Automated Focused Microwave-Assisted Soxhlet Extraction of Compounds with Different Polarity from Marine Sediments Prior to Gas Chromatography Mass Spectrometry Detection

An extraction method based on the use of a focused microwave-assisted Soxhlet extractor with subsequent gas chromatography separation and mass spectrometry detection is proposed for the analysis of environmental pollutants from marine sediments collected at the outflow of an urban wastewater treatment plant to the sea. For the extraction of compounds with different polarity, sequential extraction with dichloromethane and water was performed on each sample. The experimental variables were optimized by the experimental design methodology for both the organic and aqueous extractant. The total time required for quantitative extraction of triclosan, bisphenol A, estrone, estradiol, oxyfluorofen and permethrin was 75 min, a short time as compared with the 24 h Soxhlet extraction (diethylstilbestrol, 4-octylphenol, procymidone and 2,7/2,8-dichlorodibenzo-p-dioxin isomer pair).Revised: 10 March and 18 April 2005     

Simultaneous extraction and determination of anionic surfactants in waters and sediments

A new method has been developed for the simultaneous determination of the most frequently used anionic surfactants - linear alkylbenzene sulfonates (LAS), alkyl ethoxysulfates (AES) and alkyl sulfates (AS) - in aqueous and sediment samples. Preconcentration and purification of water samples are carried out by means of solid-phase extraction (SPE). The efficiency of two different extraction methods for the analysis of sediments - Soxhlet extraction and pressurized liquid extraction (PLE) - has been compared. Identification and quantification of the target compounds is performed using a liquid chromatography - mass spectrometry (LC-MS) system equipped with an electrospray interface (ESI) in negative ion-mode. Homologue recoveries are 85-123% for SPE, 94-112% for Soxhlet extraction and 81-125% for PLE in the case of LAS, and 60-94% for SPE, 61-109% for Soxhlet extraction and 55-99% for PLE in the case of AES, whereas the limits of detection are 0.1-0.5 ngml(-1) in water and 1-5 ngg(-1) in sediment. This method has been applied to the determination of anionic surfactants in the Guadalete estuary (SW Spain), and LAS concentration levels from 538 to 1014 ngg(-1) in sediments and from 25.1 to 64.4 ngml(-1) in waters have been found. AES values from 168 to 536 ngg(-1) in sediments and from 4.5 to 11.9 ngml(-1) in waters are reported for the first time in European rivers.     

New extraction method for the analysis of linear alkylbenzene sulfonates in marine organisms. Pressurized liquid extraction versus Soxhlet extraction

A new method has been developed for the determination of linear alkylbenzene sulfonates (LAS) from various marine organisms, and compared with Soxhlet extraction. The technique applied includes the use of pressurized liquid extraction (PLE) for the extraction stage, preconcentration of the samples, purification by solid-phase extraction (SPE) and analysis by liquid chromatography with fluorescence detection. The spiked concentrations were added to the samples (wet mass of the organisms: Solea senegalensis and Ruditapes semidecussatus), which were homogenized and agitated continuously for 25 h. The samples were extracted by pressurized hot solvent extraction using two different extraction temperatures (100 and 150 degrees C) and by traditional Soxhlet extraction. The best recoveries were obtained employing pressurized hot solvent extraction at 100 degrees C and varied in the range from 66.1 to 101.3% with a standard deviation of between 2 and 13. Detection limit was between 5 and 15 microg kg(-1) wet mass using HPLC-fluorescence detection. The analytical method developed in this paper has been applied for LAS determination in samples from a Flow-through exposure system with the objective of measuring the bioconcentration of this surfactant.     

Determination of 39 polybrominated diphenyl ether congeners in sediment samples using fast selective pressurized liquid extraction and purification

In order to reduce time of analysis, a new pressurized liquid extraction (PLE) method that automatically and rapidly achieves quantitative and selective extraction of 39 polybrominated diphenyl ether (PBDE) congeners in sediment samples was optimized. It consists of on-line cleanup by inclusion of sorbents in the extraction cell. The new method was compared with a conventional method based on the use of Soxhlet extraction followed by solid-phase extraction (SPE) with cartridges. The instrumental determination was performed by GC-MS, using negative chemical ionization in the selected-ion monitoring mode. Recoveries from 47 to 82% were obtained for spiked tri- to hepta-PBDE congeners in sediment sample. The repeatability of replicate extractions was better than 15% relative standard deviation. The detection limits obtained with the new developed method were between 1 and 46 pg/g dry weight. The reduction in the sample preparation (extraction + cleanup) time (from days to 30 min) with a similar efficiency than that afforded by the conventional Soxhlet extraction-SPE cleanup technique indicates the suitability of this method. The method was applied to sediment samples where the analytes were detected in the range of 0.86-2.49 ng/g dry mass.     

Isolation of flavonoids from aspen knotwood by pressurized hot water extraction and comparison with other extraction techniques

Pressurized hot water extraction (PHWE) conditions (time, temperature, pressure) were optimized for the extraction of naringenin and other major flavonoids (dihydrokaempferol, naringin) from knotwood of aspen. Extracts were analysed by GC-FID, GC-MS, HPLC-UV and HPLC-MS. The results were compared with those obtained by Soxhlet, ultrasonic extraction and reflux in methanol. Flavonoids were most efficiently extracted with PHWE at 150 °C and 220 bar with 35 min extraction time. Soxhlet with methanol gave slightly higher recoveries, but an extraction time of 48 h was required. Naringenin concentration was highest in knotwood (1.15% dry weight) and much lower in the sapwood. PHWE proved to be cheap, fast and effective for the isolation of biofunctional flavonoids from aspen knotwood, producing higher recoveries than 24 h Soxhlet extraction, sonication or 24 h reflux.     

Ultrasonication followed by single-drop microextraction combined with GC/MS for rapid determination of organochlorine pesticides from fish

A novel, rapid and simple sample pretreatment technique termed ultrasonication followed by single-drop micro-extraction (U-SDME) has been developed and combined with GC/MS for the determination of organochlorine pesticides (OCPs) in fish. In the present work, the lengthy procedures generally used in the conventional methods like, Soxhlet extraction, supercritical fluid extraction, pressurized liquid extraction and microwave assisted solvent extraction for extraction of OCPs from fish tissues are minimized by the use of two simple extraction procedures. Firstly, OCPs from fish were extracted in organic solvent with ultrasonication and then subsequently preconcentrated by single-drop micro-extraction (SDME). Extraction parameters of ultrasonication and SDME were optimized in spiked sample solution in order to obtain efficient extraction of OCPs from fish tissues. The calibration curves for OCPs were found to be linear between 10-1000 ng/g with correlation of estimations in the range 0.990-0.994. The recoveries obtained in blank fish tissues were ranged from 82.1 to 95.3%. The LOD and RSD for determination of OCPs in fish were 0.5 ng/g and 9.4-10.0%, respectively. The proposed method was applied for the determination of bioconcentration factor in fish after exposure to different concentrations of OCPs in cultured water. The present method avoids the co-extraction of lipids, long extraction steps (>12 h) and large amount of organic solvent for the separation of OCPs. The main advantages of the present method are rapid, selective, sensitive and low cost for the determination of OCPs in fish.     

Superheated water extraction, steam distillation and Soxhlet extraction of essential oils of Origanum onites

Superheated water extraction (SWE) at various temperatures (100, 125, 150 and 175°C), steam distillation, and Soxhlet extraction were compared in the extraction of essential oils from two samples of the plant Origanum onites, one cultivated, the other wild. C18 solid-phase extraction was used to elute the essential oils from the SWE aqueous extract. The compositions of the extracted essential oils obtained from all three methods were then characterized by comprehensive GC×GC/time-of-flight mass spectrometry (TOF/MS). The highest essential oil yields were obtained by using SWE at 150°C with a flow rate of 2 mL min^–1 and a pressure of 60 bar for 30 min: these were 3.76 and 4.11% for wild and cultivated O. onites samples, respectively, expressed as a percentage of 100 g of dry (leaf) matter. The yields obtained using SWE at 150°C were slightly higher than those from conventional methods. Steam distillation was performed for 3 h, and Soxhlet extraction was completed in 12 h. The major compounds found were borneol, terpinen-4-ol and carvacrol.     

Simultaneous determination of aliphatic and aromatic amines in water and sediment samples by ion-pair extraction and gas chromatography-mass spectrometry

A gas chromatography-mass spectrometry (GC-MS) method has been proposed for the determination of aliphatic and aromatic amines in a variety of environmental samples including wastewater, river water, sea water and sediment samples. The method includes ion-pair extraction with bis-2-ethylhexylphosphate (BEHPA), derivatisation of compounds with isobutyl chloroformate (IBCF) and their GC-MS analysis. Aliphatic and aromatic amines were isolated from aqueous samples using BEHPA as ion-pair reagent and derivatised with IBCF for their chromatographic analysis. Solid-liquid extraction of aliphatic and aromatic amines in sediment samples were performed in Soxhlet apparatus with acidic MeOH and ion-pair extraction with BEHPA were carried out for the isolation of amines followed by derivatisation with IBCF. Aliphatic and aromatic amines were then analysed with GC-MS in both electron impact (EI) and positive and negative ion chemical ionisation (PNICI) mode as their isobutyloxycarbonyl (isoBOC) derivatives. The obtained recoveries ranged from 81.0 to 98.0% and the precision of this method, as indicated by the relative standard deviations (RSDs) was within the range of 0.5 and 4.3%. The detection limits obtained from calculations by using GC-MS results based on S/N = 3 were within the range from 0.07 to 0.50 ng/l.     

Determination of fat in leather by the use of supercritical fluid extraction combined with on-line piezoelectric detection.

Leather samples were prepared and characterized as 'in house' matrix standards for the determination of fat. The Soxhlet standard method was used to establish the reference fat content in every standard sample. Sample homogeneity and stability were examined under specific storing conditions. The materials were subsequently used as matrix standards for the determination of fat in leather samples, using supercritical fluid extraction (SFE) with on-line piezoelectric detection. Real samples were weighed in the extraction SFE thimble, previously loaded with 1 g of diatomaceous earth. A temperature of 45 degrees C and a CO2 fluid density of 0.85 g ml-1 were used for extraction. The linear calibration range thus achieved was 0.001-0.040% m/m total fat (related to the weight of the leather) and the relative standard deviation +/- 3% (n = 11; P = 0.05). The results were compared with those obtained with the Soxhlet method and no significant differences were found.     

Modification of Soxhlet Extractor for Rapid and Effective Recovery of Phenolic Pollutants Adsorbed on XAD-4 Resin

A newly modified extractor facilitated rapid extraction (10.0 mL, 1 h) of eleven phenols from XAD-4 resin for comparable recoveries to those with conventional Soxhlet extractor (80.0 mL, 3 h). Combined with analysis by gas chromatography and gas chromatography-mass spectrometry in selected ion monitoring mode as tert-butyldimethylsilyl derivatives, the overall method was linear (≥ 0.9991) with satisfactory precision (≤ 9.2% RSD), accuracy (≤ 7.7% RE), detection limit (≤ 0.02 μg L^?1), and recovery rates (≥ 75.0%) in 0.05 to 1.0 μg L^?1. Six phenolic pollutants were quantitatively screened along with bisphenol A (0.028 μg L^?1) from river water.     

Gas chromatography/ion trap mass spectrometry applied for the determination of polybrominated diphenyl ethers in soil

A gas chromatography/ion trap mass spectrometry (GC/ITMS) method was developed for the determination of polybrominated diphenyl ethers (PBDEs). ITMS parameters were optimized in order to achieve the best sensitivity for the PBDE analysis. Tandem mass spectrometry, along with an isotope dilution internal standard method, was used for the quantitation. Chromatographic windows were developed for mono- to hepta-BDEs, depending on the retention times when a 30-m GC column was used. A different 15-m column was used to analyze deca-BDE. Environmental soil samples collected from an electronic waste recycling site were prepared by using Soxhlet extraction and column chromatographic cleanup. Average recoveries of 61-118% were obtained for the 13C-labeled PBDE internal standards spiked in the samples prior to sample preparation. The accuracy represented by relative analytical errors was -24% to 18%, and the precision (relative standard deviation) was 11-26% (n=8). The method detection limits ranged from 0.013-0.25 ng/g for the PBDEs in soil.     

The analysis of chlorinated dibenzofurans in municipal fly ash: Supercritical fluid extraction vs Soxhlet

A multiresidue supercritical fluid extraction procedure for chlorinated dibenzofurans (PCDFs) has been optimized as an efficient method for the determination of these compounds in fly ash samples. The results were compared with those obtained by Soxhlet extraction. Extracts from the two procedures were analyzed by gas chromatography–mass spectrometry (HRGC–MS) Statistical analysis of the results confirmed that supercritical fluid extraction provides data with a relative standard deviation of less than 10% while Soxhlet extraction data show a much greater spread.