超声协同TiO_2光催化脱除燃料油中有机硫的研究

采用溶胶凝胶法制备纳米TiO2光催化剂,引入超声作用,以空气中的氧气为氧化剂,正辛烷为模拟油品对燃料油中硫化物的脱除进行了研究。考察了光照强度、催化剂用量、反应时间、二苯并噻吩(DBT)初始浓度、超声功率等因素对TiO2光催化二苯并噻吩溶液降解效率的影响。结果表明,引入超声后DBT的降解率提高了10%左右,并在TiO2用量为2 g/L,通气量为800 mL/min,光照距离20 cm,DBT初始浓度为600 mg/L,反应时间为150 min,超声功率为500 W的条件下,DBT降解率达到了72.6%。     

光催化甲胺磷降解效率和降解机理的研究

本文以自制的纳米TiO2为光催化剂,研究了光催化条件(溶液pH值、催化剂浓度及甲胺磷浓度)对甲胺磷在水中降解率的影响。结果表明:通过优化催化条件,可以大大提高甲胺磷的降解率。在甲胺磷浓度为20 mg/L,反应液起始pH为10.00,催化剂用量为0.5 g/L,光照时间为3 h的条件下,甲胺磷的降解效率可达到71.8%。通过化学计算模拟了甲胺磷的分子构型,并结合离子色谱的检测结果初步探讨了甲胺磷光催化降解的反应机理。     

微波加热制备泡沫镍负载La3+掺杂纳米TiO2及其光催化降解甲醛的性能

 采用常规加热和微波加热方法制备了两种泡沫镍负载La3+掺杂的纳米TiO2光催化剂,以甲醛光催化降解为模型反应,考察了制备方法和掺杂La3+对催化剂催化性能的影响,并采用扫描电镜、透射电镜、 X射线衍射和能量分散式光谱分析对催化剂进行了表征. 结果表明,微波加热法制备的纳米TiO2具有典型的锐钛矿型晶体结构,其粒径均匀且明显小于常规加热法制备的催化剂. 泡沫镍负载1.5%La3+掺杂的TiO2的光催化性能得到明显改善,反应90 min后甲醛的降解率仍达到93%. 在实验中发现催化剂有失活现象,但经简单清洗后其活性能够恢复.     

超临界流体干燥法制备TiO2／C纳米粒子及光催化性能

以TiCl4为原料,采用溶胶凝胶法结合超临界流体干燥法(SCFD)制备了纳米级TiO2/C复合光催化剂.以苯酚的光催化降解对所得催化剂的催化活性进行了评价.结果表明,纳米TiO2/C复合粒子与单组分TiO2比较,复合粒子光催化活性高于单组分的TiO2,h苯酚降解率高达975 ％,COD为957%.并用XRD、TEM、 UV-Vis和XPS等手段进行了表征,iO2以锐钛矿型形式存在.比较了不同制备方法制得的TiO2/C复合催化剂,得出超临界干燥法制备的光催化剂具有粒径小,比表面积大,分散性好,光催化活性高等特点.     

活性炭负载纳米TiO2光催化降解性能研究

本文研究活性炭负载纳米TiO2的光催化降解性能和影响甲基橙废水处理的主要因素。结果表明:用溶胶-凝胶法制备的TiO2-活性炭催化剂具有比表面积大、分散性高、光催化降解性能好、可重复利用等优点;采用30W高硼紫外光灯,TiO2-活性炭光催化降解浓度为1500mg/L甲基橙废水的最优工艺条件是:催化剂活化温度为700℃、用量为1.0g/L、废水起始pH值为1、反应温度为45℃、光照时间为50m in。在此条件下,甲基橙和CODC r的去除率分别达99.8%和99.7%。     

掺硼纳米TiO2对农药毒死蜱的光催化降解作用

采用溶胶-凝胶法制备了掺杂硼的纳米TiO2,并用X射线衍射、红外光谱表征了产物的组成和结构.用制备好的掺硼纳米TiO2作为光催化剂对农药毒死蜱进行了光催化降解研究.结果表明:通过掺硼可以显著提高TiO2对毒死蜱的光催化效率.在硼掺杂量为3%,催化剂煅烧温度为500℃,煅烧时间为1 h,催化剂用量为15%时,毒死蜱的降解率最高.     

Au与Fe_3O_4纳米微粒共嵌TiO_2纳米纤维的制备及可见光催化性能

通过静电纺丝法制备出含有Fe3O4纳米微粒的TiO2纳米纤维,再采用浸渍还原法将Au纳米微粒嵌入到TiO2纳米纤维上,制备出一种具有较强磁性和良好可见光响应能力的复合光催化材料.采用X射线衍射仪(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)和紫外-可见固体漫反射光谱仪(UV-VisDRS)等对样品的结构和形貌进行表征,并以降解罗丹明B(RhB)为模型反应,考察了样品在可见光照射下的光催化性能.结果表明,嵌入Au纳米微粒可使复合纳米纤维在可见光下降解RhB时表现出非常好的降解速率和降解率;同时,将Fe3O4纳米微粒嵌入TiO2纳米纤维内部可以赋予材料较强的磁性,使材料便于分离和重复利用.     

超声波-二氧化钛光催化耦合法降解高效氯氰菊酯

采用超声波-TiO2光催化耦合法降解高效氯氰菊酯,考察了高效氯氰菊酯初始浓度、降解时间、溶液pH、催化剂用量等对高效氯氰菊酯农药残留的降解效果,并利用水果进行了实物模拟.结果表明:利用超声波-TiO2光催化耦合法能够有效地降解高效氯氰菊酯农药残留.在弱酸环境中,当纳米TiO2投放量为1.2g/L时,经2h超声催化降解,不同浓度的高效氯氰菊酯农药稀释液均被有效降解,降解率最高可达98.3%.     

乙酰丙酮金属配合物表面改性纳米二氧化钛

以乙酰丙酮稀土和乙酰丙酮铁配合物通过吸附法对纳米TiO2进行表面改性,以光催化降解甲基橙为探针反应,在紫外光照条件下考察了改性条件对纳米TiO2催化活性的影响,包括金属元素种类、配合物含量、吸附温度、溶剂用量、吸附时间等.研究表明,乙酰丙酮铁改性纳米TiO2最有效.当w[Fe(acac)3/TiO2]为0.25%,吸附温度为60℃,溶剂用量为乙醇/TiO2等于29 mL/g,吸附1.5 h时,改性后的纳米TiO2催化活性比改性前有了很大的提高.即使在普通白炽灯光照条件下,改性催化剂仍显示出很高的光催化活性,明显优于非改性的纯TiO2.改性纳米TiO2经过IR、XRD、UV-Vis、荧光、SEM-EDS和高倍光学显微镜等分析表征.     

Sn4+掺杂对TiO2纳米颗粒膜光催化降解苯酚活性的影响

金属离子掺杂能改善TiO2纳米微粒光催化活性,在光降解大气和水污染物的研究中,已引起人们的重视[1,2].实验证明,掺杂物的浓度、掺杂离子的分布、掺杂能级与TiO2能带匹配程度、掺杂离子d电子的组态、电荷的转移和复合等因素对催化剂的光催化活性有直接影响[3].Kamat等[4]曾利用TiO2颗粒与SnO2颗粒混合制膜,使光催化剂活性得到提高.但Sn4+掺杂TiO2用于光催化剂尚少见报道.本文采用等离子体化学气相沉积法(PECVD)[5]制备了Sn4+离子掺杂的TiO2纳米颗粒膜催化剂(TiO2-Sn),考察了其对苯酚的光催化降解活性,讨论了Sn4+离子的掺杂方式及光催化活性提高的机理.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

关于"对‘燃料电池物理及化学性能的有限时间热力学分析方法'的讨论”答复

把有限时间热力学理论用于化学过程的研究,将会得到一系列新的结论,开展这方面的研究是很有意义的.文献[1]以燃料电池为例,在同时考虑化学反应及传热不可逆性的情况下,研究了燃料电池的性能界限,文献[2]指出了文献[1]计算化学反应及传热不可逆性而引起系统与有关环境的总熵产生率的错误以及由此而导致的结论所存在的问题,并进行了富有启发性的分析与讨论.但文献[2]对于系统与有关环境的总熵产生率的计算也是不正确的,由此得到的其它结论自然不能成立.本文将就此情况下系统与有关环境的总熵产生率的计算再次进行讨论,并给出电池功率和效率的有限时间热力学性能界限.