Photodegradation of poly(methyl methacrylate)

The vacuum photodegradation at 30°C. of poly(methyl methacrylate) and copolymers with acrylaldehyde, methacrylaldehyde, and methyl acrylate has been studied. The polymers were examined in the form of expanded films as produced by a freeze-drying technique. At least one molecule of carbon monoxide is evolved for each chain scission. It is concluded that chain scission in poly(methyl methacrylate) is primarily the result of photoinduced aldehyde groups.     

Branching of anionic poly(methyl methacrylate)

A viscometric determination of the degree of branching γ, of poly(methyl methacrylate) obtained by anionic polymerization proved the reaction of the growing center of poly(methyl methacrylate) with the ester group of another polymer molecule, accompanied by the formation of a trifunctional branch point. This reaction occurs if the solution polymerization of methyl methacrylate is initiated: (1) with butyllithium at ?78°C only on attaining 100% conversion and after a long time or at +20°C immediately after the polymerization has set in; (2) with lithium tert-butoxide at +20°C after a long time. The degree of branching of poly(methyl methacrylates) obtained under similar conditions in the presence of tetrahydrofuran reaches higher values than for polymers prepared in toluene. The tacticity of polymers does not affect the experimentally determined γ values.     

Synthesis of poly(methyl methacrylate) macromonomer

Anionic polymerization of methyl methacrylate (MMA) was carried out in tetrahydrofuran (THF) or THF/toluene mixture at ?78°C initiated by triphenylmethyl sodium or lithium as initiators. Highly syndiotactic PMMA of low polydispersity (M _w/m _n = 1.11–1.17) could be prepared with triphenylmethyl lithium in THF or THF/toluene mixture at ? 78°C. Moreover, PMMA macromonomer having one vinylbenzyl group per polymer chain was prepared by the couplings of living PMMA initiated by triphenylmethyl lithium with p-chloromethyl styrene (CMS) at ?78°C. The coupling reaction of living PMMA initiated by triphenylmethyl sodium with CMS was scarcely occurred.     

Thermoluminescence of irradiated poly(methyl methacrylate)

Thermoluminescence of poly(methyl methacrylate) (PMMA) irradiated with x rays, has been studied in the temperature range 100 to 460°K. Two glow peaks with maxima at 136 and 368°K have been observed. These are analyzed by three methods and the results are compared. Both curves obey second order kinetics and correspond to activation energies of 0.17 and 0.88 eV, respectively. It is possible to identify the centers responsible for the two peaks by correlation with electron spin resonance and optical data obtained for the same samples irradiated under the same conditions. Spectral studies of the emission show that the low temperature peak has its maximum at 365 nm while the high temperature peak has its maximum at 480 nm.     

Dynamics of adsorbed poly(methyl acrylate) and poly(methyl methacrylate) on silica

Deuterium NMR and modulated differential scanning calorimetry (MDSC) were used to probe the behavior of ultrathin adsorbed poly(methyl acrylate) (PMA). The spectra for the bulk methyl-labeled PMA-d₃ were consistent with the motions of the polymer segments being spatially homogeneous. For the polymers adsorbed on silica, multicomponent line shapes were observed. The segmental mobility of the surface polymers increased with increased adsorbed amounts. In contrast to the behavior of the polymers in bulk, the adsorbed lower-molecular-mass PMA-d₃ was less mobile than the adsorbed high-molecular-mass polymer. The presence of a polymer overlayer was sufficient to suppress the enhanced mobility of the more-mobile segments of the adsorbed (inner) polymer. MDSC studies on adsorbed poly(methyl methacrylate) showed that the glass-transition temperature of the thin polymer films increased and broadened compared to the behavior of the polymer in bulk. The presence of a motional gradient with the less-mobile segments near the solid-polymer interface and the more-mobile segments near the polymer-air interface was consistent with the experimental observations.     

Methanol-induced opacity in poly (methyl methacrylate)

Methanol-induced opacity in poly (methyl methacrylate) (PMMA) is investigated subject to two cooling processes; furnace cooling and air cooling. The glass transition temperature of PMMA decreases with increasing time of exposure to methanol at 40–60°C and then increases during cooling, due to progressive desorption. Voids form during cooling as long as specimen temperature remains above its glass transition temperature. Since furnace cooling affords enough time for holes to expand larger than the light wavelengths, the transmittance of furnace-cooled PMMA is independent of wavelength. The transmittance of PMMA subjected to rapid cooling in the air is wavelength dependent due to scattering by holes smaller than light wavelengths. The transmittance of PMMA bearing a given weight gain of methanol (measured at absorption temperature) prior to cooling for furance cooling is lower than that for the same material subjected to air cooling. A sharp front between outer and inner regions is found in specimens removed quickly from the thermostated water bath to air at ambient temperature.     

Compatibilization of blends of polybutadiene and poly(methyl methacrylate) with poly(butadiene-block-methyl methacrylate)

Compatibilization of blends of polybutadiene and poly(methyl methacrylate) with butadiene-methyl methacrylate diblock copolymers has been investigated by transmission electron microscopy. When the diblock copolymers are added to the blends, the size of PB particles decreases and their size distribution gets narrower. In PB/PMMA7.6K blends with P(B-b-MMA)25.2K as a compatibilizer, most of micelles exist in the PMMA phase. However, using P(B-b-MMA)38K as a compatibilizer, the micellar aggregation exists in PB particles besides that existing in the PMMA phase. The core of a micelle in the PMMA phase is about 10 nm. In this article the influences of temperature and homo-PMMA molecular weight on compatibilization were also examined. At a high temperature PB particles in blends tend to agglomerate into bigger particles. When the molecular weight of PMMA is close to that of the corresponding block of the copolymer, the best compatibilization result would be achieved. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36 : 85–93, 1998     

Longitudinal volume viscosity of poly(methyl methacrylate)

Volume flow of poly(methyl methacrylate) (PMMA) (M?_n = 43,000 and T_g = 384) has been measured in an Instron Capillary Rheometer. Elastic modulus of the longitudinal wave, longitudinal volume viscosity, initial longitudinal volume viscosity, and retardation times are described at temperatures above T_g (418–483K) and compression rates of about 1.00–200.00 × 10⁵ s^?1. An initial increase followed by a decrease in longitudinal volume viscosity has been observed as the compression rate increases and the volume deformation decreases, this last behavior being at the lowest values of the compression rate (6.0 and 30.0 × 10^?5 s^?1) a typical nonequilibrium one. η_L also increases with increasing temperature (T_g decreases 0.18°C/MPa), and volume flow activation energy decreases as the volume deformation increases.     

Surface structure relaxation of poly(methyl methacrylate)

Surface structure relaxations caused by temperature changes at the free surface of poly(methyl methacrylate) were studied using IR-visible sum-frequency generation (SFG). A polarization-rotating technique was introduced to enhance the sensitivity of SFG for monitoring the surface structure relaxations during a cooling process. A new surface structure relaxation was observed at 67 degrees C. This temperature does not match any known structure relaxation temperatures for the bulk and is 40 degrees C below the bulk glass transition temperature. As expected for a free-surface phenomenon, the surface relaxation temperature was found to be independent of film thickness in the range of 0.1-0.5 microm.     

Thermal expansion of oriented poly(methyl methacrylate)

The thermal expansivities along (α∥) and perpendicular (α_⊥) to the draw direction of poly(methyl methacrylate) (PMMA) with extrusion draw ratios 1 ≤ λ ≤ 4 have been measured between 150 and 298 K. As λ was increased from 1 to 4, α∥ decreased 2–3 times, whereas α_⊥ increased only 20–35%. The orientation function f calculated from thermal expansivity using the aggregate model is found to change linearly with birefringence, indicating that each property provides a sensitive measure of molecular orientation. For PMMA, however, only thermal expansivity can give an absolute f, with results at 150 K in reasonable agreement with previous studies using other techniques. At higher temperature, i.e., above ambient, PMMA side-group motions are excited, expanding volume, and calculations based on the aggregate model may not be valid.     

Copolymerization reactivity of poly(methyl methacrylate) macromer

Poly(methyl mehtacrylate)(PMMA) macromers with several vinyl groups at both chain ends were synthesized by the mechanical scission reaction of the main chain in the presence of p-divinylbenzene(p-DVB). The radical copolymerization of this macromer with styrene(St) or MMA was carried out in benzene at 60°C and the reactivity ratio of both monomers (r₂) was calculated from a kinetic scheme of copolymerization. As a result, the effect of molecular weight and concentration of macromers was not observed in both copolymerization systems. The value of r₂, however, decreased as the number of end vinyl groups in a macromer (N) increased. These results are discussed in some detail as we describe the construction of the kinetic model of copolymerization.     

Radical polymerization of methyl methacrylate in the presence of isotactic poly(methyl methacrylate)

Methyl methacrylate (MMA) was polymerized by radical initiation at 25°C in DMF in the presence of preformed isotactic PMMA (iMA) with about 90% isotactic triads and different M?_v's, viz., iMA-1: 7.2 × 10⁵; iMA-2, 5.0 × 10⁵; iMA-3, 3.5 × 10⁵; iMA-4, 1.25 × 10⁵; and iMA-5, 1.15 × 10⁵. The MMA:iMA ratio was 6:1. The collected polymers were separated into two fractions by extraction with boiling acetone and characterized by 60 MHz NMR. It is found that the M?_v of the polymer formed ran parallel to the M?_v of iMA. In all cases syndiotactic PMMA (s-PMMA) was produced which associated with the isotactic substrate to form acetone-insoluble stereocomplexes. The syndiotactic polymers probably consist of long syndiotactic and heterotactic sequences. The syndiotacticity decreased with conversion and was generally highest in the presence of iMA-1. With iMA-1 even the formation of some additional i-PMMA (in the acetone-insolubles) was indicated, especially in the later stages of the polymerization. Characterization of the acetone-soluble fractions indicated that i,s-stereoblock polymers were also produced, of which the persistence ratios ρ increased with the M?_v of iMA. From these results it is concluded that this reaction differs from the conventional radical polymerization and can be considered a stereospecific replica polymerization, the driving force being the strong tendency of i- and s-PMMA to associate. The formation of i,s-stereoblock polymers and additional i-PMMA indicates that s-PMMA in its turn can also act as a polymer matrix.     

Radical polymerization of methyl methacrylate in the presence of low-molecular-weight poly(methyl methacrylate)

The kinetics of the bulk radical polymerization of methyl methacrylate and the structure and properties (physicomechanical and thermomechanical, as well as diffusion and sorption) of the polymers were examined in relation to the amount of low-molecular-weight poly(methyl methacrylate) added.     

Thermal degradation of phosphonated poly(methyl methacrylate)

On heating at volatilisation temperatures, poly(methyl methacrylate) (PMMA) and diethoxyphosphonated poly(methyl methacrylate) (Ph.PMMA) behave differently in the very early stage of the degradation process. The volatilisation rate of PMMA decreases slowly with conversion whereas Ph.PMMA polymers volatilise at a high initial rate which decreases quickly with conversion.The overall volatilisation rate of Ph.PMMA polymers in this stage is much lower than that of PMMA. This is attributed to the formation of anhydride in degrading Ph.PMMA by intramolecular cyclisation which forms high boiling chain fragments.     

Flow properties of poly(methyl methacrylate) solutions

Viscosity and normal stress behavior were measured for poly(methyl methacrylate) samples of various average molecular weights in diethyl phthalate solution at 30 and 60°C. All samples conformed approximately to the most probable distriution (M?_w/M?_n = 2). Concentrations ranged from 0.113 to 0.38 g/ml, and M?_w from 53,800 to 1,620,000. Despite considerable evidence in the literature of unusual linear viscoelastic behavior for this polymer, its nonlinear properties appear to be rather conventional. The viscosity–shear rate master curve was similar to that found earlier for concentrated solutions of polystyrene and poly(vinyl acetate) of comparable molecular-weight distribution. The viscosity time constant τ_o parallels τ_R, the characteristic time of the Rouse model, although the residual dependence of τ_o/τ_R on concentration and molecular weight appears to be slightly different from that for polystyrene and poly(vinyl acetate). Similar conclusions apply to the recoverable compliance J_e,^o estimated from the normal stress behavior of each solution, and its relationship to the Rouse model compliance J_R.     

Positron annihilation investigations on poly(methyl methacrylate)

Positron lifetime and Doppler broadened annihilation radiation were measured for seven different samples of poly(methyl methacrylate) at room temperature in vacuum. The polymerisation of methyl methacrylate was carried out as a bulk polymerisation in the presence of benzoyl peroxide as an initiator. The effect of the amount of the initiator on the viscosity-average molecular weight was studied. It was found that the viscosity-average molecular weight decreased with increasing amount of the initiator. The average lifetime and intensity of ortho-positronium (o-Ps) increased with increasing viscosity-average molecular weight up to 6.85 × 10⁴ and remained constant after that. The S-parameter showed a similar behaviour as that of the o-Ps intensity.     

Ethanol-induced crack healing in poly(methyl methacrylate)

The crack healing induced by ethanol in poly(methyl methacrylate) (PMMA) has been studied at temperatures of 40–60°C. Crack healing occurs because the effective glass transition temperature of PMMA is reduced to below the test temperature by ethanol plasticization. It is found that crack closure rate is constant at a given temperature. The fracture strength of healed PMMA is lower than that of the original samples. By comparing the fracture stress with the morphology of the crack edge on the PMMA surface, we found that a high degree of swelling is responsible for the incomplete recovery of mechanical strength. The fractography of the completely healed sample shows a very different fracture morphology from that of virgin PMMA. The transport of ethanol in PMMA also is studied. At lower temperatures, transport is described by ideal Case II behavior. As the temperature increases, the kinetics shift from ideal Case II to anomalous behavior. The first stage of crack healing is controlled by Case I transport. © 1994 John Wiley & Sons, Inc.     

Methyl methacrylate oligomerically-modified clay and its poly(methyl methacrylate) nanocomposites

A methyl methacrylate oligomerically-modified clay was used to prepare poly(methyl methacrylate) clay nanocomposites by melt blending and the effect of the clay loading level on the modified clay and corresponding nanocomposite was studied. These nanocomposites were characterized by X-ray diffraction, transmission electron microscopy, thermogravimetric analysis and cone calorimetry. The results show a mixed intercalated/delaminated morphology with good nanodispersion. The compatibility between the methylacrylate-subsituted clay and poly(methyl methacrylate) (PMMA) are greatly improved compared to other oligomerically-modified clays.     

Nanohole structure prepared by a polystyrene-block-poly(methyl methacrylate)/poly(methyl methacrylate) mixture film

Cylindrical nanoporous structures were prepared by using a mixture film of polystyrene-block-poly(methyl methacrylate) copolymer (PS-b-PMMA) and PMMA homopolymer (hPMMA), and they were analyzed by transmission electron microtomography (TEMT), X-ray reflectivity (XR), and grazing incidence small-angle X-ray scattering. For this purpose, the mixture film was spin-coated onto a silicon wafer modified by a neutral brush for PS and PMMA blocks, which generates PMMA cylindrical microdomains oriented normal to the substrate. Two methods were employed to prepare nanoporous structures: (1) all of the PMMA phase (PMMA block and PMMA homopolymer) in the film was removed by UV irradiation, followed by rinsing with a selective solvent (acetic acid) to PMMA and (2) only PMMA homopolymer was removed by selective solvent etching without UV irradiation. We found via TEMT and XR that the nanoporous structure in the film prepared by UV irradiation exhibited almost perfect cylindrical shape throughout the entire film thickness. However, when the film was rinsed with a selective solvent, nanoporous structures were not straight cylinders but had a funnel shape in which the diameter of nanopores located near the top of the film was larger than that located near the bottom of the film.