p-n 型GaInP2/GaAs叠层太阳电池研究

报道了对p-n型 GaInP2/GaAs叠层太阳电池的研究结果.采用低压金属有机物化学气相沉积工艺制备电池样品.通过对GaInP2顶电池中场助收集效应的计算机模拟，提出用p+p-n-n+结构取代常用的p+n 结构，显著改善了GaInP2顶电池和GaInP2/GaAs叠层太阳电池的光伏性能，使其光电转换效率(Eff)分别达到14.26% 和23.82% (AM0, 25℃, 2×2cm2). 关键词： 场助收集效应 镓铟磷 砷化镓 叠层太阳电池     

晶格失配对GaInP/In_xGa_(1-x)As/In_yGa_(1-y)As倒装三结太阳电池性能影响的分析

传统GaInP/(In)GaAs/Ge三结太阳电池因受其带隙组合的限制,转换效率再提升空间不大.倒装结构三结太阳电池因其更优的带隙组合期望可以得到更高的效率.基于细致平衡原理,结合P-N结形成机理,应用MATLAB语言对双晶格失配GaInP(1.90 eV)/In_xGa_(1-x)As/In_yGa_(1-y)As倒装结构三结太阳电池底、中电池的不同带隙组合进行模拟优化.模拟结果表明在AM1.5D,500倍聚光(500 suns)下,禁带宽度组合为1.90/1.38/0.94 eV的带隙最优,综合材料成本与试验条件,当顶、中电池最优厚度组合为4μm和3.2μm时理论转化效率高达51.22%,此时两个异质结的晶格失配度分别为0.17%和2.36%.忽略渐变缓冲层生长后底电池位错的影响,通过计算0.17%的晶格失配引入1.70×105cm~(-2)的插入位错密度,对比单晶格失配GaInP/GaAs/In_(0.32)Ga_(0.68)As(0.99 eV)倒装结构三结太阳电池光电转化效率仍提高了0.3%.     

空间用GaInP/GaAs/In0.3Ga0.7 As(1 eV)倒装三结太阳电池研制

采用阶变缓冲层技术 (step-graded) 外延生长了具有更优带隙组合的倒装GaInP/GaAs/In_0.3Ga_0.7As(1.0 eV) 三结太阳电池材料, TEM和HRXRD测试表明晶格失配度为2%的In_0.3Ga_0.7As 底电池具有较低的穿透位错密度和较高的晶体质量, 达到太阳电池的制备要求. 通过键合、剥离等工艺制备了太阳电池芯片. 面积为 10.922 cm² 的太阳电池芯片在空间光谱条件下转换效率达到32.64% (AM0, 25 ℃), 比传统晶格匹配的 GaInP/GaAs/Ge(0.67 eV) 三结太阳电池的转换效率提高3个百分点. 关键词： 太阳电池 三结 倒装结构     

GaInP/GaAs/Ge三结太阳电池的电子辐照损伤效应

研究了1 MeV和1.8 MeV电子辐照下GaInP/GaAs/Ge三结太阳电池的辐照损伤效应.电学性能研究结果表明,GaInP/GaAs/Ge三结太阳电池的开路电压、短路电流和最大功率随辐照剂量的增加发生明显衰降,在1 MeV电子辐照下剂量为1×10¹⁵cm^-2时,与辐照前相比最大功率衰降了17.7%.暗I-V特性分析表明,高能电子辐照下三结电池串、并联电阻的变化是引起太阳电池电学性能衰降的重要原因.光谱响应分析结果表明,GaInP 关键词： GaInP/GaAs/Ge太阳电池 电子辐照 电学性能 光谱响应     

直接键合的三结太阳能电池研究

本文研制了直接键合的三结GaInP/GaAs/InGaAsP太阳电池.直接键合技术可以减少晶格不匹配的材料在外延生长过程中产生的线位错和面缺陷,将缺陷限制在界面几十纳米的薄层而不向内扩散,是未来实现高效多结电池的发展趋势之一.此类电池国内鲜有报道.本文键合三结电池的键合界面采用p+GaAs/n+InP结构,得到电池开路电压3.0 V,在电池结构没有优化的情况下获得效率24%,表面未做减反膜.开路电压表明三结电池实现了串联,为单片集成的高效多结电池提供了新的途径.对实验结果进行了分析并给出了改进措施.     

GaInP2/GaAs/Ge叠层太阳电池材料的低压MOCVD外延生长

本文采用自制的LP-MOCVD设备,外延生长出GaInP₂/GaAs/Ge叠层太阳电池结构片,对电池材料进行了X射线衍射测试分析.另外,采用二次离子质谱仪测试了电池结构的剖面曲线.用此材料做出的叠层太阳电池,AMO条件下光电转换效率η=13.6%,开路电压V_oc=2230mV,短路电流密度J_sc=12.6mA/cm².     

单室沉积高效非晶硅/微晶硅叠层太阳电池的研究

采用甚高频等离子体增强化学气相沉积技术,在前期单室沉积的微晶硅薄膜太阳电池和非晶硅/微晶硅叠层太阳电池研究的基础上,通过对微晶硅底电池本征层硅烷浓度的优化,获得了初始效率达到11.02%(电池面积1.0 cm²)的非晶硅/微晶硅叠层太阳电池.同时,100 cm²的非晶硅/微晶硅叠层太阳电池的组件效率也达到了9.04%. 关键词： 非晶硅/微晶硅叠层电池 单室 甚高频     

提高非晶硅/微晶硅叠层太阳电池光稳定性的研究

如何提高硅基薄膜太阳电池的光稳定性是硅基薄膜太阳电池研究和产业化过程中非常重要的问题. 为了提高非晶硅/微晶硅叠层电池的光稳定性, 本文首先给出了良好光稳定性非晶硅顶电池的结果, 然后重点研究了N/P隧穿结和微晶硅底电池本征层硅烷浓度梯度对叠层电池光稳定性的影响. 经过初步优化, 连续光照1000 h后非晶硅/微晶硅叠层电池的最小光致衰退率只有7%.     

超薄高速率单结微晶硅薄膜电池及其叠层电池

采用甚高频等离子体增强化学气相沉积技术, 基于优化表面形貌及光电特性的溅射后腐蚀ZnO:Al衬底, 将通过调控工艺参数获得的器件质量级高速微晶硅(μupc-Si:H )材料(沉积速率达10.57 Å/s)应用到微晶硅单结电池中, 获得了初始效率达7.49%的高速率超薄微晶硅单结太阳电池(本征层厚度为1.1 μm). 并提出插入n型微晶硅和p型微晶硅的隧穿复合结, 实现了非晶硅顶电池和微晶硅底电池之间的低损电连接, 由此获得了初始效率高达12.03% (V_oc=1.48 eV, J_sc=11.67 mA/cm², FF=69.59%)的非晶硅/微晶硅超薄双结叠层电池(总厚度为1.48 μm), 为实现低成本生产太阳电池奠定了基础.     

空间用倒装三结太阳能电池及其抗辐射性能研究

使用金属有机化学气相沉积技术,在4英寸GaAs衬底上获得了空间用GaInP/GaAs/In_(0.3)Ga_(0.7)As倒装三结太阳能电池.高分辨X射线衍射和阴极射线发光测试结果表明AlInGaAs应力渐变缓冲层的晶格弛豫度约100%,其整面平均穿透位错密度约5.4×10~6/cm~2.与GaInP/InGaAs/Ge常规三结太阳能电池相比,在AM0光谱、25℃测试条件下,面积24 cm~2的倒装三结太阳能电池转换效率达到32%,输出功率提高了5%.采用1 MeV高能电子对倒装三结电池进行粒子辐照测试,电池各项性能参数随不同辐照剂量发生改变,在1×10~(15)/cm~2辐照总剂量下电池转换效率衰降比例达到15%.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.