非准确联合变换相关测量透镜焦距

提出了一种利用非准确联合变换相关测量透镜焦距的方法.该方法首先利用已知焦距透镜记录联合功率谱,再用记录的联合功率谱经被测焦距透镜输出相关点,记录相关点并测出其间距,可以计算出被测透镜的焦距.理论分析和实验结果表明,该方法有较高的测量准确度,能实现透镜焦距的自动测量.     

二极管端面抽运的固体激光放大器自身热透镜焦距测量

通过分析激光经过热透镜后光束半径的变化，提出了利用放大器测量热透镜焦距的方法.根据激光束传输与变换理论，得到了热透镜焦距的表达式，并分析了其前提条件和近似偏差.最后，基于上述理论分析，测量了激光二极管端面抽运Tm,Ho∶GdVO₄放大器的热透镜焦距. 关键词： 热透镜焦距 固体激光 激光束传输与变换     

基于哈特曼-夏克波前测量原理的焦距测量

本文从哈特曼-夏克波前测量原理出发,提出了基于波前测量的透镜焦距测量方法|得到了使用这一方法测量焦距的计算公式.使用633 nm和780 nm两种波长的半导体准直激光器作为光源,测量了三片双合透镜的焦距,结果表明,633 nm光源下测量得到的波长与透镜的设计焦距值相吻合,能够正确测量透镜焦距|而780 nm光源的测量结果显示出较大的相对测量偏差,但可用于评估透镜的剩余球差、色差以及制造公差.     

基于哈特曼-夏克波前测量原理的焦距测量

本文从哈特曼-夏克波前测量原理出发,提出了基于波前测量的透镜焦距测量方法;得到了使用这一方法测量焦距的计算公式.使用633 nm和780 nm两种波长的半导体准直激光器作为光源,测量了三片双合透镜的焦距,结果表明,633 nm光源下测量得到的波长与透镜的设计焦距值相吻合,能够正确测量透镜焦距;而780 nm光源的测量结...     

干涉条纹法测量LD端面泵浦Nd∶YAG热透镜焦距

研究了端面泵浦Nd∶YAG晶体热透镜效应,提出了一种新的测量热透镜的方法-干涉条纹法,并通过理论估算与用此方法所测的热透镜焦距相比较, 表明此方法所测热透镜焦距随着泵浦光功率的增大二者越来越吻合, 验证了该方法的可靠性. 该方法解决了端泵Nd∶YAG时, 由温度梯度, 热应力双折射和端面形变所引起的总的热透镜焦距难以测量的问题.     

小口径长焦透镜的焦距检测技术

基于朗奇-泰伯效应及莫尔条纹技术,利用发散光和不等周期光栅的焦距测量方法被用于小口径长焦透镜的焦距测量。将一块曲率半径存在加工误差的平凹长焦透镜作为待测透镜进行焦距测量。在未知透镜真实曲率半径的情况下,首先计算待测透镜曲率半径误差对焦距检测精度的影响,并确定透镜在整个检测系统中的位置,然后进行透镜焦距实际测量,分别计算多组测量焦距值。通过对比发现,在未知待测透镜曲率半径的情况下,检测焦距的重复性、稳定性均一致,所测焦距均为33200～33270mm,且重复性精度高于±0.055%,测量精度优于焦深的1/5。结果充分说明,所提方法对小口径长焦透镜的焦距检测是可靠、有效的。     

干涉条纹法测量LD端面泵浦Nd∶YAG热透镜焦距

研究了端面泵浦Nd∶YAG晶体热透镜效应,提出了一种新的测量热透镜的方法 干涉条纹法,并通过理论估算与用此方法所测的热透镜焦距相比较,表明此方法所测热透镜焦距随着泵浦光功率的增大二者越来越吻合,验证了该方法的可靠性 该方法解决了端泵Nd∶YAG时,由温度梯度,热应力双折射和端面形变所引起的总的热透镜焦距难以测量的问题.     

基于Talbot-Moiré法的长焦透镜焦距测量的极限精度分析

长焦距测量的Talbot-Moiré法是研究热点,目前很多方法虽然都是基于Talbot现象和Moiré技术,但基本原理和实验方案各不相同,因此焦距计算公式也不相同。基于透镜位相变换作用,利用Talbot效应和Moiré条纹,通过图像处理的方法获得条纹的斜率变化,根据焦距与莫尔条纹斜率之间的关系求得透镜焦距。由于长焦透镜的焦距相对于被测透镜厚度大得多,完全可以看作是薄透镜对光束的变换,可用薄透镜对球面波的变换作用来近似表示其对高斯光束的变换。因此,该方法测量长焦透镜焦距对于高斯光束与非高斯光束焦距测量结果无差别,均适用。最后全面分析了该测量方法的误差及精度极限。在影响测量精度的各个误差因素中,光栅节距误差对焦距测量的影响最为显著。     

全息透镜的焦距测量

本文首先给出了全息透镜像散成像的焦距公式,介绍了用全息光栅法测量全息透镜焦距的原理,对两块自制的全息透镜在原光路再现情况下测量了其焦距,并用另一种参数测量方法对测量结果进行了验证,两者基本相符。通过分别测量全息透镜两个焦距,从而可得出其像散大小。最后指出了使用这种方法应注意的问题。     

基于菲涅耳声透镜的声速与焦距的测量实验

将"空气中声速测量"实验和"薄透镜焦距测量"实验融合,设计了集声学原理和光学原理的"菲涅耳声透镜"实验,明确了该实验所使用的实验仪器,给出了实验内容,即测量声透镜的焦距、通过测量声透镜的几何参量得出超声波的波长、测量超声波在空气中的声速.最后,制作了焦距f为50mm的声透镜,并对实验内容进行了可行性分析及实验验证.实验结果(声透镜的焦距为50.3mm及超声波波长值8.70mm)与理论设计值基本一致.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.