Use of paper capsules for cadmium determination in biological samples by solid sampling flame atomic absorption spectrometry

In this study, a new device was applied for direct solid sampling flame atomic absorption spectrometry. It was used for trace determination of cadmium in biological samples (bovine and chicken liver). Test samples (0.5 to 7 mg) were weighed into small paper capsules, which were introduced into a quartz cell heated by an air-acetylene flame. Operational conditions for the proposed system were evaluated. There was no significant difference between the results obtained with the proposed system and those obtained after digestion and determination by conventional graphite furnace atomic absorption spectrometry. Good agreement was also obtained with the certified values of two reference materials. Background signals were always low. The characteristic mass was 0.34 ng and relative standard deviation was less than 8%. The limit of detection for the proposed procedure was 1.6 ng or 0.23 μg g^− 1 if a sample mass of 7 mg was used. Excluding the steps for sample preparation (drying, milling and weighing), the proposed system allows the determination of 40 test samples per hour and it can be easily adapted to conventional flame atomic absorption spectrometers.     

Cumulative neutron activation of short-lived radionuclides for the analysis of large samples in mineral exploration

Cumulative neutron activation is used to determine mg/kg concentrations of gold in rock samples, weighing 10 g. Twenty 0.5 g replicates are irradiated in an epithermal-neutron flux for 5 s and counted for 14 s. The twenty spectra are summed, and gold is measured with the 279 keV gamma-ray of^197mAu (7.2 s). Total analysis time for a 10 g sample is 400 s and detection limits around 2 mg/kg are achieved in gold ores, sulfides and silicates.     

A method for the determination of Mn,Cu, Zn,K and Na in small tissue biopsies by neutron activation analysis

A method has been worked out for the determination of Mn, Cu, Zn, K and Na in tissue biopsies weighing between 10 and 50 mg. The samples were dried, packed in polyethylene containers and irradiated at a flux of 1.8·10¹² n·cm⁻²·sec⁻¹ for 48 hrs. They were dissolved and separated into five fractions by ion exchange chromatography. Managenese was precipitated and counted as MnO₂ and zinc as quinaldate. Copper and potassium were counted in solution. Sodium was taken up in hydrated antimony pentoxide (HAP) and counted in that stage. Accuracy, precision and specificity were determined by recovery experiments and by analysis ofBowen's biological standard.     

Determination of 137Cs in Soil Samples by Low-Level Compton Suppression Gamma-Counting

We have used Compton suppression gamma ray counting to effectively measure ¹³⁷Cs in undisturbed environmental samples weighing only one hundred grams of material. Our results have shown that Compton suppression is ideal in determining low levels (1–3 Bq/kg) of ¹³⁷Cs in soil samples, while the Compton advantage is negligible for higher concentrations. Quality assurance and quality control experiments show that for samples weighing 100–200 grams, gamma-ray attenuation is significant (up to 10% difference) when analyzing different soil compositions.     

Solid—liquid phase diagrams of mixtures containing substituted phenols and amine mixtures

The thermal decomposition of CaCO₃ was studied under high vacuum by means of both TG and the more recently developed constant decomposition rate thermal analysis (CRTA) which allows the monitoring of both reaction rate and the residual pressure over the sample. The reliability of the kinetic results seems to be much higher with the latter technique which actually allows the reduction of the reaction rate and therefore the heat and mass transfer effects over a broad range of sample size. For instance, it was necessary, by conventional TG started under a vacuum of 2 10^?6 torr with a heating rate of 0.5 K min^?1, to lower the amount of sample to 2 mg in order to obtain the same activation energy as that calculated from CRTA with various samples weighing up to 50 mg. The TG experimental conditions quoted above (and which are upper limits of mass and heating rate) are beyond the limit of sensitivity of most available conventional TG equipment.     

Feasibility of using direct determination of cadmium and lead in fresh meat by electrothermal atomic absorption spectrometry for screening purposes

A method for the direct determination of cadmium and lead in fresh meat for screening purposes is proposed using electrothermal atomic absorption spectrometry. The fresh meat samples were homogenized, weighed directly onto solid sampling platforms and introduced into a transversely heated solid sampling graphite tube. The main challenges associated with this procedure, such as weighing errors and optimization of the temperature program were investigated in detail. Calibration was performed against aqueous standards and two modifiers were investigated: 0.05% Pd + 0.03% Mg + 0.05% Triton X-100 and 0.01% Pd + 10% NH₄NO₃ + 0.05% Triton X-100. The former one is recommended due to the higher pyrolysis temperature obtained for cadmium and the better limits of detection of 1.9 μg kg^− 1 for lead and 0.13 μg kg^− 1 for cadmium, based on 10 mg of sample mass. The results obtained for cadmium and lead in two certified reference materials were statistically not different from the certified values on a 95% confidence level, indicating that calibration against aqueous standards is suitable for this application. In order to evaluate weighing errors the fresh samples were dried (at 60 °C) to constant weight; the results obtained with fresh and dried samples were in agreement, taking the loss of weight into consideration for the latter ones. The average relative standard deviation of 14% is in concordance with the results of others using fresh meat. Comparison with the digestion method adopted by the Brazilian Ministry of Agriculture shows no significant differences between the results at the 95% confidence level. This study shows that direct analysis of fresh meet can be applied as a rapid routine screening procedure for residue control in products of animal origin, helping the implementation and maintenance of sanitary control.     

Chromatographic assay of carbonates in the submilligram range: Application to carbonate assay of calcified tissue

Analytical assay methods for carbonate ions in calcified tissues generally lack the sensitivity and accuracy required to assay samples weighing less than 1 mg. The authors present a technique based on acid attack of the sample and recovery of the released carbon dioxide which is then analyzed by gas chromatography. The most favorable working conditions are established in an experimental study of the main factors likely to improve the performance: the authors study the Chromatographic parameters, the grain-size of the powered sample, the reaction temperature and pressure, the viscosity of the medium, and the influence of the acid concentration.This new process can be applied, with no major experimental difficulties, to samples weighing no more than 1 mg and containing 10 μg and above of carbonate ions; the detection limit is under 10 μg. The assay, which takes about 10 min, gives reproducible results with a variation coefficient of 5.2% or less.     

Electrochemical Determination of Sunscreens Agents in Cosmetic Using Square Wave Voltammetry

Sunscreen agents and in particular UV filters are compounds added in different cosmetic formulations, that has the function of preventing damage caused by sun exposition. Therefore, this paper proposes the development of a simple, fast and reliable electroanalytical method utilizing square wave voltammetry (SWV) to the determination of Benzophenone‐3 (BZ‐3), camphor 4‐methylbenzylidene (MBC) and 2‐ethylhexyl‐4‐methoxycinnamate (OMC) in cosmetic samples. The electrochemical system consisted of a cell with three electrodes: work – gold electrode modified, reference – Ag/AgCl_(sat) and auxiliary – platinum, using as supporting electrolyte 4.0 mL of Britton Robinson Buffer 0.04 mol L^?1 (pH=4.0), 1.0 mL of methanol and 5.50×10^?4 mol L^?1 of cetyltrimethylammonium bromide (CTAB). The method was validated using three commercial sunscreen samples and the results showed recovery values between 83 and 98 %. The average values found for the analysed samples were 3.49 % m/m (728 mg L^?1) to BZ‐3, 0.56 % m/m (113 mg L^?1) to MBC and 0.99 % m/m (208 mg L^?1) to OMC. The detection (DL) and quantification (QL) limits were 0.47 mg L^?1 and 1.56 mg L^?1 to BZ‐3, 0.77 mg L^?1 and 2.58 mg L^?1 to MBC and 0.78 mg L^?1 and 2.59 mg L^?1 to OMC, respectively. The sunscreen protector samples were also evaluated by high‐performance liquid chromatography (HPLC) demonstrating a good correlation between the results and compared the results with allowed concentration.     

Determination of arsenic compounds in marine mammals with high-performance liquid chromatography and an inductively coupled plasma mass spectrometer as element-specific detector

Total arsenic concentrations and the concentrations of individual arsenic compounds were determined in liver samples of pinnipeds [nine ringed seals (Phoca hispida), one bearded seal (Erginathus barbatus)] and cetaceans [two pilot whales (Globicephalus melas), one beluga whale (Deliphinapterus leucus)]. Total arsenic concentrations ranged from 0.167 to 2.40 mg As kg⁻¹ wet mass. The arsenic compounds extracted from the liver samples with a methanol/water mixture (9:1, v/v) were identified and quantified by anion- and cation-exchange chromatography. An ICP–MS equipped with a hydraulic high-pressure nebulizer served as the arsenic-specific detector. Arsenobetaine (0.052–1.67 mg As kg⁻¹ wet mass) was the predominant arsenic compound in all the liver samples. Arsenocholine was present in all livers (0.005–0.044 mg As kg⁻¹ wet mass). The tetramethylarsonium cation was detected in all pinnipeds ( < 0.009 to 0.043 mg As kg⁻¹) but not in any of the cetaceans. The concentration of dimethylarsinic acid ranged from < 0.001 to 0.109 mg As kg⁻¹ wet mass. Most of the concentrations for methylarsonic acid ( < 0.001 to 0.025 mg As kg⁻¹ wet mass) were below the detection limit. Arsenous acid and arsenic acid concentrations were below the detection limit of the method (0.001 mg As kg⁻¹). An unknown arsenic compound was present in all liver samples at concentrations from 0.002–0.027 mg As kg⁻¹. © 1998 John Wiley & Sons, Ltd.     

Experimental assessment of a large sample cell for laser ablation-ICP-MS, and its application to sediment core micro-analysis

The coupling of laser ablation (LA) to inductively coupled plasma-mass spectrometry (ICP-MS) enables the direct analysis of solid samples with micrometric resolution. Analysis is often restricted to relatively small samples owing to the dimensions of conventional ablation cells. Here, we assess the performance of a large rectangular, commercially-available sample cell which enables analysis over a 10.2?×?5.2 cm² area. Comparison with the conventional cell shows a small to moderate performance decrease for the large cell resulting from the dilution of ablated particles in a larger volume with a 4–31% lower signal output and longer signal tailings. The performance of this cell is however sufficient for the determination of both major and trace elements in many kinds of samples. The applicability of the large cell LA-ICP-MS setup was demonstrated by the determination of Al, Si, Mn, Fe, Cu, Zn Pb and U in sediment core sections at a resolution of 0.6 mm. Detection limits for sediment analysis were 7 mg Al kg^?1, 68 mg Si kg^?1, 0.5 mg Mn kg^?1, 20 mg Fe kg^?1, 0.2 mg Cu kg^?1, 0.3 mg Zn kg^?1, 0.08 mg Pb kg^?1 and 0.003 mg U kg^?1. Cyclic patterns, which would have been overlooked by conventional analysis at cm resolution, were observed in analysed sediments. This study demonstrates the potential of LA-ICP-MS in environmental analysis, with the large sample cell setup offering the possibility to analyse a wider range of samples without sectioning.     

Validation of a screening method for rapid control of macrocyclic lactone mycotoxins in maize flour samples

A procedure for the analytical validation of a rapid supercritical fluid extraction amperometric screening method for controlling macrocyclic lactone mycotoxins in maize flour samples has been developed. The limit established by European legislation (0.2 mg kg⁻¹), in reference to zearalenone (ZON) mycotoxin, was taken as the reference threshold to validate the proposed method. Natural ZON metabolites were also included in this study to characterize the final screening method. The objective was the reliable classification of samples as positive or negative samples. The cut-off level was fixed at a global concentration of mycotoxins of 0.17 mg kg⁻¹. An expanded unreliability zone between 0.16 and 0.23 mg kg⁻¹ characterized the screening method for classifying the samples. A set of 30 samples was used for the final demonstration of the reliability and usefulness of the method.     

Sequential spectrofluorimetric determination of free and total glycerol in biodiesel in a multicommuted flow system

A new procedure for spectrofluorimetric determination of free and total glycerol in biodiesel samples is presented. It is based on the oxidation of glycerol by periodate, forming formaldehyde, which reacts with acetylacetone, producing the luminescent 3,5-diacetyl-1,4-dihydrolutidine. A flow system with solenoid micro-pumps is proposed for solution handling. Free glycerol was extracted off-line from biodiesel samples with water, and total glycerol was converted to free glycerol by saponification with sodium ethylate under sonication. For free glycerol, a linear response was observed from 5 to 70 mg L⁻¹ with a detection limit of 0.5 mg L⁻¹, which corresponds to 2 mg kg⁻¹ in biodiesel. The coefficient of variation was 0.9% (20 mg L⁻¹, n = 10). For total glycerol, samples were diluted on-line, and the linear response range was 25 to 300 mg L⁻¹. The detection limit was 1.4 mg L⁻¹ (2.8 mg kg⁻¹ in biodiesel) with a coefficient of variation of 1.4% (200 mg L⁻¹, n = 10). The sampling rate was ca. 35 samples h⁻¹ and the procedure was applied to determination of free and total glycerol in biodiesel samples from soybean, cottonseed, and castor beans.     

A study of the elemental composition of diabases by instrumental neutron activation and X-ray fluorescence analysis

The distribution of the elemental composition was studied mainly for microelements in the diabases of the Pechenga suite subjected to various changes. Investigations were conducted by a combination of instrumental neutron activation INAA and X-ray fluoresence XRFA analyses. The INAA was conducted with sample weights of 20–100 mg exposed to irradiation in a nuclear reactor by a flux of neutrons ≈10¹³ n·cm⁻²·s⁻¹. Measurements were carried out by means of a semi-conductor gamma-spectrometer with a Ge(Li) detector. The determination of Al, Mn, Mg, Ti, V, Ca was conducted by short-lived isotopes, while the determination of Na, Sc, Fe, Co, Cr, Hf, Th, La, Ce, Sm, Eu, Yb, Lu by longlived ones. For XRFA samples weighing up to 2 g were irradiated by means of an¹⁰⁹Cd isotope source and were measured by a spectrometer with a Si(Li) detector and beryllium window. By this method we determined the Sr, Zr an Nb contents. Continuous distribution histograms were plotted for the concentration of 22 elements and some of their ratios. Considerable variations in microelemental composition observed in a number of cases make it possible to assess the character of past processes of diabasic change.     

Neutron activation analysis for the determination of contaminants in food contact materials

A neutron activation method has been developed for the analysis of high density polyethylene, low density polyethylene, polypropylene, polyethylene terephthalate and polystyrene. Samples weighing 2–5 g were irradiated in a thermal neutron flux of 10¹⁶ neutrons m^–2 s^–1 and measured with gamma ray spectrometry for 64 elements. With the method developed here over 50 elements can be detected at concentrations below 1 mg/kg. Correction factors were applied for neutron flux variation and counting geometry.The method was validated using reference material citrus leaves (NIST) for Na, Mg, Al, K, Ca, Mn, Cu, Sr and I, and a suite of in house standards doped with Al, Cr, Co, Mg, Zn and Sb confirmed repeatability of the method. The method was used to measure inorganic contaminants in the raw polymers and retail samples of plastic packaging used in contact with food.     

Copper content of vineyard soils at Sremski Karlovci (Vojvodina Province,Serbia) as affected by the use of copper-based fungicides

The present study investigated the copper content of nine vineyard plots soils and four control plots as affected by the application of copper-based fungicides. The study was carried out at the site of Sremski Karlovci in the Serbian province of Vojvodina. The results showed that Cu soil concentrations are increased at the site and that there is a tendency towards soil contamination by this element. Of the 27 total samples studied, only one had Cu concentration above the maximum allowable concentration of 100?mg?kg^?1. That sample's concentration was 111.7?mg?kg^?1. All the samples from the 0–15?cm layer had copper levels that were above the critical value of 60?mg?kg^?1. The mean value of the samples was 79.4?mg?kg^?1, contrasting with the background concentration of 19.8?mg?kg^?1. The results obtained for the studied vineyard soils indicate that these soils are potentially at risk and call for reduced application of Cu-based fungicides along with soil monitoring.     

Determination of lead in metallic reference materials by laser ablation combined with laser excited atomic fluorescence

Concentrations of lead in the range 0.15–750 μg⁻¹ were measured in metallic matrices (copper, brass, steel, and zinc) by laser excited atomic fluorescence combined with UV laser ablation in a low-pressure (130 mbar) argon atmosphere. The mass of material ablated was determined by repetitive weighing of the target prior to and after approximately 10 000 ablating shots. The fluorescence was excited after a 100 μs delay relative to the ablation pulse. A long integration time of 200 s was used to provide a representative determination of bulk concentrations. No matrix effect was observed, providing a universal calibration curve for all samples with relative standard deviations of about 20%. The relative and absolute limits of detection were 72 ng g⁻¹ and 0.5 fg, respectively.     

Amperometric determination of total cholesterol in serum with use of immobilized cholesterol esterase and cholesterol oxidase

Cholesterol esterase and cholesterol oxidase were immobilized on octyl-agarose gel, activated with cyanogen bromide and placed in a reactor. The sensor system for total cholesterol was assembled with the immobilized enzyme reactor, a hydrogen peroxide electrode and a peristaltic pump. Characteristics of the sensor system were investigated by using cholesterol palmitate as a standard substrate. A linear relationship was obtained between peak current and cholesterol palmitate concentration below 1000 mg dl^-1 (10.3 mM). A 10-μl sample could be assayed in 5 min. Total cholesterol in human serum was determined in the range 100–400 mg dl^-1. The standard deviation for the determination of 50 samples of 300 mg dl^-1 was 6 mg dl^-1 (2%). The system was used for 300 assays without loss of enzymatic activity. The correlation coefficient was 0.94 for 27 samples of human sera analyzed by the system proposed and by the conventional chemical method.     

In vitro and in vivo identification of metabolites of magnoflorine by LC LTQ‐Orbitrap MS and its potential pharmacokinetic interaction in Coptidis Rhizoma decoction in rat

Magnoflorine, an important aporphine alkaloid in Coptidis Rhizoma, is increasingly attracting research attention because of its pharmacological activities. The in vivo and in vitro metabolism of magnoflorine was investigated by LC LTQ‐Orbitrap MS. In vivo samples including rat urine, feces, plasma and bile were collected separately after both oral (50 mg kg^?1) and intravenous administration (10 mg kg^?1) of magnoflorine, along with in vitro samples prepared by incubating magnoflorine with rat intestinal flora and liver microsome. As a result, 12 metabolites were found in biological samples. Phase I metabolites were identified in all biological samples, while phase II metabolites were mainly detected in urine, plasma and bile. In a pharmacokinetic study, rats were not only dosed with magnoflorine via oral (15, 30 and 60 mg kg^?1) and intravenous administration (10 mg kg^?1) but also dosed with Coptidis Rhizoma decoction (equivalent to 30 mg kg^?1 of magnoflorine) by intragastric administration to investigate the interaction of magnoflorine with the rest of compounds in Coptidis Rhizoma. Studies showed that magnoflorine possessed lower bioavailability and faster absorption and elimination. However, pharmacokinetic parameters altered significantly (p < 0.05) when magnoflorine was administered in Coptidis Rhizoma decoction. Oral gavage of Coptidis Rhizoma decoction decreased the absorption and elimination rates of magnoflorine, which revealed that there existed pharmacokinetic interactions between magnoflorine and the rest of ingredients in Coptidis Rhizoma. Copyright © 2015 John Wiley & Sons, Ltd.     

Multielement Analysis of South Serbian Strawberry Cultivars by Inductively Coupled Plasma—Optical Emission Spectrometry

The contents of 17 elements in thirteen strawberry cultivars grown in the five districts of Southern Serbia were determined using inductively coupled plasma optical emission spectrometry (ICP-OES). The most abundant elements are K (875–1148 mg?·?kg^?1 fresh weight), P (307–664 mg?·?kg^?1 fresh weight), Ca (192–256 mg?·?kg^?1 fresh weight), and Mg (111–189 mg?·?kg^?1 fresh weight) in all samples. Strawberries were also found to be a good source of Sr (8.05–18.6 mg?·?kg^?1 fresh weight) and Fe (3.09–10.4 mg?·?kg^?1 fresh weight). The contents of As and Cd were below the detection limit (0.0828 mg?·?kg^?1 and 0.0205 mg?·?kg^?1, respectively) in all strawberry samples, while the contents of Ni, Cr, and Cu were below the recommended tolerable levels proposed by Joint Food and Agriculture Organization of the United Nations and World Health Organization Expert Committee on Food Additives, and did not a pose a health risk for the consumer. The application of Duncan’s test showed significant differences between contents of analyzed elements in all strawberry cultivars. The highest mean levels of analyzed elements were detected in strawberries grown in the Topli?ki, Jablani?ki, and P?injski districts. The spike recovery test was used to verify the accuracy of the method, and the spike recovery was in the range 93.8–107.8%. The contents of the metals in strawberry samples were also comparable with values previously reported in the literature.     

Volatile compounds composition and antioxidant activity of bee pollen collected in Lithuania

Characterization of volatile compounds composition and evaluation of antioxidant properties of bee pollen collected in Lithuania is presented in the paper, which is the first study on pollen of Lithuanian origin to our knowledge. Three polyfloral pollen samples collected by honey bees were analyzed. Characterization of volatile compounds was performed using solid phase microextraction (SPME) and GC-MS. Styrene was predominant in all samples contributing 19.6–27.0 mass %. Sample A distinguished by a high amount of limonene, 9.0 mass %, sample B differed from the rest by a high content of hexanal, 9.3 mass %, and nonanal, 12.3 mass %, while sample C showed the highest content of 1-tridecene, 43.3 mass %. Screening of antioxidant properties was carried out by spectrophotometric methods and liquid chromatography coupled with a post-column 1,1-diphenyl-2-picrylhydrazyl (DPPH) reaction detector and electrochemical detector. Total phenolic and flavonoid contents together with radical scavenging activity in the free radical (DPPH) model system were evaluated in the tested samples. Total phenolic content varied from 24.4 mg g^?1 to 38.9 mg g^?1, total flavonoid content was in the range of 7.3–10.0 mg g^?1 and radical scavenging activity was found between 30.7 mg g^?1 and 34.9 mg g^?1, all data are expressed in rutin equivalents. To process the collected data statistically and classify the bee pollen samples to clusters according to their volatile composition and antioxidant activity, principal component analysis, hierarchical cluster analysis and non-linear discriminant analysis were applied.