Amperometric detection of amino acids in a flow-injection system with a nickel(II)-modified electrode with an Eastman-AQ polymer film

Amperometic flow measurements were made at +0.55 V (vs. Ag/AgCl) in 0.1 mol l⁻¹ KOH electrolyte with an Ni(II) chemically modified electrode (CME) with an Eastman-AQ polymer film. The use and characteristics of a Ni(II)-containing crystalline and polymer-modified electrode obtained by a double coating step as a detector for amino acids in a flow-injection system using reversed-phase liquid chromatography are described. The detection of these analytes is based on the higher oxidation state of nickel (NiOOH) controlled by the applied potential. The electroanalytical parameters and the detection current for a series of amines and amino acids were investigated. The use of such a CME in the flow-injection technique was found to be suitable in a solution at low pH. The linear range for glycine is 5 × 10⁻⁶-0.1 mol l⁻¹ with a detection limit of 1.0×10⁻⁶ mol l⁻¹. A 1 × 10⁻⁴ mol l⁻¹ mixture of serine and tyrosine was also detected after separation on an Nucleosil C₁₈ column.     

Chemically modified electrode for the detection of carbohydrates

A nickel-catalysed chemically modified electrode is described which seems to represent a convenient compromise between ease of preparation, reproducibility, precision and detection limits for the determination of carbohydrates in biological matrices.     

Indirect conductimetric detection of amino acids after liquid chromatographic separation

A liquid chromatographic method using indirect conductimetric detection is proposed for the determination of low levels of organic compounds, which does not require any special functional characteristics of the analyte. The signal detected is proportional to the molar concentration of the analyte and independent of its nature. The detector response is linearly dependent on analyte concentrations over at least three orders of magnitude. The basis of the detection is to create a conducting background, which will decrease on elution of the organic compounds. The theory of the method is discussed, with special reference to the quantitative displacement of the conducting species of the mobile phase from the column by the analyte on sample injection. The proposed method has been applied to study the chromatographic behaviour of twenty-one amino acids, where a 5 -μm Econosil CN column was used as the stationary phase with a mixture of water-acetonitrile-tetrahydrofuran (70:20:3) containing 1 mM perchloric acid or trichloroacetic acid as the mobile phase. The proposed method allows as little as 10 ng of each amino acid to be determined.     

Simultaneous determination of amino acids and carbohydrates in culture media of Clostridium thermocellum by valve-switching ion chromatography

An improved method for the simultaneous determination of 20 amino acids and 7 carbohydrates using one-valve switching after injection, ion chromatography, and integrated pulsed amperometric detection is proposed. The resolution of the amino acids and carbohydrates in the cation trap column was investigated. In addition, parameters including flow liquid type, flow rate, concentration, and valve-switch timing were optimized. The method is time-saving, effective, and accurate for the simultaneous separation of amino acids and carbohydrates, with a mean correlation coefficient of >0.99 and repeatability of 0.5–4.6% for eight replicates. The method was successfully applied in the analysis of amino acids and carbohydrates in aseptic media and in extracellular culture media of three phenotypes of Clostridium thermocellum.     

Comparison of pulsed amperometric detection and integrated voltammetric detection for inorganic sulfur compounds in liquid chromatography

A Variety of potential–time waveforms are useful in pulsed electrochemical detection (PED) when applied for the amperometric detection of numerous polar organic compounds following their separation by liquid chromatography (LC). Here, we compare the waveforms for pulsed amperometric detection (PAD) and integrated voltammetric detection (IVD) applied for detection of organosulfur compounds at Au electrodes in acidic media. In PAD waveforms, electrodes response is measured at a constant detection potentials. In IVD waveforms, electrodes current is integrated throughout a fast cyclic scan of the detection potential. As a consequence of this difference in detection strategy, the background signal for IVD is significantly smaller for PAD in the detection of organosulfur compounds whose response mechanisms require the concomitant formation of surface oxides on Au electrodes. Furthermore, in comparison to Pad, IVD has a larger sensitivity and a diminished system peak from 0₂ dissolved in the sample. Use of a preadsorption step increases detection sensitivity in both PAD and IVD. The limit of detection (S/N=3)for cysteine in LC-IVD is ca. 6 nM for a 50-μl injection (i.e., 300 fmol) using a detection waveform that includes a 1000-ms preadsorption period.     

Selective determination of amino acids using flow injection analysis coupled with chemiluminescence detection

The determination of the amino acids proline, histidine, tyrosine, arginine, phenylalanine and tryptophan using flow injection analysis (FIA) with chemiluminescence detection is described. Proline was the only amino acid to exhibit chemiluminescence with the tris(2,2-bipyridyl)ruthenium(III) reaction at pH 10. While, histidine was found to selectively enhance the reaction of luminol with Mn(II) salts in a basic medium. Acidic potassium permanganate chemiluminescence was able to selectively determine tyrosine at pH 6.75. Low pressure separations using a C18 guard column allowed the simultaneous determination of tyrosine and tryptophan or phenylalanine and tryptophan with acidic potassium permanganate and copper(II)-amino acid-hydrogen peroxide chemiluminescence, respectively. Precision for each method was less than 3.9% (R.S.D.) for five replicates of a standard (1×10⁻⁵ M) and the detection limits ranged between 4×10⁻⁹ and 7×10⁻⁶ M. Preliminary investigations revealed that the methodology developed was able to selectively determine the individual amino acids in an equimolar mixture of the 20 naturally occurring amino acids.     

Pulsed amperometric detection of underivatized amino acids using polypyrrole modified copper electrode in acidic solution

The successful pulsed amperometric detection of underivatized amino acids have been carried out in an acidic media on a polypyrrole (PPy) modified Cu electrode. The formation of PPy film doped with glutamate (glu) on a Cu electrode surface changes the mechanism of Cu dissolution. After application of multistep potential waveform, the PPy film was glu free due to the electro-reduction and overoxidation. High anodic potential polarization treatment yielded partially overoxidized PPy film as long as the Cu surface dissolution and amino acid permeation through the film was well controlled. This overoxidized PPy film acted as a charge and size exclusion barrier in order to improve the selectivity and stability of a Cu electrode. Various process parameters such as film modification time, detection and cleaning potential and pH of solution have been optimized to maximize the beneficial electrocatalytic properties of the electrode surface. At an optimized condition, detection limits for positively charged histidine and arginine are 19 and 22 pg respectively, whereas the neutral amino acids detected in amounts of 0.9–2.3 ng. Furthermore, the PPy coated Cu electrode response was long lived, stable and reproducible.     

多壁碳纳米管修饰电极用于离子色谱分离电活性氨基酸的安培检测

将经羧基化的多壁碳纳米管(MWNTs)修饰在玻碳电极表面,制得碳纳米管修饰电极,并通过循环伏安法研究了某些可氧化的氨基酸在该电极上的电催化行为。该电极对半胱氨酸,色氨酸和酪氨酸有明显的电催化作用,且具有较高的灵敏度和稳定性。在一定的色谱条件下,经过离子色谱分离,这些可氧化的氨基酸的检测限分别为:半胱氨酸7.0×10-7mol L;色氨酸2.0×10-7mol L;酪氨酸3.5×10-7mol L(3倍信噪比)。方法已用于头发中这些氨基酸含量的测定。     

Synthesis and characterization of chiral iron carbonyl complexes from imine ligands with carbohydrates and amino acids as substituents

Imine ligands derived from 6-amino-6-desoxy-1,2,3-O-trimethyl--d-glucopyranose or from various amino acid esters react with Fe₂(CO)₉ to give chiral iron carbonyl complexes. Derivatives produced from benzaldehyde react via a C–H activation reaction in ortho-position with respect to the exocyclic imine substituent followed by an intramolecular hydrogen transfer reaction of the activated hydrogen towards the former imine carbon atom. The molecular structure of the diiron hexacarbonyl complexes of benzylideneamino-l-phenylalanine ethyl ester and benzylideneamino-l-methionine methyl ester were characterized by means of X-ray structure determinations. Imines produced from cinnamaldehyde upon reaction with Fe₂(CO)₉ produce mononuclear iron tricarbonyl complexes with the imine ligand being coordinated in a η⁴-fashion.     

Ultraviolet thermal lensing detection of amino acids

Thermal lensing (TL) permits ultra-sensitive measurements of optical absorption of analytes in very small liquid volumes. We report the construction and use of a TL detector based on pulsed ultraviolet (UV) laser excitation (266 nm). We applied this detector to quantitate amino acids using capillary electrophoresis (CE) as a means of separation. Sixteen individual amino acids are readily detected, but the signal has a complex dependence on intensity caused by the combination of (1) one-photon absorption; (2) two-photon absorption (TPA); and (3) photodestruction of amino acid molecules in the focus of the laser beam. An aqueous solution containing tyrosine, tryptophan, and cysteine is electrophoretically separated and the individual amino acids are detected by UV TL. The estimated limit of detection is 7 microM for tyrosine, 2.5 microM for tryptophan and 33 microM for cysterine, which translates into 0.35 fmol for tyrosine, 0.125 fmol for tryptophan, and 1.65 fmol for cysteine in the 140pL detection volume. It is found that two-photon absorption of water and the formation of color centers in the fused silica walls of the flowcell can contribute a significant, drifting background signal, but this interference can be minimized by selecting an appropriate focus condition and excitation-detection geometry. We suggest that as UV laser sources become available, UV TL may become a method of choice for measuring the concentrations of many analytes in different separation formats in which the volume is highly limited.     

Evaluation of conditions for the HPLC determination of plasma amino acids using precolumn derivatization

For the determination of free amino acids in plasma, the conditions for precolumn derivatization of the amino acids and the chromatographic separation were examined. The isoindole products, formed by the reaction of the primary amino acids with orthophthalaldehyde (OPA), were readily separated by RPLC and detected spectrofluorometrically using an excitation wave-length of 300 nm and an emission cut-off filter of 440 nm. Since the sensitivity of this method permits determination of amino acids in the femtomole range, the analysis can be performed on samples as small as 10 μl of filtered plasma or serum. The separation is achieved in approximately 35 minutes with good precision for the majority of the amino acids.     

High-performance anion-exchange chromatography of carbohydrates using a new resin and pulsed amperometric detection

Summary This paper reports the results of a study on the use of a new polymer-based, strong anion-exchange, stationary phase for rapid and selective separation of carbohydrates and related compounds by high-pH, anion-exchange chromatography with pulsed amperometric detection. The new adsorbent has been obtained by direct nitration of 2.8 μm, spherical non-porous highly cross-linked, styrene-divinylbenzene copolymer beads, followed by reduction of superficially introduced nitro groups with nascent hydrogen and quaternization of the resultant amino groups with iodomethane. It is reported that by optimizing the ionic strength of the mobile phase, columns packed with the new anion-exchanger can be successfully employed to separate, either in isocratic or gradient elution mode, oligosaccharides, positional isomers of gluco-disaccharides, as well as uronic acids and sugar monophosphates.     

Nanostructured cupric oxide electrode: An alternative to amperometric detection of carbohydrates in anion-exchange chromatography

In this paper, a new and low cost copper/cupric oxide nanostructured electrode is presented as an alternative to the amperometric detection of carbohydrates in high-performance anion exchange chromatography. The modified copper electrodes were prepared by a simple and fast method which resulted in the obtainment of homogeneously distributed nanostructures adhered to the surface with controlled chemical nature. The results, when compared to conventional copper electrodes, exhibited considerable improvements in analytical results, including: 1) Better repeatability in consecutive glucose detections, in which the percent relative standard deviation improved from 15.1% to 0.279%. 2) Significant improvements in the stability of the baseline and a decrease of the stabilization time, going from several hours to approximately 15 min. 3) Considerable increase in the sensitivity towards glucose, from 5.02 nA min mg L⁻¹ to 25.5 nA min mg L⁻¹. 4) Improvements in the detectability with limits as low as 1.09 pmol. 5) Wide working range of concentrations (1 × 10⁻² to 1 × 10⁴ mg L⁻¹). 6) Good linearity with correlation coefficients greater than 0.998. 7) Possibility of detecting different molecules of carbohydrates (lactose, maltose, sucrose cellobiose, sorbitol, fructose, glucose, galactose, manose, arabitol, xylose, ribose and arabnose). In comparison to the electrode that is more employed for this type of application (gold electrode), the low cost, the possibility of detection at constant potential and the equivalent detection limits presented by the new electrode material introduced in this work emerge as characteristics that make this material a powerful alternative considering the detection of carbohydrates in anion exchange chromatography.     

Pulsed amperometric detection at glassy carbon electrodes: A new waveform for sensitive and reproducible determination of electroactive compounds

In this work, the application of a new pulsed amperometric detection (PAD) waveform at a glassy carbon electrode, operating in typical chromatographic mobile phases, is proposed for the sensitive and reproducible determination of arylethanolaminic and phenolic moiety based compounds (e.g. beta-agonists and polyphenols). Preliminary experiments by cyclic voltammetry were carried out to investigate the electrochemical behaviour and to select the detection and cleaning electrode potentials. The proposed potential-time profile was designed to prevent the carbon electrode fouling under repeated analyses, thus ensuring a reproducible and sensitive quantitative determination, without the need of any mechanical or chemical electrode cleaning procedure. The waveform electrochemical parameters, including detection and delay times, were optimized in terms of sensitivity, limit of detection and response stability. The optimized waveform allowed the sensitive and stable detection of model compounds, such as clenbuterol and caffeic acid, that showed detection limits of 0.1 μg L⁻¹ and 14 μg L⁻¹, quantification limits of 0.4 μg L⁻¹ and 46 μg L⁻¹, and linearity up to 100 μg L⁻¹ (r = 0.9993) and 10 mg L⁻¹ (r = 0.9998), respectively. Similar results were obtained for other compounds of the same classes, with precision values under repeatability conditions ranging from 3.0 to 5.9%. The proposed method can be then considered as an excellent alternative to the post-column detection of beta-agonists, phenols and polyphenols.     

Highly sensitive determination of ectoine and other compatible solutes by anion-exchange chromatography and pulsed amperometric detection

In saline media prokaryotes compensate for the osmotic pressure of the surrounding medium by producing osmolytes. Although these osmolytes or osmoprotectors have quite diverse structures, most of them can be determined by anion-exchange chromatography combined with integrated pulsed amperometric detection. This technique offers the advantages of very high sensitivity and new opportunities to determine ectoine and 5-hydroxyectoine—two important osmolytes —after hydrolytic cleavage of the pyrimidine ring. It can even be used to screen bacterial colonies on agar for compatible solutes. Furthermore, it allows amino acids and osmolytes of this type to be determined without derivatization. To test the method we applied it to two halotolerant bacterial strains: Stenotrophomonas rhizophila DSM 14405^T and Halomonas elongata DSM 2581^T. The first strain produced trehalose and glucosylglycerol, and the second ectoine, as the main osmotic counterweight. The relationship between the content of these osmolytes in the bacterial biomass and the external salinity is described.     

Separation of amino acids in glucose isomerase crystal: Insight from molecular dynamics simulations

The separation of amino acids (Arg, Phe and Trp) in a liquid chromatography is investigated using molecular dynamics simulations. A bioorganic nanoporous material – glucose isomerase crystal – is used as the stationary phase and water as the mobile phase. The transport velocities of amino acids decrease in the order Arg > Phe > Trp, consistent with experimental measurement. The elution order is not affected by the solute concentration or by the flowing rate of mobile phase. Arg is highly hydrophilic and charged, interacts with water the most strongly, and thus moves with flowing water the fastest. Trp has the largest van der Waals volume and encounters the largest steric hindrance, leading to the slowest velocity. From the number distributions of amino acids around protein surface, Trp and Phe are found to stay closer to protein than Arg. The solvent-accessible surface areas of amino acids and the numbers of hydrogen bonds between amino acids and water further elucidate the observed velocity difference. The simulation results provide useful microscopic insight into the retention mechanisms in chromatographic separation process and suggest that glucose isomerase crystal has the capability to separate amino acids.     

Potentiometric detection of organic acids in liquid chromatography using conducting oligomer electrodes

A conducting oligomer electrode was used for the potentiometric detection of organic acids in reversed phase liquid chromatography (LC). The conducting material consisted of a mixture of a phenylene vinylene trimer with a polycarbonate host polymer and iodine. A glassy carbon electrode was coated with this material by evaporation from a chloroform solution. A theoretical model was given to describe the observed potentiometric responses. The analysis conditions were optimized to obtain both efficient separations, and sensitive potentiometric responses. Detection limits in the nanogram level were attained when a 1 mM phosphoric acid solution was used as the eluent, which were comparable to the values obtained with low-wavelength UV detection. Calibration curves showed a logarithmic dependence on an injected amount for amounts higher than 5 nmol, and a linear dependence for injected amounts below this value. The response times of the electrode were smaller than 1 s at typical LC flow-rates. The reproducibility for consecutive injections was 5%.     

Optimization of the electrodeposition of copper on poly-1-naphthylamine for the amperometric detection of carbohydrates in HPLC

A modified electrode consisting of copper dispersed in a poly-1-naphthylamine (p-1-NAP/Cu) film on a glassy carbon electrode was used as an amperometric detector for the on-line analysis of various carbohydrates separated by high performance liquid chromatography. The results obtained with this new sensor were compared to those obtained with a modified electrode based on the same polymer but with copper ions incorporated at open circuit, as described in a previous paper. In this new modified electrode the copper microparticles were electrochemically deposited into the polymeric matrix by single potential step chronoamperometry. A nucleation and growth mechanism was proposed to explain the current transients of copper electrodeposition. The experimental results were fitted to the proposed mechanism by using a mathematical equation that considers three-dimensional growth and progressive nucleation, assuming a no overlap and no diffusion mechanism. Cyclic voltammetric experiments showed that the electrodeposited copper microparticles provided a catalytic surface suited for the oxidation of glucose and several carbohydrates. The sensitivity of the electrode was influenced by the amount of copper electrodeposited, which in turn depended on the applied overpotential used for the deposition of copper. Liquid chromatographic experiments were carried out to test the analytical performance of these electrodes for the determination of various carbohydrates.     

Selective detection in flow analysis based on the combination of immobilized enzymes and chemically modified electrodes

The combination of immobilized enzymes and amperometry to build selective detection devices in flow-injection analysis and liquid chromatography is described. The pros and cons of enzyme electrodes and of immobilized enzyme reactors are discussed. The paper concentrates on the use of immobilized dehydrogenases, oxidases, peroxidases, and on electrodes on which these enzyme reactions can be selectively followed. The work in the field by the authors is reviewed.