Flow injection conductometric system with gas diffusion separation for the determination of Kjeldahl nitrogen in milk and chicken meat

A simple flow injection (FI) conductometric system with gas diffusion separation was developed for the determination of Kjeldahl nitrogen (or proteins) in milk and chicken meat. The sample was digested according to the Kjeldahl standard method and the digest was diluted and directly injected into the donor stream consisting of 4 M NaOH. In alkaline medium, ammonium was converted to ammonia, which diffused through the PTFE membrane to dissolve in an acceptor stream (water). Dissociation of ammonia caused a change in conductance of the acceptor solution, which was linearly proportional to the concentration of ammonium originally present in the injected solution. A conductometric flow through cell and an amplifier circuit was fabricated, which helped improve sensitivity of the conductometric detection system. With using a plumbing Teflon tape as a gas diffusion membrane and without thermostating control of the system, a linear calibration graph in range of 10-100 mg L⁻¹ N-NH₄ was obtained, with detection limit of 1 mg L⁻¹ and good precision (relative standard deviation of 0.3% for 11 replicate injections of 50 mg L⁻¹ N-NH₄). The developed method was validated by the standard Kjeldahl distillation/titration method for the analysis of milk and chicken meat samples. The proposed system had sample throughput of 35 h⁻¹ and consumed much smaller amounts of chemical than the standard method (275 mg vs 17.5 g of NaOH per analysis, respectively).     

Flow-injection spectrophotometric determination of chloride with an on-line solid mercury(II) thiocyanate minicolumn and bromide with a silver thiocyanate minicolumn

Flow-injection spectrophotometric procedures are described for the determination of chloride and bromide using on-line solid mercury(II) thiocyanate and silver thiocyanate minicolumns, respectively. The linear response ranges for chloride and bromide are 0.28 × 10^?4?8.5 × 10^?4 M and 0.38 × 10^?4?2.4 × 10^?4 M, respectively. The sample throughput for both systems is 100 h^?1. The lifetime of the minicolumns is 50 and 200 injections, respectively.     

Gas diffusion sequential injection system for the spectrophotometric determination of free chlorine with o-dianisidine

A gas diffusion sequential injection system for spectrophotometric determination of free chlorine is described. The detection is based in the colorimetric reaction between free chlorine and a low toxicity reagent o-dianisidine. A gas diffusion unit is used to isolate free chlorine from the sample in order to avoid possible interferences. This feature results from the conversion of free chlorine to molecular chlorine (gaseous) with sample acidification. With minor changes in the operating conditions, two different dynamic ranges were obtained enhancing the application both to water samples and bleaches. The results obtained with the developed system were compared to the reference method, iodometric titration and proved not to be statistically different. A detection limit of 0.6 mg ClO⁻/L was achieved. Repeatability was evaluated from 10 consecutive determinations being the results better than 2%. The two dynamic ranges presented different determination rates: 15 h⁻¹ for 0.6-4.8 mg ClO⁻/L (water samples) and 30 h⁻¹ for 0.047-0.188 g ClO⁻/L (bleaches).     

Flow-injection catalytic kinetic determination of manganese using stopped-flow and gradient calibration

Based on the principle of Mn(II) catalysis of the Tiron-hydrogen peroxide reaction, a catalytic kinetic spectrophotometric determination of traces of manganese (ca. 10^?7 M) by flow injection was established. In combination with a microcomputer, by using gradient dilution and the stopped-flow method, onlya single standard solution was needed for calibration. The method has a high selectivity and a sampling rate of 40 h^?1. Traces of manganese in natural water were determined with a maximum relative standard deviation of 5.5% (n = 6).     

Flow-injection determination of ammonia in kjeldahl digests by gas diffusion and conductometry

A flow injection/conductometric method is proposed for determing ammonia in solutions obtained from Kjeldahl digestion. The method is based on diffusion of ammonia through a PTFE membrane from an alkaline (NaOH/EDTA) medium to a deionized water stream. The change in conductance of the deionized water stream is proportional to the ammonia concentration present in the digest. The effects of flow parameters, temperature and potential interferences are reported. Approximately 100 samples can be injected per hour; the precision is about 1%. Results for total nitrogen in vegetable tissues, animal feeds and fertilizers are in good agreement with those obtained by the usual distillation/titration method.     

Flow-injection spectrophotometric determination of ascorbic acid by reduction of vanadotungstophosphoric acid

Ascorbic acid may be determined spectrophotometrically at 360 nm based on reduction of vanadotungstophosphoric acid using flow-injection analysis. The carrier stream was distilled water and the reagent streams were buffer solution (pH 3.0), 1.735 × 10^?3 M dodecatungstophosphoric acid and 1.735 × 10^?3 M sodium vanadate. The injection rate was 80 h^?1. The calibration graph was linear up to 80 μg ml^?1 ascorbic acid and the relative standard deviation for the determination of 20 μg ml^?1 ascorbic acid was 1.5% (n=10). The detection limit was 1.0 μg ml^?1 ascorbic acid, based on an injection volume of 250 μl. The system was applied to the determination of ascorbic acid in vitamin C tablets.     

Gas diffusion-flow injection determination of total inorganic carbon in water using tungsten oxide electrode

A novel gas diffusion-flow injection method has been developed for the rapid and sensitive determination of total inorganic carbon (TIC) in water. The method is based on the diffusion of CO₂ across gas permeable membrane from a donor stream containing 0.1 M HCl to an acceptor stream of sodium acetate (10⁻⁵ mol l⁻¹ and pH 10). The CO₂ trapped in the acceptor stream passes through an electrochemical flow cell contains a tungsten oxide wire and a silver/silver chloride electrode, where it was sensitively detected. The parameters affecting the sensitivity of the electrode such as buffer concentration, pH, flow rate and injected volume were studied in detail. The electrode response was linear in the concentration range from 5 to 100 μg ml⁻¹ CO₃²⁻ with a correlation coefficient (R²) of 0.998. Precision (R.S.D.) was 1.42% for 20 μg ml⁻¹ standard solution of CO₃²⁻ (n=10). The detection limit was 0.20 μg ml⁻¹ CO₃²⁻. The method was evaluated by the injection of real natural water samples and an average recovery of 100.1% was obtained. The sampling rate was 30 samples h⁻¹. The method is simple, feasible with satisfactory accuracy and precision and thus could be used for monitoring TIC in water.     

Comparison of several solid-phase extraction sorbents for continuous determination of amines in water by gas chromatography-mass spectrometry

A semiautomatic method has been proposed for the determination of different types of amines in water samples including anilines, chloroanilines, N-nitrosamines and aliphatic amines. The analytes were retained on a solid-phase extraction sorbent column and after elution, 1 μL of the extract was analysed by gas chromatography coupled with electron impact ionization mass spectrometry. A systematic overview is given of the advantages and disadvantages of several sorbents (LiChrolut EN, Oasis HLB, RP-C₁₈, graphitized carbon black, fullerenes and nanotubes) in the retention of amine compounds and based on sensitivity, selectivity and reliability. The retention efficiency for the studied amines was higher (ca. 100%) with LiChrolut EN and Oasis HLB than it was with RP-C₁₈ and fullerenes (53 and 62%, respectively, on average). Detection limits of 0.5-16 ng L⁻¹ for the 27 amines studied were obtained when using a sorbent column containing 75 mg of LiChrolut EN for 100 mL of sample, the RSD being lower than 6.5%. The method was applied with good accuracy and precision in the determination of amines in various types of water including river, pond, tap, well, drinking, swimming pool and waste.     

Flow-injection technique for the determination of low levels of phosphorus in natural waters

An inexpensive flow-injection instrument for determining low concentrations of dissolved reactive phosphorus in natural waters is reported. The unique feature is the use of an inexpensive detector consisting of a flow cell and a simple photometer that incorporates a super-bright light-emitting diode as the source and a photodiode as the detector. The tin(II) chloride-molybdate method was optimized using a modified simplex optimization method. Silicate interference up to 5 mg Si l^?1 was removed by addition of 0.10% (w/v) tartaric acid. Using the tartaric acid-modified optimized reagents, a detection limit of 0.6 μg P l^?1 was achieved. The method was linear over the range 0–100 μg P l^?1 with an excellent precision (r.s.d. 2.9% at 2.0 and 0.5% at 50 μg P l^?1). An in-line pre-concentration anion-exchange column was used to obtain an even lower detection limit of 0.1 μg P l^?1 and applied to the analysis of real samples.     

Direct determination of acrylamide in food by gas chromatography with nitrogen chemiluminescence detection

A method of gas chromatography with nitrogen chemiluminescence detection and using standard addition is described for the determination of acrylamide in heat‐processed foods. Using a modified QuEChERS (quick, easy, cheap, effective, rugged, and safe) sample preparation method removes the acrylamide precursors completely, and the risk of overestimating acrylamide concentration due to additional analyte formation in the hot gas chromatograph inlet is also avoided. Sample preparation is rapid and inexpensive. A Deans switch device is utilized to heart‐cut acrylamide and to prevent interferences from the solvent and matrix from reaching the detector. The pre‐column is backflushed at high temperature to maintain a clean baseline and shorten the cycle time compared to baking out the column. Quantitation using standard addition is employed for compensation of potential variability in the acrylamide extraction efficiency in acetonitrile. The limit of detection and the limit of the quantification obtained for this method are 27 and 81 μg/kg, respectively, in food samples (equivalent to 3.5 and 10.6 μg/L in acetonitrile, respectively), and the linear range is 76–9697 μg/kg in food samples (equivalent to 10–1280 μg/L in acetonitrile) with an R² value of 0.9999.     

Flow-injection spectrophotometric determination of arylamines and sulphonamides by diazotization and coupling in a micellar medium

In a sodium dodecyl sulphate (SDS) micellar solution, the rate of coupling of a diazonium ion with N-(1- naphthyl)ethylenediamine (NED) increases greatly, the protonation of the resulting azo dyes takes place at higher pH values and the dyes are more soluble. These favourable features were applied to the development of a simple flow-injection spectrophotometric procedure for the determination of diazotizable substances of pharmaceutical interest. Limits of detection in the range 0.2–0.5 μg ml^?1 (signal-to-noise ratio=3), with relative standard deviation of 0.7–3% (n=3) for 5 μg ml^?1 standards, were obtained.     

A new method of making a gas diffusion electrode

A technique is described for production of a gas diffusion electrode by electrophoresis.Presented at the 3rd International Meeting on Advanced Batteries and Accumulators, 16–20 June 2002, Brno, Czech Republic     

Flow-injection fluorimetric assay of nitrogen-containing substrates by on-line enzymatic generation of ammonia

A fluorimetric flow-injection method for the determination of nitrogen-containing substrates, which can be enzymatically degraded to ammonium/ammonia is described. The generated ammonia is detected fluorimetrically after on-line derivatization with o-phthaldialdehyde (OPA) and sulphite. The derivatization procedure is optimized by a fractional factorial design at two levels and by a super modified simplex procedure to obtain a high sensitivity and a low detection limit for ammonia in the micromolar concentration range. Under the given flow conditions the detection limit is 1 μM, and considerable selectivity for ammonia over primary amines such as unconverted substrate and amino acids is achieved. Two enzymatic systems, incorporating immobilized creatinine iminohydrolase (CIH) and L-aspartase column reactors, respectively, are tested as model systems. The feasibility of the CIH system for the practical assay of creatinine in serum samples is demonstrated.     

A membraneless gas diffusion unit: design and its application to determination of ethanol in liquors by spectrophotometric flow injection

This work presents new design of a gas diffusion unit, called ‘membraneless gas diffusion (MGD) unit’, which, unlike a conventional gas diffusion (GD) unit, allows selective detection of volatile compounds to be made without the need of a hydrophobic membrane. A flow injection method was developed employing the MGD unit to determine ethanol in alcoholic drinks based on the reduction of dichromate by ethanol vapor. Results clearly demonstrated that the MGD unit was suitable for determination of ethanol in beer, wine and distilled liquors. Detection limit (3S/N) of MGD unit was lower than the GD unit (GD: 0.68%, v/v; MGD: 0.27%, v/v). The MGD design makes the system more sensitive as mass transfer is more efficient than that of GD and thus, MGD can perfectly replace membrane-based designs.     

A multi-commuted flow injection system with a multi-channel propulsion unit placed before detection: Spectrophotometric determination of ammonium

A flow system with a multi-channel peristaltic pump placed before the solenoid valves is proposed to overcome some limitations attributed to multi-commuted flow injection systems: the negative pressure can lead to the formation of unwanted air bubbles and limits the use of devices for separation processes (gas diffusion, dialysis or ion-exchange). The proposed approach was applied to the colorimetric determination of ammonium nitrogen. In alkaline medium, ammonium is converted into ammonia, which diffuses over the membrane, causing a pH change and subsequently a colour change in the acceptor stream (bromothymol blue solution). The system allowed the re-circulation of the acceptor solution and was applied to ammonium determination in surface and tap water, providing relative standard deviations lower than 1.5%. A stopped flow approach in the acceptor stream was adopted to attain a low quantification limit (42 μg L⁻¹) and a linear dynamic range of 50–1000 μg L⁻¹ with a determination rate of 20 h⁻¹.     

Monitoring and control of biological removal of phosphorus and nitrogen by flow-injection analysers in a municipal pilot-scale waste-water treatment plant

A flow-injection system is used for monitoring and control of a biological waste-water treatment plant with biological removal of phosphate and nitrate. The waste-water treatment plant is an activated sludge type on a pilot scale, with municipal waste water as the influent. The flow-injection system monitors the concentrations of phosphate, ammonia and nitrate in four places: in the inlet, in the outlet of the anaerobic pretreatment tank, in one of the aeration tanks and in the outlet of the plant. Sampling is carried out via a cross-flow filter system, based on an ultra-filtration membrane. The analysers employ highly pulsating, single-piston liquid chromatographic pumps. Synchronization of injection time and pump pulses eliminates the need for pulse-damping devices and ensures high reproducibility. The chemical methods are based on classical colorimetric methods. The measurement system has been designed with emphasis on long-term stability, low reagent consumption and minimum maintenance. To maintain stable, low flow-rates, on-line degassing has been installed for each reagent. Further, on-line standard calibration is being used to compensate for drift in the sensitivity of the analysers. The system is controlled by a PC, programmed in ASYST. The calibrated data is fed to a programmable logic controller (PLC), which also controls the pilot plant. A supervisory PC, programmed in Factory Link, stores and presents data. The measurements will be used for studies of different control strategies for the plant, e.g., rule-based control.     

Preparation of calibration gas mixtures of water and nitrogen by using diffusion tubes

A new type apparatus of computer control dynamic volumetric method was designed in corresponded with ISO 6145-8. It will be useful to solve the problem of pressure variety above the diffusion tube and its effects to the diffusion rate. The calibration gas mixtures of water in nitrogen in the ranges of 10⁻⁷∼10⁻⁶ mol/mol were prepared by this method with the relative uncertainty smaller than 5%.Presented at International Symposium on Metrology in Chemistry, 2004 Beijing, China.     

Simultaneous determination of the three main inorganic forms of nitrogen by ion chromatography

An ion chromatographic method for the determination of nitrite, nitrate and ammonium simultaneously is described. An appropriate eluent-column-detector combination for separating and detecting these ions is discussed. On a bifunctional ion-exchange column, nitrite and nitrate anions were separated by anion exchange and ammonium cation by cation exchange. Nitrite and nitrate were detected by UV spectrometry and ammonium using a chemically suppressed conductivity detector. The detection limits for the three ions were all below 0.02 ppm (w/w) and the relative standard deviations for the three ions were all less than 0.5%. Several samples such as water, soil and acid rain were analysed with this method and the recoveries of the three ions were all within 100 ± 5%. These results agreed well with those obtained by a standard method.     

Amperometric determination of cyanides at the low ppb level by automated preconcentration based on gas diffusion coupled to sequential injection analysis

A simple, sensitive method for determining free cyanides is described. The assay is based on automated gas diffusion of the analyte using sequential injection analysis (SIA) coupled to amperometric detection on a silver working electrode. The effects of varying several parameters affecting the analytical procedure (including the flow rates of the donor and acceptor streams, the concentrations of the reagents and the sample volumes) were studied. The validity and quality of the method were also assessed, by examining its linearity, limits of detection and quantitation, precision, selectivity to potentially interfering substances. Its sensitivity can be enhanced by applying a simple preconcentration step, following which limits of detection were found to be 0.05-0.12 μg L⁻¹. Application of the proposed assay to the analysis of tap, mineral and table water samples spiked at concentrations ranging from 1 to 10 μg L⁻¹ CN⁻, yielded satisfactory recoveries (88-112%).     

Flow-injection determination of phenylephrine hydrochloride in pharmaceutical dosage forms with on-line solid-phase extraction and spectrophotometric detection

A flow injection method is proposed for the determination of phenylephrine hydrochloride in pharmaceutical dosage forms. The method involves the use of on-line solid-phase extraction by means of a microcolumn containing Dowex 50W X8 ion-exchange resin for the separation of the analyte prior to colour development and spectrophotometric detection in the visible region.

The influence of preconcentration flow, preconcentration pH and elution volume was studied.

The method exhibits appropriate linearity (r² = 0.9999) which was proved statistically by means of the “F”-test. When applied to commercial samples containing several active ingredients and excipients, a significant reduction of interferences was found. Accuracy, evaluated by means of the spike recovery method was in the range 99.7–100.8%, with precision (R.S.D., %) better than 1%.

In order to achieve the automation the system was controlled from a notebook computer by means of a program written in QuickBASIC language. Under these conditions, a sampling frequency of 40 samples per hour could be attained.