双道氢化物发生-原子荧光光谱法同时测定核电用钢中痕量砷和锑

建立了双道氢化物发生-原子荧光光谱法同时测定核电用钢中痕量砷和锑的新方法。用王水溶解样品,以2.0 g/L L-半胱氨酸溶液作为预还原剂,在低酸度条件下实现对砷、锑的预还原。用20 g/L硼氢化钾溶液作为还原剂,氢化物发生反应在0.5 mol/L乙酸介质中进行。砷、锑的质量浓度在40μg/L范围与相应的荧光强度呈线性关系,方法的检出限(3s/k)分别为0.032μg/L和0.022μg/L。应用此方法同时测定了核电用钢及不锈钢标准样品中的砷锑含量,并与电感耦合等离子体原子发射光谱法的分析结果作了对比,测定值与标准样品的标准值相符,结果的相对标准偏差(n=8)均小于5.0%。     

Determination of phosphorus in steels by radiochemical neutron activation analysis

The viability of radiochemical neutron activation analysis as a method for certification of phosphorus in steels was tested by analysis of SRM low alloy steels. Preliminary results are generally in agreement with certified values. The limit of detection, as defined by Currie¹, was determined to be 5 μg/kg.     

含铈不锈钢的抗菌性能

以00Cr18Ni9不锈钢成分为基础,添加0～5%的稀土元素铈（Ce）.利用电子探针分析了加铈（Ce）不锈钢中Ce的分布;用化学分析法测定了含铈不锈钢中铈（Ce）和碳（C）的含量;用X射线衍射方法测试了含铈（Ce）不锈钢中铈（Ce）的析出相成分;采用贴膜法测试了含Ce不锈钢对大肠杆菌ATCC 8099、金黄色葡萄球菌ATCC 6538的抗菌性能.结果表明： 含Ce不锈钢具有优异的抗菌性能,与含Cu抗菌不锈钢相比,含Ce不锈钢无需时效热处理就具有优异的抗菌性能.并讨论了含Ce不锈钢的抗菌机制.     

Simultaneous determination of bismuth and tellurium in steels by high power nitrogen microwave induced plasma atomic emission spectrometry coupled with the hydride generation technique

An annular-shaped, high power nitrogen microwave induced plasma (N₂-MIP) produced at atmospheric pressure by an Okamoto cavity, as a new excitation source for atomic emission spectrometry (AES), has been used for the simultaneous determination of bismuth and tellurium in steels with the hydride generation method. Under the optimized experimental conditions, the best attainable detection limits at the Bi I 195.389 nm and Te I 200.200 nm lines were 110 and 86 ng/ml for bismuth and tellurium, respectively. The linear dynamic ranges for bismuth and tellurium were 300 to 30,000 ng/ml. The presence of several diverse elements was found to cause a more or less depressing interference with the proposed technique. When bismuth and tellurium in steels were determined, a large amount of Fe(III) in the solution caused a severe depressing interference, while the presence of Fe(II) showed little or no significant interference. Of the several interference-releasing agents examined, l-ascorbic acid was found to be the most preferable to reduce Fe(III) to Fe(II) prior to hydride generation. The concentrations of bismuth and tellurium in steels were determined by the proposed technique. The results obtained by this method were in good agreement with their certified values.     

On-line double isotope dilution laser ablation inductively coupled plasma mass spectrometry for the quantitative analysis of solid materials

We report on the determination of trace elements in solid samples by the combination of on-line double isotope dilution and laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS). The proposed method requires the sequential analysis of the sample and a certified natural abundance standard by on-line IDMS using the same isotopically-enriched spike solution. In this way, the mass fraction of the analyte in the sample can be directly referred to the certified standard so the previous characterization of the spike solution is not required. To validate the procedure, Sr, Rb and Pb were determined in certified reference materials with different matrices, including silicate glasses (SRM 610, 612 and 614) and powdered samples (PACS-2, SRM 2710a, SRM 1944, SRM 2702 and SRM 2780). The analysis of powdered samples was carried out both by the preparation of pressed pellets and by lithium borate fusion. Experimental results for the analysis of powdered samples were in agreement with the certified values for all materials. Relative standard deviations in the range of 6–21% for pressed pellets and 3–21% for fused solids were obtained from n = 3 independent measurements. Minimal sample preparation, data treatment and consumption of the isotopically-enriched isotopes are the main advantages of the method over previously reported approaches.     

Determination of nickel in finished product alloys by instrumental neutron activation analysis and spectrophotometry

Nickel contents in different finished product alloys were determined using a k ₀-based internal monostandard instrumental neutron activation analysis (IM-INAA) method. Five stainless steels (SS) and three high nickel alloys were analyzed by IM-INAA. BCS CRMs 225/1 (low alloy steel) and 466 (austenitic SS) and NIST SRM 247 (high Ni alloy) were analyzed to evaluate the accuracy of the method. The results of CRMs and SS were found to be in good agreement with certified or specified values. The Ni contents in the high nickel alloys were also determined by relative method of NAA for verification. Nickel contents in BCS CRM 466 and SS 316M were determined by UV–Visible spectrophotometry and the values were found to be in good agreement with IM-INAA results.     

Determination of Mo and Bi in steels by electrothermal atomic absorption spectrometry after complexation and sorption on activated carbon

A simple method for the preconcentration of Mo and Bi in steels is proposed. The analytes are complexed with the ammonium salt of dithiophosphoric acid O,O-diethyl ester and sorbed onto activated carbon. After desorption into a small volume of nitric acid at low pH, Mo and Bi are determined by electrothermal atomic absorption spectrometry. Iron(III) is reduced to Fe(II), which is not complexed and not significantly retained on the carbon. Enrichment factor of 23 and 26 were obtained for Mo and Bi, respectively. The method was applied to the analysis of four certified reference steels, after acid dissolution in a microwave system and good agreement was obtained with the certified or recommended values.     

Pitting inhibition of stainless steel by surfactants: an electrochemical and surface chemical approach

Pitting corrosion of stainless steels causes tremendous damage in terms of material loss and resulting accidents. Organic surfactants have been tried as pitting inhibitors but the understanding of the inhibition mechanisms is mainly speculative. In the present study the inhibition of the pitting corrosion of 304 stainless steel by N-lauroylsarcosine sodium salt (NLS) in 0.1 M NaCl solutions at neutral pH was studied using an approach that combines surface chemical techniques with electrochemical ones. It was found that NLS increases the pitting resistance of 304 stainless steel, with possible complete inhibition at high NLS concentration (30 mM). Adsorption of NLS on 304 stainless steel particles was directly measured. NLS adsorbs significantly on 304 stainless steel with maximum adsorption density close to bilayer coverage. Electrophoretic mobility data for 304 stainless steel particles show that the surface of 304 stainless steel is negative in NaCl solution at neutral pH. The adsorption of NLS makes the interfacial charge even more negative. The relationship between pitting inhibition and adsorption density of NLS suggests that NLS does not adsorb preferentially on the pit nucleation sites and complete inhibition requires that the whole surface be covered completely by NLS. The inhibition mechanism of NLS is proposed to be due mainly to the blocking effect of a negatively charged NLS adsorption layer. This study shows that in addition to the adsorption amount of surfactant, interfacial charge also plays an important role in pitting inhibition.     

亚稳态304不锈钢应力腐蚀影响因素探讨

30 4不锈钢通过低温拉伸制得含有不同马氏体相变量的试样 ,由于冷加工将不可避免地导致位错密度大幅度增加 ,利用铁素体测量仪和透射电镜 (TEM )检测并分析 30 4不锈钢位错形态 .上述试样在 4 2 %MgCl2 沸腾溶液中用慢应变速率法 (SSRT) ,结合金相显微镜 ,扫描电子显微镜等表面分析手段 ,探讨了微观组织变化对 30 4不锈钢应力腐蚀的影响 .结果表明 :由于马氏体相和位错缺陷的交互作用 ,影响了 30 4不锈钢在沸腾MgCl2 溶液中应力腐蚀敏感性 ,且在不同变形量范围内 ,影响的主导因素不同     

Direct determination of trace metals in solid samples by atomic absorption spectrometry with electrothermal atomizers: Part 4. Interference effects in the determination of lead and bismuth in steels

The origin of observed interference effects is investigated by comparing signals obtained for lead and bismuth before and after the addition of different matrix components. It is concluded that the applicability of the solid-sampling technique should be related to the solubility of the impurity in the matrix components and to the volatilities of the impurity and matrix. The extent to which trace elements are removed from steels is similarly established by using steels and graphite pieces to which the element was added. The samples are introduced under isothermal conditions and peak areas are evaluated. It is found that 80% of lead or bismuth is recovered from stainless steel at 2100°C. Thus standardization against aqueous solutions gives inaccurate results for solid samples.     

Individual sample conditioning in flow analysis. Determination of N-total in plant materials

A flow-batch system allowing in-line individual sample matrix matching is proposed for analysis of sample lots with high variability in acidity. The feasibility of the approach is demonstrated in the spectrophotometric determination of total nitrogen in Kjeldahl digests, using a column with a slightly soluble reagent (AgCl). The solutions are sequentially injected by means of an 8-port selecting valve and processed in a mixing chamber that is also used as a monitoring unit. The system yields reproducible results (r.s.d. usually < 2.5%) and the sampling rate is 14 samples/h. The analytical curve is linear within 1.00 and 6.00% N (dry basis), and the regression coefficient is > 0.999 (n = 6). Results are in agreement with certified values of standard reference materials and with results obtained by conductometry.     

Simultaneous determination of monomethylmercury, monobutyltin, dibutyltin and tributyltin in environmental samples by multi-elemental-species-specific isotope dilution analysis using electron ionisation GC-MS

In this work, the simultaneous determination of four organometallic species (monomethylmercury, monobutyltin, dibutyltin and tributyltin) in environmental samples by using a GC-MS system with electron ionisation has been established. The measurement of isotope ratios in each species was accomplished by selecting the most adequate molecular cluster, and simple mathematical equations were applied to correct the contributions of 13C from the organic groups attached to the tin and mercury atoms. The influence of different parameters such as dwell time on the precision and accuracy of the measured isotope ratios in each target species has also been studied. The determination and the sample preparation procedures presented in this work were first individually validated by analysing several certified reference materials for butyltin compounds (mussel tissue CRM-477 and marine sediment SOPH-1) and for monomethylmercury (tuna fish CRM-464) using an innovative focused microwave technology for the extraction of the species from the solid samples. Additionally, the simultaneous determination of the four species was successfully validated by obtaining quantitative recoveries in spiked natural waters and by analysing the certified reference material BCR-710 (certified in tributyltin and monomethylmercury). The values obtained in such certified tissue were fully in agreement not only with the certified mass fractions but also with the proposed indicative values for mono- and dibutyltin.     

Determination of trace amounts of chromium by atomic absorption spectrometry with a tantalum filament atomizer

The sample solution containing chromium was vaporized and atomized from a tantalum filament by electrical heating into an argon stream within an absorption chamber. The interference of various metals on the atomic absorption spectrometry of chromium was investigated. Interferences were minimized by using a high filament temperature. The flameless atomizer was used for the determination of chromium in steel at a filament temperature of 2150°; with the steels investigated no matrix effect was observed, and the accuracy and precision were satisfactory.     

Individual sample conditioning in flow analysis. Determination of N-total in plant materials

A flow-batch system allowing in-line individual sample matrix matching is proposed for analysis of sample lots with high variability in acidity. The feasibility of the approach is demonstrated in the spectrophotometric determination of total nitrogen in Kjeldahl digests, using a column with a slightly soluble reagent (AgCl). The solutions are sequentially injected by means of an 8-port selecting valve and processed in a mixing chamber that is also used as a monitoring unit. The system yields reproducible results (r.s.d. usually < 2.5%) and the sampling rate is 14 samples/h. The analytical curve is linear within 1.00 and 6.00% N (dry basis), and the regression coefficient is > 0.999 (n = 6). Results are in agreement with certified values of standard reference materials and with results obtained by conductometry. Received: 5 April 2000 / Revised: 6 June 2000 / Accepted: 13 June 2000     

Electrochemical and XPS studies on corrosion behaviours of AISI 304 and AISI 316 stainless steels under plastic deformation in sulphuric acid solution

The corrosion behaviours of austenitic stainless steels were investigated by electrochemical methods under plastic deformation with constant strain in the naturally aerated 0.5 M H₂SO₄ + 0.2 M KCl solution at room temperature. The work addresses the influence of plastic deformation and molybdenum element on the corrosion resistance of austenitic stainless steels in the test solution. Electrochemical impedance spectroscopy presents the decreasing charge transfer resistance (R_t) and polarization resistance (R_p) values with the immersion time for AISI 304 stainless steel under constant strain deformation, and the increasing R_t and R_p values with the immersion time for AISI 316 stainless steel. The analysis of the chemical composition of the corrosion products was carried out by XPS. Molybdenum addition in AISI 316 stainless steel affects significantly the corrosion resistance because of its high ability to form Mo (VI) and MoCl₅ insoluble compounds in acid medium. Copyright © 2011 John Wiley & Sons, Ltd.     

Development of a supercritical fluid extractor coupled with a time-of-flight mass spectrometer for online detection of extracts.

A combined apparatus of a supercritical CO2 extractor (SFE) and a time-of-flight mass spectrometer (TOF-MS) was developed aiming at the direct analysis of extracts. A fused-silica capillary acts as both a pressure restrictor and an effluent injection nozzle into the TOF-MS. The tip of the nozzle was narrowed by melting and abrasion so that a greater pressure drop occurred at the tip. In the TOF-MS chamber, differential pumping between the main and ionization chamber kept the pressure in the ionization chamber at around 10(-3) Pa when the SFE pressure was at 9.7 to 29.4 MPa. The TOF-MS performance, a mass resolution of 263 at m/z = 146, and a sensitivity of 1.6 ng (p-dichlorobenzene) were certified by direct injection of a standard organic solution. Online detection of SFE effluent containing naphthalene, p-dichlorobenzene, phenanthrene and pyrene were successfully performed by the TOF-MS only for 48000 ionization cycles corresponding to 7.5 s.     

Use of tandem calibration for analyzing steels and alloys by inductively coupled plasma atomic emission spectrometry

A method is proposed for plotting calibration graphs by reference analyte solutions (tandem calibration) for the analysis of steels and alloys by inductively coupled plasma atomic emission spectrometry (ICP-AES) with spark ablation. The use of spectral lines of analytes and an internal standard with similar values of sums of ionization and excitation energy ensures an excellent repeatability and accuracy of the results of analysis using tandem calibration. A nebulizer chamber for the simultaneous introduction of solutions and solid sample aerosols into inductively coupled plasma (ICP) is designed. The optimal parameters of the introduction of sample aerosols and a method of plasma observation are chosen; the requirements for the choice of the analytical lines of analytes are proposed.     

New calibration method for solid sampling Zeeman atomic absorption spectrometry (SS-ZAAS) for cadmium

Summary Calibration of solid sampling Zeeman AAS for cadmium was investigated. A series of certified reference materials was analysed using a CRM with a different composition as standard. For routine applications this yielded satisfactory results. A method of calibration was then applied involving addition of standard solution to lyophilized samples, followed by lyophilization and homogenization. Using an iteration procedure results were obtained which no longer depend on certified reference materials. The method was applied to the analysis of a testbatch of codfish powder prepared at CBNM. Finally, the spiked fish standards obtained in this way were also used to analyse other certified reference materials.     

基于电化学噪声研究模拟海洋大气环境下304不锈钢的点蚀行为

基于电化学噪声技术建立了不锈钢海洋大气点蚀监测系统,利用该系统对处于干湿循环环境下不锈钢的点蚀行为进行监测. 使用时域谱图、时域统计、频域谱图和散粒噪声理论等分析方法对采集到的电化学噪声数据进行处理分析,并结合动电位极化法,形貌分析法共同研究不锈钢的点蚀行为. 研究结果表明,304不锈钢在模拟海洋大气环境下的点蚀行为分为钝化、亚稳态点蚀和稳态点蚀三个阶段. 在钝化阶段,电位电流噪声信号出现少量的同步异向波动,腐蚀事件发生频率高,平均电量低;在亚稳态点蚀阶段,电位电流噪声信号出现大量的同步同向波动,腐蚀事件发生频率降低,平均电量上升,通过扫描电镜观察蚀点;在稳态点蚀阶段,电位电流噪声信号不仅存在大量的同步同向波动,还出现了同步异向波动,腐蚀事件发生频率较低,平均电量大幅度上升,通过扫描电镜观察到电极表面出现小而浅的蚀点. 而动电位极化法可以证实304不锈钢点蚀的发生. 两种分析方法所得结果具有较好的一致性,证明该监测系统很好地实现了对模拟海洋大气环境下304不锈钢点蚀行为的连续监测,并能判断点蚀的发生.     

The determination of cadmium in environmental samples by slurry atomization graphite furnace atomic absorption spectrophotometry using platforms and matrix modification

The conditions which allow the accurate and precise determination of cadmium in environmental samples using direct solid introduction and electrothermal atomization atomic absorption spectrometry have been investigated. Cadmium was successfully determined in three certified reference materials (an aquatic plant, olive leaves, and mussels). Utilization of platform atomization and a 0.5% solution of ammonium phosphate as matrix modifier eliminated matrix interference effects. Excellent agreement was obtained with the certified values, with precision equivalent to that found by conventional acid digestion procedures.