Electrospun non-woven nanofibrous hybrid mats based on chitosan and PLA for wound-dressing applications

Continuous defect-free nanofibers containing chitosan (Ch) or quaternized chitosan (QCh) were successfully prepared by one-step electrospinning of Ch or QCh solutions mixed with poly[(L-lactide)-co-(D,L-lactide)] in common solvent. XPS revealed the surface chemical composition of the bicomponent electrospun mats. Crosslinked Ch- and QCh-containing nanofibers exhibited higher kill rates against bacteria S. aureus and E. coli than the corresponding solvent-cast films. SEM observations showed that hybrid mats were very effective in suppressing the adhesion of pathogenic bacteria S. aureus. The hybrid nanofibers are promising for wound-healing applications.     

Permeation through homopolymer latex films

The helium permeabilities of homopolymer films cast from polymer solutions and latex dispersions have been measured as a function of time. The permeability coefficients of most polymer latex films started off at a value which was considerably higher than that of the corresponding solvent-cast film, but then dropped at a rate dependent on the polymer concerned. The permeability coefficients levelled off at a value which was closer to, but still higher than that of the equivalent solvent-cast film. Solvent-cast film permeabilities remained constant for the period of several months over which time they were examined. The reduction in the permeability of latex films is attributed to ageing processes occurring within the film after casting. The fact that latex film permeability coefficients are always higher than those of solvent-cast films suggests that latex films never become completely homogeneous. The effect on permeability of the latex type and characteristics, and preparation and storage conditions has been examined. The polymer molecular weight, particle size, and surface-change density did not appear to exert any influence, within experimental error. However, the time-dependent permeability behavior was affected by the film preparation and storage temperatures.     

Polypeptide-synthetic polymer hybrids, 1. Miscibility of poly(vinyl alcohol) with poly(sodium α,β-D,L-aspartate)

The present paper describes materials of polypeptide-commodity polymer hybrids from poly(vinyl alcohol) (PVA) and poly(sodium α,β-D ,L -aspartate) ( 1 ). Miscible blend films of polypeptide 1 and PVA were prepared by the solvent-cast method from a homogeneous aqueous solution. Differential scanning calorimetry. Fourier transform infrared, and scanning electron microscopy combined with energy dispersive X-ray spectroscopy (EDX) were used to investigate the blends. It was revealed that 1 and PVA are miscible in a wide range of compositions.     

Effect of carbon nanoparticles of different shapes on mechanical properties of aromatic polyimide-based composite films

Nanocomposite films based on thermally stable polypyromellitimide are prepared via the introduction of cylindrical and laminar carbon nanoparticles—nanofibers and nanocones/disks—into the prepolymer solution. An increase in the filler concentration increases the elastic modulus and yield stress of the material. Moreover, in composites filled with nanofibers, both characteristics increase much less intensely than those of films containing nanocones/disks. Rigidity increases in composites filled with nanofibers when their concentration is below ～7 vol %. A further increase in concentration is accompanied by the aggregation of nanofibers. The introduction of the nanoparticles of both types into the polymer matrix stabilizes the behavior of the material under prolonged mechanical loading: both the creep strain and the relaxation intensity decline with an increase in the filler concentration. The introduction of nanocones/disks into the polyimide matrix results in a more pronounced stabilization of creep characteristics of films than that in the case of nanofibers.     

Thermal,morphological, and mechanical properties of ethyl vanillin immobilized in polyvinyl alcohol by electrospinning process

In this study, polyvinyl alcohol (PVA) nanofibers with ethyl vanillin as an active compound were prepared using electrospinning technique. The final products of electrospinning process were in the form of nanofibers films. PVA/ethyl vanillin nanofibers, having fibers diameters in the range 100–1700 nm, were successfully electrospun from ethanol/water mixture of PVA and ethyl vanillin. The effects of immobilization process on ethyl vanillin thermal properties were investigated by differential scanning calorimetry (DSC). The results of DSC showed significant influence of immobilization process on thermal properties of ethyl vanillin. It was noticed that melting point of immobilized ethyl vanillin was lower (~55 °C) compared to free flavor (~77 °C). Our results showed that films based on PVA/ethyl vanillin nanofibers are mechanically stable.     

Synergistic effect of graphene oxide nanoplatelets and cellulose nanofibers on mechanical,thermal, and barrier properties of thermoplastic starch

In recent years, because of the limited availability of oil resources and the increasing concerns regarding environment protection, much attention has been drawn to produce packaging films based on degradable biopolymers instead of synthetic polymers. On the other hand, because of the high costs of oil extraction, raw materials and film production, and disposing of the waste products of synthetic films, the need to replace these films with less pollutant and more cost‐effective films is growing globally. In this study, to answer the need for replacing synthetic polymer films, nanocomposite films based on thermoplastic starch reinforced with cellulose nanofibers and graphene oxide nanoplatelets were produced and characterized. The results implied that the synergistic effect of cellulose nanofibers and graphene oxide nanoplatelets has played an important role in improving the mechanical properties of the films. The results showed that with the addition of cellulose nanofibers and graphene oxide nanoplatelets, the tensile strength and elastic modulus of starch film were increased from 3 and 32 MPa to 13 and 436 MPa, which corresponds to 438% and 1435% improvement, respectively. In addition, the oxygen permeability resistance and the water vapor transmission for samples containing 3 wt% of graphene oxide nanoplatelets was decreased by 78% and 30% compared with the thermoplastic starch film, respectively. The permeability coefficient of the samples containing 3 wt% graphene oxide nanoplatelets for oxygen, nitrogen, and carbon dioxide have proved to be 0.051, 0.054, and 0.047 barrer, which shows that these films can perform well as packaging films.     

Switchable ionic liquids enable efficient nanofibrillation of wood pulp

Use of switchable ionic liquid (SIL) pulp offers an efficient and greener technology to produce nanofibers via ultrafine grinding. In this study, we demonstrate that SIL pulp opens up a mechanically efficient route to the nanofibrillation of wood pulp, thus providing both a low cost and chemically benign route to the production of cellulose nanofibers. The degree of fibrillation during the process was evaluated by viscosity and optical microscopy of SIL treated, bleached SIL treated and a reference pulp. Furthermore, films were prepared from the fibrillated material for characterization and tensile testing. It was observed that substantially improved mechanical properties were attained as a result of the grinding process, thus signifying nanofibrillation. Both SIL treated and bleached SIL treated pulps were fibrillated into nanofibers with fiber diameters below 15 nm thus forming networks of hydrophilic nature with an intact crystalline structure. Notably, it was found that the SIL pulp could be fibrillated more efficiently than traditional pulp since nanofibers could be produced with more than 30% less energy when compared to the reference pulp. Additionally, bleaching reduced the energy demand by further 16%. The study demonstrated that this switchable ionic liquid treatment has considerable potential in the commercial production of nanofibers due to the increased efficiency in fibrillation.     

Determination of Plasticizers Commonly Used In Pharmaceutical Dosage Forms by High Performance Liquid Chromatography

Abstract

A simple reversed-phase HPLC method was developed to identify and quantify plasticizers commonly used with polymers present in sustained or controlled release dosage forms. the plasticizers investigated included triethyl citrate, tributyl citrate, acetyl triethyl citrate, dibutyl sebacate, diethyl phthalate, dibutyl phthalate, and triacetin. the plasticizers were detected at 220 nm, the mobile phase being methanol:water (70:30 v/v%). the peak area response was linear over the studied concentration range of 0.5–5.0 mM/L for triethyl citrate, acetyl triethyl citrate, dibutyl sebacate, and triacetin, and 0.005 ? 0.05 mM/L for diethyl phthalate. the recovery from solvent-cast ethyl cellulose and Eudragit RS 100 films was complete. Two pharmaceutical applications of this assay included the quantitation of plasticizers in polymer-coated sugar beads and a leaching study of a water-soluble plasticizer, triethyl citrate, from polymeric films into simulated intestinal fluids.     

Development of silver-containing nanocellulosics for effective water disinfection

Electrospun cellulose nanofibers and cellulose-graft-polyacrylonitrile (Cell-g-PAN) copolymer nanofibers containing silver nanoparticles (AgNPs) were synthesized for effective water disinfection. Surface morphology, AgNPs content, physical distribution of AgNPs, levels of silver leaching from the fibers in water and antimicrobial efficacy were studied. Scanning electron microscope images revealed that AgNPs in cellulose nanofibers were more evenly dispersed than in Cell-g-PAN copolymer nanofibers, but with the certainty that Cell-g-PAN copolymer nanofibers had higher AgNPs content. This was confirmed by energy dispersive X-ray analysis and atomic absorption analysis. Both cellulose nanofibers and Cell-g-PAN copolymer nanofibers containing AgNPs had excellent antimicrobial activity against Escherichia coli, Salmonella typhi, and Staphylococcus aureus, with cellulose-nAg nanofibers killing between 91 and 99 % of bacteria in a contaminated water sample and Cell-g-PAN-nAg copolymer nanofibers killed 100 %. Neither Cell-g-PAN copolymer nanofibers nor cellulose nanofibers leached silver into water.     

The role of nanocellulose fibers, starch and chitosan on multipolysaccharide based films

Thin nanocomposite films of thermoplastic starch, chitosan and cellulose nanofibers (bacterial cellulose or nanofibrillated cellulose) were prepared for the first time by solvent casting of water based suspensions of the three polysaccharides. The role of the different bioploymers on the final properties (thermal stability, transparency, mechanical performance and antimicrobial activity) of the films was related with their intrinsic features, contents and synergic effects resulting from the establishment of interactions between them. Thermoplastic starch displays an important role on the thermal stability of the films because it is the most stable polysaccharide; however it has a negative impact on the mechanical performance and transparency of the films. The addition of chitosan improves considerably the transparency (up to 50 % transmittance for 50 % of chitosan, in respect to the amount of starch), mechanical performance and antimicrobial properties (at least 25 % of chitosan and no more than 10 % of cellulose nanofibers are required to observe bacteriostatic or bactericidal activity) but decrease their thermal stability. The incorporation of cellulose nanofibers had the strongest positive impact on the mechanical properties of the materials (increments of up to 15 and 30 MPa on the Young′s modulus and Tensile strength, respectively, for films with 20 % of BC or NFC). Nonetheless, the impact in thermal stability and mechanical performance of the films, promoted by the addition of chitosan and cellulose nanofibres, respectively, was higher than the expected considering their percentage contents certainly because of the establishment of strong and complex interactions between the three polysaccharides.     

Effects of Geomaterial-Originated Fillers on Microstructure and Mechanical/Physical Properties of α- and β-Chitosan-Based Films

Edible films and coatings with good mechanical/physical properties are highly required for carrying medical substances and food packaging. So, solvent-cast films of α- or β-chitosan filled with palygorskite, montmorillonite or geopolymer-containing material (GCM), were prepared, and the effects of their clay contents (up to 50 wt.%) on the mechanical/physical properties were assessed. The microstructure of the films was investigated using FT-IR spectroscopy, SEM and thermal analysis. The results showed that, except for the films composed of GCM and β-chitosan, the mechanical properties of the films with limited (up to 5 wt.%) to moderate (5–25 wt.%) amounts of fillers increased as a result of the attractive electrostatic forces formed between the fillers and chitosan functional groups (–NH₃⁺, CH₂OH and NHCOCH₃). However, due to the occurrence of coarse aggregates, the strength of filler-rich films declined. The addition of fillers led to an increase in porosity and water absorption of the films, but it had irregular effects on their wettability and water vapor transmission rate. These observations as well as the thermal stability of the films were discussed in relation to the characterization results.     

Oxygen and oil barrier properties of microfibrillated cellulose films and coatings

The preparation of carboxymethylated microfibrillated cellulose (MFC) films by dispersion-casting from aqueous dispersions and by surface coating on base papers is described. The oxygen permeability of MFC films were studied at different relative humidity (RH). At low RH (0%), the MFC films showed very low oxygen permeability as compared with films prepared from plasticized starch, whey protein and arabinoxylan and values in the same range as that of conventional synthetic films, e.g., ethylene vinyl alcohol. At higher RH’s, the oxygen permeability increased exponentially, presumably due to the plasticizing and swelling of the carboxymethylated nanofibers by water molecules. The effect of moisture on the barrier and mechanical properties of the films was further studied using water vapor sorption isotherms and by humidity scans in dynamic mechanical analysis. The influences of the degree of nanofibrillation/dispersion on the microstructure and optical properties of the films were evaluated by field-emission scanning electron microscopy (FE-SEM) and light transmittance measurements, respectively. FE-SEM micrographs showed that the MFC films consisted of randomly assembled nanofibers with a thickness of 5–10 nm, although some larger aggregates were also formed. The use of MFC as surface coating on various base papers considerably reduced the air permeability. Environmental scanning electron microscopy (E-SEM) micrographs indicated that the MFC layer reduced sheet porosity, i.e., the dense structure formed by the nanofibers resulted in superior oil barrier properties.     

Pr掺杂Bi_2MoO_6/TiO_2复合纳米纤维的制备及可见光催化性能

以电纺TiO_2纳米纤维为基质,采用溶剂热法制备了稀土Pr掺杂Bi_2MoO_6/TiO_2复合纳米纤维,利用X射线衍射仪、扫描电子显微镜、透射电子显微镜、紫外-可见-近红外分光光度计和荧光光谱仪等对不同样品的物相、形貌和光学性能等进行表征,以甲基橙为模拟有机污染物,考察了样品的光催化性能.结果表明,在复合样品中,Pr~(3+)进入Bi_2MoO_6晶格,部分取代Bi~(3+)形成施主能级,导致能级带隙变窄,不仅有利于提高样品的可见光催化活性,抑制光生电子-空穴对复合,而且还提高了Bi_2MoO_6/TiO_2的光催化活性和稳定性.当Pr的掺杂量为3%(摩尔分数)时,光催化降解甲基橙的效果最佳,可见光照射180 min时降解率达到93.8%,比纯Bi_2MoO_6/TiO_2的降解率有明显提高.     

Preparation and Characterization of Polyhydroxyalkanoates Macroporous Scaffold Through Enzyme-Mediated Modifications

Polyhydroxyalkanoates (PHAs) are hydrophobic biodegradable thermoplastics that have received considerable attention in biomedical applications due to their biocompatibility, mechanical properties, and biodegradability. In this study, the degradation rate was regulated by optimizing the interaction of parameters that influence the enzymatic degradation of P(3HB) film using response surface methodology (RSM). The RSM model was experimentally validated yielding a maximum 21 % weight loss, which represents onefold increment in percentage weight loss in comparison with the conventional method. By using the optimized condition, the enzymatic degradation by an extracellular PHA depolymerase from Acidovorax sp. DP5 was studied at 37 °C and pH 9.0 on different types of PHA films with various monomer compositions. Surface modification of scaffold was employed using enzymatic technique to create highly porous scaffold with a large surface to volume ratio, which makes them attractive as potential tissue scaffold in biomedical field. Scanning electron microscopy revealed that the surface of salt-leached films was more porous compared with the solvent-cast films, and hence, increased the degradation rate of salt-leached films. Apparently, enzymatic degradation behaviors of PHA films were determined by several factors such as monomer composition, crystallinity, molecular weight, porosity, and roughness of the surface. The hydrophilicity and water uptake of degraded salt-leached film of P(3HB-co-70%4HB) were enhanced by incorporating chitosan or alginate. Salt-leached technique followed by partial enzymatic degradation would enhance the cell attachment and suitable for biomedical as a scaffold.     

Electrophoretic deposition of polyaniline nanofibers on a stainless steel wire as an adsorbent for determination of tamoxifen by SPME/GC–FID in urine samples

Polyaniline nanofiber films were fabricated on the surface of stainless steel wire via a controllable and simple electrophoretic deposition route from a nonaqueous colloidal suspension consisting of polyaniline nanofibers. The prepared coating material was then characterized by field emission scanning electron microscopy equipped with energy dispersive spectroscopy and elemental mapping analysis. The fabricated polyaniline film-coated stainless steel wire was then utilized as an effective and novel sorbent phase for solid-phase microextraction of tamoxifen for subsequent gas chromatography/flame ionization detection of this anticancer drug. Parameters consisting of the temperature, extraction time, salt concentration, agitation speed, pH, temperature and time of desorption were studied and optimized using a one-at-a-time strategy. Under the optimum conditions, detection limit (S/N = 3), the limit of quantification (10/3 limit of detection), linear dynamic range, repeatability and reproducibility values of 0.51 μg L⁻¹, 1.7 μg L⁻¹, 2–1,130 μg L⁻¹, 5.7% and 8.6% were attained, respectively. The prepared fiber can preserve 90% of its efficacy after 20 consecutive cycles, demonstrating the suitable thermal stability and cyclability of the proposed solid-phase microextraction coating material for the determination of tamoxifen by gas chromatography/flame ionization detection. The route was effectively utilized to determine tamoxifen in urine samples, with relative recoveries ranging from 89 to 106%.     

Bioactive Pectin-Murta (Ugni molinae T.) Seed Extract Films Reinforced with Chitin Fibers

This study investigated the biocomposite pectin films enriched with murta (Ugni molinae T.) seed polyphenolic extract and reinforced by chitin nanofiber. The structural, morphological, mechanical, barrier, colorimetric, and antioxidant activity of films were evaluated. The obtained data clearly demonstrated that the addition of murta seed extract and the high load of chitin nanofibers (50%) provided more cohesive and dense morphology of films and improved the mechanical resistance and water vapor barrier in comparison to the control pectin film. The antioxidant activity ranged between 71% and 86%, depending on the film formulation and concentration of chitin nanofibers. The presented results highlight the potential use of chitin nanofibers and murta seed extract in the pectin matrix to be applied in functional food coatings and packaging, as a sustainable solution.     

Preparation,characterization, and properties of nanofibers based on poly(vinylidene fluoride) and polyhedral oligomeric silsesquioxane

Nanostructered nanofibers based on poly(vinylidene fluoride) (PVDF) and polyhedral oligomeric silsesquioxane (POSS) have been prepared by electrospinning process. The starting solutions were prepared by dissolving both the system components in the mixture N,N‐dimethylacetamide/acetone. The characteristics of the fiber prepared, studied by scanning electron microscopy, atomic force microscopy, and wide angle X‐ray diffraction, have been compared with those of PVDF fibers. Morphological characterization has demonstrated the possibility to obtain defect‐free PVDF/POSS nanofibers by properly choosing the electrospinning conditions, such as voltage, polymer concentration, humidity, etc. Conversely, in the case of fibers based on the neat polymer, it was not possible to attain the complete elimination of beads in the electrospun nanofibers. The different behavior of the two types of solutions has been ascribed to silsesquioxane molecules, which, without influencing the solution viscosity or conductivity, favor the formation of uniform structures by decreasing the system surface tension. Concerning POSS distribution in the fibers, the morphological characterization of the electrospun films has shown a submicrometric dispersion of the silsesquioxane. It is relevant to underline that cast films, prepared by the same solutions, have been found to be characterized by POSS aggregation, thus demonstrating a scarce affinity between the two‐system components. Indeed, the peculiar solvent evaporation of the electrospun solution, which is much faster than that occurring during the cast process, prevents POSS aggregation, thus leading to the formation of nanofibers characterized by a silsesquioxane dispersion similar to that present in solution. Finally, the presence of POSS improves the electrospun film mechanical properties. Copyright © 2011 John Wiley & Sons, Ltd.     

In vitro biocompatibility of electrospun and solvent-cast chitosan substrata towards Schwann, osteoblast, keratinocyte and fibroblast cells

Chitosan or poly(N-acetyl-d-glucosamine-co-d-glucosamine) with a degree of deacetylation of about 85% was fabricated into nanofibrous membranes by electrospinning from 7% w/v chitosan solution in 70:30 v/v trifluoroacetic acid/dichloromethane solvent system. The obtained fibers were smooth without the presence of beads. The diameters of the individual fiber segments were 126 ± 20 nm. The potential for use of the electrospun chitosan nanofibrous membranes as substrates for cell/tissue culture was evaluated with four different cell types, i.e., Schwann cells, osteoblast-like cells, keratinocytes and fibroblasts, in terms of the attachment and the proliferation of the cells as well as the morphology of the seeded and the cultured cells. The results were compared with the corresponding solvent-cast films. Both types of the chitosan substrates supported the attachment and, at the same time, promoted the largest increase in the viability of the cultured keratinocytes. The viability of Schwann cells cultured on these substrates increased marginally well, but the attachment of the cells on the surfaces was relatively poor. Finally, both types of the chitosan substrates showed cytostatic property towards both osteoblast-like cells and fibroblasts, despite the convincingly good attachment of osteoblast-like cells on the surfaces.     

Preparation and characterization of cellulose nanocomposite films with two different organo-micas

The mechanical properties, morphologies, and gas barriers of hybrid films of cellulose with two different organoclays are compared. Dodecyltriphenyl-phosphonium-mica (C₁₂PPh-mica) and hexadecyl-mica (C₁₆-mica) were used as reinforcing fillers in the fabrication of the cellulose hybrid films. The cellulose hybrid films were synthesized from N-methyl-morpholine-N-oxide (NMMO) solutions with the two organo-micas, and solvent-cast at room temperature under vacuum, yielding 15–20 μm thick films of cellulose hybrids with various clay contents. We found that the addition of only a small amount of organoclay is sufficient to improve the mechanical properties and gas barriers of the cellulose hybrid films. Even polymers with low organoclay contents (1–7 wt %) were found to exhibit much higher strength and modulus values than pure cellulose. The addition of C₁₂PPh-mica was more effective than that of C₁₆-mica with regards to the initial tensile modulus, whereas the addition of C₁₆-mica was more effective than that of C₁₂PPh-mica with regards to the gas barrier of the cellulose matrix. The intercalations of the polymer chains in the clays were examined with wide-angle X-ray diffraction (XRD) and electron microscopy (SEM and TEM).