Thermosetting polymers from epoxy resin and a Nickel catalyst of diethylenetriamine

The kinetics and mechanism of cure reaction of DGEBA using a chelate of Ni(II) with diethylenetriamine (dien), Ni(dien)₂I_2, as a curing agent was studied by DSC. TG curve of the complex curing agent showed mass loss in two region of temperature: 200–320 and 450–550 °C. Dynamic DSC measurements showed only one exothermic peak with a maximum about 250 °C depending on the heating rate. According to the methods of KAS and Ozawa–Flynn–Wall the values of E _a were 92.5 and 96.2 kJ/mol, respectively. The isoconversional kinetic analysis in whole range of conversion, α = 0.02–0.95, showed small changes in the E _a values in the region of α = 0.04–0.6 and most likely represent some average values (E _a = 110 kJ/mol) between the values of E _a of non-autocatalyzed and autocatalyzed reactions. Using the sole dependence of E _a on α, the time required to reach fully cured materials under isothermal conditions were also predicted and compared with the experimental results.     

Studies on curing kinetics of a novel combined liquid crystalline epoxy containing tetramethylbiphenyl and aromatic ester‐type mesogenic group with diaminodiphenylsulfone

The curing kinetics of a novel liquid crystalline epoxy resin with combining biphenyl and aromatic ester‐type mesogenic unit, diglycidyl ether of 4,4′‐bis(4‐hydroxybenzoyloxy)‐3,3′,5,5′‐tetramethyl biphenyl (DGE‐BHBTMBP), and the curing agent diaminodiphenylsulfone (DDS) was studied using the advanced isoconvensional method (AICM). DGE‐BHBTMBP/DDS curing system was investigated the curing behavior by means of differential scanning calorimetry (DSC) during isothermal and nonisothermal processes. Only one exothermal peak appeared in isothermal DSC curves. A variation of the effective activation energy with the extent of conversion was obtained by AICM. Three different curing stages were confirmed. In the initial curing stage, the value of E_a is dramatically decreased from ～90 to ～20 kJ/mol in the conversion region 0–0.2 for the formation of LC phase. In the middle stage, the value of E_a keeps about ～80 kJ/mol for cooperative effect of reaction mechanism and diffusion control. In the final stage, a significant increase of E_a from 84 to 136 kJ/mol could be caused by the mobility of longer polymer chains. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3922–3928, 2007     

Cure behavior of diglycidylether of bisphenol A/trimethylolpropane triglycidylether epoxy blends initiated by thermal latent catalyst

Cure behaviors of diglycidylether of bisphenol A (DGEBA)/trimethylolpropane triglycidylether (TMP) epoxy blends initiated by 1 wt % N‐benzylpyrazinium hexafluoroantimonate (BPH) as a cationic latent catalyst were investigated using DSC and rheometer. This system showed more than one type of reaction and BPH could be excellent thermal latent catalyst without any co‐initiator. The cure activation energy (E_a) obtained from Kissinger method using dynamic DSC data was higher in DGEBA/TMP mixtures than in pure DGEBA. Rheological properties of the blend system were investigated under isothermal condition using a rheometer. The gel time was obtained from the analysis of storage modulus (G′), loss modulus (G″) and damping factor (tanδ). The crosslinking activation energy (E_c) was also determined from the Arrhenius equation based on the gel time and curing temperature. As a result, the crosslinking activation energy showed a similar behavior with that obtained from Kissinger method. And the gel time decreased with increasing TMP content, which could be resulted from increasing the activated sites by trifunctional epoxide groups and decreasing the viscosity of DGEBA/TMP epoxy blend in the presence of TMP. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2114–2123, 2000     

Thermal stability and toughening of epoxy resin with polysulfone resin

The cure behavior, thermal stability, and mechanical properties of diglycidylether of bisphenol A (DGEBA)/polysulfone (PSF) blends initiated by 1 wt % N‐benzylpyrazinium hexafluoroantimonate as a cationic latent catalyst were investigated. The DGEBA/PSF content was varied within 100/0–100/40 wt %. Latent properties were studied through the measurement of the conversion as a function of the curing temperature, and the cure activation energy (E_a) was studied by the Kissinger method with a dynamic differential scanning calorimetry analysis. The thermal stabilities, largely based on the integral procedural decomposition temperature (IPDT) and decomposed activation energy (E_t), were investigated by the measurement of thermogravimetric analysis. For the mechanical properties of the casting specimens, the critical stress intensity factor (K_IC) test was performed, and their fractured surfaces were examined with scanning electron microscopy. E_a, IPDT, E_t, and K_IC increased with PSF increasing in the neat epoxy resin up to 30 wt %. However, there was a marginal decrease in the blend system in both the thermal and mechanical properties due to the phase separation between DGEBA and PSF. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 121–128, 2001     

Quantitative studies on furfural and organic acid formation during hydrothermal,acidic and alkaline degradation ofD-xylose

Summary Chromatographic analysis of the degradation ofD-xylose either in plain water or aqueous sulfuric acid at temperatures ranging from 180 – 220°C gave up to 50 mol% of furfural. Activation energies did not differ significantly between reactions in plain water (E _a =119.4 kJ/mol), 0.001M H₂SO₄ (E _a =120.6 kJ/mol), 0.01M H₂SO₄ (E _a =130.8 kJ/mol), and 0.1M H₂SO₄ (E _a =120.7 kJ/mol). However, under alkaline conditions the activation energy was only 63.7 kJ/mol, indicating a different reaction mechanism. Isotachophoretic analyses revealed the formation of pyruvic, formic, glycolic, lactic, and acetic acid. While the relative yields of these acids ranged from 0.8 to 7% under hydrothermal and acidic conditions, 10 – 23% were obtained in alkaline degradation.

---

Quantitative Studien zur Bildung von Furfural und organischen Säuren während des hydrothermalen, sauren und alkalischen Abbaues vonD-Xylose

Zusammenfassung Die chromatographische Analyse des Abbaues vonD-Xylose in reinem Wasser und Schwefelsäure bei Temperaturen von 180 – 220°C ergab die Bildung von bis zu 50 mol% Furfural. In bezug auf die Aktivierungsenergie zeigten sich keine signifikanten Unterschiede zwischen dem Abbau vonD-Xylose in reinem Wasser (E _a =119.4 kJ/mol), 0.001M H₂SO₄ (E _a =120.6 kJ/mol), 0.01M H₂SO₄ (E _a =130.8 kJ/mol), and 0.1M H₂SO₄ (E _a =120.7 kJ/mol). Unter alkalischen Bedingungen hingegen betrug die Aktivierungsenergie nur 63.7 kJ/mol. Dies weist auf einen unterschiedlichen Reaktionsmechanismus hin. Ferner konnte mittels Isotachophorese die Bildung von Brenztraubensäure, Ameisensäure, Glycolsäure, Milchsäure und Essigsäure nachgewiesen werden. Während sich die relativen Ausbeuten in Wasser und Schwefelsäure zwischen 0.8 und 7% bewegten, betrugen sie unter alkalischen Bedingungen 10 bis 23%.

     

Synthesis and nonisothermal reaction of a novel acrylonitrile-capped poly(propyleneimine) dendrimer with epoxy resin

A novel acrylonitrile-capped poly(propylene imine) dendrimer (PAN4) was synthesized and characterized with FTIR and ¹H-NMR. PAN4 and its precursor (poly(propylene imine) dendrimer (1.0GPPI) were employed to cure bisphenol A epoxy resin (DGEBA), and the nonisothermal reaction kinetics of DGEBA/PAN4 and DGEBA/1.0GPPI was systematically investigated using a differential scanning calorimeter (DSC) in a comparative way. The apparent activation energies determined with the Kissinger method were 59.7 kJ/mol for DGEBA/1.0GPPI and 53.9 kJ/mol for DGEBA/PAN4. Applied the Málek method, it was found that a two-parameter autocatalytic model (SB(m, n)) could well simulate the reaction rates, and further analysis of the reaction rate constants showed PAN4 could cure DGEBA at a greatly decreased rate by a factor a more than ten compared with 1.0GPPI control.     

Isothermal cure kinetics of epoxy/phenol‐novolac resin blend system initiated by cationic latent thermal catalyst

The investigation of the cure kinetics of a diglycidyl ether of bisphenol A (DGEBA)/phenol‐novolac blend system with different phenolic contents initiated by a cationic latent thermal catalyst [N‐benzylpyrazinium hexafluoroantimonate (BPH)] was performed by means of the analysis of isothermal experiments using a differential scanning calorimetry (DSC). Latent properties were investigated by measuring the conversion as a function of curing temperature using a dynamic DSC method. The results indicated that the BPH in this system for cure is a significant thermal latent initiator and has good latent thermal properties. The cure reaction of the blend system using BPH as a curing agent was strongly dependent on the cure temperature and proceeded through an autocatalytic kinetic mechanism that was accelerated by the hydroxyl group produced through the reaction between DGEBA and BPH. At a specific conversion region, once vitrification took place, the cure reaction of the epoxy/phenol‐novolac/BPH blend system was controlled by a diffusion‐control cure reaction rather than by an autocatalytic reaction. The kinetic constants k₁ and k₂ and the cure activation energies E₁ and E₂ obtained by the Arrhenius temperature dependence equation of the epoxy/phenol‐novolac/BPH blend system were mainly discussed as increasing the content of the phenol‐novolac resin to the epoxy neat resin. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2945–2956, 2000     

A model study for coatings containing hexamethoxymethylmelamine

Using a model reaction we have studied the crosslinking chemistry of hydroxy-functional polymers and hexamethoxymethylmelamine. The transetherification of optically active monofunctional alcohols and hexamethoxymethylmelamine was monitored with polarimetry and ¹H-NMR. The reaction rate constants for both the forward (k₁) and the backward (k_?1) reaction of the sulphonic-acid-catalyzed alcoholysis were determined. Primary and secondary alcohols showed the same reaction rate and activation energy (E_a = 96 kJ/mol) for the forward reaction. However, the backward reaction in the equilibrium is considerably slower for primary alcohols than for secondary alcohols, with activation energies of E_a = 96 and 79 kJ/mol, respectively. When amine salts of sulphonic acids are used as catalysts, the E_a is increased from 97 to 116 kJ/mol in the case of primary alcohols. In concentrated aprotic solutions the reaction order in acid is 2.5. The same order in acid is found for the alcoholysis of acetaldehyde diethyl acetal. All the results strongly support the statement that the crosslinking reaction proceeds by an Sn-1 mechanism. The results of this model study are compared with results obtained in network-forming reactions. The important role of the evaporation of the condensation product methanol is discussed.     

Curing kinetics of bio-based epoxy resin-toughened DGEBA epoxy resin blend

In the present study, TEIA bioresin was blended with the diglycidyl ether bisphenol A (DGEBA) epoxy resin in different ratios (i.e. 10, 20, 30, 40 mass%), cured with methylhexahydrophthalic anhydride curing agent in the presence of 2-methylimidazole catalyst. The optimized composition of DGEBA and TEIA bioresin blends system was employed as an adhesive strength. The adhesive strength of the TEIA-modified DGEBA epoxy resin blend system was increased from 4.14 to 6.31 MPa on an aluminium substrate compared to the DGEBA epoxy resin. The curing kinetics of non-isothermal, DGEBA epoxy resin and its bio-based blend systems were investigated employing differential scanning calorimetry. An increase in the peak temperature and reduction in a heat of curing as well as activation energy in DGEBA epoxy resin were observed with the addition of TEIA bioresin content. The activation energy (E_a) of the DGEBA resin and their bio-based blend system were obtained from Kissinger and Flynn–Wall–Ozawa methods.

     

Dielectric relaxation analysis of starch oligomers and polymers with respect to their chain length

Starch belongs to the polyglucan group. This type of polysaccharide shows a broad β-relaxation process in dielectric spectra at low temperatures, which has its molecular origin in orientational motions of sugar rings via glucosidic linkages. This chain dynamic was investigated for α(1,4)-linked starch oligomers with well-defined chain lengths of 2, 3, 4, 6, and 7 anhydroglucose units (AGUs) and for α(1,4)-polyglucans with average degrees of polymerization of 5, 10, 56, 70, and so forth (up to 3000; calculated from the mean molecular weight). The activation energy (E_a) of the segmental chain motion was lowest for dimeric maltose (E_a = 49.4 ± 1.3 kJ/mol), and this was followed by passage through a maximum at a degree of polymerization of 6 (E_a = 60.8 ± 1.8 kJ/mol). Subsequently, E_a leveled off at a value of about 52 ± 1.5 kJ/mol for chains containing more than 100 repeating units. The results were compared with the values of cellulose-like oligomers and polymers bearing a β(1,4)-linkage. Interestingly, the shape of the E_a dependency on the chain length of the molecules was qualitatively the same for both systems, whereas quantitatively the starch-like substances generally showed higher E_a values. Additionally, and for comparison, three cyclodextrins were measured by dielectric relaxation spectroscopy. The ringlike molecules, with 6, 7, and 8 α(1,4)-linked AGUs, showed moderately different types of dielectric spectra. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 188–197, 2004     

Synthesis and cure kinetics of diphenyl(diphenylethynyl)silane monomer

Diphenyl(diphenylethynyl)silane ((ph–C≡C)₂–Si–ph₂) (DPDPES) was synthesized by the Grignard reaction. The corresponding isothermal and non-isothermal cure kinetics of DPDPES were analyzed by using differential scanning calorimetry (DSC), and the molecular structure was characterized by H-NMR. The results showed that all the cure curves were typically sigmoid shape and cure reactions could be described by an autocatalytic kinetic model by isothermal DSC. The kinetic data, for example, activation energy (E) and frequency factor (A), were 119.22 kJ/mol and 4.67 × 10⁷ (s^?1), respectively. The non-isothermal DSC analyses showed that E and A were 162.12 kJ/mol and 1.32 × 10⁹ (s^?1), respectively, and the reaction order was 0.94. Based on the research work of this paper, it can be said that the cure reaction of DPDPES monomer was of autocatalytic and diffusion-controlled characteristics, and the effect of the diffusion was more evident at low temperature. The cure reaction of DPDPES was a first-order kinetic reaction.     

Rheologic studies on chemical cross-linking kinetics for LDPE

Crosslinking reaction of LDPE resin in the presence of dicumyl peroxide(DCP) was studied by isothermal rheological measurements at different temperatures and non-isothermal differential scanning calorimetry(DSC) technique with different heating rates.The kinetic parameters of crosslinking reaction were calculated by both rheological and DSC measurements.The results reveal that with the increase of DCP contents,the apparent activation energy,E_a,ranges from about 140 kj/mol to 170 kj/mol and the order of crosslinking reaction,n,approaches unity.The influence of measurement frequency,ω,on crosslinking reaction was also investigated.It can be found that n does not change with the increase ofω, and E_a decreases slightly with the increase ofω.     

Evaluating a four-directional benzene-centered aliphatic polyamine curing agent for epoxy resins

A four-directional benzene-centered aliphatic polyamine, MXBDP, with high functionality and low volatility, is used to cure epoxy resin (DGEBA). Herein we originally report the isothermal cure kinetics and dynamic mechanical properties of DGEBA/MXBDP. Differential scanning calorimetry confirms that MXDBP is more reactive than commercial linear metaxylenediamine and branched Jeffamine T-403 and the isothermal curing reaction is autocatalytic. The Kamal model is found to be able to well describe the curing rate up to the onset of diffusion control, and the excellent match over the whole conversion range is achieved using the extended Kamal model. Interestingly, the isoconversional kinetic analysis indicates that the effective reaction activation energy (E _α ) changes substantially with conversion, and ultimately decreases to a very small value (<10 kJ mol^?1) because of the diffusion-controlled reaction kinetics. Then, dynamic mechanical analysis reveals that DGEBA/MXBDP exhibits the higher α- and β-relaxation temperatures and the much higher crosslink density than DGEBA/metaxylenediamine. Our experiment results support that MXBDP has the high reactivity and improved thermal resistance in combination with the advantages of the high functionality, low volatility and decreased CO₂ absorption. Therefore, MXBDP may be especially suitable for room temperature-cure epoxy coatings and adhesives.     

Effects of temperature on the weathering lifetime of coated polycarbonate

The lifetime of polycarbonate (PC) coated with silicone hardcoats containing UV absorber is shorter at elevated temperatures. The activation energy (E_a) for delamination was found to be 18 ± 2 kJ/mol (4.3 ± 0.5 kcal/mol) at the 95% confidence level in this study. This E_a is the consequence of the sensitivity of the substrate and the UV absorber to temperature. The E_a for PC photodegradation was previously found to be 17-21 kJ/mol (4-5 kcal/mol). The E_a for loss of absorbance in the second-generation silicone hardcoat was found to be 28.5 ± 5.4 kJ/mol (6.8 ± 1.3 kcal/mol) at the 95% confidence level. Results are consistent with experimental findings when these activation energies are used in published predictive models. Since the E_a for coating delamination depends on the E_a of UV absorber loss, coating systems different from the one in this study will need to be investigated separately.     

Curing reaction of <Emphasis Type="Italic">o</Emphasis>-cresol-formaldehyde epoxy/LC epoxy(<Emphasis Type="Italic">p</Emphasis>-PEPB)/anhydride(MeTHPA)

The curing kinetics of a bi-component system about o-cresol-formaldehyde epoxy resin (o-CFER) modified by liquid crystalline p-phenylene di[4-(2,3-epoxypropyl) benzoate] (p-PEPB), with 3-methyl-tetrahydrophthalic anhydride (MeTHPA) as a curing agent, were studied by non-isothermal differential scanning calorimetry (DSC) method. The relationship between apparent activation energy E _a and the conversion α was obtained by the isoconversional method of Ozawa. The reaction molecular mechanism was proposed. The results show that the values of E _a in the initial stage are higher than other time, and E _a tend to decrease slightly with the reaction processing. There is a phase separation in the cure process with LC phase formation. These curing reactions can be described by the Šesták–Berggren (S–B) equation, the kinetic equation of cure reaction as follows: \frac\textda\textdt = Aexp( - \fracE_\texta RT )a^m ( 1 - a )ⁿ {\frac{{{\text{d}}\alpha }}{{{\text{d}}t}}} = A\exp \left( { - {\frac{{E_{\text{a}} }}{RT}}} \right)\alpha^{m} \left( {1 - a} \right)^{n} .     

Hydrogen bond effect of azido polyurethane elastomer by dynamic mechanical analysis

Hydrogen bond effects in azido polyurethane elastomers (APUE) have been studied by dynamic mechanical analysis (DMA) and the results show that the hydrogen bond effect has stronger temperature dependence. The activation energy of hydrogen bond dissociation (E_a) and the hydrogen bond density (vs/V) have been evaluated from the elastic modulus–temperature relationship. The calculated E_a in this work is much higher than the reported values of normal polyurethane elastomer (PUE). The values of E_a are 81.3, 68.1, 53.3, and 42.3 kJ/mol at 150, 110, 50, and 20 Hz, respectively, for PUE‐1 (CPPB/HDI trimer elastomer); 94.6, 75.8, 48.4, and 36.9 kJ/mol at 150, 110, 50, and 20 Hz, respectively, for PUE‐2 (APPB/HDI trimer elastomer); 82.1, 74.4, 59.8, and 46.5 kJ/mol at 150, 110, 50, and 20 Hz, respectively, for PUE‐3 (APPB/HDI trimer/EG elastomer); 145, 124, 88.0, and 75.5 kJ/mol at 150, 110, 50, and 20 Hz, respectively, for PUE‐4 (APPB/HDI trimer/BD elastomer); and 72.2, 64.3, 49.8, and 39.9 KJ/mol at 150, 110, 50, and 20 Hz, respectively, for PUE‐5 (APPB/HDI trimer/HD elastomer). The DMA estimations are semiquantitative for it ignores other physical crosslinking effects and the results give relative order of vs/V and E_a. The values of vs/V of crosslinked APUE (PUE‐3, PUE‐4, and PUE‐5) are much higher than PUE‐2. The test frequency could affect the values of vs/V and higher frequency would minify the difference of the values of vs/V for two given temperatures. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2841–2851, 2006     

Reactions of heterocumulenes with organometallic reagents: XIII. Quantum-chemical study on the mechanisms of syn -( Z )/ anti -( E )-isomerization of methyl 2-methoxy- N -methylbuta-2,3-dienimidothioate

Mechanisms of syn-(Z)/anti-(E) isomerization of methyl 2-methoxy-N-methylbuta-2,3-dienimidothioate, including rotational, inversion, promoted by N-protonation, and nucleophile-catalyzed, were studied by quantum-chemical methods, and the corresponding thermodynamic and kinetic parameters were calculated. The most probable mechanisms of isomerization of buta-2,3-dienimidothioates were found to be inversion (E _a = 74.4 kJ/mol) and nucleophile-catalyzed (E _a = 61.6 kJ/mol). Original Russian Text ? V.A. Shagun, N.A. Nedolya, 2007, published in Zhurnal Organicheskoi Khimii, 2007, Vol. 43, No. 11, pp. 1591–1600. For communication XII, see [1].     

Kinetics of the reaction ofN-2,6-trichlorobenzoquinonimine with sodium thiosulphate

The reaction ofN-2,6-trichlorobenzoquinonimine with sodium thiosulphate has been studied in aqueous solutions. The reaction follows second-order kinetics atpH 4.62.E _a , G and S being 6.2, 21.4 kcal/mol (26,90 kJ/mol) and –53.0 eu, respectively. The rate is acid catalyzed. The results are discussed in terms of nucleophilic addition of the thiosulphate ion.

---

Kinetik der Reaktion vonN-2,6-Trichlorbenzochinonimin mit Natriumthiosulfat

Zusammenfassung Die Reaktion ist säurekatalysiert und folgt einer Kinetik zweiter Ordnung mit Werten vonE _a =6,2 kcal/mol (26 kJ/mol), G=21,4 kcal/mol (90 kJ/mol) und S=–53 eu beipH 4,62. Die Ergebnisse werden auf der Basis einer nucleophilen Addition des Thiosulfat-ions diskutiert.

     

Isothermal cure kinetics of uncatalyzed and catalyzed diglycidyl ether of bisphenol-A/carboxylated polyester hybrid powder coating

The thermal cure behavior of diglycidyl ether bisphenol-A/carboxylated polyester hybrid powder coating system in the absence and presence of catalyst was monitored using differential scanning calorimetry. Curing temperatures were between 160 and 200?°C. The experimental results showed an autocatalytic behavior of the reaction, which could be described by the model proposed by Kamal. This model includes two rate constants k ₁ and k ₂ and two reaction orders m and n. The activation energies E _a1 and E _a2 of these rate constants were 51.7 and 42.3?kJ/mol for uncatalyzed cure reaction and 40.6 and 35.0?kJ/mol for externally catalyzed reaction. The average order of the overall reaction was found to be 2.45 and 2.72 for uncatalyzed and catalyzed system, respectively. Except for the late stage of cure reaction, the model agreed well with the experimental data, especially at high temperatures and in externally catalyzed cure reaction. A diffusion factor was introduced into the model to account for the effect of diffusion on the cure rate. The modified model greatly improved the predicated data at the late stage of cure reaction.     

Thermochemical Properties and Decomposition Kinetics of Ammonium Magnesium Phosphate Monohydrate

Ammonium magnesium phosphate monohydrate NH4MgPO4·H2O was prepared via solid state reaction at room temperature and characterized by XRD, FT-IR and SEM. Thermochemical study was performed by an isoperibol solution calorimeter, non-isothermal measurement was used in a multivariate non-linear regression analysis to determine the kinetic reaction parameters. The results show that the molar enthalpy of reaction above is （28.795 ± 0.182） kJ/mol （298.15 K）, and the standard molar enthalpy of formation of the title complex is （-2185.43 ± 13.80） kJ/mol （298.15 K）. Kinetics analysis shows that the second decomposition of NH4MgPO4·H2O acts as a double-step reaction： an nth-order reaction （Fn） with n=4.28, E1=147.35 kJ/mol, A1=3.63×10^13 s^-1 is followed by a second-order reaction （F2） with E2=212.71 kJ/mol, A2= 1.82 × 10^18 s^-1.