Life test of DMFC using poly(ethylene glycol)bis(carboxymethyl)ether plasticized PVA/PAMPS proton-conducting semi-IPNs

A novel, low-cost proton-conducting semi-IPN has been successfully prepared from PVA/PAMPS blends by incorporating poly(ethylene glycol)bis(carboxymethyl)ether (PEGBCME) as a novel plasticizer. Although, the polymer is based on a relatively low content of PAMPS as a component of ion conducting sites, the resulting semi-IPN exhibited high proton conductivity (0.1 S cm⁻¹) at 25 °C, which afforded a higher power density of 51 mW cm⁻² at 80 °C. A striking feature is that a long-term initial performance is achieved with a 130 h of stable fuel cell operation in DMFC mode due to effectively suppressed methanol crossover. This is a new record for a fully hydrocarbon membrane in DMFC, seeing that the PVA–PAMPS proton-conducting semi-IPNs are made simply of aliphatic skeletons.     

Pervaporation separation of water–acetic acid mixtures through poly(vinyl alcohol)-silicone based hybrid membranes

Hybrid membranes were prepared using poly(vinyl alcohol) (PVA) and tetraethylorthosilicate (TEOS) via hydrolysis followed by condensation. The obtained membranes were characterized by Fourier transform infrared spectroscopy, wide-angle X-ray diffraction and differential scanning calorimetry. The remarkable decrease in degree of swelling was observed with increasing TEOS content in membranes and is attributed to the formation of hydrogen and covalent bonds in the membrane matrix. The pervaporation performance of these membranes for the separation of water–acetic acid mixtures was investigated in terms of feed concentration and the content of TEOS used as crosslinking agent. The membrane containing 1:2 mass ratio of PVA and TEOS gave the highest separation selectivity of 1116 with a flux of 3.33 × 10⁻² kg/m² h at 30 °C for 10 mass% of water in the feed. Except for membrane M-1, the observed values of water flux are close to the values of total flux in the investigated composition range, signifying that the developed membranes are highly water selective. From the temperature dependence of diffusion and permeation values, the Arrhenius apparent activation parameters have been estimated. The resulting activation energy values, obtained for water permeation being lower than those of acetic acid permeation values, suggest that the membranes have higher separation efficiency. The activation energy values calculated for total permeation and water permeation are close to each other for all the membranes except membrane M-1, signifying that coupled-transport is minimal as due to higher selective nature of membranes. Further, the activation energy values for permeation of water and diffusion of water are almost equivalent, suggesting that both diffusion and permeation contribute almost equally to the pervaporation process. The negative heat of sorption values (ΔH_s) for water in all the membranes suggests the Langmuir's mode of sorption.     

Pervaporation separation of aromatic/aliphatic hydrocarbons by crosslinked poly(methyl acrylate-co-acrylic acid) membranes

Copolymers of methyl acrylate and acrylic acid were synthesized to fabricate membranes ionically crosslinked using aluminum acetylacetonate for the separation of toluene/i-octane mixtures by pervaporation at high temperatures. The formation of the ionic crosslinking via bare aluminum cations was characterized by UV–VIS spectroscopy and solubility tests. Reproducibility and the reliability of the methodology for membrane formation and crosslinking were confirmed. The effects of acrylic acid content, crosslinking conditions, pervaporation temperature, and feed composition on the normalized flux and the selectivity for toluene/i-octane mixtures were determined. A typical crosslinked membrane showed a normalized flux of 26 kg μm m⁻² h⁻¹ and a selectivity of 13 for a 50/50 wt.% feed mixture at 100°C. The pervaporation properties including solubility selectivity and diffusivity selectivity are discussed in terms of swelling behavior. The performance of the current membranes were benchmarked against other membrane materials reported in the literature.     

Proton transport properties of poly(aspartic acid) with different average molecular weights

We synthesized seven partially protonated poly(aspartic acids)/sodium polyaspartates (P-Asp) with different average molecular weights to study their proton transport properties. The number-average degree of polymerization (DP) for each P-Asp was 30 (P-Asp30), 115 (P-Asp115), 140 (P-Asp140), 160 (P-Asp160), 185 (P-Asp185), 205 (P-Asp205), and 250 (P-Asp250). The proton conductivity depended on the number-average DP. The maximum and minimum proton conductivities under a relative humidity of 70% and 298 K were 1.7 · 10^?3 S cm^?1 (P-Asp140) and 4.6 · 10^?4 S cm^?1 (P-Asp250), respectively. Differential thermogravimetric analysis (TG-DTA) was carried out for each P-Asp. The results were classified into two categories. One exhibited two endothermic peaks between t = (270 and 300) °C, the other exhibited only one peak. The P-Asp group with two endothermic peaks exhibited high proton conductivity. The high proton conductivity is related to the stability of the polymer. The number-average molecular weight also contributed to the stability of the polymer.     

Cycling performance and efficiency of sulfonated poly(sulfone) membranes in vanadium redox flow batteries

As an alternative to Nafion® ion exchange membrane, an inexpensive commercially-available Radel® polymer was sulfonated, fabricated into a thin membrane, and evaluated for its performance in a vanadium redox flow battery (VRFB). The sulfonated Radel (S-Radel) membrane showed almost an order of magnitude lower permeability of VO²⁺ ions (2.07 × 10^?7 cm²/min), compared to Nafion 117 (1.29 × 10^?6 cm²/min), resulting in better coulombic efficiency (~ 98% vs. 95% at 50 mA/cm²) and lower capacity loss per cycle. Even though the S-Radel membrane had a slightly higher membrane resistance, the energy efficiency of the VRFB with the S-Radel membrane was comparable to that of Nafion because of its better coulombic efficiency resulting from the lower vanadium ion crossover. The S-Radel membrane exhibited good performance up to 40 cycles, but a decline in performance at later cycles was observed, likely as a result of membrane degradation.     

Facilitated transport of CO2 through polyethylenimine/poly(vinyl alcohol) blend membrane

Polyethylenimine (PEI)/poly(vinyl alcohol) (PVA) blend membranes were prepared for the facilitated transport of CO₂. The polymeric carrier PEI was retained in the blend membrane by the entanglement with PVA chains. The CO₂ permeance decreased with an increase in CO₂ partial pressure in feed gas, whereas the N₂ permeance was nearly constant. This result clearly showed that only CO₂ was transported by the facilitated transport mechanism. The CO₂ and N₂ permeabilities increased monotonically with the PEI weight percent in the blend membrane, whereas the selectivity of CO₂ over N₂ showed a maximum. The selectivity increased remarkably with increasing heat-treatment temperature of the membrane. The highest selectivity obtained reached more than 230 when the CO₂ partial pressure was 0.065 atm. The prepared membrane was stable.     

Effect of electron beam irradiation on the structural properties of poly(vinyl alcohol) formulations with triphenyl tetrazolium chloride dye (TTC)

Films of poly(vinyl alcohol) (PVA) composites with triphenyl tetrazolium chloride (TTC) dye were prepared and exposed to various radiation doses delivered by accelerated electrons. The results showed that at a low dose of 50 kGy, the colour difference (ΔE^*) of PVA/TTC films was increased by ∼10 times of the initial value. However, the change in colour differences did not go systematically with increasing the TTC content, in which the composite with 1.5 wt% displayed higher value than that with 3.5 wt%. The differential scanning calorimetry (DSC) showed that the presence of the TTC dye caused a depression in the melting point (T_m) and heat of fusion (ΔH_f) of the PVA bulk polymer. However, the thermogravimetric analysis (TGA) showed that the presence of the TTC dye improved the thermal stability of PVA. Also, the tensile strength at break of PVA/TTC composites was improved after electron beam irradiation.     

Preparation of aqueous crosslinked dispersions of functionalized poly(d,l-lactic acid) with a thermomechanical method

Aqueous crosslinked microparticle dispersions were prepared from a copolymer of d,l-lactic acid, 1,4-butanediol, and itaconic acid with a thermomechanical method. The copolymer was prepared in one step polycondensation reaction using Sn(Oct)₂ as a catalyst. A polymer with M_n of 2800 g mol^?1 and a molecular weight distribution of 1.41 was obtained (as determined by SEC), that contained double bonds introduced by the itaconic acid monomer units (6 mol-%, as determined by NMR). Crosslinking ability of the prepared copolymer was demonstrated in bulk by adding a thermal initiator and altering amounts of ethylene glycol dimethacrylate (EGDMA) crosslinking agent into molten polymer at 60–150 °C. A crosslinked gel was formed in less than 15 min at 80 °C when 10 wt.% of EGDMA was added and benzoyl peroxide (BPO) was used as the initiator. Aqueous dispersions were prepared of the non-crosslinked copolymer with a thermomechanical method that involved slow addition of aqueous polyvinyl alcohol (PVA) solution into molten copolymer at 60 °C under shear. Dispersions were prepared with 10 wt.% of EGDMA and 2 wt.% of BPO. Crosslinking of the dispersed microparticles was achieved by heating the dispersions at 80 °C for 30 or 60 min. The dispersions were characterized by SEM, DSC, TGA, FT-IR, solid state NMR, and gel content measurements. The effect of crosslinking was clearly seen in SEM images of films cast from the dispersions. The films cast from non-crosslinked dispersions had smooth morphology whereas in films cast from crosslinked dispersions separate spherical particles were observed. During the crosslinking reactions, glass transition temperatures increased (as determined by DSC), thermal stability of the samples increased (as determined by TGA), and the gel content of the samples increased.     

Synthesis and characterization of photocrosslinkable poly(l-lactide)s with a pendent cinnamate group

In this report, we describe the synthesis and characterization of photosensitive poly(l-lactide) with a pendent cinnamate group. α,ω-Dihydoxy terminated poly(l-lactide) (PLLA-diol) [molecular weights (MW); 2000, 4000 and 9000 g/mol ] was chain-extended with a diacyl chloride of 5-cinnamoyloxyisophthalic acid (ICA) to obtain high-molecular-weight photocrosslinkable poly(l-lactide)s (ICA/PLLA). The resulting polyesters were characterized by proton nuclear magnetic resonance spectroscopy, gel permeation chromatography, ultraviolet–visible spectroscopy, differential scanning calorimetry, thermomechanical analysis and thermogravimetry. The glass transition temperature (T_g), the melting temperature (T_m) and the degree of relative crystallinity (X_c) of ICA/PLLAs increased with the increasing MW of the PLLA-diols. The photosensitive ICA/PLLAs were irradiated with a 400 W high-pressure mercury lamp (λ > 280 nm) for various times to produce the PLLA gel films without a photoinitiator. The crosslinking rate monitored by a UV–vis spectrum decreased with the increasing MW of the PLLA-diols. The crosslinking of the ICA/PLLA ?4000 film enhanced the T_g slightly and the tensile strength and Young’s modulus significantly, while reduced the T_m and X_c. The enzymatic degradation was measured by the weight loss of the films in a phosphate buffer solution with proteinaze-k. The crosslinking of the films decreased markedly the degradation rate.     

Uranyl ion uptake capacity of poly (N-isopropylacrylamide/maleic acid) copolymeric hydrogels prepared by gamma rays

The effect of gel composition, absorbed dose and pH of the solution on the uranyl ion uptake capacity of N-isopropylacrylamide/maleic acid copolymeric hydrogels containing 0–3 mol% of maleic acid at 48 kGy have been investigated. Uranyl uptake capacity of hydrogels are found to increase from 18.5 to 94.8 mg [UO₂²⁺]/g dry gel as the mole % of maleic acid content in the gel structure increased from 0 to 3. The percent swelling, equilibrium swelling and diffusion coefficient values have been evaluated for poly(N-isopropylacrylamide/maleic acid) hydrogels at 500 ppm of uranyl nitrate solution.     

Poly(ether amine) and cross-linked poly(propylene oxide) diacrylate thin-film polymer electrolyte for 3D-microbatteries

This paper presents a novel thin-film electrolyte of a 2:1 blend of polyetheramine (glyceryl poly(oxypropylene)) and cross-linked oligomeric poly(propylene oxide) diacrylate with LiTFSI. The polyetheramine acts as a surfactant, and can thereby be applied as a conformal coating on complex surfaces—here demonstrated for porous LiFePO₄ cathodes—making it useful for 3D-microbatteries. The poly(propylene oxide) diacrylate blends with the surfactant and is easily UV cross-linked, thereby ensuring good mechanical stability. Electrolytes, ~ 2 μm thick, were casted onto LiFePO₄ cathodes and cycled against metallic lithium, displaying stable discharge capacities of ~ 8 mAh/g at room temperature and ~ 120 mAh/g at 60 °C. The electrolyte showed conductivities of 3.45 × 10^? 6 and 5.80 × 10^? 5 S cm^? 1 at room temperature and 60 °C, respectively.     

Thermostable ultrafiltration and nanofiltration membranes from sulfonated poly(phthalazinone ether sulfone ketone)

Modification of poly(phthalazinone ether sulfone ketone) (PPESK) by sulfonation with concentrated or fuming sulfuric acid was carried out in order to prepare thermally stable polymers as membrane materials having increased hydrophilicity and potentially improved fouling-resistance. The sulfonated poly(phthalazinone ether sulfone ketone)s (SPPESK) were fabricated into ultrafiltration (UF) and nanofiltration (NF) asymmetric membranes. The effects of SPPESK concentration and the type and concentration of additives in the casting solution on membrane permeation flux and rejection were evaluated by using an orthogonal array experimental design in the separation of polyethyleneglycol (PEG12000 and PEG2000) and Clayton Yellow (CY, MW 695). One UF membrane formulation type had a 98% rejection rate for PEG12000 and a high pure water flux of 867 kg m⁻² h⁻¹. All the NF membranes made in the present study had rejections of ≥96%, and one had a high water flux of 160 kg m⁻² h⁻¹. Several of the NF membrane formulation types had ∼90% rejection for CY. When the membranes were operated at higher temperatures (80°C), the rejection rates declined slightly and pure water flux was increased more than two-fold. Rejection and flux values returned to previous values when the membranes were operated at room temperature again. Mono- and divalent salt rejections and fluxes were studied on an additional NF membrane set.     

Preparation and characterization of porous conducting poly(dl-lactide) composite membranes

Solid conducting biodegradable composite membranes have shown to enhance nerve regeneration. However, few efforts have been directed toward porous conducting biodegradable composite membranes for the same purpose. In this study, we have fabricated some porous conducting poly(dl-lactide) composite membranes which can be used for the biodegradable nerve conduits. The porous poly(dl-lactide) membranes were first prepared through a phase separation method, and then they were incorporated with polypyrrole to produce porous conducting composite membranes by polymerizing pyrrole monomer in gas phase using FeCl₃ as oxidant. The preparation conditions were optimized to obtain membranes with controlled pore size and porosity. The direct current conductivity of composite membrane was investigated using standard four-point technique. The effects of polymerization time and the concentration of oxidant on the conductivity of the composite membrane were examined. Under optimized polymerization conditions, some composite membranes showed a conductivity close to 10⁻³ S cm⁻¹ with a lower polypyrrole loading between 2 and 3 wt.%. A consecutive degradation in Ringer's solution at 37 °C indicated that the conductivity of composite membrane did not exhibit significant changes until 9 weeks although a noticeable weight loss of the composite membrane could be seen since the end of the second week.     

Epidermal cellular response to poly(vinyl alcohol) nanofibers containing silver nanoparticles

A heat-treated PVA nanofibrous matrix containing silver (Ag) was prepared by electrospinning an aqueous 10 wt% PVA solution and followed by heat treatment at 150 °C for 10 min. The average diameter of the as-spun and heat-treated PVA nanofibers was 330 nm. The heat-treated PVA nanofibrous matrix containing Ag was irradiated with UV light to transform the Ag ions in the nanofibrous matrix into Ag nanoparticles. The in vitro cytotoxicity of the Ag ions and/or nanoparticles on normal human epidermal keratinocytes (NHEK) and fibroblasts (NHEF) cultures was examined. The PVA nanofibrous matrix containing Ag showed slightly higher level of attachment and spreading in the early stage culture (1 h) than the PVA nanofibers without Ag (control). However, compared with the PVA nanofibers without Ag, the heat-treated and UV-irradiated PVA nanofibers, containing mainly Ag ions and nanoparticles, respectively, showed reduced cell attachment and spreading. This shows that both Ag ions and Ag nanoparticles are cytotoxic to NHEK and NHEF. There was no significant difference in cytotoxicity to NHEK and NHEF between Ag ions and Ag nanoparticles. NHEF appeared to be more sensitive to Ag ions or particles than NHEK. In addition, the residual nitrate ions (NO₃⁻) in the PVA nanofibers had an adverse effect on the culture of both cells.     

Poly(vinyl alcohol) separators improve the coulombic efficiency of activated carbon cathodes in microbial fuel cells

High-performance microbial fuel cell (MFC) air cathodes were constructed using a combination of inexpensive materials for the oxygen reduction cathode catalyst and the electrode separator. A poly(vinyl alcohol) (PVA)-based electrode separator enabled high coulombic efficiencies (CEs) in MFCs with activated carbon (AC) cathodes without significantly decreasing power output. MFCs with AC cathodes and PVA separators had CEs (43%–89%) about twice those of AC cathodes lacking a separator (17%–55%) or cathodes made with platinum supported on carbon catalyst (Pt/C) and carbon cloth (CE of 20%–50%). Similar maximum power densities were observed for AC-cathode MFCs with (840 ± 42 mW/m²) or without (860 ± 10 mW/m²) the PVA separator after 18 cycles (36 days). Compared to MFCs with Pt-based cathodes, the cost of the AC-based cathodes with PVA separators was substantially reduced. These results demonstrated that AC-based cathodes with PVA separators are an inexpensive alternative to expensive Pt-based cathodes for construction of larger-scale MFC reactors.     

Proton-conducting membranes based on poly(2,5-benzimidazole) (ABPBI) and phosphoric acid prepared by direct acid casting

We report the preparation of phosphoric acid doped poly(2,5-benzimidazole) (ABPBI) membranes for PEMFC by simultaneously doping and casting from a poly(2,5-benzimidazole)/phosphoric acid/methanesulfonic acid (MSA) solution. The evaporation of MSA yields a very homogeneous membrane having a better controlled composition, avoiding the use of solvent-intensive procedures. Membranes have been prepared with contents of up to 3.0H₃PO₄ molecules per ABPBI repeating unit. These membranes achieve a maximum conductivity of 1.5 × 10⁻² S cm⁻¹ at temperatures as high as 180 °C in dry conditions. These ABPBI membranes are more conveniently prepared than those conventionally formed and doped in separate steps while featuring comparable conductivities (ABPBI × 2.7H₃PO₄ prepared by the soaking method showed a conductivity of 2.5 × 10⁻² S cm⁻¹ at 180 °C in dry conditions).     

Preparation of sulfonated poly(phthalazinone ether sulfone ketone) composite nanofiltration membrane

Thin film composite (TFC) membranes were prepared from sulfonated poly(phthalazinone ether sulfone ketone) (SPPESK) as a top layer coated onto poly(phthalazinone ether sulfone ketone) (PPESK) ultrafiltration (UF) support membranes. The effects of different preparation conditions such as the SPPESK concentration, organic additives, solvent, degree of substitution (DS) of SPPEK and curing treatment temperature and time on the membrane performance were studied. The SPPESK concentration in the coating solution was the dominant factor for the rejection and permeation flux. The TFC membranes prepared from glycerol as an organic additive show better performance then those prepared from other additives. The rejection increased and the flux decreased with increasing curing treatment temperatures. The salt rejections of the TFC nanofiltration (NF) membranes increased in the order MgCl₂ < MgSO₄ < NaCl < Na₂SO₄. TFC membranes showed high water flux at low pressure. SPPESK composite membranes rejections for a 1000 mg L⁻¹ Na₂SO₄ feed solution was 82%, and solution flux was 68 L m⁻² h⁻¹ at 0.25 MPa pressure.     

Effects of PVA,agar contents,and irradiation doses on properties of PVA/ws-chitosan/glycerol hydrogels made by γ-irradiation followed by freeze-thawing

Poly(vinyl alcohol) (PVA)/water soluble chitosan (ws-chitosan)/glycerol hydrogels were prepared by γ-irradiation and γ-irradiation followed by freeze-thawing, respectively. The effects of irradiation dose and the contents of PVA and agar on the swelling, rheological, and thermal properties of these hydrogels were investigated. The swelling capacity decreases while the mechanical strength increases with increasing PVA or agar content. Increasing the irradiation dose leads to an increase in chemical crosslinking density but a decrease in physical crosslinking density. Hydrogels made by irradiation followed by freeze-thawing own smaller swelling capacity but larger mechanical strength than those made by pure irradiation. The storage modulus of the former hydrogels decreases above 50 °C and above 70 °C it comes to the same value as that prepared by irradiation. The ordered association of PVA is influenced by both chemical and physical crosslinkings and by the presence of ws-chitosan and glycerol. These hydrogels are high sensitive to pH and ionic strength, indicating that they may be useful in stimuli-responsive drug release system.     

Rheo-optical FT-IR spectroscopy of poly(3-hydroxybutyrate)/poly(lactic acid) blend films

The orientation of poly(3-hydroxybutyrate) (PHB) and poly(lactic acid) (PLA) segments in PHB/PLA blend films cast from chloroform solutions with compositions PHB < PLA was studied during uniaxial elongation up to 250% strain at 50 °C by in-situ rheo-optical FT-IR spectroscopy. From the orientation functions of the ν(CO) bands of the blend components, it was derived that the PLA chains orient in the direction of elongation while the PHB chains orient perpendicular to the drawing direction. PHB homopolymer and PHB/PLA blend films with PHB > PLA compositions could only be oriented by cold drawing in ice water after quenching from the melt. The IR-dichroic effects of films drawn under these conditions indicate for both blend components a chain alignment parallel to the drawing direction.