Effect of magnetic pulse treatment on the magnetic characteristics of yttrium–iron garnets

The effect weak (10–100 kA m^–1) low-frequency (10–20 Hz) pulsed magnetic fields have on the surface structure and magnetic characteristics of yttrium–iron garnet Y₃Fe₅O₁₂ is studied by means of electron and Mössbauer spectroscopy. A mechanism is proposed for the variation of saturation magnetization in Y₃Fe₅O₁₂ after magnetic pulse treatment. The mechanism is associated with the change in the spin state of iron ions localized in the tetrahedral sublattice.     

Influence of acid catalysts on the structural and magnetic properties of nanocrystalline barium ferrite prepared by sol–gel method

BaFe₁₂O₁₉ powders with nanocrystalline size were prepared by sol–gel techniques. Nitric, hydrochloric, acetic and stearic acid were used to improve the magnetic properties. Amorphous gels were formed with Fe/Ba molar ratio of 10.5. Then powders were obtained by subsequent heat treatment at 800–1000 °C for 1 h. Barium ferrite powder was also synthesized by solid state reaction at 1210 °C. X-ray diffraction, scanning electron microscopy and transmission electron microscopy (TEM) experiments were conducted to evaluate structural properties of the samples. The value of the effective magnetic susceptibility was measured. The results show that the magnetoplumbite structure was formed in all of the powders. The TEM observation showed that the minimum particle size (20 nm) was produced with the stearic acid catalyst. The highest value of the effective magnetic susceptibility was achieved also using stearic acid.     

Enhanced structural and magnetic properties of microwave sintered Li–Ni–Co ferrites prepared by sol–gel method

The properties of lithium ferrites are very sensitive to chemical composition, synthesis method, and sintering techniques. Li–Ni–Co ferrites with compositional formula Li_(0.45-0.5x)Ni_(0.1)Co_xFe_(2.45-0.5x)O_4, where 0.00 ≤ x ≤ 0.1 in steps of 0.02 were prepared by chemical sol–gel method and sintered by microwave sintering technique. The x-ray diffraction patterns confirmed the formation of single phase with spinel structure in all the samples. The structural parameter viz.lattice constant, crystallite size, and x-ray density for these samples were studied and compared with those measured from samples of similar composition prepared by the sol–gel method and sintered by conventional sintering technique. Enhancement in the magnetic properties like Curie temperature, hysteresis parameters was observed by employing sol–gel synthesis combined with microwave sintering. The results obtained and mechanisms involved are discussed in the paper.     

Indium doping effect on properties of ZnO nanoparticles synthesized by sol–gel method

Pure ZnO and indium-doped ZnO(In–ZO) nanoparticles with concentrations of In ranging from 0 to 5% are synthesized by a sol–gel processing technique. The structural and optical properties of ZnO and In–ZO nanoparticles are characterized by different techniques. The structural study confirms the presence of hexagonal wurtzite phase and indicates the incorporation of In~(3+) ions at the Zn~(2+) sites. However, the optical study shows a high absorption in the UV range and an important reflectance in the visible range. The optical band gap of In–ZnO sample varies between 3.16 e V and 3.22 e V. The photoluminescence(PL) analysis reveals that two emission peaks appear: one is located at 381 nm corresponding to the near-band-edge(NBE) and the other is observed in the green region. The aim of this work is to study the effect of indium doping on the structural, morphological, and optical properties of ZnO nanoparticles.     

Optical and transport properties of Sn-doped ZnMn2O4 prepared by sol–gel method

The paper describes the effect of ZnMn₂O₄ doping with different Sn ratios. Sn_x–ZnMn₂O₄ is prepared with Sol–Gel route at 700 °C. The structural, optical and electrical properties were studied. The X-ray diffraction patterns indicate the formation of pure tetragonal phase for the ratios lower than 0.03%, while for other compositions, the secondary phases were observed. The attenuated total reflectance (ATR) analysis confirmed the localization of Sn in octahedral sites. The optical properties showed not only the increase of E_g, but also the improvement of the optical characteristics such as extinction coefficient (k), optical conductivity (σ_opt), dissipation factor (tan δ) and the relaxation time (τ). The latter has been improved by 50%. The Hall measurements confirmed the transition of the conductivity mode, i.e, from p to n-type. The formation of Sn_Mn¹⁺ point defects is evidenced; however, the transport properties indicate that the charge carriers are mainly localized.     

Synthesis and magnetic properties of barium–calcium hexaferrite particles prepared by sol–gel and microemulsion techniques

The preparation of W-type hexaferrite particles with the composition BaCa₂Fe₁₆O₂₇ by microemulsion and a stearic acid sol–gel method with and without surfactant has been investigated at various sintering temperatures. The structural and magnetic characteristics have been studied by X-ray diffraction (XRD), a vibrating sample magnetometer (VSM), scanning electron microscopy (SEM), thermogravimetric analysis (TGA), differential scanning calorimetric (DSC) and Fourier transform infrared (FTIR) techniques. The effect of sintering temperature on the properties of BaCa₂Fe₁₆O₂₇ hexaferrites has been studied. The value of saturation magnetization (M_s) depends on types of surfactant used. The sample prepared in the presence of polyoxyethylene (20) sorbitan monooleat (Tween 80) shows low saturation magnetization (M_s=15.10 emu/g), whereas the other sample prepared in the presence of a surfactant cetyltrimethylammonium bromide (CTAB) exhibits high saturation magnetization (M_s=24.60 emu/g) compared to the normal sample.     

Enhanced soft magnetic properties of iron powders through coating MnZn ferrite by one-step sol–gel synthesis

The MnZn ferrite coating formed on the surface of iron-based soft magnetic powders via facile and modified sol–gel process has been fabricated to obtain better magnetic performance due to its higher permeability compared with traditional nonmagnetic insulation coatings. The influence of the MnZn ferrite contents on the magnetic performance of the soft magnetic composites(SMCs) has been studied. As the MnZn insulation content increases, the core loss first experiences a decreasing trend that is followed by progressive increase, while the permeability follows an increasing trend and subsequently degrades. The optimized magnetic performance is achieved with 2.0 wt% MnZn ferrite, which results from the decrement of inter-particle eddy current losses based on loss separation. A uniform and compact coating layer composed of MnZn ferrite and oxides with an average thickness of 0.38 ± 0.08 μm is obtained by utilizing ion beam technology, and the interface between the powders and the coating shows satisfied adhesiveness compared with the sample directly prepared by mechanical mixing. The evolution of the coating layers during the calcination process has been presented based on careful analysis of the composition and microstructure.     

Effect of calcination atmosphere on photoluminescence properties of nanocrystalline ZrO2 thin films prepared by sol–gel dip coating method

Highly transparent and homogeneous nanocrystalline ZrO₂ thin films were prepared by the sol–gel dip coating method. The X-ray diffraction (XRD) pattern of ZrO₂ thin films calcined in air, O₂ or N₂ shows the formation of tetragonal phase with varying crystallite size. X-ray photoelectron spectroscopy (XPS) gives Zr 3d and O 1s spectra of thin film annealed in air, which reveal zirconium suboxide component (ZrO_x, 0<x<2), Zr–O bond and surface defects. An average transmittance greater than 85% (in UV–vis region) is observed in all calcined samples. Photoluminescence (PL) reveals an intense emission peak at 379 nm and weak peaks at 294, 586 and 754 nm for ZrO₂ film calcined in air. An enhancement of PL intensity and red-shift is observed in films calcined in O₂ and N₂ atmosphere. This is due to the reconstruction of zirconium nanocrystal interfaces and vacancies, which help passivate the non-radiative defects. The oxygen deficient defect, which is due to the distorted Zr–O bond, is suggested to be responsible for photoluminescence. The defect states in the nanocrystalline zirconia thin films play an important role in the energy transfer process. The luminescence defects in the film make it suitable for gas sensors development and tunable lasers.     

Microwave behavior of ferrites prepared via sol–gel method

Ni-ferrites were prepared at different temperatures via sol–gel method. The electromagnetic properties of these materials, namely permittivity and permeability were measured in the 0.1–13 GHz frequency range. Following a mathematical procedure, microwave absorption diagrams were constructed including the dependence of the microwave absorption of ferrite layer on microwave frequency and layer thickness. The permeability spectra broaden and the microwave absorption improves at 9–10 GHz with increase of annealing temperature.     

Structures and local ferroelectric polarization switching properties of orthorhombic YFeO_3 thin film prepared by a sol–gel method

Orthorhombic YFeO_3 thin film was prepared on La_(0.67)Sr_(0.33)MnO_3/LaAlO_3 substrate by a sol-gel spin-coating method. The structures of the YFeO_3/La_(0.67)Sr_(0.33)MnO_3/LaAlO_3(YFO/LSMO/LAO) sample were detected by x-ray diffraction pattern, Raman spectrometer, scanning electron microscopy, and atomic force microscope. The local ferroelectric polarization switching properties of the orthorhombic YFO film were confirmed by piezoresponse force microscopy(PFM) for the first time. The results show that the YFO film deposited on LSMO/LAO possesses orthorhombic structure,with ultra-fine crystal grains and flat surface. The leakage current of the YFO film is 8.39 × 10~(-4) A·cm~(-2) at 2 V,with its leakage mechanism found to be an ohmic behavior. PFM measurements indicate that the YFO film reveals weak ferroelectricity at room temperature and the local switching behavior of ferroelectric domains has been identified. By local poling experiment, polarization reversal in the orthorhombic YFO film at room temperature was further observed.     

Influence of post-deposition annealing on the structural and optical properties of ZnO thin films prepared by sol–gel and spin-coating method

Thin films of zinc oxide have been deposited onto (0001) sapphire substrate by sol–gel and spin-coating methods. The XRD pattern showed that the crystallinity of the annealed ZnO films had improved in comparison with that of the as-grown films. Photoluminescence spectra revealed a two-line structure, which is identified in terms of UV emission and defect-related emission. The emission intensity was found to be greatly dependent on heat treatment. Host phonons of ZnO and a shift of the _E2$E_2$ (high) peak from its position have been observed from Raman spectra. The surface morphologies of the film had been improved after annealing was observed from AFM images.     

Photoconductivity studies on nanoporous TiO2/dopamine films prepared by sol–gel method

Dopamine was encapsulated into nanoporous amorphous TiO₂ matrix by sol–gel method under atmospheric conditions. A second sample was obtained by the addition of the crown-ether 15C5 in this previous sample. Thin films were spin-coated on glass wafers. No heat treatment was employed in both films. All films were characterized using infrared spectroscopy, high resolution transmission electronic microscopy, X-ray diffraction, optical absorption and scanning electronic microscopy. Despite the films prepared with 15C5 were no calcined, a partial crystallization was identified. Anatase and rutile nanoparticles with sizes of 4–5 nm were obtained. Photoconductivity technique was used to determine the charge transport mechanism on these films. Experimental data were fitted with straight lines at darkness and under illumination wavelengths at 320, 400, and 515 nm. It indicates an ohmic behavior. Photovoltaic and photoconductivity parameters were determined from the current density vs. the applied-electrical-field results. Amorphous film has bigger photovoltaic and photoconductive parameters than the partially crystalline film. Results observed in the present investigation prove that the nanoporous TiO₂ matrix can protect the dopamine inhibiting its chemical instability. This fact modifies the optical, physical and electrical properties of the film, and is intensified when 15C5 is added.     

Effects of calcining temperature on structural and magnetic properties of nanosized Fe-doped NiO prepared by diol-based sol−gel process

Iron-doped nickel oxide (Fe_0.01Ni_0.99O, abbreviated as FNO) nanoparticles were prepared by sol–gel process using 1,3-propanediol as a solvent and also as a chelating agent, and calcined at the various temperatures (400–1000 °C) for 2 h. The phase composition and the microstructure of the calcined products were investigated by X-ray diffraction and scanning electron microscopy techniques, respectively. Magnetic properties were measured at room temperature using a vibrating sample magnetometer. All calcined samples showed the single phase of FNO cubic rock-salt structure without the presence of any impurity phases. The crystallite size from XRD and particle size from SEM increased as calcining temperature increased. The FNO powders calcined at 400?600 °C revealed the uniform and dense spherical particles in nanosize. The room-temperature ferromagnetism was observed for all samples. When the calcining temperature was increased, the saturation magnetization decreased whereas the coercivity increased, corresponding to the less dense and larger particles. The calcined sample at 400 °C had the best magnetic properties with the highest M_s of 5.34 emu/g (at 10 kOe) and the lowest H_c of 372 Oe.     

Effects of Cd concentration on structure and optical properties of the ternary Zn1−xCdxO nanopowder prepared by sol–gel method

Zn_1−xCd_xO nanocrystalline powder with different Cd contents (0≤x≤1) has been prepared by new facile sol–gel route. The crystal structure and optical properties were investigated by X-ray diffraction patterns, Transmission electron microscope, X-ray photoelectron spectroscopy, Photoluminescence. As x varied from x=0 to 0.25, the Zn_1−xCd_xO nanopowder exhibits a hexagonal wurtzite structure of pure ZnO without any significant formation of a separated CdO phase. For the samples with 0.5≤x≤0.85, the Zn_1−xCd_xO nanopowder exhibits the coexistence of hexagonal ZnO and cubic CdO phase, meanwhile, the content of ZnO phase decreases while that of CdO increases with increasing the Cd content x. The ultra-violet near-band-edge emission of the Zn_1−xCd_xO nanopowder was monotonously red-shifted from 389 nm (x=0) to 406 nm (x=0.25) due to the direct modulation of band gap caused by Cd substitution.     

Study of NiCuZn ferrite powders and films prepared by sol gel method

This paper reports that a series of NiCuZn ferrite powders and films are prepared by using sol-gel method.The effects of raw material composition and the calcinate temperature on magnetic properties of them are investigated.The NiCuZn ferrite powders are prepared by the self-propagating high-temperature synthesis method and subsequently heated at 700 C～1000 C.The results show that NiCuZn ferrite powders with single spinel phase can be formed after heat-treating at 750 C.Powders obtained from Ni 0.4 Cu 0.2 Zn 0.4 Fe 1.9 O 4 gel have better magnetic properties than those from gels with other composition.After heat-treating at 900 C for 3 h,coercivity H c and saturation magnetization M s are 9.7 Oe (1 Oe=80 A/m) and 72.4 emu/g,respectively.Different from the powders,NiCuZn films produced on Si (100) from the Ni 0.4 Cu 0.2 Zn 0.4 Fe 2 O 4 gel formed at room temperature possess high properties.When heat-treating condition is around 600 C for 6 min,samples with low H c and high M s will be obtained.The minimal H c is 16.7 Oe and M s is about 300 emu/cm 3.In comparison with the films prepared through long-time heat treating,the films prepared through short heat-treating time exhibits better soft magnetic properties.     

Nanostructures and luminescence properties of porous ZnO thin films prepared by sol–gel process

ZnO thin films containing nano-sized pores were synthesized on solid substrates through a sol–gel process by accommodating cetyl-trimethyl-ammonium bromide (CTAB) as an organic template in the precursor solution. By X-ray diffraction the resultant ZnO films were found to possess ordered pore arrays forming lamellar structure with the spacing between two adjacent pores being ∼3.0 nm. Photoluminescence measurements indicated that the surfactants effectively passivated the surface defects of the ZnO films responsible for the green emission. Al doping was found to improve not only the lamellar structure of the pore arrays but also the near-band-gap emission intensity while the suppression effect of CTAB on the green emission remained undisturbed. With a proper control of doping level, the optical property as well as the structural integrity can be tailored to augment the potential of ZnO films for the optoelectronics and sensor applications.     

Photoluminescent properties of Dy3+ in MgO-Ga2O3-SiO2 nano-glass-ceramic prepared by sol–gel method

The MgO-Ga₂O₃-SiO₂ (MGS) glass and glass-ceramic (GC) containing MgGa₂O₄ nanocrystals and Dy³⁺ ions were prepared by a simple sol–gel method. MgGa₂O₄ nanocrystals in MgO-Ga₂O₃-SiO₂ GC formed when the heating temperature reached 800 °C. The energy transfer from MgGa₂O₄ nanocrystals to Dy³⁺ was observed. It is important that the strong white light emission is observed corresponding to the excitation band gap of MgGa₂O₄ nanocrystals. As exciting Dy³⁺ ions, only weak yellow and blue emissions were observed.     

Characterization,electrical conduction and stability of Yb-doped barium cerate prepared by sol–gel method

Ceramics powder of BaCe_0.95Yb_0.05O_2.975 was successfully prepared by sol–gel method. Thermogravimetric analysis showed that the decomposition of the dried powder was completed at 1,000 °C. Three strongly exothermic peaks observed in differential thermogravimetric signal indicated three major stages of weight loss in the sample. The high crystallinity of sample with orthorhombic structure was confirmed by X-ray diffraction. The loose particles size obtained from scanning electron microscope was in the range of 65–100 nm, which is almost in the same range as that observed in particle size distribution. The sample showed a dc conductivity of ~1.3 × 10⁻⁴ S cm⁻¹ at 650 °C and the activation energy, E _a, was found to be 1.4 eV. Result of chemical stability test showed that the compound was unstable in atmosphere containing pure carbon dioxide.     

Electrical and optical properties of Sb-doped ZnO thin films synthesized by sol–gel method

Sb-doped ZnO thin films with different values of Sb content （from 0 to 1.1 at.%） are deposited by the sol-gel dip- coating method under different sol concentrations. The effects of Sb-doping content, sol concentration, and annealing ambient on the structural, optical, and electrical properties of ZnO films are investigated. The results of the X-ray diffraction and ultraviolet-visible spectroscopy （UV-VIS） spectrophotometer indicate that each of all the films retains the wurtzite ZnO structure and possesses a preferred orientation along the c axis, with high transmittance （〉 90%） in the visible range. The Hall effect measurements show that the vacuum annealed thin films synthesized in the sol concentration of 0.75 mol/L each have an adjustable n-type electrical conductivity by varying Sb-doping density, and the photoluminescence （PL） spectra revealed that the defect emission （around 450 nm） is predominant. However, the thin films prepared by the sol with a concentration of 0.25 mol/L, despite their poor conductivity, have priority in ultraviolet emission, and the PL peak position shows first a blue-shift and then a red-shift with the increase of the Sb doping content.