Enhancement of magnetic properties of Co/Pd multilayered perpendicular magnetic recording media by using Pd/Si dual seedlayer

Effects of the introduction of a Pd/Si dual seedlayer on the microcrystalline structure and magnetic properties of [Co/Pd]_n multilayered perpendicular magnetic recording media were investigated. The Pd/Si dual seedlayer was composed of a Pd upper seedlayer and a Si under seedlayer. The Pd upper seedlayer with a thickness of up to 10 nm markedly increased the coercivity of [Co/Pd]_n multilayered media in the direction perpendicular to the film surface. The highest coercivity of 7.8 kOe was obtained for the [Co/Pd]₁₀ medium with a Pd (10 nm)/Si (100 nm) dual seedlayer. The Pd upper seedlayer not only facilitated the formation of regular interfaces between the Co and Pd layers, but also reduced the thickness of the deteriorated initial layer in the [Co/Pd]_n multilayer, resulting in enhancement of the magnetic anisotropy field. The [Co/Pd]_n multilayered medium with the Pd/Si dual seedlayer exhibited weak intergranular exchange coupling between [Co/Pd]_n grains, which led to excellent read–write characteristics.     

Surface modification of Ni and Co metal nanowires through MeV high energy ion irradiation

Nickel (Ni) and cobalt (Co) metal nanowires were fabricated by using an electrochemical deposition method based on an anodic alumina oxide (Al₂O₃) nanoporous template. The electrolyte consisted of NiSO₄ · 6H₂O and H₃BO₃ in distilled water for the fabrication of Ni nanowires, and of CoSO₄ · 7H₂O with H₃BO₃ in distilled water for the fabrication of the Co ones. From SEM and TEM images, the diameter and length of both the Ni and Co nanowires were measured to be ∼ 200 nm and 5–10 μm, respectively. We observed the oxidation layers in nanometer scale on the surface of the Ni and Co nanowires through HR–TEM images. The 3 MeV Cl²⁺ ions were irradiated onto the Ni and Co nanowires with a dose of 1 × 10¹⁵ ions/cm². The surface morphologies of the pristine and the 3 MeV Cl²⁺ ion-irradiated Ni and Co nanowires were compared by means of SEM, AFM, and HR–TEM experiments. The atomic concentrations of the pristine and the 3 MeV Cl²⁺ ion-irradiated Ni and Co nanowires were investigated through XPS experiments. From the results of the HR–TEM and XPS experiments, we observed that the oxidation layers on the surface of the Ni and Co nanowires were reduced through 3 MeV Cl²⁺ ion irradiation.     

Large spontaneous Hall angle in [Co,CoFe/Pt] multilayer

We have quantitatively investigated the Hall effect in [Co, CoFe/Pt] multilayer films. The [Co, CoFe/Pt] multilayers exhibit large spontaneous Hall resistivity (ρ_H) and Hall angle (ρ_H/ρ). Even though the Hall resistivity in [Co, CoFe/Pt] multilayer films (2.7–4 × 10⁻⁷ Ω cm) is smaller than that of amorphous RE–TM alloy films which show large spontaneous Hall resistivity (<2 × 10⁻⁶ Ω cm), the Hall angle of multilayer (6–8%) is almost twice than that in amorphous rare earth–transition metal alloy films (∼3%). The Hall angle provides evidence of the effects of the exchange interaction of the Hall scattering. The exchange is between conduction electron spins and the localized spins of the transition metal. The large Hall angle of [Co, CoFe/Pt] multilayer can be considered due to the high spin polarization and high Curie temperature of Co and CoFe transition metal layers. Even though the role of interfaces and surfaces in the magnetic properties of multilayer films may dominate that of the bulk, the Hall effects in [Co, CoFe/Pt] multilayer may be mainly dominated by the bulk effect.     

Improved short-circuit photocurrent densities in dye-sensitized solar cells based on ordered arrays of titania nanotubule electrodes

We report on the synthesis of highly ordered arrays of titania nanotubules and their applications in enhanced photoelectrochemical cells. Ordered arrays of titania nanotubules of ∼120 nm external diameter, ∼100 nm internal diameter, and ∼5 μm length were fabricated on transparent conductive oxide (TCO) glass substrates by sol–gel processes using in-house prepared anodic alumina templates. After thermal bonding and template removal, the resultant nanotubule structures were applied in dye-sensitized solar cells (DSCs). Overall photoconversion efficiency of nearly 4.8% was achieved with Ru-bipyridine dye, N719, and iodolyte liquid electrolyte. This remarkable performance, for electrodes only ∼5 μm thick, is attributed to an unexpectedly high short-circuit photocurrent density of 16 mA/cm² for masked cells and up to 17 mA/cm² for unmasked cells. The enhanced short-circuit photocurrent (J_sc) is attributed to the high surface area (roughness factor ca. 1207) of the nanotubules and thus improved dye adsorption to the electrodes. The improved J_sc is also attributed to the parallel and vertical orientation of the nanostructures and thus to a well-defined electron diffusion path.     

Magnetic and structural properties of the electrochemically deposited arrays of Co and CoFe nanowires

Magnetic and structural properties of the arrays of 18 nm diameter nanowires of Co and Co₉₀Fe₁₀ electrodeposited in the pores of anodic alumina are investigated. Arrays of Co and Co₉₀Fe₁₀ nanowires show perpendicular magnetic anisotropy and textured crystallographic behaviour. Coercivity H_c (⊥) and remanence M_r/M_s (⊥) values of 2275 Oe (Co₉₀Fe₁₀); 1188 Oe (Co) and 96% (Co₉₀Fe₁₀), 81% (Co) are observed. The continuous films of Co and Co₉₀Fe₁₀ on Cu substrates show in plane magnetic anisotropy and coercivity values between 109 and 288 Oe.     

Structural and magnetic properties of BCC Fe/Co (0 0 1) superlattices

In thin layered Fe/Co (0 0 1), grown on MgO (0 0 1), both Fe and Co crystallize in the body-centered cubic (BCC) structure, as seen in a series of superlattices where the layer thickness of the components is varied from two to twelve atomic monolayers. These superlattices have novel magnetic properties as observed by magnetization and polarized neutron reflectivity measurements. There is a significant enhancement of the magnetic moments of both Fe and Co at the interfaces. Furthermore, the easy axis of the system changes from [1 0 0] for films of low cobalt content to [1 1 0] for a Co content exceeding 33%. No indication of a uniaxial anisotropy component is found in any of the samples. The first anisotropy constant (K₁) of BCC Co is found to be negative with an estimated magnitude of 110 kJ/m³ at 10 K. In all cases, the magnetic moments of Fe and Co have parallel alignment.     

A new carbon nitride synthesized by shock compression of organic precursors

A series of shock recovery experiments up to ∼50 GPa were carried out on three nitrogen-rich materials of a C–N–O amorphous precursor, dicyandiamide and melamine. The powder X-ray diffractions (XRD) of recovered samples show that carbon nitride phases are formed. They are β-C₃N₄ and a new crystalline phase. The new phase is indexed as a monoclinic cell with a=0.981 nm, b=0.723 nm, c=0.561 nm, β=95.2° and V_cell=0.3966 nm³. Melamine was very stable and did not decompose up to ∼37 GPa. This new phase is considered to form during the adiabatic release process with an extremely high quenching rate (∼10⁹ K/s) and shock compression may provide a novel synthesis route for various C–N phases from appropriate organic materials.     

Cathodoluminescence studies of un-doped and (Cu,Fe, and Co)-doped tin dioxide films deposited by spray pyrolysis

Un-doped and (Cu, Fe, and Co)-doped SnO₂ were studied using films deposited by spray pyrolysis. Room temperature cathodoluminescence (CL) was measured. Differences in CL spectra were observed as a function of deposition parameters (T_sub-350–550 °C), the nature and concentration of dopants (0–16 at.%), and the resulting high annealing temperature (T_an = 700–950 °C). A possible luminescence mechanism has been discussed. It was established that changes taking place in CL spectra were caused by the change of both the grain size and crystallinity (stoichiometry) of the surface layer. It was concluded that radiative recombination occurs through shallow donor levels associated with O-vacancies and trapped centers. It was assumed that in SnO₂ there are apparently three types of defects forming deep levels located at 0.8–0.9, 1.3–1.4, and ∼1.6 eV from the top of the valence band.     

Compositional and structural medium energy ion scattering study of the temperature mediated diffusion determination at the Co/V interface in Co/V/MgO(100)

The impact of annealing at 300 °C on the elemental composition and the atomic structure of the Co/V interface in the 2.5 Å Co/70 Å V/MgO (100) system has been investigated by medium energy ion scattering (MEIS) using 100 keV He⁺ ions. By combining the experimental MEIS results with simulations we show that, while the Co/V interface is abrupt for the system kept at room temperature, annealing at 300 °C induces a strong interdiffusion leading to a Co_0.5V_0.5 surface bcc alloy with a high degree of disorder. Additionally, the MEIS data suggest that the surface of the annealed system is slightly rumpled by ~ 0.2 Å.     

Surface and frustration evidence in Co–Ni–B nanoparticles by FMR measurements

We present ferromagnetic resonance (FMR) measurements on ∼3 nm amorphous magnetic nanoparticles of Co–Ni–B as a function of temperature (T). The particles were studied in powder form and dispersed in a polymer matrix to study the interparticle interaction effect. In both samples the FMR responses are similar down to T∼10 K, where the powder sample shows an intensity increase not followed by the dispersed sample. We argue that the general characteristics are compatible with previous magnetization measurements and Monte Carlo simulations indicating large surface contributions to the effective anisotropy. In this case the frustration of the single-particle behavior observed in the powder sample at very low T (T ⩽ 10 K) is due to interparticle interactions.     

Temperature-induced metamagnetic transition in ErCo3: influence of Fe and Ni substitutions for Co

The phenomenon of a temperature-induced itinerant metamagnetism in ErCo₃ (at 65 K) was investigated with respect to small substitutions of Fe and Ni for Co. Five percent of Fe or Ni substitutions change the transition temperature to 170 or 25 K, respectively. The transition is accompanied by a large magneto-volume effect, ΔV/V reaches ∼0.5%, which allowed to relate the thermal expansion data with the magnetic state of the d-electrons. The change of the magnetic characteristics with substitutions is mainly ascribed to the shift of the position of the Fermi level in the hybridised d-electron energy band.     

Interface characterization of a [Pt/Co)]3/IrMn multilayer by laser-assisted tomographic atom probe

A sputtered Ta_3 nm/[[Pt_2 nm/Co_0.4 nm)]₃/IrMn_7 nm]₇/Pt_10 nm multilayer has been analyzed by laser-assisted tomographic atom probe, allowing to perform three-dimensional reconstructions of the layers and to determine their chemical composition at the atomic scale. From the concentration profiles, we show that the Co layer in contact with IrMn is strongly mixed. The Co/IrMn and IrMn/Pt interfaces are thus non-symmetric, the Co/IrMn interface being more diffuse than the IrMn/Pt one. This study demonstrates that the LATAP technique is extremely well suited for atomic scale structural and chemical characterizations of magnetic multilayers in relationship with their magnetic properties.     

Modeling of electrical and optical characteristics of near room-temperature CdS/ZnSe based NIR photodetectors

Results of modeled photodetector characteristics in (CdS/ZnSe)/BeTe multi-well diode with p–i–n polarity are reported. The dark current density (J–V) characteristics, the temperature dependence of zero-bias resistance area product (R₀A), the dynamic resistance as well as bias dependent dynamic resistance (R_d) and have been analyzed to investigate the mechanisms limiting the electrical performance of the modeled photodetectors. The quantum efficiency, the responsivity and the detectivity have been also studied as function of the operating wavelength. The suitability of the modeled photodetector is demonstrated by its feasibility of achieving good device performance near room temperature operating at 1.55 μm wavelength required for photodetection in optical communication. Quantum efficiency of ∼95%, responsivity ∼0.6 A/W and D^* ∼ 5.7 × 10¹⁰ cm Hz^1/2/W have been achieved at 300 K in X BeTe conduction band minimum.     

Investigation of magnetic properties of interacting Fe2O3 nanoparticles

The magnetic properties of Fe₂O₃ nanoparticles (average diameter ∅≅3 nm) in alumina (68% Fe₂O₃ in weight) have been investigated by magnetization measurements. The results indicate a superparamagnetic behavior of interacting particles, which block with decreasing temperature (the zero-field-cooled susceptibility shows a maximum at T≅145 K) with a distribution of relaxation times. A change of magnetic regime is observed below ∼60 K, due to the increasing interparticle interactions and local surface anisotropy.     

Synthesis of Co nanocapsules coated with BN layers by annealing of KBH4 and [Co(NH3)6]Cl3

Cobalt (Co) nanocapsules coated with boron nitride (BN) layers were synthesized by annealing of ammine complex. KBH₄ and [Co(NH₃)₆]Cl₃ were used as starting materials, and annealed these powders at 500–1000 °C with flowing nitrogen gas. Formation of fcc-Co nanocapsules coated with BN layers was observed from X-ray diffraction patterns and high-resolution electron microscopy. Particle size of fcc-Co prepared at 1000 °C with flowing 100 sccm N₂ gas was approximately 40 nm, and the values of saturation magnetization and coercivity were 74.5 emu/g and 88 Oe, respectively. Good oxidation- and wear-resistances were obtained by encapsulating Co nanoparticles with BN layers.     

Oxygen adsorption properties of YBaCo4O7-type compounds

The oxygen adsorption and desorption of newly found compounds RBaCo₄O₇ (R = Y, Dy–Lu, In) were investigated by thermogravimetry (TG) in the temperature range from room temperature to 1100 °C. The influence of Co replaced by Zn and Fe on the oxygen diffusion properties of YBaCo₄O₇ was also studied. TG results showed clearly that all RBaCo₄O₇ compounds basically experience two oxygen adsorption and desorption processes in the temperature range 20∼1100 °C in oxygen flow. One happens at about 200∼450 °C and the another happens at about 660∼1050 °C. The differences between the resulting states by adsorbing oxygen at lower and high temperature were discussed based on the X-ray diffraction (XRD) patterns and TG data. We showed evidence that the oxygen adsorption at the lower temperature has a small activation energy, while the oxygen adsorption at the higher temperature has a large activation energy. The oxygen adsorbed at high temperature will destroy the RBaCo₄O₇ structure. Zn substituting in the YBaCo_4 − xZn_xO₇ influences the oxygen diffusion behavior prominently, the amount of oxygen adsorbed becomes increasingly weak with the increase of Zn content and disappears completely for the samples with x ≥ 2.0. However, replacement of Co by Fe has little effect on the oxygen absorption process.     

Magnetoresistance of single Co nanowires

Polycrystalline single Co nanowires are prepared by electron beam lithography on GaAs substrates at room temperature. The width of the Co nanowires is varied between 150 and 4000 nm. Magnetoresistance measurements are carried out in a temperature range between 1.5 and 45 K applying magnetic fields μ₀H up to 4.5 T parallel and perpendicular to the current direction. The in plane (longitudinal) magnetoresistance (MR) shows pronounced features at magnetic fields H_c (coercive fields) indicating the magnetization reversal process. From the MR-curves we determined H_c as a function of the angle α between current and field direction (from in plane to out of plane) and of the width w of the Co nanowires. The H_c=H_c(α,w) behavior allows to discuss the reversal process in more detail.     

High coercivity Nd2(Fe,Co)14C-type ribbons prepared by melt spinning

Melt-spun Nd₁₃Dy₂Fe_77−xCo_xC₆B₂ (x=0, 5, 10, 15, 20) ribbons with a high coercivity more than 2 T have been obtained. It was found that the ribbons quenched at the optimum wheel speed 15 m/s (as-spun ribbons) mainly consist of ferromagnetic 2 : 14 : 1 phase and paramagnetic NdC₂ phase, and the ribbons spun at 25 m/s and subsequently annealed at 973 K for 15 min (as-annealed ribbons) are primarily composed of the magnetic 2 : 14 : 1 and 2 : 17 phases. The magnetization process of as-spun ribbons controlled by a pinning of the domain wall is different from that of as-annealed ribbons determined by a nucleation of the reverse domain. This significant difference originates possibly from the existence of paramagnetic NdC₂ phase acting as a pinning center in as-spun ribbons. In the as-annealed ribbons, the substitution of Co for Fe leads to increase of remanence (μ₀M_r), maximum energy product ((BH)_max) from 0.67 T, 9.7 MGOe for x=0 to 0.84 T, 14.4 MGOe for x=10, respectively. A coercivity of 2.74 T is obtained for as-quenched Nd₁₃Dy₂Fe_77−xCo_xC₆B₂ (x=0) ribbons.     

The effect of Ag layer thickness on the properties of WO3/Ag/MoO3 multilayer films as anode in organic light emitting diodes

Transparent conductive WO₃/Ag/MoO₃ (WAM) multilayer electrodes were fabricated by thermal evaporation and the effects of Ag layer thickness on the optoelectronic and structural properties of multilayer electrode as anode in organic light emitting diodes (OLEDs) were investigated using different analytical methods. For Ag layers with thickness varying between 5 and 20 nm, the best WAM performances, high optical transmittance (81.7%, at around 550 nm), and low electrical sheet resistance (9.75 Ω/cm²) were obtained for 15 nm thickness. Also, the WAM structure with 15 nm of Ag layer thickness has a very smooth surface with an RMS roughness of 0.37 nm, which is suitable for use as transparent conductive anode in OLEDs. The current density?voltage?luminance (J?V?L) characteristics measurement shows that the current density of WAM/PEDOT:PSS/TPD/Alq₃/LiF/Al organic diode increases with the increase in thickness of Ag and WO₃/Ag (15 nm)/MoO₃ device exhibits a higher luminance intensity at lower voltage than ITO/PEDOT:PSS/TPD/Alq₃/LiF/Al control device. Furthermore, this device shows the highest power efficiency (0.31 lm/W) and current efficiency (1.2 cd/A) at the current density of 20 mA/cm², which is improved 58% and 41% compared with those of the ITO-based device, respectively. The lifetime of the WO₃/Ag (15 nm)/MoO₃ device was measured to be 50 h at an initial luminance of 50 cd/m², which is five times longer than 10 h for ITO-based device.     

Suppression of structural degradation of LiNi0.9Co0.1O2 cathode at 90 °C by AlPO4-nanoparticle coating

This study examined the electrochemical and structural stability of ∼1.5 wt.% AlPO₄-coated LiNi_0.9Co_0.1O₂. The AlPO₄-coated LiNi_0.9Co_0.1O₂ retained ∼60% of the original capacity after 50 cycles, compared with the ∼30% capacity retention of the bare LiNi_0.9Co_0.1O₂. The discharge profiles and cyclic voltammograms from 4.5 V at 90 °C for 4 h showed enhanced structural stability. Scanning electron microscopy and X-ray diffraction revealed that the AlPO₄-coated LiNi_0.9Co_0.1O₂ had less degradation than the bare LiNi_0.9Co_0.1O₂.