Polyethersulfone/polyacrylonitrile blend ultrafiltration membranes with different molecular weight of polyethylene glycol: preparation,morphology and antifouling properties

Asymmetric ultrafiltration (UF) membranes were prepared from blends of polyethersulfone (PES)/polyacrylonitrile (PAN) via phase inversion method induced by immersion precipitation. Polyethylene glycol (PEG) with four different molecular weights was used as pore former and hydrophilic polymeric additive. N,N‐dimethylformamide (DMF) and water were used as solvent and coagulant (nonsolvent), respectively. The effects of different proportion of PES/PAN and molecular weight of PEG on morphology and performance of the prepared membranes were investigated. Performance of the membranes was evaluated using UF experiments of pure water and buffered bovine serum albumin (BSA) solution as feed. The contact angle measurements indicated that the hydrophilicities of PES/PAN membrane increase by increasing the PAN concentration in the casting solution. However, performance of the membranes improves by increasing the PAN concentration in the casting solution up to 20% and then decreases with further addition of PAN. It was found out that the rejection of BSA decreases with increasing the PAN concentration in the casting solution. Furthermore, it was found that the performance of the membranes increases by increasing the molecular weight of PEG up to 1500 Da and then decreases with the higher molecular weights. The morphology of the prepared membranes was studied by scanning electron microscopy. Copyright © 2011 John Wiley & Sons, Ltd.     

Hydration regulates thermodynamics of G-quadruplex formation under molecular crowding conditions

The effect of molecular crowding on the structure and stability of biomolecules has become a subject of increasing interest because it can clarify how biomolecules behave under cell-mimicking conditions. Here, we quantitatively analyzed the effects of molecular crowding on the thermodynamics of antiparallel G-quadruplex formation via Hoogsteen base pairs and of antiparallel hairpin-looped duplex (HP duplex) formation via Watson-Crick base pairs. The free energy change at 25 degrees C for G-quadruplex formation decreased from -3.5 to -5.5 kcal mol(-1) when the concentration of poly(ethylene glycol) 200 was increased from 0 to 40 wt %, whereas that of duplex formation increased from -9.8 to -6.9 kcal mol(-1). These results showed that the antiparallel G-quadruplex is stabilized under molecular crowding conditions, but that the HP duplex is destabilized. Moreover, plots of stability (ln K(obs)) of the DNA structures versus water activity (ln a(w)) demonstrated that the ln K(obs) for G-quadruplex formation decreased linearly as the ln a(w) increased, whereas that for duplex formation increased linearly with the increase in ln a(w), suggesting that the slope approximately equals the number of water molecules released or taken up during the formation of these structures. Thus, molecular crowding affects the thermodynamics of DNA structure formation by altering the hydration of the DNA. The stabilization of the DNA structures with Hoogsteen base pairs and destabilization of DNA structures with Watson-Crick base pairs under molecular crowding conditions lead to structural polymorphism of DNA sequences regulated by the state of hydration.     

Influence of silicic acid hydrogel dehydration conditions on formation of silica gel structure with molecular sieve properties

In a study of the influence of the temperature and rate of dehydration on the pore structure of silica gel, it has been shown that, in the drying stage, the primary condition for the formation of silica gels with molecular sieve properties is a constant rate of dehydration, ensuring uniform shrinkage of the gel framework.Translated from Teoreticheskaya i Éksperimental'naya Khimiya, Vol. 29, No. 4, pp. 356–360, July–August, 1993.     

Modification of polysulfone hollow fiber ultrafiltration membranes using hyperbranched polyesters with different molecular weights

A series of hyperbranched polyesters (HBPEs) using trimethylolpropane (TMP) as a core were synthesized via an esterification reaction, and the molecular weights of these HBPEs were 1600, 2260, 3370, and 5170 g/mol, respectively. Then, these HBPEs were added into dope solutions to prepare PSf hollow fiber membranes via a wet‐spinning method. When the HBPE molecule weight increased from 1600 to 5170 g/mol, the initial viscosities of the PSf–HBPE–PEG400–DMAc dope solutions increased, and the shear‐thinning phenomenon of these dope solutions became increasingly obvious. When these dope solutions were immersed into the deionized water, the demixing rate increased with an increase in the HBPE molecule weight at first and then decreased; this results in the increase of membrane porosity and the coexistence of finger‐like and sponge‐like structures. With the addition of HBPE, the start pure water contact angle and the mean effective pore size of the membranes decreased, and the J_w increased. For the mechanical properties of the membranes, the breaking strength and the elongation of the membranes also increased. Copyright © 2015 John Wiley & Sons, Ltd.     

Characterization of ultrafiltration membranes. Part II — Mass transport measurements for low and high molecular weight synthetic polymers in water solutions

An experimental study was carried out on the ultrafiltration of two linear synthetic polymers: polyethylene glycol (PEG) and polyvinylpyrrolidone (PVP) in a stirred batch system. Seven fractions of PEG in the molecular weight range 400 to 20,000 and three fractions of PVP (with molecular weights 23,400, 39,000 and 80,000) have been studied using IRIS 3038, IRIS 3042, and UM 10 membranes, in the pressure range 0.2 to 1.2 atm. The permeability ratio α, a dimensionless parameter which measures the deviation of the flux from the “normal” value as given by Darcy's law, was used to analyse the flux-pressure behavior. Rejection data were corrected for concentration polarization using a classical thin-film theory. For aqueous PEG solutions the observed rejection was nil and an increase in applied pressure resulted in more than a proportional increase in permeate flux, i.e. α appears to approach the value 1 asymptotically. This phenomenon was related to the “deformability” of the PEG solute. For aqueous PVP solutions, the data agree with a gel or pre-gel polarization model.     

Impact of gel layer formation on colloid retention in membrane filtration processes

Colloidal particles in the feed streams of membrane filtration processes control membrane fouling rate in many instances. In this study, the non-gelling colloidal Na-alginate and the gelling colloidal Ca-alginate are employed to investigate the significance of gel layer formation in membrane filtration processes in terms of contribution to membrane fouling and supplementary impurity removal. The results show that contribution of colloidal particles to membrane fouling depends on the gelling propensity of the colloids and the operational mode (constant pressure or constant flux) implemented. A small dose of either Na-alginate or Ca-alginate was found to greatly increase membrane fouling rate during constant pressure filtration. Both the resistance to removal by application of shear and the lower susceptibility of the concentration polarization layer to shear resulted in more severe fouling during constant flux filtration in the presence of Ca-alginate assemblages than in the presence of Na-alginate. Apparent channel sizes of the Ca-alginate gel layer were calculated from the material properties of the fouling layer. Incomplete catalase retention highlighted the likely heterogeneity in size of liquid transport pathways. Adsorption also contributed to the trapping of colloidal particles according to the retention behaviour of BSA by the Ca-alginate gel layer. Gel layer formation propensity should be seriously considered for the operation of membrane filtration processes. Two simple methods based on (i) a permeability recovery experiment and (ii) comparison of dead-end filtration behaviour with and without shear application are proposed for evaluation of the gelling propensity of colloidal dispersions.     

Analysis of concentration polarization phenomenon in ultrafiltration under turbulent flow conditions

An ultrafiltration data set previously reported by Gekas and Olund is used to test three concentration polarization models. The data consist of testing eight ultrafiltration membranes representing different polymer materials and molecular weight cut-offs with 0.5 wt% Dextran T10 at 25°C and 0.5 MPa under turbulent flow conditions. The tested concentration polarization models include the modified film theory model, the original film theory model and the Sherwood correlation model. The Chilton-Colburn analogy is the common foundation of the these models.     

凝胶渗透色谱在高聚物分子量测定中的应用

本文综述了近年来凝胶渗透色谱在油溶性和水溶性高聚物分子量测定中的应用,着重分析测试条件对水溶性样品分子量的影响并归纳了解决的办法。同时,介绍了配备紫外可见和示差折光检测器、示差和光散射检测器后凝胶色谱的应用。此外,还概述了几种常见高聚物分子量的标定和校准方法,以便多种方法相互验证,得到较准确的分子量值。     

Preparation and properties of isotactic and syndiotactic poly(methyl methacrylate)s,uniform with respect to molecular weight

Highly isotactic (it-) and highly syndiotactic (st-) poly(methyl methacrylate)s (PMMAs) uniform with respect to molecular weight (stereoregular, uniform PMMAs) were isolated up to the 100mer from it- and st-PMMAs by supercritical fluid chromatography (SFC) and characterized by NMR and mass spectroscopies. Glass transition temperatures (Tg's) of the uniform it- and st-PMMAs were higher than those of the corresponding PMMAs with MWD and with similar molecular weight on average. The Tg values of the uniform it-and st-PMMAs series obeyed the relationship, Tg = Tg∞ - K/M, where M and Tg∞ denote molecular weight and Tg at infinite M, respectively. The reciprocal melting points (1/Tm) of uniform it-PMMA (degree of polymerization, DP = 28–44), obtained from methanol solutions by evaporating the solvent, increased linearly with increasing 1/DP. Extrapolation of the linear relation to 1/DP = 0 gave the Tm of it-PMMA with infinite DP; Tm∞ = 171.1°C. Thermal degradation behavior was studied by thermogravimetry and by SFC analysis of degradation products. In gel-permeation chromatography (GPC) measurements, the it-50mer eluted faster than the st-50mer. Calibration curves for it- and st-PMMAs could be obtained using series of the uniform PMMAs. The instrumental spreading factor determined using it-25mer, it-50mer, st-25mer and st-50mer for our GPC chromatograph was 0.070 ml when the volume of the sample solution was 0.003ml. GPC analysis of a mixture of the it- and st-50mers in tetrahydrofuran indicated formation of a stereocomplex in the solution, and was found quite useful to elucidate the minimum sequence length required for complex formation.     

The dielectric response with respect to the weight distribution of relaxation times

The subjects of this paper are the analytical and partly numerical calculations concerning the problem how the dielectric response in complex solid dielectric materials depends on a statistical distribution of relaxation times.     

Analytical first derivatives of molecular surfaces with respect to nuclear coordinates

We present analytical expressions for the first derivatives of area and other geometrical quantities of polygonal tesserae defined on molecular surfaces. This is a necessary step in the calculation of free energy derivatives with respect to nuclear coordinates for molecular solutes, in the framework of the polarizable continuum method. An application to solute-solvent dispersion energy derivatives is presented. © 1996 by John Wiley & Sons, Inc.     

Effect of molecular weight on microcrystalline structure formation in polymer with perylenediimide side chain

The effect of molecular weight on the molecular aggregation structure of polymers bearing a pendant perylenediimide (PDI) side chain, designated PAc12PDI, was investigated using synchrotron radiation X‐ray diffraction measurements. It was found that depending on molecular weight, either the main chain axis or the side chain axis behaves as the longitudinal axis in fiber samples and was aligned parallel to the fiber axis. A similar phenomenon is present in thin film samples, but was complicated by the additional influence of the interfacial free energy of the side chain group. Even in the case of the polymer with lower molecular weight, the face plane of PDI was found to show both parallel and perpendicular orientations to the substrate (i.e., flat‐on and edge‐on orientations). On the other hand, if the length of the main chain is sufficiently long with respect to the length of the side chain, the face plane of PDI was oriented perpendicular to the substrate, leading to an edge‐on orientation in the thin film. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2275–2283     

Structure and properties of gel-spun ultra-high molecular weight polyethylene fibers with high gel solution concentration

The gel-spun ultra-high molecular weight polyethylene(UHMWPE) fibers were prepared at the industrial production line with different gel solution concentrations of 15 wt%, 18 wt% and 24 wt%. The difference in ultimate structure and mechanical properties of UHMWPE fibers for different gel solution concentrations were analyzed by tensile testing, differential scanning calorimetry(DSC), wide angle X-ray diffraction(WAXD) and small angle X-ray scattering(SAXS). With the increase of gel solution concentration, the ultimate mechanical properties of UHMWPE fibers were decreased and the crystallization and orientation of UHMWPE fibers became inferior. Besides, both the average shish length(〈L _(shish)〉) and shish misorientation(B_φ) of UHMWPE fibers were decreased with the increase of gel solution concentration. In addition, the appropriate increase of spinning temperature led to the further optimization of the ultimate structure and mechanical properties of UHMWPE fibers.     

Effect of molecular weight and degree of deacetylation of chitosan on the formation of oil-in-water emulsions stabilized by surfactant-chitosan membranes

The objective of this study was to establish the influence of polyelectrolyte characteristics (molecular weight and charge density) on the properties of oil-in-water emulsions containing oil droplets surrounded by surfactant-polyelectrolyte layers. A surfactant-stabilized emulsion containing small droplets (d32 approximately 0.3 microm) was prepared by homogenizing 20 wt% corn oil with 80 wt% emulsifier solution (20 mM SDS or 2.5 wt% Tween 20, 100 mM acetate buffer, pH 3) using a high-pressure valve homogenizer. This primary emulsion was then diluted with various chitosan solutions to produce secondary emulsions with a range of chitosan concentrations (3 wt% corn oil, 0-1 wt% chitosan). The influence of the molecular characteristics of chitosan on the properties of these emulsions was examined by using chitosan ingredients with different molecular weights (MW approximately 15, 145, and 200 kDa) and degree of deacetylation (DDA approximately 40, 77, and 92%). The electrical charge and particle size of the secondary emulsions were then measured. Extensive droplet aggregation occurred when the chitosan concentration was below the amount required to saturate the droplet surfaces, but stable emulsions could be formed at higher chitosan concentrations. The zeta-potential and mean diameter (d32) of the particles in the secondary emulsions was not strongly influenced by chitosan MW, however the chitosan with the lowest DDA (40%) produced droplets with smaller mean diameters and zeta-potentials than the other two DDA samples examined. Interestingly, we found that stable multilayer emulsions could be formed by mixing medium or high MW chitosan with an emulsion stabilized by a non-ionic surfactant (Tween 20) due to the fact the initial droplets had some negative charge. The information obtained from this study is useful for preparing emulsions stabilized by multilayer interfacial layers.     

Effect of processing conditions on gel formation in ternary cellulose acetate systems

A series of ternary systems composed of cellulose acetate (CA), N,N-dimethylacetamide (DMA), and water were prepared by varying the mixing temperature and order of component addition with increasing water content. The viscoelastic properties of the resulting ternary systems were measured using steady state and dynamic rheology. The CA/DMA/H₂O mixture formed physical gels at 17.5 and 19 wt% water concentrations after heating to 50 and 70/90 °C, respectively. Gel formation was characterized by the loss of a Newtonian plateau in the steady state as well as the transition of the elastic (G′) modulus becoming greater than the viscous (G″) modulus in the dynamic state. The order of component addition dramatically affected phase behaviour. Adding CA to the DMA/water solution resulted in lower moduli gels and the formation of a two-phase phase separated system at high nonsolvent contents in those prepared at low temperatures. The kinetics of phase separation was improved by subjecting the gels to a thermal treatment of 90 °C. In this case, the gels previously heated at 50 and 70° C showed a one-phase phase separated gel with higher viscous and elastic moduli.     

A general approach to determining the evolution of molecular weight distribution curves of linear polymers undergoing chain scission

A numerical method is developed to compute the development of molecular weight distribution (MWD) curves of linear polymers undergoing chain scission. The method can be applied to complex chain scission kinetics and for arbitrarily complex initial MWD curves. Our method is based on the method of lines (MoL). Different from the existing numerical scheme, we propose the use of logarithmically spaced points. This development ensures the accuracy of the computed MWD curves at low molecular weights, and it does not require a very fine discretization to produce an accurate result.     

Influence of operational parameters on retention of ultra-high molecular weight polystyrenes in thermal field-flow fractionation

Summary The influence of various parameters (concentration of the injected polymer solution, flow rate, temperature gradient, relaxation conditions) on the retention and shape of the fractogram of ultra-high molecular weight polystyrenes in thermal field-flow fractionation was investigated. Under the operating conditions adopted, reproducible oscillations in the peak shape are observed for molecular weights larger than a few millions, especially at relatively high polymer concentration. They are attributed to some hydrodynamic instabilities. The retention of ultra-high molecular weight polystyrenes at high flow rate is strongly dependent on the initial relaxation period. All of the investigated operational variables have a complex effect on the resulting shape of the fractogram. Consequently, the confirmation of the shear-induced focusing of macromolecules across the channel thickness requires further study. Experiments on reinjection of fractions collected after an initial high speed pass through the separation system leads to the conclusion that shear degradation of the ultra-high molecular weight polymers did not occur under the investigated experimental conditions even at the highest flow rates.