Polysulfone — sulfonated poly(ether ether) ketone blend membranes: systematic synthesis and characterisation

The effect of sulfonated poly(ether ether ketone) (SPEEK) in membrane formation and separation properties has been investigated in polysulfone(PSU)/SPEEK/N-methyl-2-pyrrolidinone (NMP) systems. Charged ultrafiltration/nanofiltration membranes were obtained reliably in the range of 0.5–5 wt.% SPEEK in the polymer blend. All PSU/SPEEK blend membranes had substantially higher water flux, salt rejection, porosity and greatly reduced particle adhesion compared to the PSU base membrane. Further, all of these properties varied systematically with variation of SPEEK content. Reproducibility and stability of the membrane properties was excellent. Pore sizes determined from dextran retention data and AFM measurements showed reasonable agreement. Membranes with 5 wt.% SPEEK demonstrated excellent overall properties. Such membranes had very high permeability, 22.6±1.6×10⁻¹¹ m³ s⁻¹ N⁻¹, 0.999 fractional rejection of 4000 Da dextran, 0.65 rejection of 0.001 M NaCl, and only 0.75 mN m⁻¹ adhesion of a 4 μm silica particle. Such membranes are very promising for scale-up of production and testing on real process streams.     

Photo-induced degradation of some flavins in aqueous solution

The blue-light induced photo-degradation of FMN, FAD, riboflavin, lumiflavin, and lumichrome in aqueous solution at pH 8 is studied by measurement of absorption coefficient spectral changes due to continuous excitation at 428 nm. The quantum yields of photo-degradation determined are ϕ_D(riboflavin, pH 8) ≈ 7.8 × 10⁻³, ϕ_D(FMN, pH 5.6) ≈ 7.3 × 10⁻³, ϕ_D(FMN, pH 8) ≈ 4.6 × 10⁻³, ϕ_D(FAD, pH 8) ≈ 3.7 × 10⁻⁴, ϕ_D(lumichrome, pH 8) ≈ 1.8 × 10⁻⁴, and ϕ_D(lumiflavin, pH 8) ⩽ 1.1 × 10⁻⁵. In a mass-spectroscopic analysis, the photo-products of FMN dissolved in water (solution pH is 5.6) were identified to be lumichrome and the lumiflavin derivatives dihydroxymethyllumiflavin, formyllumiflavin, and lumiflavin-hydroxy-acetaldehyde. An absorption and emission spectroscopic characterisation of the primary photoproducts of FMN at pH 8 is carried out.     

The investigation of thermodynamic parameters of kinetic reaction between o-phenylenediamine and gold (III)

A visible spectrophotometric method has been developed for the reaction kinetics of o-phenylenediamine in the presence of gold (III). The method is based on the measurement of the absorbance of the reaction o-phenylenediamine and gold (III). Optimum conditions for the reaction were established as pH 6 at λ = 466 nm.When the reaction kinetic of o-phenylenediamine by gold (III) was investigated, it was observed that the following rate formula was found as ln (A/A₀) = −kt, according to absorbance measurements. The activation energy E_a and Arrhenius constant A were calculated from the Arrhenius equation as 1.009 kJ · mol⁻¹ and 3.46 · 10⁻² s⁻¹, respectively. Other activation thermodynamic parameters, entropy, ΔS (J · mol⁻¹ · K⁻¹), enthalpy, ΔH (kJ · mol⁻¹), Gibbs free energy, ΔG (kJ · mol⁻¹) and equilibrium constant, K_e were calculated at T = (283.2, 303.2, 323.2, and 343.2) K. The study was exothermic due to the decrease of entropy and was a non-spontaneous process during activation.     

Electronic structure and Raman spectroscopy study of dibarium magnesium orthoborate,Ba2Mg(BO3)2

The samples of dibarium magnesium orthoborate Ba₂Mg(BO₃)₂ were synthesized by solid-state reaction. The X-ray diffraction (XRD) patterns and Raman spectra of the samples were collected. Electronic structure and vibrational spectroscopy of Ba₂Mg(BO₃)₂ were systematically investigated by first principle calculation. A direct band gap of 4.4 eV was obtained from the calculated electronic structure results. The top valence band is constructed from O 2p states and the low conduction band mainly consists of Ba 5d states. Raman spectra for Ba₂Mg(BO₃)₂ polycrystalline were obtained at ambient temperature. The factor group analysis results show the total lattice modes are 5E_u + 4A_2u + 5E_g + 4A_1g + 1A_2g + 1A_1u, of which 5E_g + 4A_1g are Raman-active. Furthermore, we obtained the Raman active vibrational modes as well as their eigenfrequencies using first-principle calculation. With the assistance of the first-principle calculation and factor group analysis results, Raman bands of Ba₂Mg(BO₃)₂ were assigned as E_g (42 cm⁻¹), A_1g (85 cm⁻¹), E_g (156 cm⁻¹), E_g (237 cm⁻¹), A_1g (286 cm⁻¹), E_g (564 cm⁻¹), A_1g (761 cm⁻¹), A_1g (909 cm⁻¹), E_g (1165 cm⁻¹). The strongest band at 928 cm⁻¹ in the experimental spectrum is assigned to totally symmetric stretching mode of the BO₃ units.     

The state energy and the displacements of the potential minima of the 2Ag− state in all-trans-β-carotene as determined by fluorescence spectroscopy

The fluorescence spectrum of all-trans-β-carotene was recorded at 170 K. The 1B_u⁺ → 1A_g⁻ fluorescence exhibited clear vibrational structures constituting a mirror image with those of the 1B_u⁺ ← 1A_g⁻ absorption, and the deconvolution of the entire spectrum identified the 2A_g⁻(0) → 1A_g⁻(0) transition at 14 500 cm⁻¹. The displacements of the 1B_u⁺ and 2A_g⁻ potential minima along ν₁ and ν₂ (the CC stretching and C–C stretching normal coordinates, respectively) were determined to be 1.2 and 0.9, and 1.6 and 1.5, respectively. Thus, much larger potential displacements in the 2A_g⁻ state than in the 1Bu⁺ state have been shown.     

The thermodynamic properties of DyBr3(s) and DyI3(s) from T=5 K to their melting temperatures

Low-temperature calorimetric measurements have been performed on DyBr₃(s) in the temperature range (5.5 to 420 K ) and on DyI₃(s) from T=4 K to T=420 K. The data reveal enhanced heat capacities below T=10 K, consisting of a magnetic and an electronic contribution. From the experimental data on DyBr₃(s) a C⁰_p,m (298.15 K) of (102.2±0.2) J·K⁻¹·mol⁻¹ and a value for {S⁰_m (298.15 K) − S⁰_m (5.5 K)} of (205.5±0.5) J·K⁻¹·mol⁻¹, have been obtained. For DyI₃(s), {S⁰_m (298.15 K) − S⁰_m (4 K)} and C⁰_p,m (298.15 K) have been determined as (226.9±0.5) J·K⁻¹·mol⁻¹ and (103.4±0.2) J·K⁻¹·mol⁻¹, respectively. The values for {S⁰_m (5.5 K) − S⁰_m (0)} for DyBr₃(s) and {S⁰_m (4 K) − S⁰_m (0)} for DyI₃(s) have been calculated, giving S⁰_m (298.15 K)=(212.3±0.9) J·K⁻¹·mol⁻¹ in case of DyBr₃(s) and S⁰_m (298.15 K) =(233.1±0.7) J·K⁻¹·mol⁻¹ for DyI₃(s). The high-temperature enthalpy increment has been measured for DyBr₃(s) in the temperature range (525 to 799 K) and for DyI₃(s) in the temperature range (525 to 627 K). From the results obtained and enthalpies of formation from the literature, thermodynamic functions for DyBr₃(s) and DyI₃(s) have been calculated from T→0 to their melting temperatures at 1151.0 K and 1251.5 K, respectively.     

Heat capacities,third-law entropies and thermodynamic functions of the geometrically frustrated antiferromagnetic spinels GeCo2O4 and GeNi2O4 from T=(0 to 400) K

The molar heat capacities of GeCo₂O₄ and GeNi₂O₄, two geometrically frustrated spinels, have been measured in the temperature range from T=(0.5 to 400) K. Anomalies associated with magnetic ordering occur in the heat capacities of both compounds. The transition in GeCo₂O₄ occurs at T=20.6 K while two peaks are found in the heat capacity of GeNi₂O₄, both within the narrow temperature range between 11.4<(T/K)<12.2. Thermodynamic functions have been generated from smoothed fits of the experimental results. At T=298.15 K the standard molar heat capacities are (143.44 ± 0.14) J · K⁻¹ · mol⁻¹ for GeCo₂O₄ and (130.76 ± 0.13) J · K⁻¹ · mol⁻¹ for GeNi₂O₄. The standard molar entropies at T=298.15 K for GeCo₂O₄ and GeNi₂O₄ are (149.20 ± 0.60) J · K⁻¹ · mol⁻¹ and (131.80 ± 0.53) J · K⁻¹ · mol⁻¹ respectively. Above 100 K, the heat capacity of the cobalt compound is significantly higher than that of the nickel compound. The excess heat capacity can be reasonably modeled by the assumption of a Schottky contribution arising from the thermal excitation of electronic states associated with the CO²⁺ ion in a cubic crystal field. The splittings obtained, 230 cm⁻¹ for the four-fold-degenerate first excited state and 610 cm⁻¹ for the six-fold degenerate second excited state, are significantly lower than those observed in pure CoO.     

Conductometric study of some alkali metal halides in (dimethyl sulfoxide + acetonitrile) at T = 298.15 K

Electrolytic conductivities of some alkali metal halides, MX (M⁺ = Li⁺, Na⁺, and K⁺; X^? = Cl^?, Br^?, and I^?), NaBPh₄ and Bu₄NBr have been investigated in (20, 40, and 60) mass% {dimethyl sulfoxide (DMSO) in DMSO + acetonitrile} at T = 298.15 K. The conductance results have been analyzed by the Fuoss-conductance-concentration equation in terms of the limiting molar conductance Λ° the association constant K_A and the association diameter R. The ionic contributions to the limiting molar conductance have been estimated using Bu₄NBPh₄ as the “reference electrolyte”. The association constant K_A tends to increase in the order mass percent 20 < 40 < 60 DMSO in (DMSO + acetonitrile) which is explained by the thermodynamic parameter ΔG° and Walden product Λ°η. The results have been interpreted in terms of ion–solvent interactions and structural changes in the mixed solvents.     

Determination of the standard enthalpy of formation of paratungstate A ion

Enthalpy changes for the reaction of HCl(aq) withNa₂WO₄ (aq) were measured at T =  298.15 K in a HT-1000 calorimeter. The standard enthalpy of reaction for the formation ofW₇O₂₄^6 −  (aq) was calculated on the basis of the experimental results, Δ_rH_m^o(298.15K )  =  − (320.7  ±  1.0)kJ · mol ^− 1. Combining this with the values from the literature led to the standard enthalpy of formation of W₇O₂₄^6 − (aq),Δ_fH_m^o (298.15 K)  =  − 6689.8 kJ · mol ^− 1.     

Thermodynamic properties of Na2Ti6O13 and Na2Ti3O7: electrochemical and calorimetric determination

Standard values of Gibbs free energy, entropy, and enthalpy of Na₂Ti₆O₁₃ and Na₂Ti₃O₇ were determined by evaluating emf-measurements of thermodynamically defined solid state electrochemical cells based on a Na–β″-alumina electrolyte. The central part of the anodic half cell consisted of Na₂CO₃, while two appropriate coexisting phases of the ternary system Na–Ti–O are used as cathodic materials. The cell was placed in an atmosphere containing CO₂ and O₂. By combining the results of emf-measurements in the temperature range of 573⩽T/K⩽1023 and of adiabatic calorimetric measurements of the heat capacities in the low-temperature region 15⩽T/K⩽300, the thermodynamic data were determined for a wide temperature range of 15⩽T/K⩽1100. The standard molar enthalpy of formation and standard molar entropy at T=298.15 K as determined by emf-measurements are Δ_fH_m⁰=(−6277.9±6.5) kJ · mol⁻¹ and S_m⁰=(404.6±5.3) J · mol⁻¹ · K⁻¹ for Na₂Ti₆O₁₃ and Δ_fH_m⁰=(−3459.2±3.8) kJ · mol⁻¹ and S_m⁰=(227.8±3.7) J · mol⁻¹ · K⁻¹ for Na₂Ti₃O₇. The standard molar entropy at T=298.15 K obtained from low-temperature calorimetry is S_m⁰=399.7 J · mol⁻¹ · K⁻¹ and S_m⁰=229.4 J · mol⁻¹ · K⁻¹ for Na₂Ti₆O₁₃ and Na₂Ti₃O₇, respectively. The phase widths with respect to Na₂O content were studied by using a Na₂O-titration technique.     

The vapour pressures of saturated aqueous solutions of magnesium,calcium, nickel and zinc acetates and molar enthalpies of solution of magnesium,calcium, zinc and lead acetates

Vapour pressures of water over saturated solutions of magnesium, calcium, nickel and zinc acetates were determined as a function of temperature. The vapour pressures served to evaluate the water activities, osmotic coefficients and molar enthalpies of vaporization. Molar enthalpies of solution of magnesium acetate tetrahydrate,Δ_solH_m (T =  294.71K ;m =  0.01 mol · kg ^− 1)  =  − (15.65  ±  0.97)kJ · mol ^− 1; calcium acetate,Δ_solH_m (T =  297.18K ;m =  0.01 mol · kg ^− 1)  =  − (28.15  ±  0.28)kJ · mol ^− 1; zinc acetate dihydrate,Δ_solH_m (T =  297.36K ;m =  0.01 mol · kg ^− 1)  =  − (22.49  ±  0.90)kJ · mol ^− 1and lead acetate trihydrate,Δ_solH_m (T =  297.36K ;m =  0.0086 mol · kg ^− 1)  =  (22.46  ±  0.94)kJ · mol ^− 1, were determined calorimetrically.     

VO2 nano-sheet negative electrodes for lithium-ion batteries

Vanadium dioxide (VO₂) nano-sheets were directly synthesized via a continuous hydrothermal process and were investigated as electrodes in a wide potential range of 0.05–3 V vs. Li/Li⁺. The nano-sheets showed excellent capacity retention, with a specific capacity of 350 mAh g^− 1 at an applied current of 0.1 A g^− 1 and 95 mAh g^− 1 at 10 A g^− 1. Further electrochemical testing suggested that a significant proportion of the charge storage in the cells was due to pseudocapacitive processes.     

Heat capacities,third-law entropies and thermodynamic functions of the negative thermal expansion material Zn2GeO4 from T=(0 to 400) K

The molar heat capacity of Zn₂GeO₄, a material which exhibits negative thermal expansion below ambient temperatures, has been measured in the temperature range 0.5⩽(T/K)⩽400. At T=298.15 K, the standard molar heat capacity is (131.86 ± 0.26) J · K⁻¹ · mol⁻¹. Thermodynamic functions have been generated from smoothed fits of the experimental results. The standard molar entropy at T=298.15 K is (145.12 ± 0.29) J · K⁻¹ · mol⁻¹. The existence of low-energy modes is supported by the excess heat capacity in Zn₂GeO₄ compared to the sums of the constituent binary oxides.     

Development of micro-tubular SOFCs with an improved performance via nano-Ag impregnation for intermediate temperature operation

Micro-tubular solid-oxide fuel cell consisting of a 10-μm thick (ZrO₂)_0.89(Sc₂O₃)_0.1(CeO₂)_0.01 (ScSZ) electrolyte on a support NiO/(ScSZ) anode (1.8 mm diameter, 200 μm wall thickness) with a Ce_0.8Gd_0.2O_1.9 (GDC) buffer-layer and a La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ (LSCF)/GDC functional cathode has been developed for intermediate temperature operation. The functional cathode was in situ formed by impregnating the well-dispersed nano-Ag particles into the porous LSCF/GDC layer using a citrate method. The cells yielded maximum power densities of 1.06 W cm⁻² (1.43 A cm⁻², 0.74 V), 0.98 W cm⁻² (1.78 A cm⁻², 0.55 V) and 0.49 W cm⁻² (1.44 A cm⁻², 0.34 V), at 650, 600 and 550 °C, respectively.     

A calorimetric and thermodynamic investigation of A2[(UO2)2(MoO4)O2] compounds with A = K and Rb and calculated phase relations in the system (K2MoO4 + UO3 + H2O)

A calorimetric and thermodynamic investigation of two alkali-metal uranyl molybdates with general composition A₂[(UO₂)₂(MoO₄)O₂], where A = K and Rb, was performed. Both phases were synthesized by solid-state sintering of a mixture of potassium or rubidium nitrate, molybdenum (VI) oxide and gamma-uranium (VI) oxide at high temperatures. The synthetic products were characterised by X-ray powder diffraction and X-ray fluorescence methods. The enthalpy of formation of K₂[(UO₂)₂(MoO₄)O₂] was determined using HF-solution calorimetry giving Δ_fH° (T = 298 K, K₂[(UO₂)₂(MoO₄)O₂], cr) = −(4018 ± 8) kJ · mol⁻¹. The low-temperature heat capacity, С_р°, was measured using adiabatic calorimetry from T = (7 to 335) K for K₂[(UO₂)₂(MoO₄)O₂] and from T = (7 to 326) K for Rb₂[(UO₂)₂(MoO₄)O₂]. Using these С_р° values, the third law entropy at T = 298.15 K, S°, is calculated as (374 ± 1) J · K⁻¹ · mol⁻¹ for K₂[(UO₂)₂(MoO₄)O₂] and (390 ± 1) J · K⁻¹ · mol⁻¹ for Rb₂[(UO₂)₂(MoO₄)O₂]. These new experimental results, together with literature data, are used to calculate the Gibbs energy of formation, Δ_fG°, for both phases giving: Δ_fG° (T = 298 K, K₂[(UO₂)₂(MoO₄)O₂], cr) = (−3747 ± 8) kJ · mol⁻¹ and Δ_fG° (T = 298 K, Rb₂[(UO₂)₂(MoO₄)], cr) = −3736 ± 5 kJ · mol⁻¹. Smoothed С_р°(Т) values between 0 K and 320 K are presented, along with values for S° and the functions [H°(T) − H°(0)] and [G°(T) − H°(0)], for both phases. The stability behaviour of various solid phases and solution complexes in the (K₂MoO₄ + UO₃ + H₂O) system with and without CO₂ at T = 298 K was investigated by thermodynamic model calculations using the Gibbs energy minimisation approach.     

Perovskite-type oxides for high-temperature oxygen separation membranes

Oxygen permeation through dense ceramic membranes of perovskite-like SrCo_0.9−xFe_0.1Cr_xO_3−δ (x = 0.01–0.05), Sr_1−x−yLn_xCoO_3−δ(Ln = La, Nd, Sm, Gd; x = 0.30–0.35; y = 0–0.10), SrCo_1−xTi_xO_3−δ (x = 0.05–0.20) and LaM_1−xNi_xO_3−δ (M = Ga, Co, Fe; x = 0–0.6) was studied. The SrCoO_3−δ-based solid solutions with cubic perovskite structure were found to exhibit highest permeation fluxes compared to other membranes. However, high thermal expansion coefficients and interaction with gas species such as carbon dioxide may complicate the employment of SrCoO_3−δ membranes for oxygen separation membranes. Alternatively, the LaGa_1−xNi_xO_3−δ (x = 0.2–0.5) perovskites, having significant permeation fluxes as well as thermal expansion coefficients in the range of (10.8–11.6) × 10⁻⁶ K⁻¹, were demonstrated to be suitable as membrane materials at oxygen pressures from 1 × 10⁻² to 2 × 10⁴ Pa. Testing oxygen permeation at oxygen partial pressures of 1–60 atm showed that only oxides with a high oxygen deficiency such as SrCo_0.85Ti_0.15F_3−δ possess sufficient oxygen permeation fluxes. The oxygen permeability of perovskites on the basis of LaGaO₃ and LaCoO_3−δ was found to be negligible at oxygen pressures above 15 atm, caused by low oxygen vacancy concentration and ionic conductivity of such ceramic materials.     

Catalytic effect of CTAB on the interaction of dipeptide glycyl-tyrosine (Gly-Tyr) with ninhydrin

The effect of cationic micelles of cetyltrimethylammonium bromide (CTAB) on the interaction of dipeptide glycyl-tyrosine (Gly-Tyr) with ninhydrin under varying conditions has been studied spectrophotometrically at 70 °C and pH 5.0. The reaction followed first- and fractional-order kinetics with respect to [Gly-Tyr] and [ninhydrin], respectively. Increase in total concentration of CTAB from 0 to 70 × 10⁻³ mol dm⁻³ resulted in an increase in the pseudo-first-order rate constant (k_ψ) by a factor of ca. 3. Quantitative kinetic analysis of k_ψ − [CTAB] data was performed on the basis of pseudo-phase model of the micelles (proposed by Menger and Portnoy and developed by Bunton) and Piszkiewicz model. A possible mechanism has been proposed and the kinetic data have been used to evaluate the micellar binding constants K_S (268 mol⁻¹ dm³ for Gly-Tyr) and K_N (64 mol⁻¹ dm³ for ninhydrin).     

A self-assembled monolayer based electrochemical immunosensor for detection of leukemia K562A cells

A novel strategy to quantify the cell number of leukemia K562A cells using electrochemical immunosensor was developed by effective surface immunoreaction between P-glycoprotein (P-gp) on cell membrane and P-gp mouse monoclonal antibody bound on an epoxysilane monolayer modified glassy carbon electrode. The surface morphologies of the epoxysilane monolayer and the bound antibodies were studied with atomic force microscopy. The binding of target K562A cells onto the immobilized antibodies increased the electron-transfer impedance of electrochemical probe, which depended linearly on the cell concentration in the range of 5.0 × 10⁴–1.0 × 10⁷ cells mL⁻¹. The detection limit of the immunosensor was 7.1 × 10³ cells mL⁻¹. The proposed strategy showed acceptable reproducibility with an RSD of 3.4% for the linear slope and good precision with the RSD of 3.7% and 3.0% examined at the cell concentrations of 2.0 × 10⁶ and 1.0 × 10⁷ cells mL⁻¹.     

Enantiomeric recognition of amino acid derivatives by chiral schiff bases of calix[4]arene

Novel calix[4]arene Schiff bases bearing chiral substituents both on the upper and the lower rims have been developed. These chiral receptors exhibit good chiral recognition ability towards α-amino acid ester hydrochlorides (up to K_D/K_L = 4.36, ΔΔG₀ = − 3.65 kJ mol⁻¹) in CHCl₃. The molecular recognition abilities and enantioselectivities for guests are also discussed from a thermodynamic point of view.     

Achieving high electrode specific capacitance with materials of low mass specific capacitance: Potentiostatically grown thick micro-nanoporous PEDOT films

Electrode materials for supercapacitors are at present commonly evaluated and selected by their mass specific capacitance (C_M, F g⁻¹). However, using only this parameter may be a misleading practice because the electrode capacitance also depends on kinetics, and may not increase simply by increasing material mass. It is therefore important to complement C_M by the practically accessible electrode specific capacitance (C_E, F cm⁻²) in material selection. Poly[3,4-ethylene-dioxythiophene] (PEDOT) has a mass specific capacitance lower than other common conducting polymers, e.g. polyaniline. However, as demonstrated in this communication, this polymer can be potentiostatically grown to very thick films (up to 0.5 mm) that were porous at both micro- and nanometer scales. Measured by both cyclic voltammetry and electrochemical impedance spectrometry, these thick PEDOT films exhibited electrode specific capacitance (C_E, F cm⁻²) increasing linearly with the film deposition charge, approaching 5 F cm⁻², which is currently the highest amongst all reported materials.