Spectral interferences in the determination of trace elements in environmental materials by inductively coupled plasma atomic emission spectrometry

This paper deals with spectral interferences in inductively coupled plasma atomic emission spectrometry (ICP-AES) encountered with environmental materials. These samples normally contain high concentrations of aluminium, calcium, magnesium, iron, titanium, potassium and sodium. The investigations cover: (a) spectral data for Al, Ca, Mg, Fe, Ti, K and Na as interferents for 200 pm wide windows centred (±100 pm) around the prominent lines of As, B, Ba, Be, Cd, Cr, Cu, Hg, Mn, P, Pb, Sb, Se, Sn, Tl, U and Zn; (b) a data base of Q-values for line interference [Q_Ij(λ_a)] and Q-values for wing background interference [Q_Wj(Δλ_a)] for two values of the excitation temperature 6200 K and 7200 K. The lines free or negligibly influenced by line interference were selected for analyte determination. Q-values were used for calculation of correction factors under a spectral line without the measurement of a reference blank at the wavelength of the prominent analysis lines. The accuracy of ICP-AES with the Q-concept as a basic methodology is checked by the analysis of a certified reference material IAEA/Sediment SD-N-1/2/. The precision of the method is characterised by an RSD of 0.6–1.7%. Extraction of trace elements soluble in aqua regia was used as a decomposition method. This article is an electronic publication in Spectrochimica Acta Electronica (SAE), a section of Spectrochimica Acta, Part B (SAB). The hardcopy text is accompanied by an electronic archive, stored on the SAE homepage at http://www.elsevier.nl/locate/sabe. The archive contains the tabular material of this article in electronic form.     

Flame AAS determination of dopants and trace metal impurities in single crystals of potassium titanylphosphate

A flame AAS method is used for the determination of dopants and impurities in potassium titanylphosphate (KTP) single crystals. Sample digestion using sulphuric acid and hydrofluoric acid is proposed as being the most appropriate procedure. The effect of major and minor components in the sample solution on the analytical signal is studied. The content of the dopants Cr, Mn and Ni (at a level of about 1 mg g(-1)) as well as the content of the impurities Fe, Na, Mg, W and Al (from 4 mug g(-1), depending on the trace metal) in the KTP single crystals is determined. The precision of the method is characterized by a relative standard deviation of 3-10%. The accuracy is checked by comparison with ICP-AES data for the trace element content in the KTP single crystals.     

Simultaneous determination of the constituents in Al-Ge-Si alloys by inductively coupled plasma atomic emission spectrometry

An accurate method for determination of the constituents Ge, Si, In and Mg in Al–Ge–Si based compact alloys and foil materials by ICP atomic emission spectrometry is developed. The material samples were dissolved in nitric acid–hydrofluoric acid. Optimum parameters for the simultaneous measurement of the constituent elements are worked out. To compensate the time determined sensitivity fluctuations the analytical signal was corrected by a special procedure of external standardization.     

Simultaneous determination of the constituents in Al-Ge-Si alloys by inductively coupled plasma atomic emission spectrometry

An accurate method for determination of the constituents Ge, Si, In and Mg in Al-Ge-Si based compact alloys and foil materials by ICP atomic emission spectrometry is developed. The material samples were dissolved in nitric acid-hydrofluoric acid. Optimum parameters for the simultaneous measurement of the constituent elements are worked out. To compensate the time determined sensitivity fluctuations the analytical signal was corrected by a special procedure of external standardization.     

ICP-AES法测定方铅矿中多元素的方法研究

采用电感耦合等离子体原子发射光谱法(ICP-AES)进行方铅矿中多元素同时测定.通过对方铅矿样品化学处理试验建立了HCl-NH4Cl-HNO3的溶矿体系.本体系采用基体匹配、背景系数和元素干扰系数校正及元素内标法确定了最佳综合实验测试条件.本实验建立的ICP-AES法同时测定方铅矿中镉、钴、铜、铁、铟、铅、锌7种元素的方法,本方法测量相对误差RE (n=8)为1.50%～7.50%,相对标准偏差RSD (n=8)为1.7%～5.7%.经国家一级标准物质GBW 07269分析验证可以满足方铅矿单矿物样品的分析要求.     

Tandem on-line continuous separation and determination of arsenic by inductively coupled plasma atomic emission spectrometry

The principle of tandem on-line continuous separation techniques as an alternative means of introducing samples into plasmas was applied to the development of a sensitive, selective and convenient method for the determination of arsenic by inductively coupled plasma atomic emission spectrometry (ICP-AES). Arsenic is continuously extracted as AsI₃ into xylene from the sample dissolved in 0.1 M potassium iodide solution in 7.2 M hydrochloric acid. The xylene phase (containing the analyte) is continuously mixed on-line with NaBH₄ in dimethylformamide and acetic acid solutions. Arsine is thus continuously generated directly from the organic phase and is separated in a gas—liquid separation device which prevents most of the xylene phase vapour from reaching the ICP. The system was optimized for the continuous extraction of AsI₃, the direct generation of arsine from xylene and the final ICP determination of arsenic. Finally, the tandem on-line continuous separation ICP detection system was applied to the determination of arsenic in real samples (white metal, cast iron, cupro-nickel and orchard leaves standard materials). Very good agreement between the experimental results and the certified values was obtained.     

A helium inductively coupled plasma for atomic emission spectrometry

An annular helium inductively coupled plasma (He ICP) was generated at atmospheric pressure. No external cooling was used to stabilize the plasma. Aqueous solution was injected into the plasma without any difficulty. Preliminary results revealed that the annular He ICP was capable of exciting elements such as Cl and Br which possess high excitation energies. Atomic emission detection limits for Cl and Br were improved by factors of 63 and 34, respectively, as compared to the results obtained from the argon inductively coupled plasma. The excitation temperature of the annular He ICP (4180 K) was less than that of an Ar ICP (5570 K).     

Quality of calibration in inductively coupled plasma atomic emission spectrometry

Calibration is a crucial step during the whole analytical process. A procedure is suggested to assess the quality of linear regression used for the calibration graph, based on the use of confidence limits for the concentration, as the regression coefficient is not appropriate for this purpose. This procedure has been applied to inductively coupled plasma atomic emission spectrometry. It indicates that the use of only three standards should be discouraged because of unacceptably high confidence limits for the concentration. Moreover, use of weighted regression is more adequate in performing the least squares method and provides more constant confidence limits over the concentration range used to construct the calibration graph. This procedure could be easily added to any commercially available ICP system software.     

Influence of hydrogen gas over the interference of acids in inductively coupled plasma atomic emission spectrometry

The effect of hydrogen gas on the plasma and its influence on acid interferences in plasma atomic emission spectrometry was studied. The study was performed with HCl and HNO₃ in the concentration range of 0–2 mol l⁻¹. Vanadium and magnesium were used as test elements, the study was extended to other several elements. The effects of hydrogen gas on the plasma were studied by measuring excitation temperature, electron number density and the ionic-to-atomic line intensity ratio. The net effect of hydrogen was an increase in electron density and ionic to atomic line intensity ratio. A small increase in the excitation temperature was observed. The signal suppression for ionic lines causes by mineral acid was reduced when small amounts of hydrogen was introduced into the plasma as sheathing gas. This effect was attributed to the increase in plasma electron density.     

Analytical control of the preparation of single crystal materials by inductively coupled plasma atomic emission spectrometry

The present paper shows that inductively coupled plasma atomic emission spectrometry (ICP-AES) and the Q concept, in accordance with Boumans and Vrakking [Spectrochim. Acta Part B 43 (1988) 69] can be used in the determination of a large number of dopants with different characteristics (charge and ionic radius) in the single crystals of potassium titanylphosphate [KTiOPO₄], some of its structural analogues and potassium gadolinium tungstate [KGd (WO₄)₂]. The basic conclusion from the analytical data obtained in this work is that the incorporation of Me⁺, Me²⁺, Me³⁺, Me⁴⁺ and Me⁵⁺ ions in the crystal lattice depend on its ionic radii. The effect of the ionic charge of the dopant ions is negligible. The light on the regularities of dopant incorporation in the crystal lattice was thrown and hence on the possibilities of modifying the properties of the single crystal materials.     

On-line-sorption preconcentration and inductively coupled plasma atomic emission spectrometry determination of rare earth elements

The system for on-line microcolumn sorption preconcentration and inductively coupled plasma atomic emission spectrometry determination of 14 rare earth elements (REEs) is described. Aminocarboxylic sorbents of different structure are used. Preconcentration of REEs from the 20 ml of sample solution and elution with 210 μl of 1 mol l⁻¹ HCl results in an enrichment factor of 99. The detection limit of REEs is about n × 0.1 μg l⁻¹ (RSD 3–5%). The possibility of simultaneous REE determination in complicated solutions is demonstrated.     

Spectral interpretation and interference correction in inductively coupled plasma mass spectrometry

To tackle the several problematic polyatomic interferences in inductively coupled plasma mass spectrometry (ICP-MS), we have developed a software approach based on data reduction of the measured total mass spectrum through multicomponent analysis (MCA). The approach leans on a working knowledge of interferents that are likely to be encountered in a sample matrix, which composition is known by virtue of the total mass spectrum and knowledge of applied solvents. The full isotopic patterns for all elements and expected interferents are used in the modelling MCA matrix of 250 masses × 105 species at maximum. Polyatomic abundances are calculated by the software. Since all species are modelled fundamentally through their known natural abundances, the MCA matrix can be manipulated and reprocessed until interpretation of the mass spectrum and, hence, interference correction are optimal. The optimum is attained by use of the bar graph and calculation modes of the PC software and criteria for properly found isotopic patterns. With optimized models stored in the data base, the user may routinely process samples in one go, and operate the ICP-MS system in a true all-element mode. Use of elemental equations or measurement of large multivariate calibration sets and pure component solutions are superfluous. Data reduction is solely based on the information about the isotopic patterns, present in the measured mass spectrum itself. As a result, in the case of interferences, detection limits may be lowered by one to two orders of magnitude. The approach is illustrated with an industrial example of Hf determined in NdFeB, and with an environmental example. Here, a suite of elements over the 50–82 amu mass range has been determined in different salt matrices in ground water.     

Silicon determination by inductively coupled plasma atomic emission spectrometry after generation of volatile silicon tetrafluoride

A method for the determination of silicon by inductively coupled plasma atomic emission spectrometry (ICP-AES) is described. The procedure is based on a discontinuous generation of volatile silicon tetrafluoride in concentrated sulphuric acid medium after injecting 125 μl of 0.1%, w/v sodium fluoride solution into 100 μl of the sample. The gaseous silicon tetrafluoride is fed directly into the ICP torch by a flow of 250 ml min⁻¹ Ar carrier gas. The calibration curve was linear up to at least 100 μg ml⁻¹ of Si(IV) and the absolute detection limit was 9.8 ng working with a solution volume of 100 μl. The relative standard deviation for six measurements of 10 μg ml⁻¹ of Si(IV) was 2.32%. The method was applied to the determination of silicon in water and iron ores.     

Determination of phosphorus in fertilizers by inductively coupled plasma atomic emission spectrometry

An inductively coupled plasma atomic emission spectrometry (ICP-AES) method was developed for the determination of phosphorus in fertilizers. Total phosphorus, direct extraction available phosphorus (EDTA), and water-soluble phosphorus, reported as phosphorus pentoxide (P205), in 15 Magruder check fertilizers were measured by ICP-AES, and the results were compared with those obtained by the AOAC official method. Five analytical wavelengths of phosphorus, 177.499, 178.287, 213.618, 214.914, and 253.565 nm, were tested for the determination of phosphorus in fertilizers, and their detection limits were obtained. Acid effects of perchloric acid and possible matrix effects of aluminum, calcium, magnesium, potassium, and sodium were negligible for phosphorus determination. Wavelength 213.618 nm was the best analytical wavelength for phosphorus determination by all 3 sample preparation methods for the selected Magruder fertilizers. The results demonstrated that the accuracy and precision of the ICP-AES method were comparable with those of the official methods.     

Analysis of yttrium aluminium borate crystals by solution-based methods: inductively coupled plasma atomic emission spectrometry and flame atomic absorption spectrometry

Comparative analysis of yttrium aluminium borate (YAB) /YAl₃(BO₃)₄/ optical single crystals was performed by flame atomic absorption spectrometry (FAAS) and inductively coupled plasma atomic emission spectrometry (ICP-AES) methods for Cr, Dy, Er, Yb, Y, Al, B and Mo. The dopant element, Ce, could be determined only by the ICP-AES method at the required concentration level. The powdered crystal samples were fused with lithium metaborate (LiBO₂) at 950 °C in a platinum crucible and then dissolved in 6 mol l⁻¹ HCl. Although this fusion-dissolution procedure proved to be simple and effective, the quantitative determination of B—as the matrix element in samples—was handicapped by the B content of the fusing reagent. For the FAAS method, with the use of nitrous oxide–acetylene flame, cesium chloride ionization buffer and lanthanum chloride releasing agent [0.1+0.2% (m/v), respectively] were applied. These agents enhanced the atomic absorption signals of Cr, Dy, Er, Mo, Yb and Y, whereas no change of sensitivity was resulted in for Al and B. A fairly good agreement was found between the results of the two alternative spectrochemical methods. The predicted stoichiometry of the crystals was also well approximated indicating the reliability of the crystal growth technology applied.     

Carbon-related matrix effects in inductively coupled plasma atomic emission spectrometry

In Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES), it has been observed that the emission intensity of some atomic lines is enhanced or depressed by the presence of carbon in the matrix. The goal of this work was to investigate the origin and magnitude of the carbon-related matrix effects in ICP-AES. To this end, the influence of the carbon concentration and source (i.e. glycerol, citric acid and potassium hydrogen phthalate), the experimental conditions and sample introduction system on the aerosol characteristics and transport, plasma excitation conditions and the emission intensity of several atomic and ionic lines of a total of 15 elements has been studied. Results indicate that carbon related matrix effects do not depend on the carbon source and they become more severe when the amount of carbon loaded into the plasma increases, i.e., when using: (i) carbon concentrations higher than 5 g L^− 1; (ii) high sample uptake rates; and (iii) efficient sample introduction systems. Thus, when introducing carbon into the plasma, the emission intensity of atomic lines with excitation energies below 6 eV is depressed (up to 15%) whereas the emission intensity of atomic lines of higher excitation energies (i.e. As and Se) are enhanced (up to 30%). The emission intensity of the ionic lines is not affected by the presence of carbon. The origin of the carbon-related interferences on the emission intensity of atomic lines is related to changes in the line excitation mechanism since the carbon containing solutions show the same aerosol characteristics and transport efficiencies as the corresponding aqueous solutions. Based on the previous findings, a calibration approach for the accurate determination of Se in a Se-enriched yeast certified material (SELM-1) has been proposed.     

Some hydride generation inter-element interference studies utilizing atomic absorption and inductively coupled plasma emission spectrometry

Three commercially available hydride generation devices have been used in conjunction with atomic absorption spectrometry and inductively coupled plasma emission spectrometry to study the possible inter-element interferences from fifty elements. Nineteen of these elements caused signal reductions of at least 10%. These interferences were reduced (drastically in some cases) by an appropriate choice of hydride generation system and by manipulation of the acid strength.     

Line selection and interference correction for the analysis of tungsten alloy by inductively coupled plasma atomic emission spectrometry

A method for the analysis of tungsten alloy to determine selected elements using inductively coupled plasma atomic emission spectroscopy is described, with emphasis on line selection and spectral interference. The spectral interference coefficients were calculated for the spectral lines of selected major and trace elements. These values were used to select analytical lines and to calibrate concentrtions of the analytes. The detection limits of the elements for this method were determined and compared with those obtained by flame atomic absorption spectrometry and direct current carbon are emission spectrometry. The results indicated that the detection limits for all of the elements determined by the proposed method are significantly better than those obtained by other techniques. In this study, the analytical reliability of the proposed method was estimated by comparison of the analytical data for the two types of tungsten alloys produced by the Korean Tungsten Company with those obtained by the matrix matching method and the results indicated that the accuracy of multi-element analysis is satisfactory.     

Antimony(V) volatilization with bromide and determination by inductively coupled plasma atomic emission spectrometry

Antimony(V) is volatilized by reaction with potassium bromide in concentrated sulfuric acid media. After volatilization, the gases can be transported to an inductively coupled plasma spectrometer for atomic emission of antimony and its analytical determination. The influent factors, concentrated sulfuric acid volume, concentration and volume of the potassium bromide aqueous solution and carrier gas flow were investigated and optimized using different alternatives. A detection limit of 48 ng ml⁻¹ of Sb was achieved under the optimized conditions with a precision of 7.6% and the calibration graph was linear from 0.10 to 10.0 μg ml⁻¹ for a sample injection of 130 μl.The study of interferences from common cations and anions revealed a good tolerance for most ions, although there was a significant improvement in Sb(V) volatility when As(III) was present. Furthermore, the As(III) sensitization was only produced with Sb(V) species, while the volatility of the Sb(III) bromide species was unaltered.The method was applied to the determination of Sb in real river waters. The results were checked using alternative atomic spectroscopy methods.     

Preconcentration of platinum group metals on modified silicagel and their determination by inductively coupled plasma atomic emission spectrometry and inductively coupled plasma mass spectrometry in airborne particulates

Modified silicagel (C18) was studied for separation and preconcentration of platinum group metals (Ru, Rh, Pd, Os, Ir and Pt) as ion associates of their chlorocomplexes with cation of onium salt N(1-carbaethoxypentadecyl)-trimethyl ammonium bromide. Sample containing HCl and the onium salt was pumped through the column. After elution with ethanol the eluate was evaporated in the presence of HCl. Resulting aqueous solutions were analysed with inductively coupled plasma atomic emission spectrometry (ICP-AES) and inductively coupled plasma mass spectrometry (ICP-MS). Recovery values of 1-20 mug Pt and Pd from 50 ml of synthetic pure solution were 100+/-3 and 100+/-1%, respectively, however, they diminished with increasing sample volume and in the presence of the real sample matrix or nitrate ions. Samples of engine soot (NIES No. 8), decomposed by low pressure oxygen high-frequency plasma, and airborne particulates from dust filters of meteorological stations, leached with HNO(3) and H(2)O(2), were analysed. A reasonable agreement was found between ICP-MS and ICP-AES results for airborne dust samples and the values comparable with those in literature were determined in NIES No. 8.