Fluorenyl cardo copolyimides containing poly(ethylene oxide) segments: Synthesis,characterization, and evaluation of properties

A set of new block copolyimides containing fluorenyl cardo moieties (FR) in the polyimide blocks and poly(ethylene oxide) (PEO) sequences has been prepared using the two‐step method of polyimide synthesis. The combination of both moieties led to novel copolyimides with good solubility in a variety of solvents, which could easily be processed into films. Copolyimides with PEO content from 30 to 56 wt % were amorphous, showed good mechanical properties, and absorbed less water than other PEO‐containing polyimides previously reported. Copolyimides with higher PEO content (60 and 65%) showed crystallinity and yielded soft films. All of the copolymers showed two glass transition temperatures, the first one around ?25 °C attributed to the PEO segments, and the second one at much higher temperature, which corresponded to the polyimide domains. The thermal degradation occurred in two steps, the first one being associated with the degradation of the PEO segments and the second one with the generalized aromatic polyimide decomposition. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 8170–8178, 2008     

Synthesis and characterization of organosoluble aliphatic-aromatic copolyimides based on cycloaliphatic dianhydride

A series of aliphatic-aromatic polyimides have been synthesized. These polyimides were prepared by high-temperature polycondensation of the aliphatic diamines: 1,4-diaminobutane, 1,6-diaminohexane, 1,7-diaminoheptane, 1,9-diaminononane, 1,10-diaminodecane, 1,12-diaminododecane and 4,4^′-methylenebis(2,6-dimethylaniline) with 1,2,3,4-cyclopentanetetracarboxylic dianhydride. Various ratios of diamines (aromatic:aliphatic) have been applied for preparation of copolyimides. Polycondensation proceeded at 190 °C and produced copolyimides with reduced viscosities up to 0.92 dl/g. The polyimides were soluble in a wide range of organic, common solvents and showed high-thermal stability. In most cases these polymers formed flexible films which presented excellent transparency.     

Positron annihilation properties of copolyimides and copolyamides with microphase‐separated structures

The positron annihilation lifetime (PAL) of a series of copolyimides and copolyamides with microphase‐separated structures was measured to investigate the effects of different hard‐segment polymers on the PAL properties of soft‐segment domains of poly(dimethyl‐siloxane) (PDMS) and poly(ethylene oxide) (PEO). The lifetime (τ₃) and intensity (I₃) of the long‐lived component are given as a function of the PDMS or PEO content for a series of copolymers, of which the density roughly obeys the additive rule except for the PDMS‐segmented copolyamides. The PDMS‐segmented copolyimides and copolyamides show much smaller I₃ values than those estimated from the additive rule. The lifetime distribution of the long‐lived component for the PDMS‐segmented copolyamides is composed of two components. The longer‐lifetime component is attributed to pure PDMS domains, and the shorter‐lifetime component is attributed to the polyamide domains, intermediate phases, and PDMS domains containing small amounts of short amide blocks. Despite the high PDMS content, the latter component is rather large. Thus, the positronium formation in the PDMS domains of the copolyimides and copolyamides is effectively reduced. This can be explained by the combination of the difference in the electron affinity of the PDMS and polyimide or polyamide segments and the incomplete phase separation. The PEO‐segmented copolyimides show much smaller I₃ values than those predicted from the additive rule. This is likely attributable to the effects of the intermediate phases. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1123–1132, 2000     

SYNTHESIS AND CHARACTERIZATION OF AMPHIPHILIC GRAFT COPOLYMER CONTAINING MICROPHASE SEPARATED AND LONG POLY(ETHYLENE OXIDE) SIDE CHAIN STRUCTURES**

Acryloyl terminated Poly (ethyleneoxide)macromonomers (PEO-A) with different PEO chain lengths have been prepared by deactivation of PEO alkoxide with acryloyl chloride. A new kind of amphiphilic polystyrene-g-poly (ethylene oxide)graft copolymer containing both microphase separated and PEO side chain structures has been synthesized from radical copolymerization of PEO-A macromonomer with styrene. After careful purification by a newly-developed method called "selective dissolution', the well-defined structure of the purified copolymers was confirmed by IR, ~1H-NMR and GPC. Various experimental parameters controlling the copolymerization were studied in detail. The results indicated that the feed ratio of styrene to macromonomer(S/M) was the most important determining factor for the composition of the copolymers. A detailed "comb- model" was proposed to describe the molecular structure of the graft copolymers. Finally, this amphiphilic graft copolymers may readily form microphase separated structures as clearly indicated by transmission electron microscopy.     

Amphiphilic polymer gel electrolytes. I. preparation of gels based on poly(ethylene oxide) graft copolymers containing different ionophobic groups

Amphiphilic graft copolymers were prepared via the radical copolymerization of poly(ethylene oxide) (PEO) macromonomers with fluorocarbon or hydrocarbon acrylates in toluene with 2,2′‐azobisisobutyronitrile (AIBN) as an initiator. ¹H NMR spectroscopy confirmed that the composition of the graft copolymers corresponded well to the monomer feed. For gel electrolytes prepared from the amphiphilic copolymers, the nature of the ionophobic parts of the amphiphilic graft copolymers had a great influence on the ion conductivity. Gel electrolytes based on graft copolymers containing fluorocarbon side chains showed significantly higher ion conductivity than electrolytes based on graft copolymers containing hydrocarbon groups. The ambient‐temperature ion conductivity was about 2.6 mS/cm at 20 °C for a gel electrolyte based on an amphiphilic graft copolymer consisting of an acrylate backbone carrying PEO and fluorocarbon side chains. Corresponding gels based on graft copolymers with PEO side chains and hydrocarbon groups showed an ambient‐temperature ion conductivity of about 1.2 mS/cm. The gel electrolytes contained 30 wt % copolymer and 70 wt % 1 M LiPF₆ in an ethylene carbonate/γ‐butyrolactone (2/1 w/w) mixture. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2223–2232, 2001     

Synthesis and electrooptical properties of triphenylamine- and oxadiazole-containing polymers

Soluble aromatic polyimides and copolyimides are synthesized on the basis of 4,4′-diaminotriphenylamine and oxadiazole-containing diamines. Poly(ester oxadiazoles) are prepared from acid dichlorides or oxadiazole-containing acid dihydrazides. The optical, electrochemical, and thermal properties of the polymers are investigated. It is shown that oxadiazole-containing polyimides and poly(ester oxadiazoles) are able to transfer electrons, while triphenylamine-containing polyimides and copolyimides can transfer holes and electrons.     

Synthesis of starlike PtBA‐g‐PEO amphiphilic graft copolymer via highly efficient Cu‐catalyzed SET‐NRC reaction at ambient temperature

Two new amphiphilic star graft copolymers bearing hydrophobic poly(tert‐butyl acrylate) backbone and hydrophilic poly(ethylene oxide) (PEO) side chains with different molecular weights were synthesized by sequential reversible addition fragmentation chain transfer (RAFT) polymerization and single electron transfer‐nitroxide radical coupling (SET‐NRC) reaction under mild conditions. RAFT homopolymerization of tert‐butyl 2‐((2‐bromopropanoyloxy)methyl)acrylate was mediated by a four‐armed chain transfer agent in a controlled way to afford a well‐defined starlike backbone with a narrow molecular weight distribution (M_w/M_n = 1.26). The target poly(tert‐butyl acrylate)‐g‐PEO (PtBA‐g‐PEO) star graft copolymers were synthesized by SET‐NRC reaction between Br‐containing PtBA‐based starlike backbone and PEO end functionalized with 2,2,6,6‐tetramethylpiperidine‐1‐oxyl (TEMPO) group using copper/N,N,N′,N′,N″‐pentamethyldiethylenetriamine as catalytic system at ambient temperature via grafting‐onto strategy. The critical micelle concentration values of the obtained amphiphilic star graft copolymers in aqueous media and brine were determined by fluorescence probe technique using pyrene as probe. Diverse micellar morphologies were formed by varying the content of hydrophilic PEO segment as well as the initial concentration of stock solution. In addition, poly(acrylic acid)‐g‐PEO double hydrophilic star graft copolymers were obtained by selective acidic hydrolysis of hydrophobic PtBA starlike backbone without affecting PEO side chains. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis of a water‐soluble diblock copolymer of polysulfonic diphenyl aniline and poly(ethylene oxide)

We report the synthesis of a water‐soluble diblock copolymer composed of polysulfonic diphenyl aniline (PSDA) and poly(ethylene oxide) (PEO), which was prepared by reacting an amine‐terminated PSDA and tosylate PEO (PEO‐Tos). First, a HCl‐mediated polymerization of sulfonic diphenyl aniline monomer with the formation of HCl‐doped PSDA was carried out. After its neutralization and reduction, a secondary amine‐functionalized PSDA was obtained. Second, PEO‐Tos was synthesized via the tosylation of the monohydroxyl PEO methyl ether with tosylol chloride. Diblock copolymers with various PEO segment lengths (PSDA‐b‐PEO‐350 and PSDA‐b‐PEO‐2000) were obtained with PEO‐350 [number‐average molecular weight (M_n) = 350] and PEO‐2000 (M_n = 2000). The prepolymers and diblock copolymers were characterized by Fourier transform infrared spectroscopy, NMR, mass spectrometry, and ultraviolet–visible light. They had relatively low conductivities, ranging from 10^?6 to 10^?3 S/cm, because of the withdrawing effect of the sulfonic group as well as the steric effects of the bulky aromatic substitutuents at the N sites of the polyaniline backbone and of the PEO block. These polymers were self‐doped, and an intermolecular self‐doping was suggested. The external doping was, however, more effective. The self‐doping induced aggregation in water among the PSDA backbones, which was also stimulated by the presence of hydrophilic PEO blocks. Furthermore, the electrical conductivities of the diblock copolymers were strongly temperature‐dependent. PSDA‐b‐PEO‐2000 exhibited about one order of magnitude increase in conductivity upon heating from 32 to 57 °C. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2179–2191, 2004     

Amphiphilic graft copolymers - preparation and interfacial properties

Amphiphilic graft copolymers containing poly(ethylene oxide) (PEO) grafts have been prepared by various methods, for example, by coupling of reactive hydrophobic backbone polymers with end-functionalised PEO, by macromonomer copolymerisation, and by anionic graft polymerisation of EO onto polymer backbones carrying functional groups as initiator precursors. The graft copolymers are amphiphilic and were shown to accumulate at surfaces and interfaces in solution and in the solid state. Amphiphilic starch derivatives were prepared by reaction of amylose and starch with aliphatic α-epoxides.     

Synthesis of polyimides and segmented block copolyimides by transimidization

The transimidization reaction has been successfully utilized to prepare a series of segmented block copolyimides. The synthesis and polymerization of an AX‐type amino imide monomer containing the tetrahydro[5]helicene unit were accomplished. The AX‐type amino imide monomer is stable during isolation and purification, owing to its inert X (e.g., N‐pyridyl) group, but yet readily underwent a self‐transimidization reaction and produced polyimide. Because of the presence of two reactive ends, such an AX‐type polyimide could be incorporated into a series of block copolyimides by reaction with commercially available dianhydrides and diamines. All the copolymers showed two distinct glass‐transition temperatures, typically around 250 and 430 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3991–3996, 2000     

Preparation and properties of alkylated poly(styrene-graft-ethylene oxide)

Poly(styrene-graft-ethylene oxide), having alkyl chains (C₁₂ or C₁₈) on the polystyrene main chain or on the poly(ethylene oxide) (PEO) side chains, were synthesized. The main chain was alkylated by first ionizing amide groups in a styrene/acrylamide copolymer with tert-butoxide, and then using the amide anions as sites for reactions with 1-bromoalkanes. An excess of amide anions was used in the reaction, and the remaining anions were subsequently utilized as initiator sites for the anionic polymerization of ethylene oxide (EO). Synthesis of poly(styrene-graft-ethylene oxide) with alkylated side chains was accomplished by polymerization of EO onto the ionized styrene/acrylamide copolymer, followed by an alkylation of the terminal alkoxide anions with 1-bromoalkanes. The alkylated graft copolymers were structurally characterized by using elemental analysis, ¹H NMR, GPC, and IR spectroscopy. DSC analysis showed that only graft copolymers with PEO contents exceeding about 50 wt % and side chain crystallinities comparable to those of homo-PEO. Main chain alkylated graft copolymers generally had higher crystalinities, as compared to nonalkylated and side chain alkylated samples. The graft copolymers absorbed water corresponding to one water molecule per EO unit at low PEO contents. The water absorption increased progressively at PEO contents above 30 wt % for main chain alkylated samples and above 50 wt % for non-alkylated samples. © 1995 John Wiley & Sons, Inc.     

Controlled synthesis and interface properties of new amphiphilic PCL-g-PEO copolymers

Novel biodegradable and biocompatible poly(epsilon-caprolactone)-graft-poly(ethylene oxide), PCL-g-PEO, copolymers consisting of biocompatible blocks have been synthesized by ring-opening copolymerization of epsilon-caprolactone (epsilon CL) and a poly(ethylene oxide) (PEO) macromonomer, i.e., PEO end-capped by an epsilon-caprolactone unit (gamma PEO.CL). The control is effective on the composition and length of both the hydrophobic polyester backbone and the hydrophilic PEO grafts. The reactivity ratios have been determined by monitoring the copolymer composition in relation to the comonomer conversion. The PCL-g-PEO copolymers have a tapered (gradient) rather than a random structure consistent with r(epsilon)CL = 3.95 and r(gamma)PEO.CL = 0.05. The amphiphilic graft copolymers display surfactant properties similar to those of PEO-b-PCL diblock copolymers of comparable composition and solubility, as supported by CHCl3/water interfacial tension measured by the pendant drop method.     

Unprecedented diverse nanostructures formed by amphiphilic graft copolymer bearing PEO side chains synthesized by ATNRC

A series of well‐defined amphiphilic graft copolymers bearing hydrophilic poly(ethylene oxide) (PEO) side chains with tunable grafting densities were synthesized by atom transfer nitroxide radical coupling (ATNRC) reaction using CuBr/PMDETA as catalytic system via the grafting‐onto strategy. PEO side chains were linked to α‐C of carbonyl of polyacrylate‐based backbone, not to the ester side groups as usual, so that every repeating unit of the backbone possessed a pendant steric bulky tert‐butyl group. The critical micelle concentrations of the obtained amphiphilic graft copolymers in aqueous media determined by fluorescence probe technique using pyrene as probe increased with the raising of molecular weights. These amphiphilic graft copolymers with novel chemical structure showed unprecedented diverse nanostructures visualized by transmission electron microscopy in aqueous media and micellar morphologies varied with the changing of experiment parameters. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis, Purification and Characterization of Amphiphilic and Microphase Separated Graft Copolymer Polystyrene-g-Poly(ethylene oxide)

The present paper covers the poly (ethylene oxide) macromer with vinyl benzyl terminal group (PEO-VB) prepared by deactivation of the alkoxide function of mono-functional "living" PEO chains with vinyl benzyl chloride (VBC). The obtained macromers were subjected to careful purification and detailed characterization. A new kind of amphiphilic polystyrene-g-poly(ethylene oxide) (PS-g-PEO) with both mi-crophase separated and PEO side chains was synthesized from radical copolymerization of PEO-VB macromer with styrene monomer. An improved purification method, referred as "selective dissolvation", was established for the isolation of graft copolymers from the grafting products, and the purity and yield of the purified copolymers were satisfactory. The well-defined structure of the purified copolymers was confirmed by IR, 1H NMR and GPC. The bulk composition of the graft copolymers was determined by a well-established first derivative UV spectrometry. Various experimental parameters controlling the copolymeri     

Superstructure in segmented polyether–urethanes

The morphology of several series of segmented polyether–urethanes was studied. The “hard” segments contained urethane and urea linkages formed by 4,4′-dicyclohexylmethane diisocyanate (Hylene W) and selected aliphatic and aromatic monomeric diamines (DA). The “soft” segments were composed of oligomeric poly(ethylene oxide) (PEO), poly(propylene oxide) (PPO), or both PEO and PPO. For studying the composition–morphology relationships, the molecular weight and relative content of PEO, and the relative content of PPO were varied systematically. Different diamines were used as chain extenders. The methods of wide-angle x-ray diffraction (WAXD), small-angle x-ray scattering (SAXS), polarizing microscopy, scanning electron microscopy (SEM), and differential scanning calorimetry (DSC) were employed in the investigation. The effects of PEO content on domain formation were very significant. Calculations based on a highly simplified model indicated that, for two adjacent molecules, if two hard segments are associated with each other, the probability for the association of the next two hard segments varies inversely with the third power of soft segment length. Copolymers composed of both POE and PPO displayed enhanced domain and anisotropic superstructure. The phenomenon was interpreted in terms of polymer incompatibility. The effects on morphology of different DA's as chain extenders were tentatively accounted for by the symmetry, hydrogen bonding, and rigidity of the hard segments as well as their incompatibility with the soft segments. The formation and deformation of superstructure were of particular interest. A model was proposed to account for the formation of the resultant anisotropic structure and mechanical properties.     

Structure–property relationships of low dielectric constant,nanoporous, thermally stable polyimides via grafting of poly(propylene glycol) oligomers

Synthesis of high temperature polyimide foams with pore sizes in the nanometer range was developed. Foams were prepared by casting graft copolymers comprising a thermally stable block as the matrix and a thermally labile material as the dispersed phase. The copolyimides as the matrix material were prepared via polycondensation reactions of pyromellitic dianhydride with three new diamines (4BAP, 3BAP, and BAN) through the poly(amic acid) precursors. Functionalized poly(propylene glycol) (PPGBr‐1000 and PPGBr‐2500) as the labile oligomer was prepared via reaction of poly(propylene glycol) monobutyl ether with 2‐bromoacetyl bromide. Graft copolymers were prepared by the reaction of the poly(amic acid)s with these thermally labile constituents. Upon thermal treatment the labile blocks were subsequently removed leaving pores with the size and shape of the original copolymer morphology. The polyimides and foamed polyimides were characterized by some conventional methods including FTIR, H‐NMR, DSC, TGA, SEM, TEM, and dielectric constant. The average pore size of the polyimide nanofoams was in the range of 5–20 nm. The structure–property relationships of the prepared nanofoams were investigated based on the diamine structures and also molecular weights of labile groups. Copyright © 2008 John Wiley & Sons, Ltd.     

Synthesis and characterization of SPUU–PEO–heparin graft copolymers

A new synthetic approach for the preparation of segmented polyurethaneurea (SPUU)–PEO–Heparin graft copolymers (B–PEO–Hep) has been developed. The procedure involved the coupling of hexamethylene diisocyanate (HMDI) to soluble Biomer® (B) through an allophanate/biuret reaction. The free isocyanate (NCO) groups attached to Biomer® were then coupled to PEO terminal hydroxyl groups to form PEO grafted Biomer® (B–PEO). B–PEO free hydroxy groups were modified with HMDI to introduce terminal isocyanate groups. The NCO functionalized B–PEO was then coupled to heparin (Hep) functional groups (? OH, ? NH₂) producing B–PEO–Hep graft copolymer. Synthetic intermediates were confirmed by FTIR, NCO group determination, and toluidine blue heparin assay. Physical characterization techniques, such as contact angle measurements, water swelling, light scattering measurements, and DSC thermal analysis, detailed properties of the graft copolymer containing covalently bound heparin. This new heparinized copolymer can be applied as a coating on other existing blood contacting surfaces without changing bulk properties. The heparin bioactivity observed attests to the usefulness of this new procedure as a coating to improve the blood compatibility of blood-contacting surfaces.     

Synthesis and properties of segmented block copolymers based on mixtures of poly(ethylene oxide) and poly(tetramethylene oxide) segments

The synthesis and characterisation of segmented block copolymers based on mixtures of hydrophilic poly(ethylene oxide) and hydrophobic poly(tetramethylene oxide) polyether segments and monodisperse crystallisable bisester tetra-amide segments are reported. The PEO length was varied from 600 to 8000 g/mol and the PTMO length was varied from 650 to 2900 g/mol. The influence of the polyether phase composition on the thermal mechanical and the elastic properties of the resulting copolymers was studied.The use of high melting monodisperse tetra-amide segments resulted in a fast and almost complete crystallisation of the rigid segment. The copolymers had only one polyether glass transition temperature, which suggests that the amorphous polyether segments were homogenously mixed. Thermal analysis of the copolymers showed one polyether melting temperature that was lower than in the case of ideal co-crystallisation between the two polyether segments. However, at PEO or PTMO lengths larger than 2000 g/mol two polyether melting temperatures were observed. The copolymer with the best low temperature properties was based on a mixture of PEO and PTMO segments, both having a molecular weight of 1000 g/mol, at a weight ratio of 30/70.     

High-Temperature transformations of aromatic diamines in the Rolivsan matrix

The formation mechanism, structure, and properties of new network copolymers prepared by thermochemical transformations of Rolivsans with aromatic diamines were studied by IR, ¹Н NMR, and ¹³С NMR spectroscopy and by dynamic mechanical, thermal, and elemental analysis.     

ATNRC and SET‐NRC synthesis of PtBA‐g‐PEO well‐defined amphiphilic graft copolymers

A series of new well‐defined amphiphilic graft copolymers containing hydrophobic poly(tert‐butyl acrylate) backbone and hydrophilic poly(ethylene oxide) side chains were reported. Reversible addition‐fragmentation chain transfer homopolymerization of tert‐butyl 2‐((2‐bromopropanoyloxy)methyl)acrylate was first performed to afford a well‐defined backbone with a narrow molecular weight distribution (M_w/M_n = 1.07). The target poly(tert‐butyl acrylate)‐g‐poly(ethylene oxide) (PtBA‐g‐PEO) graft copolymers with low polydispersities (M_w/M_n = 1.18–1.26) were then synthesized by atom transfer nitroxide radical coupling or single electron transfer‐nitroxide radical coupling reaction using CuBr(Cu)/PMDETA as catalytic system. Fluorescence probe technique was employed to determine the critical micelle concentrations (cmc) of the obtained amphiphilic graft copolymers in aqueous media. Furthermore, PAA‐g‐PEO graft copolymers were obtained by selective acidic hydrolysis of hydrophobic PtBA backbone while PEO side chains kept inert. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012