Magnetically activated micromixers for separation membranes

Presented here is a radically novel approach to reduce concentration polarization and, potentially, also fouling by colloids present in aqueous feeds: magnetically responsive micromixing membranes. Hydrophilic polymer chains, poly(2-hydroxyethyl methacrylate) (PHEMA), were grafted via controlled surface-initiated atom transfer radical polymerization (SI-ATRP) on the surface of polyamide composite nanofiltration (NF) membranes and then end-capped with superparamagnetic iron oxide magnetite (Fe(3)O(4)) nanoparticles. The results of all functionalization steps, that is, bromide ATRP initiator immobilization, SI-ATRP, conversion of PHEMA end groups from bromide to amine, and carboxyl-functional Fe(3)O(4) nanoparticle immobilization via peptide coupling, have been confirmed by X-ray photoelectron spectroscopy (XPS) and field emission scanning electron microscopy (FESEM). These nanoparticles experience a magnetic force as well as a torque under an oscillating external magnetic field. It has been shown, using particle image velocimetry (PIV), that the resulting movement of the polymer brushes at certain magnetic field frequencies induces mixing directly above the membrane surface. Furthermore, it was demonstrated that with such membranes the NF performance could significantly be improved (increase of flux and salt rejection) by an oscillating magnetic field, which can be explained by a reduced concentration polarization in the boundary layer. However, the proof-of-concept presented here for the active alteration of macroscopic flow via surface-anchored micromixers based on polymer-nanoparticle conjugates has much broader implications.     

UV辐照接枝制备酚酞基聚芳醚酮纳滤膜——链转移剂的作用

酚酞基聚芳醚酮(PEK-C)超滤膜的表面通过紫外辐照接枝丙烯酸(AA)可以制备对II价盐有很好截留率的亲水性纳滤膜. FTIR-ATR、表面接触角、SEM和AFM的研究结果表明, 在接枝单体溶液中加入异丙醇(i-PrOH)作为链转移剂并不影响AA在PEK-C超滤膜表面的接枝反应. 得到的改性膜同样具有优良的纳滤性能. 与不加i-PrOH的AA改性膜相比, 新合成的膜有较高的滤出液通量, 该膜对盐离子的截留率虽有所降低, 但可以通过增加接枝反应时间和辐照光源的强度来提高. i-PrOH的浓度对膜的分离性能的影响很大, 在低浓度时, 改性膜对离子的截留率会有所下降, 继续提高i-PrOH的浓度, 膜的截留率不再变化而滤出液通量会有成倍的增加, 表明链转移剂的存在可能会提高膜的接枝密度, 增加膜的表面电荷, 使膜对离子的截留率保持不变.     

铅(Ⅱ)离子印迹复合膜的制备及其性能研究

以聚丙烯微孔膜(MPPM)为支撑,采用共价表面修饰和离子印迹技术,制备了Pb(Ⅱ)离子印迹复合膜.首先通过紫外光引发丙烯酸接枝聚合,在MPPM表面引入羧基;然后基于羧基和氨基的反应,将壳聚糖共价接枝到MPPM表面;再以Pb(Ⅱ)为模板离子、环氧氯丙烷为交联剂,通过配位键作用形成离子印迹位点.制备过程通过ATR-FTIR和XPS分析得到了证实.利用扫描电子显微镜(SEM)-能量色散X射线光谱仪(EDX)对膜表面及截面的形貌及元素分布进行了分析.静态水接触角和纯水通量实验结果显示,印迹复合膜具有良好的表面亲水性和渗透性,在离子印迹聚合物接枝率为174.4μg/cm2时,水通量高达2659±58 L/(m2.h).印迹复合膜对Pb(Ⅱ)离子的吸附亲和性和渗透选择性分别通过平衡结合实验和竞争渗透实验进行评价.与非印迹复合膜相比,印迹复合膜对Pb(Ⅱ)离子展现出更强的吸附亲和性,更快的吸附速率及更好的渗透选择性,以Cu(Ⅱ)和Zn(Ⅱ)作为竞争离子,其渗透选择性因子分别为3.43和3.93.     

Preparation of polymer hollow microspheres covered by polymer solid particles via two polymerization steps

A novel surface modification method for titania nanoparticles is provided via the surface‐initiated photocatalytic polymerization with the aid of acrylic acid (AA) or sodium styrene sulfonate (NaSS). The properties of modified titania nanoparticles are investigated with aqueous electrophoresis measurements, dynamic light scattering (DLS), and transmission electron microscopy (TEM). Then the modified titania is used as Pickering stabilizer for further polymerization and the morphology of the resulted polymer microspheres is characterized by TEM and field‐emission scanning electron microscopy. It is proven that the addition of AA or NaSS for the surface‐initiated polymerization can obviously affect the structure and morphology of the final polymer composite microspheres. The formation mechanism of several kinds of polymer particles is also proposed. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

二步法聚丙烯/丙烯酸表面接枝聚合研究

研究了二步法聚丙烯膜表面的丙烯酸接枝反应 .实验发现 ,以醋酐为溶剂的反应体系所得接枝率明显好于以水为溶剂的体系 ;接枝率随光敏剂浓度、单体浓度增大而增加 ;提高反应温度 ,可使接枝率明显增大 ;接枝后的聚丙烯膜表面亲水性可明显改善 .并用红外光谱证实了丙烯酸在聚丙烯膜表面的接枝 .     

Fabrication of shape-controllable polyaniline micro/nanostructures on organic polymer surfaces: obtaining spherical particles, wires, and ribbons

A novel strategy was developed in order to prepare various micro/nanostructured polyanilines (PANI) on polymer substrates. The strategy involved two main steps, i.e., a grafting polymerization of acrylate acid (AA) onto the surface of a polypropylene (PP) film and subsequently an oxidative polymerization of aniline on the grafted surface. By tuning the conformation of the surface-grafted poly acrylate acid (PAA) brushes, as well as the ratio of AA to aniline, the shape of the PANIs fixated onto the surfaces of the polymer substrate could be controlled to go from spherical particles to nanowires and eventually to nanoribbons. In these structures, the PAA brushes not only acted as templates but also as dopants of PANI, and thereby, the nanostructured PANIs could be strongly bonded with the substrate. In addition, the surface of the PP films grafted with polyaniline nanowires and nanoribbons displayed superhydrophobicity with contact angles for water of approxiamtely 145 and 151 degrees , respectively.     

Grafting of regenerated cellulose membrane by surface‐initiated atom transfer radical polymerization and its pH‐resposive behavior

Regenerated cellulose (RC) membranes which have pH modulated permeability have been prepared by anchoring the hydroxyl groups on the membrane surface with 2‐bromoisobutyryl bromide, followed by grafting with acrylic acid (AA) using atom transfer radical polymerization (ATRP). The obtained membranes were analyzed by X‐ray photoelectron spectroscopy (XPS), Fourier transform infrared attenuated total reflection spectrometer (ATR‐FTIR), scanning electron microscopy (SEM), TGA and the results showed that AA had been grafted onto the membrane surfaces successfully. Then the pH modulated permeability properties were tested by water flux measurement. All results show that the pH modulated permeability properties of a RC membrane can be obtained by surface‐initiated ATRP. Copyright © 2010 John Wiley & Sons, Ltd.     

Excellent anti‐bacterial activity and surface properties of polyamide‐6 films modified with argon‐plasma and methyl diallyl ammonium salt‐graft

In this study, the effect of argon‐plasma treatment on the grafting of methyl diallyl ammonium salt (MDAA) onto polyamide‐6 film and the anti‐bacterial and surface properties of the plasma‐ and graft‐treated film were investigated. The grafting amounts of MDAA caused by argon‐plasma treatment increased with the increase in the plasma exposure time and plasma power. The analyses of Fourier transform infrared (FT‐IR) spectroscopy and electron spectroscopy for chemical analysis (ESCA) spectra revealed that the epoxy and vinyl groups of MDAA could be grafted on the argon‐plasma treated polyamide‐6 film. The survey spectra of ESCA, the patterns of atomic force microscopy (AFM), and the spectra from scanning electron microscopy (SEM) were employed to certify the surface modification of argon‐plasma treated and the argon‐plasma treated/MDAA grafted polyamide‐6 films. Argon‐plasma treatment could generate the functional group and increase the roughness on the surface of polyamide‐6 film. This phenomenon could enhance the grafting effect of MDAA. The anti‐bacterial property of argon‐plasma treated/MDAA grafted polyamide‐6 film was excellent. This argon‐plasma treated/MDAA grafted polyamide‐6 film was expected to be applied on the field of packing. Copyright © 2008 John Wiley & Sons, Ltd.     

SEM研究PET核孔膜的光接枝聚合

以PET核孔膜为基材 ,二苯甲酮为引发剂 ,采用光接枝方法实现了丙烯酸和丙烯酰胺在核孔膜上的接枝 ,用扫描电镜 (SEM)直接观察了接枝前后膜的表面形貌 ,考察了不同因素对于接枝位置和接枝效果的影响 .发现膜材料本身特性和接枝反应条件对接枝位置和接枝效果有较大影响 .通过光接枝能够实现膜孔的封盖、缩小、填堵等不同的效果 .采用正侧涂布法反应 ,标准直孔 ,特别是小孔径膜 (0 4 μm) ,不利于孔内的接枝 ,接枝主要在膜的表面 ,从而产生孔封盖效应 .双锥形的非标准直孔 ,由于孔壁的受光性好 ,容易发生孔壁上的接枝从而被填充 .大孔径的膜 (5 μm) ,需要加入交联剂才能在孔壁上形成厚的接枝层 .提出了一种新的反应方法 背侧吸附法 ,反应液依靠毛细作用由膜的底部吸入膜孔 ,膜的向光侧表面不存在反应液 ,接枝只发生在膜孔内 ,从而得到很好的填孔效果 .     

Polymeric membranes: Surface modification for minimizing (bio)colloidal fouling

This paper presents an overview on recent developments in surface modification of polymer membranes for reduction of their fouling with biocolloids and organic colloids in pressure driven membrane processes. First, colloidal interactions such as London–van der Waals, electrical, hydration, hydrophobic, steric forces and membrane surface properties such as hydrophilicity, charge and surface roughness, which affect membrane fouling, have been discussed and the main goals of the membrane surface modification for fouling reduction have been outlined. Thereafter the recent studies on reduction of (bio)colloidal of polymer membranes using ultraviolet/redox initiated surface grafting, physical coating/adsorption of a protective layer on the membrane surface, chemical reactions or surface modification of polymer membranes with nanoparticles as well as using of advanced atomic force microscopy to characterize (bio)colloidal fouling have been critically summarized.     

SURFACE MODIFICATION OF MICROPOROUS POLYPROPYLENE MEMBRANES BY GRAFT POLYMERIZATION OF N,N-DIMETHYLAMINOETHYL METHACRYLATE

Surface modification of microporous polypropylene hollow fiber membranes was performed by radical-induced graft polymerization of N,N-dimethylaminoethyl methacrylate (DMAEMA). The influences of temperature, monomer concentration and pre-adsorbed amount of benzoyl peroxide on grafting degree were studied respectively. It was found that the appropriate graft temperature was 75℃, at which the grafting degree was the highest and the hydrolytic decomposition of DMAEMA the lowest. Scanning electron photomicrography and the average pore diameters of the modified membranes demonstrated that part of the micropores on the membrane surface was plugged by the grafted polyDMAEMA chains, especially at high grafting degree. Contact angle and water swelling experiments showed that a moderate grafting degree could improve the hydrophilicity of the membranes. In the range of I 1.3%o-12.0% grafting degree, the water swelling percentage reached its maximum (51.1%) and the contact angle reached its minimum (74 degrees). The bovine serum albumin (BSA) adsorption experiment indicated that the grafted polyDMAEMA had a dual effect on protein adsorption. At the first stage, the BSA adsorption decreased with increasing of DMAEMA grafting degree. As the interaction between BSA and polyDMAEMA on membrane surface increased, the BSA adsorption increased with increasing of DMAEMA grafting degree.     

接枝改性碳酸钙及其在聚合物中的应用研究

介绍了近年来碳酸钙表面接枝改性的研究进展,讨论了自由基接枝聚合、辐照接枝聚合和力化学表面接枝聚合及偶联剂预处理与辐照并用接枝聚合改性方法。其中重点讨论了最新研究的偶联剂预处理与辐照并用接枝改性纳米碳酸钙的方法。用此方法制备的聚合物/纳米碳酸钙纳米复合材料在其他力学性能基本不变的情况下,大幅度提高了其缺口冲击强度和断裂伸长率。指出了碳酸钙表面接枝改性应向着提高接枝单体量和采用弹性体单体方面发展。     

Photoinduced graft polymerization of 2-methacryloyloxyethyl phosphorylcholine on polyethylene membrane surface for obtaining blood cell adhesion resistance

Phospholipid polymer, poly[2-methacryloyloxyethyl phosphorylcholine (MPC)], was grafted with polyethylene (PE) membrane using photoinduced polymerization technique to make the membrane resistant to cell adhesion. The water contact angle on the PE membrane grafted with poly(MPC) decreased with an increase in the photopolymerization time. This decrease corresponded to the increase in the amount of poly(MPC) grafted on the PE surface. The same graft polymerization procedure was applied using other hydrophilic monomers, such as acrylamide (AAm), N-vinylpyrrolidone (VPy) and methacryloyl poly(ethylene glycol) (MPEG). These monomers were also polymerized to form grafted chains on the PE membrane, and the grafting was confirmed with X-ray photoelectron spectroscopy. Analysis of amount and distribution of plasma proteins at the plasma-contacting surface of the original and the modified PE membranes were analyzed using immunogold assay. The grafting of poly(MPC) and poly(VPy) on PE membrane reduced the plasma protein adsorption significantly compared with that on the original PE membrane. However, the PE membranes grafted with poly(AAm) or poly(MPEG) did not show any effects on protein adsorption. Platelet adhesion on the original and modified PE membranes from platelet-rich plasma was also examined. A large number of platelets adhered and activated on the original PE membrane. Grafting with poly(AAm) did not suppress platelet adhesion, but grafting with poly(MPC) or poly(VPy) on the PE membrane was effective in preventing platelet adhesion. It is concluded that the introduction of the phosphorylcholine group on the surface could decrease the cell adhesion to substrate polymer.     

Preparation of an ion-imprinted fiber for the selective removal of Cu2+

A novel Cu(2+)-imprinted fiber (IIF) was prepared by grafting acrylic acid (AA) onto the surface of a polypropylene (PP) fiber and subsequently modified with polyethylenimine (PEI). An examination by infrared spectroscopy and scanning electron microscopy confirmed that the ion-imprinted polymer was successfully introduced onto the surface of a PP fiber. The modification of PP fibers with AA was beneficial to the grafting of PEI onto the fibers. The highest grafting degree of PEI could reach 120 wt % under optimal grafting conditions. This IIF showed excellent tensile and chemical stability in acid solution, which qualified the IIF for practical applications. Besides having a high adsorption capacity for Cu(2+) (120 mg/g), the IIF adsorbent showed a high selectivity for Cu(2+) as compared with that of the non-ion-imprinted fiber (NIF). The dynamic adsorption results indicated that IIF can thoroughly remove Cu(2+) from the solution in a relatively short contact time. The effective treatment volume was about 910 bed volumes. The selectivity coefficient of IIF for Cu(2+) with respect to Zn(2+) could reach 76.4. IIF also has good regeneration performance and could maintain almost the same adsorption capacity for copper ions after 10 adsorption-desorption cycles.     

Grafting of molecularly imprinted polymer to porous polyethylene filtration membranes by plasma polymerization

An application of plasma-induced grafting of polyethylene membranes with a thin layer of molecularly imprinted polymer (MIP) was presented. High-density polyethylene (HDPE) membranes, “Vyon,” were used as a substrate for plasma grafting modification. The herbicide atrazine, one of the most popular targets of the molecular imprinting, was chosen as a template. The parameters of the plasma treatment were optimized in order to achieve a good balance between polymerization and ablation processes. Modified HDPE membranes were characterized, and the presence of the grafted polymeric layer was confirmed based on the observed weight gain, pore size measurements, and infrared spectrometry. Since there was no significant change in the porosity of the modified membranes, it was assumed that only a thin layer of the polymer was introduced on the surface. The experiments on the re-binding of the template atrazine to the membranes modified with MIP and blank polymers were performed. HDPE membranes which were grafted with polymer using continuous plasma polymerization demonstrated the best result which was expressed in an imprinted factor equal to 3, suggesting that molecular imprinting was successfully achieved.

Characterization of multilayer nanofiltration membranes using positron annihilation spectroscopy

Positron annihilation spectroscopy (PAS) coupled with a slow positron beam was used to characterize in situ the layer structure and depth profile of the cavity size in thin film composite (TFC) polyamide nanofiltration (NF) membranes prepared by the interfacial polymerization method. Two techniques, using PAS coupled with a slow positron beam of Doppler broadening energy spectra (DBES) and positron annihilation lifetime spectroscopy (PALS) designed to reveal the layer structure and the cavity sizes contained in a multilayer thin film composite NF membrane, were assessed. To the best knowledge of the authors, a characterization of the depth profile of cavities in NF membranes using PAS coupled with a slow positron beam has never been reported. The membranes selected have a composite structure containing three layers: a selective polyamide layer, a transition layer, and a porous support prepared by the phase inversion technique. Furthermore, the cavity size distribution in the selective top layer plays an important role in determining the performance of the NF membranes.     

Effect of hydration of polyamide membranes on the surface electrokinetic parameters: surface characterization by x-ray photoelectronic spectroscopy and atomic force microscopy

The surface and the solid/liquid interface of two polyamide membranes, one experimental (B0) and one commercial (NF45), have been characterized by X-ray photoelectronic spectroscopy (XPS), atomic force microscopy (AFM), and zeta potential, respectively. The surface roughness, determined by AFM data analysis, is different for the two membranes, and results show that the commercial NF45 membrane presents a much lower roughness than the experimental B0 membrane. XPS data indicate that the surface of membrane NF45 is similar to that of pure polyamide, while membrane B0 contains a considerable amount of impurities. The homogeneity in depth of both membranes was also studied by determining the composition profile at different analysis angles. Streaming potential along the membrane surface or tangential streaming potential (TSP) measurements with NaCl solutions at different concentrations were carried out with both membranes to determine the zeta potential and the electrokinetic surface charge density, and a correlation between membrane surface and interface parameters is made. Some differences in atomic concentrations of membrane surface elements and X-ray photoelectronic spectra of the samples used in TSP measurements and after a drying process at 90 degrees C for 24 h can be observed when they are compared with those for fresh membranes. Electrokinetic parameters for membrane NF45 (TSP, zeta potential, and surface electrokinetic charge density) obtained from three different series of measurements strongly decrease as a result of membrane use, but for membrane B0 they are practically independent of the number of measurements. This difference in the electrokinetic behavior of the two membranes has been related to the hydration process of the surface for each sample studied by XPS and AFM.     

亲水膜的表面改性及在膜蒸馏中的应用

膜的微孔性和疏水性是水溶液膜蒸馏的两个基本条件,迄今人们均采用疏水性高分子材料制成疏水微孔膜用于膜蒸馏研究。本文采用辐照接枝聚合和等离子体表面聚合的方法,将亲水的醋酸纤维素微孔膜和硝酸纤维素微孔膜表面疏水化改性,成功地用于膜蒸馏研究,大大扩展了疏水微孔膜的材料来源。实验结果表明,亲水膜表面改性得到的疏水膜,其膜蒸馏性能不低于疏水材料制成的膜,尤其是等离子体聚合法可以实现多种特殊单体在多孔的材料表面聚合,成为制备高性能疏水微孔膜的有效手段,为膜蒸馏的深入发展和实用化创造了有利条件。     

Enhanced separation performance of PVDF/PVP-g-MMT nanocomposite ultrafiltration membrane based on the NVP-grafted polymerization modification of montmorillonite (MMT)

A novel hydrophilic nanocomposite additive (PVP-g-MMT), coupling of hydrophilic modifier, self-dispersant, and pore-forming agent (porogen), was synthesized by the surface modification of montmorillonite (MMT) with N-vinylpyrrolidone (NVP) via "grafting from" polymerization in the presence of H(2)O(2)-NH(3)·H(2)O as the initiator, and then the nanocomposite membrane of poly(vinylidene fluoride) (PVDF) and PVP-g-MMT was fabricated by wet phase inversion onto clean glass plates. The existence and dispersion of PVP-g-MMT had a great role on structures, morphologies, surface composition, and chemistry of the as-prepared nanocomposite membranes confirmed by varieties of spectroscopic and microscopic characterization techniques, all of which were the correlated functions of PVP-g-MMT content in casting solution. By using the dead-end filtration of protein aqueous solution, the performance of the membrane was evaluated. It was seen that all of the nanocomposite membranes showed obvious improvement of water flux and proper BSA rejection ratio, compared to the control PVDF membrane. Meanwhile, dynamic BSA fouling resistance and flux recovery properties were also greatly enhanced due to the changes of surface hydrophilicity and morphologies. All the experimental results indicated that the as-prepared PVDF nanocomposite membranes showed better separation performances than the control PVDF membrane. Hopefully, the demonstrated method of hydrophilic nanocomposite additive synthesis would be applied for commonly hydroxyl group-containing inorganic nanoparticles, which was favorable to fabricate hydrophilic nanoparticle-enhanced polymer membranes for water treatment.     

一种利用梯度光掩模制备梯度表面的简便方法

以自制杂化双向拉伸聚丙烯/氧化硅(BOPP/SiOx)有机/无机杂化膜为基材,由喷墨打印机直接在杂化膜表面打印色阶图案,制备出对紫外光强度呈梯度透过的梯度光掩模;通过此掩模控制,在双向拉伸聚丙烯(BOPP)和聚对苯二甲酸乙二醇酯(PET)表面实施受限光催化氧化(CPO)光感应羟基化反应、受限光接枝丙烯酸(AA)以及表面...