Magnetic and magnetotransport properties in Co5Cu95 melt-spun alloys

Giant magnetoresistance (GMR) has been observed in Co₅Cu₉₅ alloys fabricated by melt-spinning. The highest MR change of 28.0% occurs for Co₅Cu₉₅ after annealing at 450°C for 30 min. Based on the super-paramagnetic assumption, the average size of Co particles embedded in Cu matrix, ranging from 3.0 to 6.0 nm, has been determined by simulating the magnetization curves at 295 K which is higher than the blocking temperatures for the samples. Comparison with phenomenological theory for GMR indicates that the interfacial spin-dependent scattering is the dominant scattering mechanism underlying GMR origin in granular systems. Additionally, for the samples in as-quenched state or annealed at temperatureT _A=350°C, the electron hybridization and super-paramagnetic behaviors of fine Co particles may be responsible for the low value of MR change.     

Effects of layering and working pressure on magnetic and magnetotransport properties of as sputtered multilayered granular Co/Cu films

Heterogeneous films of CoCu having high giant magnetoresistance (MR) were prepared in the form of multilayered granular specimens by a two-target RF sputtering. MR performances of 11% at 293 K were obtained in as deposited granular films. The magnetic and magnetotransport properties could be changed to a large extent, by varying the thickness of the deposited Co (Cu) layer as well as the Ar pressure. The effect of Co concentration, in the range 5–30%, and the influence of thermal treatments were also analysed.     

Magnetic properties of the amorphous alloy Fe80Er20

Amorphous Fe₈₀Er₂₀ alloys were prepared with the melt spinning technique. The ribbons were investigated by Mössbauer spectroscopy from room temperature to 4.2 K. A phase transition from the paramagnetic to the ferromagnetic phase could be observed. The temperature dependence of the internal magnetic field was measured. The correlations of the hyperfine parameters were determined from the 4.2 K spectrum.     

退火诱导亚稳态Fe80Cu20合金固溶体的结构相变

利用扩展x射线吸收精细结构和x射线衍射研究了机械合金化制备的体心立方(bcc)的亚稳态Fe80Cu20合金固溶体的结构随退火温度的变化特点.结果表明,在300-873 K温度范围内,随着退火温度的升高,bcc结构物相的晶格常数近于线性降低,这主要是由于Cu原子从bcc结构Fe80Cu20合金固溶体中逐渐偏析出来,生成面心立方(fcc)结构的Cu物相所致.经603 K退火后,Cu原子的平均键长RCu-Cu增加了0.003 nm左右,大约有50%的Cu原子从bcc结构的Fe80Cu20合金固溶体中偏析出来.在773 K退火后,bcc结构Fe80Cu20合金固溶体近于完全相分离,生成了bcc结构的α-Fe与fcc结构的Cu物相.     

Magnetooptical,optical, and magnetotransport properties of Co/Cu superlattices with ultrathin cobalt layers

We investigated the field dependences of the magnetization and magnetoresistance of superlattices [Co(t _x, Å)/Cu(9.6 Å)]30 prepared by magnetron sputtering, differing in the thickness of cobalt layers (0.3 Å ≤ t _Co ≤ 15 Å). The optical and magnetooptical properties of these objects were studied by ellipsometry in the spectral region of hω= 0.09–6.2 eV and with the help of the transverse Kerr effect (hω= 0.5–6.2 eV). In the curves of an off-diagonal component of the tensor of the optical conductivity of superlattices with t _Co = 3–15 Å, a structure of oscillatory type (“loop”) was detected in the ultraviolet region, resulting from the exchange splitting of the 3d band in the energy spectrum of the face-centered cubic structure of cobalt (fcc Co). Based on magnetic experiments and measurements of the transverse Kerr effect, we found the presence of a superparamagnetic phase in Co/Cu superlattices with a thickness of the cobalt layers of 3 and 2 Å. The transition from superlattices with solid ferromagnetic layers to superparamagnetic cluster-layered nanostructures and further to the structures based on Co and Cu (t _Co = 0.3–1 Å) with a Kondo-like characteristics of the electrical resistivity at low temperatures is analyzed.     

Effects of oxidation and cluster distribution on thermal and magnetotransport properties of mechanically alloyed Co–Cu powders

Thermal and magnetotransport properties of mechanically alloyed Co₃₀Cu₇₀ powders of three different milling times are studied. Both milling and annealing bring about oxidation of the samples. The powders show exothermic behaviors corresponding to the lattice-recovery process. Different milling times and annealing temperatures give rise to different exothermic peaks because of oxidation and the cluster distribution. At room temperature, the compressed powders show, on average, up to 11% giant magnetoresistance (GMR) under 10 kOe with sharp switching. The results may be understood in terms of spin-dependent scattering across Co/oxide/Cu interfaces. Annealing reduces the resistance but does not promote the GMR. By annealing at 400 °C, the GMR is entirely suppressed as the magnetic content is largely replaced by oxides. PACS 72.15.Eb; 75.47.De; 75.47.Np     

Magnetic domain structures and magnetotransport properties in Co-Ag granular thin films

The magnetic microstructures and magnetotransport properties in granular Co_xAg_1-x films with 17%≤x≤62% were studied. Magnetic force microscopy (MFM) observations showed the presence of magnetic stripe domains in as-deposited samples with x≥45% and the evolution of the magnetic domain patterns to in-plane domains with annealing. A perpendicular magnetic anisotropy as high as about 8×10⁵ ergs/cc for as-deposited Co₆₂Ag₃₈ and about 6×10⁵ ergs/cc for as-deposited Co₄₅Ag₅₅ was observed by magnetization and torque measurements. With increasing annealing temperature, the perpendicular magnetic anisotropy became negative. The origin of the perpendicular magnetic anisotropy may be attributed to a rhombohedral distortion of the cubic cell due to residual substrate-film stresses. The magnetic stripe domains are the consequence of the interplay of the indirect or direct exchange, perpendicular magnetic anisotropy and dipolar interactions. Finally, magnetoresistance (MR) curves displayed training behaviours and different shapes when measured with different configurations (parallel, transverse and perpendicular). It is proposed that the existence and the evolution of the magnetic domain structures strongly affect the magnetotransport properties due to the extra contribution of the electron scattering at the domain walls. Furthermore, an anisotropic MR also contributes to the overall MR curves. Received: 2 March 2000 / Accepted: 28 March 2000 / Published online: 23 May 2001     

多层膜［Co85Cr15/Pt］20的磁性、垂直磁记录特性和微结构的关系

采用磁控溅射法制备了性能优良的以Pt为缓冲层的［Co85₈₅Cr15_{15/Pt］2020 多层膜，研究了溅射气压对［Co8585Cr1515/Pt］2020多层膜微结构和磁性的 影响.研究结果表明，Ar溅射气压对［Co8585Cr1515/Pt］2020多层膜的微结构 、垂直磁各向异性和矫顽力有重要的影响 关键词： 溅射气压 多层膜 垂直磁各向异性 有效磁各向异性常数}     

Effect of Cu additions on the magnetic properties and microstructure of FeCoNbB nanocrystalline alloy

The influence of Cu content and the annealing conditions in the (Fe_0.5Co_0.5)_85?x Nb₇B₈Cu _x (x=0.5, 1.0, 1.5) soft magnetic alloys on the magnetic properties and microstructure were investigated. The additions of Cu lower the primary and secondary crystallization temperatures and the α→γ phase transformation temperature of the FeCoNbB alloys. The (Fe_0.5Co_0.5)₈₄Nb₇B₈Cu₁ alloy annealed at 873 K for 3.6 ks, in which α-(Fe, Co) nanocrystalline phase with diameter of 5 nm precipitated from the amorphous matrix, shows the best soft magnetic properties. The resulting (Fe_0.5Co_0.5)₈₄Nb₇B₈Cu₁ nanocrystalline alloy exhibits a high saturation flux density of 1.88 T, low coercivity of 42 A/m, very high Curie temperature of 1240 K, as well as low core loss of 770 W/kg at 10 kHz under maximum magnetization of 1 T.     

Magnetic properties of lithographically defined lateral Co/Ni80Fe20 wires

A novel micro-fabrication technique has been used to create an array of lateral magnetic multilayers consisting of micron-sized sputtered Co and Ni₈₀Fe₂₀ wires. The structures were fabricated using conventional optical lithography and a combination of hard and soft lift-off methods. For the field applied parallel to the wires intrinsic easy axis, we observed two switching fields corresponding to the distinct coercive field of the Ni₈₀Fe₂₀ wires (H_c1) and Co wires (H_c2) constituting the lateral multilayer wire array. A state of anti-parallel relative alignment of magnetization was observed when the applied field is greater than the switching field of Ni₈₀Fe₂₀ wires but less than the switching field of Co wires. We found the region of anti-parallel alignment of magnetization between the Co and Ni₈₀Fe₂₀ wires to be very sensitive to the relative orientation of the applied magnetic field.     

Correlation between the viscoelastic properties of a soft crystal and its microstructure

We investigate the rheological properties of a cubic fcc phase of micelles obtained by aggregation of a triblock copolymer (PEO)₁₂₇(PPO)₄₈(PEO)₁₂₇ in water as selective solvent. The resulting soft solid is submitted to a range of stresses varying from 20 to 800Pa in Couette geometry. Creep and flow behaviour can be distinguished and interpreted in terms of structural changes previously observed by SAXS under flow. Contrasting with other systems, no discontinuity in the flow behaviour is associated with the structural changes. The strong shear thinning is interpreted from the scattering data, as resulting from the nucleation of a new structure of hexagonal compact planes parallel to the Couette walls. This creates a lubricating domain in the gap, whose size grows with the applied shear rate. We argue moreover that the very existence of flow (as a steady state opposed to creep) is associated with this so-called layer-sliding structure in a fraction, however small, of the sample. Received on 4 June 1999 and Received in final form 6 September 1999     

Point Defects and Their Properties in the Fe20Ni20Cr20Co20Cu20 High-Entropy Alloy

JETP Letters - The characteristics of interstitial atoms and vacancies in the Fe20Ni20Cr20Co20Cu20 high-entropy alloy have been determined by the molecular dynamics and statics methods. The effect...     

Au80Sn20合金焊料制备工艺

针对高功率二极管激光器的封装要求,通过磁控溅射的方法制备了Au80Sn20合金焊料,使用扫描电子显微镜（SEM）观察其微结构和表面形貌;利用能谱仪（EDX）和X射线荧光测试仪分析其成分;采用差热分析法（DTA）测试其熔化温度,并用制备的Au80Sn20合金焊料进行了可焊性实验。结果表明:磁控溅射法可以制备Au80Sn20合金焊料,其制备的Au80Sn20合金焊料表面无明显缺陷,结构致密;成分与理论值接近;熔点与理论熔点接近;焊接浸润性好,空洞率小,强度大。     

Au80Sn20合金焊料制备工艺

针对高功率二极管激光器的封装要求,通过磁控溅射的方法制备了Au80Sn20合金焊料,使用扫描电子显微镜（SEM）观察其微结构和表面形貌;利用能谱仪（EDX）和X射线荧光测试仪分析其成分;采用差热分析法（DTA）测试其熔化温度,并用制备的Au80Sn20合金焊料进行了可焊性实验。结果表明：磁控溅射法可以制备Au80Sn20合金焊料,其制备的Au80Sn20合金焊料表面无明显缺陷,结构致密;成分与理论值接近;熔点与理论熔点接近;焊接浸润性好,空洞率小,强度大。     

Magnetic properties and microstructure of melt-spun Sm(Co,Fe,Cu,Zr)8 magnets

We report on the microstructural and magnetic properties of rapidly quenched Sm(Co_balFe_0.1Cu_xZr_0.04)₈ ribbons. Samples spun at velocities above 40 m/s are nanocrystalline and magnetically hard, even in the as-spun state. The coercivity and its temperature coefficient can be improved by annealing at 750°C. Samples spun at low speeds have low coercivity in the as-spun state and are characterized by larger grain sizes. By annealing a cellular precipitation structure within the grains, similar to that of bulk Sm(Co,Fe,Cu,Zr)_z magnets, can be obtained in Cu-containing samples, resulting in an increase of the coercivity, since the precipitates act as pinning centers. Some precipitation occurs even in as-spun Cu-free samples, indicating that their formation is not directly related to the existence of Cu, in contrast to the cellular structure. Compared to the bulk materials, lower annealing temperatures and shorter heat treatment times are required and the slow cooling process is not needed. The activation volumes for the magnetic reversal process are estimated by magnetic relaxation measurements.     

Elastic Dipoles in Crystal and Glassy Aluminum and High-Entropy Fe20Ni20Cr20Co20Cu20 Alloy

JETP Letters - Molecular dynamics simulation has shown that anisotropic local atomic configurations, which are in essence elastic dipoles, exist in noncrystalline structures of Al and FeNiCrCoCu....