Pentacene precursors for solution-processed OFETs

15-Acetoxy- and 15-hydroxy-6,13-dihydro-6,13-ethanopentacenes sublimed over 300 °C and no pentacene was formed below the temperature. The precursors bearing chlorinated epithiomethano bridges suffered complicated decomposition to give oligomeric pentacene derivatives. The precursor bearing an epithio-oxomethano bridge underwent smooth and clean conversion to pentacene by heat or light. An organic field-effect transistor fabricated by the spin-coating method of the precursor followed by light irradiation at 120 °C showed a good FET performance of μ=2.5×10⁻² cm² V⁻¹ s⁻¹ and on/off ratio=3.8×10⁴.     

Oxidation of benzyl alcohols with difluoro(aryl)-λ-bromane: formation of benzyl fluoromethyl ethers via oxidative rearrangement

Oxidative rearrangement of benzyl alcohols with difluoro(p-trifluoromethylphenyl)-λ³-bromane (5 × 10⁻² M) in chloroform at room temperature afforded aryl fluoromethyl ethers selectively in good yields, probably via 1,2-shift of aryl groups from benzylic carbon to oxygen atoms.     

Comparison of soluble manganese(IV) and acidic potassium permanganate chemiluminescence detection using flow injection and sequential injection analysis for the determination of ascorbic acid in Vitamin C tablets

The limits of detection (3s) for ascorbic acid were 5×10⁻⁸ M with acidic potassium permanganate using both flow injection analysis (FIA) and sequential injection analysis (SIA) whereas the soluble manganese(IV) afforded 1×10⁻⁸ M and 5×10⁻⁹ M for FIA and SIA, respectively. Determinations of ascorbic acid in Vitamin C tablets were achieved with minimal sample pretreatment using a standard additions calibration and gave good agreement with those of iodimetric titration.     

A highly sensitive amperometric sensor for oxygen based on iron(II) tetrasulfonated phthalocyanine and iron(III) tetra-(N-methyl-pyridyl)-porphyrin multilayers

The development of a highly sensitive sensor for oxygen is proposed using a glassy carbon (GC) electrode modified with alternated layers of iron(II) tetrasulfonated phthalocyanine (FeTsPc) and iron(III) tetra-(N-methyl-pyridyl)-porphyrin (FeT4MPyP). The modified electrode showed excellent catalytic activity for the oxygen reduction. The reduction potential of the oxygen was shifted about 330 mV toward less negative values with this modified electrode, presenting a peak current much higher than those observed on a bare GC electrode. Cyclic voltammetry and rotating disk electrode (RDE) experiments indicated that the oxygen reduction reaction involves 4 electrons with a heterogenous rate constant (k_obs) of 3 × 10⁵ mol⁻¹ L s⁻¹. A linear response range from 0.2 up to 6.4 mg L⁻¹, with a sensitivity of 4.12 μA L mg⁻¹ (or 20.65 μA cm⁻² L mg⁻¹) and a detection limit of 0.06 mg L⁻¹ were obtained with this sensor. The repeatability of the proposed sensor, evaluated in terms of relative standard deviation (R.S.D.) was 2.0% for 10 measurements of a solution of 6.4 mg L⁻¹ oxygen. The sensor was applied to determine oxygen in pond and tap water samples showing to be a promising tool for this purpose.     

Dissolved oxygen amperometric sensor based on layer-by-layer assembly using host-guest supramolecular interactions

The development of a simple, efficient and sensitive sensor for dissolved oxygen is proposed using the host-guest binding of a supramolecular complex at a host surface by combining a self-assembled monolayer (SAM) of mono-(6-deoxy-6-mercapto)-β-cyclodextrin (βCDSH), iron (III) tetra-(N-methyl-4-pyridyl)-porphyrin (FeTMPyP) and cyclodextrin-functionalized gold nanoparticles (CDAuNP). The supramolecular modified electrode showed excellent catalytic activity for oxygen reduction. The reduction potential of oxygen was shifted about 200 mV toward less negative values with this modified electrode, presenting a peak current much higher than those observed on a bare gold electrode. Cyclic voltammetry and rotating disk electrode (RDE) experiments indicated that the oxygen reduction reaction involves probably 4-electrons with a rate constant (k_obs) of 7 × 10⁴ mol⁻¹ L s⁻¹. A linear response range from 0.2 up to 6.5 mg L⁻¹, with a sensitivity of 5.5 μA L mg⁻¹ (or 77.5 μA cm⁻² L mg⁻¹) and a detection limit of 0.02 mg L⁻¹ was obtained with this sensor. The repeatability of the proposed sensor, evaluated in terms of relative standard deviation was 3.0% for 10 measurements of a solution of 6.5 mg L⁻¹ oxygen.     

Ab initio investigation of O3 addition to double bonds of limonene

The reaction of the O₃ addition to double bonds of the limonene in the gas phase has been investigated using ab initio methods. Four different possibilities for the O₃ addition to the double bonds, which correspond to the two C–C double bonds (endocyclic or exocyclic), and two different orientations of each C–C double bonds, have been considered. The corresponding rate constants have been calculated using the transition-state theory (TST) at the CCSD(T)/6-31G(d) + CF//B3LYP/6-311+G(d,p) level of theory. The high-pressure limit of the overall rate constant at 298 K is found to be ∼2.92 × 10⁻¹⁶ cm³ molecule⁻¹ s⁻¹ that is in a good agreement with the experimental data, and the rate constants of the four individual reaction channels turn out to be 2.1 × 10⁻¹⁶ cm³ molecule⁻¹ s⁻¹, 1.2 × 10⁻¹⁷ cm³ molecule⁻¹ s⁻¹, 6.5 × 10⁻¹⁷ cm³ molecule⁻¹ s⁻¹ and 5.1 × 10⁻¹⁸ cm³ molecule⁻¹ s⁻¹ for 1-endo, 2-endo, 1-exo and 2-exo, respectively.     

Oxidation of substituted pyridines by dimethyldioxirane: kinetics and solvent effects

The oxidation of a series of substituted pyridines by dimethyldioxirane (1) produced the expected N-oxides in quantitative yields. The second order rate constants (k₂) for the oxidation of a series of substituted pyridines (2a-g) by dimethyldioxirane were determined in dried acetone at 23 °C. An excellent correlation with Hammett sigma values was found (ρ = −2.91, r = 0.995). Kinetic studies for the oxidation of 4-trifluoromethylpyridine by 1 were carried out in the following dried solvent systems: acetone (k₂ = 0.017 M⁻¹ s⁻¹), carbon tetrachloride/acetone (7:3; k₂ = 0.014 M⁻¹ s⁻¹), acetonitrile/acetone (7:3; k₂ = 0.047 M⁻¹ s⁻¹), and methanol/acetone (7:3; k₂ = 0.68 M⁻¹ s⁻¹). Kinetic studies of the oxidation of pyridine by 1 versus mole fraction of water in acetone [k₂ = 0.78 M⁻¹ s⁻¹ (χ = 0) to k₂ = 11.1 M⁻¹ s⁻¹ (χ = 0.52)] were carried out. The results showed the reaction to be very sensitive to protic, polar solvents.     

Simultaneous determination of uric acid,xanthine, hypoxanthine and caffeine in human blood serum and urine samples using electrochemically reduced graphene oxide modified electrode

This paper describes the fabrication of graphene on glassy carbon electrode (GCE) by electrochemical reduction of graphene oxide (GO) attached through 1,6-hexadiamine on GCE and the simultaneous determination of structurally similar four purine derivatives using the resultant electrochemically reduced GO (ERGO) modified electrode. The electrocatalytic activity of ERGO was investigated toward the oxidation of four important purine derivatives, uric acid (UA), xanthine (XN), hypoxanthine (HXN) and caffeine (CAF) at physiological pH. The modified electrode not only enhanced the oxidation currents of the four purine derivatives but also shifted their oxidation potentials toward less positive potentials in contrast to bare GCE. Further, it successfully separates the voltammetric signals of the four purine derivatives in a mixture and hence used for the simultaneous determination of them. Selective determination of one purine derivative in the presence of low concentrations other three purine derivatives was also realized at the present modified electrode. Using differential pulse voltammetry, detection limits of 8.8 × 10⁻⁸ M, 1.1 × 10⁻⁷ M, 3.2 × 10⁻⁷ M and 4.3 × 10⁻⁷ M were obtained for UA, XN, HXN and CAF, respectively. The practical application of the modified electrode was demonstrated by simultaneously determining the concentrations of UA, XN, HXN and CAF in human blood plasma and urine samples.     

Electrosorption of Os(III)-complex at single-wall carbon nanotubes immobilized on a glassy carbon electrode: application to nanomolar detection of bromate, periodate and iodate

A simple procedure was developed to prepare a glassy carbon electrode modified with single-wall carbon nanotubes (SWCNTs) and Os(III)-complex. The glassy carbon (GC) electrode modified with CNTs was immersed into Os(III)-complex solution (direct deposition) for a short period of time (60 s). 1,4,8,12-Tetraazacyclotetradecane osmium(III) chloride, (Os(III)LCl₂)·ClO₄, irreversibly and strongly adsorbed on SWCNTs immobilized on the surface of GC electrode. Cyclic voltammograms of the Os(III)-complex-incorporated-SWCNTs indicate a pair of well defined and nearly reversible redox couple with surface confined characteristic at wide pH range (1-8). The surface coverage (Γ) and charge transfer rate constant (k_s) of the immobilized Os-complex on SWCNTs were 3.07 × 10⁻⁹ mol cm⁻², 5.5 (±0.2) s⁻¹, 2.94 × 10⁻⁹ mol cm⁻², 7.3 (±0.3) s⁻¹ at buffer solution with pH 2 and 7, respectively, indicate high loading ability of SWCNTs for Os(III) complex and great facilitation of the electron transfer between electroactive redox center and carbon nanotubes immobilized on the electrode surface. Modified electrodes showed higher electrocatalytic activity toward reduction of BrO₃⁻, IO₃⁻ and IO₄⁻ in acidic solutions. The catalytic rate constants for catalytic reduction bromate, periodate and iodate were 3.79 (±0.2) × 10³, 7.32 (±0.2) × 10³ and 1.75 (±0.2) × 10³ M⁻¹ s ⁻¹, respectively. The hydrodynamic amperometry of rotating modified electrode at constant potential (0.3 V) was used for nanomolar detection of selected analytes. Excellent electrochemical reversibility of the redox couple, good reproducibility, high stability, low detection limit, long life time, fast amperometric response time, wide linear concentration range, technical simplicity and possibility of rapid preparation are great advantage of this sensor.     

Electrocatalytic reduction of nitrite at polypyrrole nanowire-platinum nanocluster modified glassy carbon electrode

Pt nanoclusters were deposited in polypyrrole (PPy) nanowires by cyclic voltammetry method, fabricating a PPy-Pt nanocomposite on glassy carbon electrode (PPy-Pt/GCE). The electrocatalytic reduction of nitrite at PPy-Pt/GCE has been investigated using 0.5 M H₂SO₄ solution. The sensor exhibited excellent electrocatalytic activity toward nitrite reduction. In acidic medium, the cyclic voltammetry at 20 mV s^− 1 gave a nitrite reduction peak at − 0.124 V with 0.566 μA μM^− 1 current sensitivity in the range of 5.0 × 10^− 7-1.0 × 10^− 3 M. The detection limit was 1.5 × 10^− 7 M (s/n = 3). The proposed method was successfully applied in the detection of nitrite in real water samples and obtained satisfactory results. The PPy-Pt composite modified electrode had good storage stability, reproducibility and anti-interference ability.     

Combined sorption/transport of sodium dodecyl sulfate and hydrochloric acid in a blend of cellulose acetate butyrate with cellulose acetate hydrogen phthalate

The transport of hydrochloric acid (0.001-0.1 M) and sodium dodecyl sulfate (0.001-0.1 M) has been measured through a membrane consisting of a blend of cellulose acetate butyrate and cellulose acetate hydrogen phthalate. The cellulose derivative blend is suggested to suffer an alteration in the degree of hydrophobicity when in equilibrium with sodium dodecyl sulfate (SDS) through hemimicelle formation. An increase in surface hydrophobicity of the blend when in equilibrium with SDS solution was observed by fluorescence measurements using the vibronic bands of the probe pyrene, as well as by water desorption kinetics; a decrease of the effective diffusion coefficients from 1.2 × 10⁻¹¹ m² s⁻¹ in the absence of SDS to approximately 2 × 10⁻¹³ m² s⁻¹ in its presence was found. The value obtained for the mutual diffusion coefficient of HCl in the concentration range 0.001-0.1 M (D=4.2×10⁻¹⁴ m² s⁻¹) shows also that the membrane presents hydrophobic features. The flux of SDS in the blend membrane at different pH values shows two distinct permeation rates depending on the cmc. However, from the calculation of permeability coefficients at SDS concentrations below the cmc a clear decrease in P is found, whilst, at concentrations above the cmc the permeability coefficients are nearly constant, only showing a slightly increase. The diffusion coefficients of SDS in the blend increase over the whole SDS concentration range analysed and show an effective diffusion coefficient 2-3 orders of magnitude below the diffusion coefficients of SDS in aqueous solutions. This fact suggests that the only diffusing species are SDS unimers. The presence of HCl in the SDS bulk solution has the effect of increasing the permeability and diffusion coefficients. Mutual analysis of permeation and diffusion coefficients and sorption isotherms shows that, on decreasing the pH, the interactions between SDS and the polymer network decrease. This is also reflected in a clear decrease of the hydrophobic interactions between the diffusing and polymeric species, provoked by a decrease in the unimer-unimer association.     

Systematic investigation on new SrCo1−yNbyO3−δ ceramic membranes with high oxygen semi-permeability

SrCo_1−yNb_yO_3−δ (y = 0.025–0.4) were synthesized for oxygen separation application. The crystal structure, phase stability, oxygen nonstoichiometry, electrical conductivity, and oxygen permeability of the oxides were systematically investigated. Cubic perovskite, with enhanced phase stability at higher Nb concentration, was obtained at y = 0.025–0.2. However, the further increase in niobium concentration led to the formation of impurity phase. The niobium doping concentration also had a significant effect on electrical conductivity and oxygen permeability of the membranes. SrCo_0.9Nb_0.1O_3−δ exhibited the highest electrical conductivity and oxygen permeability among the others. It reached a permeation flux of ∼2.80 × 10⁻⁶ mol cm⁻² s⁻¹ at 900 °C for a 1.0-mm membrane under an air/helium oxygen gradient. The further investigation demonstrated the oxygen permeation process was mainly rate-limited by the oxygen bulk diffusion process.     

Silver-ion redox sensing based on colloid formation by gallate ester derivatives

Plasmon absorption of silver colloid, which was formed by reduction of silver ion with compounds bearing gallate ester groups in ethanol, was observed by absorption spectroscopy. The time-dependent absorption of silver colloid was found, which shows that the silver colloid is unstable and easy to aggregate. It seemed that a calixarene derivative bearing two gallate ester groups was the most suitable for determining silver ion. In order to prevent the silver colloid aggregation, poly(N-vinylpyrrolidone) (PVP) was added into the solution at a constant time after the preparation of sample solutions. In the calibration graph, the absorbance increased with increasing silver ion concentration, especially in the concentration range of 2.00 × 10⁻⁶ to 1.00 × 10⁻⁵ M. It is possible to determine silver ion concentrations using this method.     

Flow injection system with in-line Winkler's procedure using 16-way valve and spectrofluorimetric determination of dissolved oxygen in environmental waters

Flow injection spectrofluorimetry with in-line Winklers procedure was developed for the dissolved oxygen (DO) determination. 2-Thionaphthol reacted with iodine produced by Winkler’s method to form fluorescence inactive disulfide compound. To automate the process completely, a 5-channel flow system with a newly designed 16-way valve was assembled. The system consisted of a dispersion coil (DC), a precipitate formation coil (PFC), a precipitate dissolving coil (PDC), and extraction coil (EC). A calibration can be constructed by using a standard iodine solution for dissolved oxygen. The calibration graph was linear over the range 1.2×10⁻⁴∼6.0×10⁻⁴ mol l⁻¹ iodine (1.96∼9.80 mg O l⁻¹)). The relative standard deviation (n=6) was below 0.3% for the 4×10⁻⁴ mol l⁻¹ iodine (6.27 mg O l⁻¹) determination. The sample throughput was 12/h.     

Effluent treatment using electrochemically bleached seawater-oxidative degradation of pollutants

Use of seawater electrolytically enriched with hypochlorite and the in situ generation of hypochlorite on the high seas, stand a good chance for disinfection and decrease of bio and non-biodegradable organics in effluent before discharged into estuaries and deep oceans. Enriched seawater effectively decreased the biological oxygen demand measured over 5 days (BOD) and chemical oxygen demand (COD) levels of semi-treated wastewater. The oxidative degradation of Brilliant Blue, a triaryl industrial dye by hypochlorite and electrolytically enriched seawater are compared at pH 6.5. Both had similar magnitude second-order rate constants (21±1 M⁻¹ s⁻¹) and procedure is feasible. Increase in acid concentration enhanced the reaction rate. With 1:1 and 1:100 molar ratios of dye to hypochlorite, the COD=140 mg L⁻¹ of 1.0×10⁻³ M dye reduced to 100 and 30 mg L⁻¹ respectively.     

Electrochemical behaviors of guanosine on carbon ionic liquid electrode and its determination

The electrochemical behaviors of guanosine on the ionic liquid of N-butylpyridinium hexafluorophosphate (BPPF₆) modified carbon paste electrode (CPE) was studied in this paper and further used for guanosine detection. Guanosine showed an adsorption irreversible oxidation process on the carbon ionic liquid electrode (CILE) with the oxidation peak potential located at 1.12 V (vs. SCE) in a pH 4.5 Britton-Robinson (B-R) buffer solution. Compared with that on the traditional carbon paste electrode, small shift of the oxidation peak potentials appeared but with a great increment of the oxidation peak current on the CILE, which was due to the presence of ionic liquid in the modified electrode adsorbed the guanosine on the surface and promoted the electrochemical response. The electrochemical parameters such as the electron transfer coefficient (α), the electron transfer number (n), and the electrode reaction standard rate constant (k_s) were calculated as 0.74, 1.9 and 1.26 × 10⁻⁴ s⁻¹, respectively. Under the optimal conditions the oxidation peak current showed a good linear relationship with the guanosine concentration in the range from 1.0 × 10⁻⁶ to 1.0 × 10⁻⁴ mol/L by cyclic voltammetry with the detection limit of 2.61 × 10⁻⁷ mol/L (3σ). The common coexisting substances showed no interferences to the guanosine oxidation. The CILE showed good ability to distinguish the electrochemical response of guanosine and guanine in the mixture solution. The urine samples were further detected by the proposed method with satisfactory results.     

Foreign gas broadening and shift of the strongly “forbidden” lead line at 1278.9 nm

The collisional broadening and shift rate coefficients of the “forbidden“ 6p^{2 3}P₀ → 6p^{2 3}P₁ transition in lead were determined by diode laser absorption measurements performed simultaneously in two resistively heated hot-pipes. One hot-pipe contained Pb vapor and noble gas (Ar or He) at low pressure, while the other was filled with Pb and noble gas at variable pressure. The measurements were performed at temperatures of 1220 K and 1290 K, i.e., lead number densities of 4.8 × 10¹⁵ cm^− 3 and 1.2 × 10¹⁶ cm^− 3. The broadening rates were obtained by fitting the experimental collisionally broadened absorption line shapes to theoretical Voigt profiles. The shift rates were determined by measuring the difference between the peak absorption positions in the spectra measured simultaneously in the heat pipe filled with noble gas at reference pressure and the one with noble gas at variable pressure. The following data for the broadening and shift rate coefficients due to collisions with Ar and He were obtained: γ_B^Ar = (3.4 ± 0.1) × 10^− 10 cm³ s^− 1, γ_B^He = (3.8 ± 0.1) × 10^− 10 cm³ s^− 1, γ_S^Ar = (− 7.3 ± 0.8) × 10^− 11 cm³ s^− 1, γ_S^He = (− 6.5 ± 0.7) × 10^− 11 cm³ s^− 1.     

Synthesis of a new type of dibenzopyrromethene-boron complex with near-infrared absorption property

A new type of π-extended 4-bora-3a,4a-diaza-s-indacene (BODIPY dye), bis(isoindole)-derived benzo[1,3,2]oxazaborinine 1, has been synthesized by seven-step procedure from 2-methoxybenzoic acid methyl ester. The benzannulation of the pyrrole ring and the formation of a structurally strained intramolecular B-O ring enable the dye to absorb near-infrared light at ca. 750 nm with a molecular extinction coefficient (ε) of ca 8.3 × 10⁴ M⁻¹ cm⁻¹ in THF. The absorption properties are discussed on the basis of DFT calculations. Interestingly, a film of 5,5-dihexyloxy derivative 1b, which was fabricated by a spin-coating procedure on a glass plate, exhibited a dramatic bathochromic shift of absorbance as compared to the solution, with λ_max of 922 nm.     

Determination of bismuth and zinc in pharmaceuticals by first derivative UV-Visible spectrophotometry

A first order derivative spectrophotometric method has been developed for the simultaneous determination of bismuth and zinc by dithizone without time-consuming extraction step. The reactions of bismuth and zinc with dithizone in a three component solution prepared in water, acetone and n-propanol mixture have been investigated. These cations react with dithizone in this mixture at pH 5.0, forming coloured complex that is stable for at least 2 h. The linear range in D evaluation was between 3.0 × 10⁻⁶ and 1.8 × 10⁻⁵ mol l⁻¹ for Zn and 2.4 × 10⁻⁶ and 1.2 × 10⁻⁵ mol l⁻¹ for Bi. The limits of detection for the analytical procedure were found 0.05 mg l⁻¹ for both cations. The relative standard deviations for the determination of 0.5 mg l⁻¹ bismuth and 0.5 mg l⁻¹ zinc were 1.2 and 1.1%, respectively, for five determinations. The procedure is simple, rapid and reliable. This method was applied to the determination of bismuth and zinc in the pharmaceutical materials successfully. Good agreement was achieved between the results obtained by the proposed and comparative methods.     

Sequential injection system for simultaneous determination of chloride and iodide by a Gran’s plot method

This paper describes an automated set-up based on the sequential injection analysis (SIA) concept with potentiometric detection for the determination of chloride and iodide at low concentrations. The assessment of both ion concentrations is accomplished by titration with silver ions using the Gran’s plot approach. The proposed procedure enables chloride and iodide to be determined simultaneously in the range 6.0×10⁻⁶ to 1.0×10⁻⁴ mol l⁻¹ if a minimum silver concentration in the volumetric solution is chosen (5×10⁻⁵ mol l⁻¹). Conventional titrations based on the first derivative evaluation of the equivalence points applied to the same solutions fail, especially for chloride determinations. Although, a comparison of results obtained for higher analyte concentrations shows that they have similar accuracy and precision.