甲醇水蒸气重整制氢Pd/ZnO催化剂还原过程中Pd与ZnO的相互作用

 采用程序升温还原、程序升温脱附、程序升温电导及X射线衍射研究了并流共沉淀法制备的15.9%Pd/ZnO催化剂还原过程中结构和物种的变化及电荷的传递,考察了还原温度对该催化剂催化甲醇水蒸气重整制氢的影响. 结果表明,还原过程中Pd与ZnO间存在明显的相互作用,导致氢溢流,溢流氢促进了ZnO还原并使ZnO与Pd形成活性中心PdZn合金. 催化剂的还原历程为 PdO/ZnO → Pd/ZnO → PdZnO1-x/ZnO → 无定形PdZn合金/ZnO → 晶型PdZn合金/ZnO. 并流共沉淀法制备的Pd/ZnO催化剂Pd分散度高, PdZn合金形成温度低. 在523～573 K还原后,催化剂的PdZn合金粒径为5～14 nm, 此时催化剂对甲醇的转化率及二氧化碳选择性均达到最大值.     

甲醇水蒸气重整制氢Pd/ZnO催化剂的研究

采用并流共沉淀法制备Pd／ZnO甲醇水蒸气重整制氢催化剂,考察了Pd的质量分数和还原温度对催化剂性能的影响。结果表明,当Pd质量分数为15．9％,还原温度为573K时,催化剂有较好的甲醇转化率及二氧化碳选择性。TPR结果表明,PdO在室温下被还原为金属Pd,在440K开始有部分ZnO被还原。XRD分析结果表明,PdZn合金是甲醇水蒸气重整反应的活性中心;在21．9％Pd／ZnO催化剂上出现了Pd2Zn合金相,导致催化剂的活性下降;反应过程中还原催化剂形成PdZn合金,其活性不如相同条件下纯氢还原的。15．9％Pd／ZnO催化剂及工业铜基催化剂的初始稳定性结果显示,在8h内,15．9％Pd／ZnO催化剂上甲醇转化率保持在66％以上,而铜基催化剂的活性下降了14．4％。     

Pd/SAPO-34催化剂上CO低温氧化反应

 采用水热法合成了小晶粒的 SAPO-34, MnSAPO-34 和 CuSAPO-34 分子筛, 并以它们为载体采用浸渍法制备了一系列不同 Pd 含量的催化剂用于催化 CO 氧化反应. 结果表明: 分子筛载体、催化剂制备条件、反应条件、Pd 含量及预还原等对催化剂的活性影响较大. 催化剂活性随焙烧温度的增加而降低, 而随着反应温度的升高而提高, 担载在 SAPO-34 上 Pd 含量为 1.35% 时性能最佳. X射线衍射和透射电镜结果表明 Pd 物种高度分散于催化剂上, 粒子粒径在 2~8 nm; X射线光电子能谱及氢气程序升温还原结果表明, 高度分散的 Pd2+ 物种是 CO 氧化反应活性位. 随着反应进行被还原为 Pd0 物种, 因而导致催化剂活性下降. H2 预还原处理催化剂致使活性下降的实验结果也支持了这一结论.     

负载型Au-Pd双金属催化剂的制备及其对CO氧化的催化活性

采用改性的等体积浸渍法制备了SiO2负载的Au-Pd双金属催化剂,考察了催化剂的焙烧温度对CO氧化反应活性的影响.与623,723和773K的条件下焙烧的催化剂相比,673K焙烧的催化剂具有良好的催化CO氧化活性,CO完全转化温度低于398K.应用N2物理吸附、X射线衍射、程序升温还原、CO程序升温脱附及X射线光电子能谱等技术对催化剂进行了表征.结果表明,673K焙烧的催化剂具有最大的比表面积和最小的孔径,存在Au0,Pd0和PdO相,AuxPdy合金相很少;而773K焙烧的催化剂上除了含有Au0,Pd0和PdO相外,还存在明显的AuxPdy合金相.具有大比表面积,小孔径,Au0,Pd0和PdO多相共存的催化剂可使CO的吸附量增加,催化活性提高;而AuxPdy合金相的生成并不能提高催化剂的催化活性.     

Pd/ZnO在乙炔选择加氢反应中的不同催化机制研究(英文)

化学选择性是评价催化剂性能最重要的参数之一,它直接决定了产物的经济价值及后续的分离成本.传统的负载型金属催化剂由于其金属粒径分布不均,且不同原子数组成的粒子通常具有特征产物选择性,从而限制化学选择性的提高;另一方面,对于金属多原子活性中心,反应物在催化剂表面可以存在多种吸附构型进而衍化为不同产物,产物可控性差.因此,获得金属尺寸均一,且具有原子分散的活性中心,即单原子催化剂,成为官能团多相催化转化高选择性的迫切需求.本课题组通过400 oC还原1%-Pd/ZnO得到PdZn金属间化合物,依据其规律排布的Pd-Zn-Pd单元获得Pd基单原子催化剂.该催化剂在乙烯化工中少量乙炔的加氢转化反应中获得令人欣喜的催化性能——兼具有乙炔的高转化率和乙烯的高选择性.结合微量吸附量热、理论计算等表征,Pd活性中心在PdZn金属间化合物中的特殊空间排布是其优异催化性能的根源,即乙炔以较强的σ键吸附在两个相邻的单Pd金属中心,易吸附活化加氢生成乙烯,而乙烯则吸附于单Pd金属中心,较弱的π键形式吸附有利于其脱附避免过渡加氢.基于前期研究,构筑具有均一单金属中心的负载型单原子催化剂是获得高选择性的另一有效方法,且较之于PdZn金属间化合物催化剂,该类单原子催化剂兼具有原子利用率最大化的优点.本文采用等体积浸渍法制备Pd/ZnO催化剂,通过降低Pd金属含量(1 wt%→0.1 wt%→0.01 wt%)并在较低的温度下(100 oC)还原(H2-TPR表明高温还原形成PdZn金属间化合物型合金)得到负载型单原子催化剂(Pd1/ZnO SAC).高分辨电镜结果表明,当Pd负载量由1%降至0.1%,金属纳米颗粒的粒径尺寸显著降低,而在0.01%-Pd/ZnO催化剂表面,Pd活性中心则以单原子状态分散于载体ZnO表面.X-射线吸收光谱及电子能谱表明,随着负载量的降低,Pd活性物种具有更高的正电性.该催化剂在乙炔选择性加氢反应中表现出更加优越的催化性能,具有与PdZn催化剂相当的高选择性,而更优的比活性.这归结于Pd1/ZnO单原子催化剂的Pdδ+单原子活性中心有助于其与乙炔的静电相互作用并吸附活化加氢生成乙烯,并促使乙烯以较弱的π键吸附,从而易于从催化剂表面脱附获得高选择性.     

发烟硫酸中Pd／C催化甲烷选择氧化制甲醇

以PdCl2为前驱体,采用浸渍法制备了Pd/C催化剂,并在发烟硫酸中考察了其催化甲烷选择氧化反应的性能,采用X射线粉末衍射、X射线光电子能谱、高分辨透射电镜和CO吸附等方法对催化剂进行了表征. 甲烷选择氧化反应得到的主产物硫酸单甲酯经水解后得到甲醇,在5%Pd/C催化剂、Pd用量30 μmol、反应温度180 ℃、反应压力4.0 MPa、反应时间 4 h 和发烟硫酸中SO3含量为50%的优化工艺条件下,甲烷转化率为23.6%, 甲醇的选择性和收率分别为69.5%和16.4%, 在一定程度上可实现催化剂的多次重复使用. Pd/C催化剂上的甲烷选择氧化反应可能遵循亲电取代机理,催化性能与Pd负载量、Pd粒子尺寸和分散度等有关.     

利用ZnO@ZIF-8核壳结构构建高选择性、高稳定性的Pd/ZnO催化剂用于CO_2加氢制甲醇（英文）

近年来由于环境问题CO_2加氢制甲醇催化反应重新回归为研究热点。对于Pd/ZnO催化剂,研究表明PdZn合金相是制甲醇反应的活性中心,而单独Pd利于CO生成。为了实现Pd和ZnO的充分接触,本工作以一种ZnO@ZIF-8核壳型结构为载体负载Pd纳米颗粒后经由高温煅烧制得PZZ8-T催化剂(T为不同煅烧温度),同时制备了ZnO纳米棒负载Pd的PZ催化剂作为对比。在随后的CO_2加氢反应中,相比于PZ,PZZ8-T展现出极高的甲醇选择性。之后我们通过一系列表征探究了催化剂的构效关系,发现催化剂的甲醇选择性与表面Pd的化学态有关,更多的Pd以PdZn合金的形式存在将会带来更高的甲醇选择性。XPS O 1s谱图和EPR分析表明CO_2的活化与催化剂表面的氧空穴和ZnO极性面含量直接相关。而化学吸附手段进一步对Pd-ZnO界面进行了表征,揭示了其与CO_2转化速率的关联。本工作的意义在于,一是展现了利用新材料制备更优的传统催化剂的方法,二是通过表面分析手段加深了对催化剂构效关系的理解。     

氧化锌纳米线外延生长PdZn纳米粒子的制备及在甲醇水蒸气重整反应中的催化性能

以采用改进的气相沉积法制备的具有规整{1010}晶面的氧化锌纳米线为载体,合成了氧化锌纳米线负载钯催化剂,考察了还原温度和负载量对催化剂表面形成Pd Zn合金过程的影响,并通过适当的后处理过程制备了氧化锌纳米线外延生长Pd Zn纳米粒子催化体系.结果表明,当金属钯负载量较低(质量分数约为2%)时,经400℃还原后的催化剂表面会形成PdxZny(xy)合金,从而影响催化剂的CO选择性;提高钯负载量或还原温度有利于将PdxZny(xy)合金转化为Pd Zn合金,降低CO选择性.负载Pd Zn合金纳米粒子与氧化锌纳米线载体之间外延生长的界面关系使其在甲醇水蒸气重整反应中显示出优异的反应稳定性.     

助剂SiO2对CO2加氢制二甲醚催化剂Cu-ZnO/HZSM-5性能的影响

 考察了助剂SiO2对CO2加氢合成二甲醚催化剂Cu-ZnO/HZSM-5性能的影响,并用X射线衍射、程序升温还原和X射线光电子能谱等手段对催化剂进行了表征. 结果表明,加入少量的SiO2即可显著提高CO2的转化率、二甲醚的选择性以及二甲醚和甲醇的总选择性,并降低副产物CO的选择性,同时改善催化剂的稳定性; 但SiO2加入量大时,催化活性反而降低. SiO2的存在可使焙烧后催化剂的晶型结构发生改变,促进CuO和ZnO的分散,并提高CuO的还原温度. SiO2的加入抑制了反应过程中催化剂上Cu0和ZnO晶粒的长大,对活性物种Cu0有稳定作用,从而有利于提高催化剂的活性和稳定性.     

碱金属助剂对 Au-Pt/CeO2 催化剂催化水煤气变换反应活性的影响

 制备了碱金属 M (M = Na, K, Rb 和 Cs) 掺杂的 Au-Pt/CeO2 催化剂, 考察了其催化水煤气变换反应的活性, 并采用 X 射线衍射、H2 程序升温还原、紫外-可见漫反射光谱和 X 射线光电子能谱技术研究了 K 助剂对 Au-Pt/CeO2 催化剂结构和表面性质的影响. 结果表明, 添加少量电负性较低的 K 虽然使 Pt 的还原变得困难, 但有利于 Au 金属态的稳定, 并使催化剂表面 Ce3+ 富集而产生氧空位, 显著提高了 Au-Pt/CeO2 催化剂活性. 当 K 负载量为 0.025%, 反应温度 250 oC 时, CO 转化率可达 95%.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Investigation of Kinetics of Solid-Phase Synthesis of Lithium Orthosilicate

The kinetics of the interaction between lithium carbonate and silica with various degrees of dispersion was investigated by TG and DTA methods. It was found that the utilization of pyrogenic silica with a specific surface area of about 300 m²g^-1 instead of aerosil with one of 175 m²g^-1 leads to an increase of the reaction rate between lithium carbonate and silica, which depends on the formation and growth of lithium orthosilicate crystals in the first stage, and is conditioned by the diffusion of lithium and oxygen ions through the lithium orthosilicate layer formed at temperatures above 800 K. This supposition is supported by the kinetic analysis results obtained with the use of the different models. The optimal regime of heating is recommended. This revised version was published online in July 2006 with corrections to the Cover Date.     

小环化合物中饱和碳质子化学位移的计算

小环化合物由于其张力、构型、构象和各向异性效应等原因,环碳上质子化学位移缺乏规律性,难以预测,对此作者曾提出一种近似算法。本文根据303种小环化合物中饱和碳质子的化学位移实验数据,将适于计算这类质子化学位移的公式表述为:     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

结合实际发展电化学科学─—武汉大学电化学研究室工作简介

结合实际发展电化学科学─—武汉大学电化学研究室工作简介查全性,陆君涛（武汉大学化学系电化学研究室,武汉４３００７２）在物理化学的众多分支学科中,电化学长期保持良好的发展势头。除了电化学所研究的体系（溶液、电极／溶液界面等）具有广泛的基础意义外,促使电...