周期性扇形孔结构对斜槽型纵扭复合模态超声振动系统性能的影响*

为了解决基于斜槽结构的模式转换型纵扭复合模态超声振动系统存在的扭转分量较小、纵、扭转化效率较低的问题,论文对基于周期性扇形孔和斜槽结构的模式转换型纵扭复合模态超声振动系统进行了研究,主要仿真分析了扇形孔结构参数对基于斜槽结构的模式转换型纵扭复合模态超声振动系统谐振频率、扭转振幅、旋转角度和剪切应力的影响规律,并找到使系统获得最佳纵扭转换效率的扇形孔结构参数,且求解出扇形孔结构的引入对系统性能的改善幅度。     

新型柱孔式模式转换型纵-扭复合模态超声振动系统*

为了改善基于螺旋槽结构和斜槽结构的模式转换型纵-扭复合模态超声振动系统存在的结构复杂、扭转分量较小等问题,论文提出了基于新型柱孔式复合变幅杆的模式转换型纵-扭复合模态超声振动系统,并利用有限元法和数据分析对其进行了仿真分析,结果表明,引入新型柱孔式复合变幅杆的系统的输出端面的剪切应力、旋转角度得到了大幅提升,能够有效地提高纵、扭振动的转换效率。     

超声辅助滚压系统的设计与研究*

鉴于风力发电机组主轴的复杂工作情况和疲劳断裂失效形式,提出一种基于表面强化技术的超声辅助滚压加工系统;首先基于运动合成原理,获得了滚轮接触线的运动轨迹特征,并应用ANSYS/LS-DYNA软件分析了加工过程的特点;之后,基于一维振动理论、等效波长理论与牛顿迭代理论,推导了并求解了复合变幅杆的频率方程,实现了该复合变幅杆的纵向振动。通过对该变幅杆进行有限元仿真分析与振动特性测试,结果表明二者相对设计频率的偏差仅在0.817％以内。最后,通过对40Cr主轴进行超声辅助滚压测试,结果获得了粗糙度Ra 0.085μm和表面硬度32.2HRC的加工表面,较普通滚压加工粗糙度降低了69.1％,显微硬度提高了60％。     

超声辅助滚压系统研究

鉴于风力发电机组主轴的复杂工作情况和疲劳断裂失效形式,提出一种基于表面强化技术的超声辅助滚压加工系统。首先基于运动合成原理,获得了滚轮接触线的运动轨迹特征,并应用ANSYS/LS-DYNA软件分析了加工过程的特点。之后,基于一维振动理论、等效波长理论与牛顿迭代理论,推导并求解了复合变幅杆的频率方程,实现了该复合变幅杆的纵向振动。通过对该变幅杆进行有限元仿真分析与振动特性测试,结果表明二者相对设计频率的偏差仅在0.817%以内。最后,通过对40Cr主轴进行超声辅助滚压测试,获得了粗糙度Ra 0.085μm和表面硬度32.2 HRC的加工表面,较普通滚压加工粗糙度降低了69.1%,显微硬度提高了60%。     

低温微量超声雾化声学系统

针对低温微量超声雾化声学系统中的关键部件单波长超声雾化喷嘴进行研究。首先基于等效电路原理和传输矩阵法分别建立了带中心孔换能器和带中心孔复合变幅杆的频率方程,并应用数学分析软件获得了准确的数值解,实现了超声雾化喷嘴的全谐振。然后,对其进行有限元动力学分析和振动特性测试,结果表明二者相对于设计频率25 kHz的偏差率在0.6%以内,且空载超声振幅达13.5μm。之后,应用流体仿真分析软件对砂轮-工件磨削区进行流场特性分析,结果表明低温微量超声雾化声学系统可以解决磨削区涡流现象的产生。最后,通过对该系统使用前后两种润滑方式的磨削结果进行测试发现：低温微量超声雾化润滑不仅切削液使用量少,而且可以避免工件表面出现烧伤和硬度降低。     

纵-扭谐振超声滚压系统设计与试验

为实现6061铝合金高效优质表面强化,采用有限元仿真法优化设计了阶梯型纵-扭谐动变幅杆,设计、制造了一套纵-扭超声滚压试验装置。纵-扭谐动通过检测变幅杆输出端纵向、扭转两个方向的振幅间接验证。进行超声滚压试验,结果表明：相比普通滚压加工,纵-扭谐振超声滚压过试件表层显微硬度最高提高了41%;在所选参数范围内出现随着静压力增大表面显微硬度整体呈现局部变化整体增大趋势,随着转速增加呈现局部变化整体减小的趋势,随着进给量的增大先增大后减小的现象;相比普通滚压加工,纵-扭谐振超声滚压过的工件表面组织更细密光滑,滚痕由于扭振的高频反复挤压明显减少,形貌得到了较大改善,从而证明纵-扭超声滚压加工能更有效的实现6061铝合金的强化处理。     

三梁纵弯扭超声驻波电机

论述三梁纵弯扭超声驻波电机的结构及原理．重点用F．E．M．方法研究了三梁纵弯扭耦合振子的动态特性．给出了振动频率和振型随耦合振子结构尺寸的变化规律，并对所研制的实验驻波电机性能进行了测试，还研制了驱动电路．这种电机运行性能优于已有的单梁纵弯扭驻波电机，具有广阔的应用前景．     

阵列式压电振子超声复合喷丸强化*

为了进一步改善超声喷丸强化质量,提升工件表面残余应力和显微硬度的均匀性,对压电振子阵列型超声喷丸强化加工系统进行了改进,提出了在强化加工过程中辅助工件往复运动的方法。对改进后的压电振子阵列型超声喷丸强化加工原理进行了阐述,分析了激振片的振动特性并进行了结构尺寸优化,应用Abaqus对工件往复运动下超声喷丸强化过程进行了仿真研究,分析了在不同的工件往复运动频率下,工件表面残余应力分布情况。实验测试了在不同喷丸强化时间及工件往复运动频率下超声喷丸强化加工质量,探究了喷丸时间和工件往复运动频率对工件表面显微硬度的影响。结果表明：在压电振子阵列型超声喷丸强化过程中辅助工件往返运动,可以有效提高工件表面残余应力和显微硬度分布的均匀性,工件表面强化质量得到提升。     

超声振动系统的纵-弯和扭-弯复合振动

对超声变幅杆以及变幅杆与夹心换能器组成的振动系统的纵－弯和扭－弯复合振动进行了研究．变幅杆是任意变截面杆,弯曲振动分析是基于Ｔｉｍｏｓｈｅｎｋｏ理论．理论结果进行了实验验证．     

四激励二维正交复合夹心式压电超声换能器的设计

提出了一种四激励二维正交复合夹心式压电超声换能器,换能器由四组纵向极化压电陶瓷晶堆、一个中心耦合金属块和四个外部金属圆锥组成。基于二维耦合振动机理和机电类比原理,建立了换能器的等效电路模型并推导了其谐振频率方程。利用有限元软件仿真分析了四激励正交复合换能器的频响特性和振动特性,并与其单独一个方向振子的振动特性进行了对比。加工了反相和同相模态的换能器,利用阻抗分析仪和激光测振仪测试了其频率响应和二维四向纵振动输出特性,并进行了大功率二维四向超声乳化实验测试。理论、仿真和实验结果表明:换能器具有反相和同相两个纵向正交共振模态,在这两种共振模态下均可实现二维四向纵振动输出,且换能器两个正交方向振子的纵向振动具有相互耦合加强的作用;等效电路法和有限元法所得换能器的共振频率和有效机电耦合系数与实验测试结果吻合,通过与单激励正交复合夹心式压电超声换能器的有效机电耦合系数对比,发现该换能器具有更高的有效机电耦合系数。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.