Low Pressure Chemical Vapor Deposition of III/V-Nitrides Using Organometallics and Hydrazoic Acid Precursors

In and Ga nitride films have been deposited on various substrates using organometallics and hydrazoic acid (HN₃) as nitrogen precursor. The film deposition was carried out under low pressure (10^?510 ^?6 Torr) and low V/III ratios (1-10). XPS analysis indicated that the ln(Ga):N atomic ratio of unity can be easily achieved by adjusting the experimental conditions. For the growth of InN on Si(100) substrate, 308-nm photon beam is needed to speed up the film deposition rate. He(II) UPS spectra of InN films are in good agreement with the result of a pseudo-potential calculation for InN valence band, while the spectra of GaN compare favorably with a recent semi-ab-initio calculation and with the UPS results of GaN single crystal films. The bandgap of our GaN films is ～ 3.3 cV as determined by photoluminescence and UV-VIS absorption spectra. Raman spectra taken from GaN Films showed peaks at 66 and 88 meV for TO and LO phonons, respectively, indicating a wurtzite structure of the GaN. In a corresponding X-ray diffraction spectrum, the (002) peak is about 400 times more intense than that of the (101) peak, suggesting that the GaN layers are highly oriented with the c-axis normal or nearly so to the Al₂O₃ substrate.     

Continuous Dehydrogenation of n‐Pentanol over a Cr Modified Cu/γ‐Al2O3‐La2O3 Catalyst

The oxidant‐free dehydrogenation of n‐pentanol over copper based catalysts was investigated in this paper. The effect of metal modification on the activity and stability of the copper catalyst supported on γ‐Al₂O₃ and La₂O₃ (Cu/γ‐Al₂O₃‐La₂O₃) was clarified and a Cr modified Cu/Al₂O₃‐La₂O₃ (Cu‐Cr/γ‐Al₂O₃‐La₂O₃) showed the best catalytic performance. The conversion of n‐pentanol was 70.0% and the selectivity for n‐pentanal increased to 97.1% over Cu‐Cr/γ‐Al₂O₃‐La₂O₃. X‐ray diffraction and temperature programmed reduction of H₂ indicated that the addition of Cr favors the formation and reduction of the copper oxide, and the dispersion of the active Cu⁰ species, accounting for the good activity and stability of this catalyst. Furthermore, the lower amount of acidic sites in Cu‐Cr/γ‐Al₂O₃‐La₂O₃ is suggested to suppress the dehydration in oxidant‐free dehydrogenation of n‐pentanol, accounting for the higher selectivity for n‐pentanal.     

Morphology,tensile properties,and fracture toughness of epoxy/Al2O3 nanocomposites

Epoxy/Al₂O₃ nanocomposites were prepared using an epoxy resin, diglycidyl ether of bisphenol A, and cured with a polyoxypropylene diamine (Jeffamine D‐400). Transmission electron microscopy and wide angle X‐ray diffraction were employed to reveal the morphology of epoxy/Al₂O₃ nanocomposites. Dynamic mechanical analysis results showed that the storage modulus and the glass transition temperature (T_g) of epoxy were improved. Tensile strength and Young's modulus also increased with increasing Al₂O₃ loading. Fracture toughness, as indicated by the stress intensity factor, K_Q, was determined using single edge notch bending method, and 40% increase in K_Q was observed with only 2 vol % Al₂O₃. Scanning electron microscopy study of fracture surface showed a rather smooth and flat morphology for neat epoxy. However, massive plastic deformation was observed for epoxy/Al₂O₃ nanocomposites, leading to the significant increase in fracture toughness. The influence of spherical Al₂O₃ nanoparticles on thermophysical properties of epoxy was discussed and compared with that of sheet‐like nanoclays. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1466–1473, 2006     

Preparation of nanoalumina/EPDM composites with good performance in thermal conductivity and mechanical properties

In this paper, nanoalumina (Al₂O₃) highly filled ethylene propylene diene monomer (EPDM) composites are prepared, and the mechanical (static and dynamic) properties and thermal conductivity are investigated systemically through various characterization methods. Furthermore, influences of in situ modification (mixing operation assisted by silane at high temperature for a certain time) with the silane‐coupling agent bis‐(3‐triethoxy silylpropyl)‐tetrasulfide (Si69) and stearic acid (SA) pretreatment on the nano‐Al₂O₃ filled composites are as well investigated. The results indicate that nano‐Al₂O₃ particles can not only perform well in reinforcing EPDM, but also improve the thermal conductivity significantly. Assisted by in situ modification with Si69, the mechanical properties (especially dynamic mechanical properties) of the nano‐Al₂O₃ filled composites are improved obviously, without influencing the thermal conductivity. By comparing to the traditional reinforcing fillers, such as carbon black (grade N330) and silica, in situ modified nano‐Al₂O₃ filled composites exhibit excellent performance in mechanical (static and dynamic) properties as well as better thermal conductivity, especially lower compression heat build‐up and better fatigue resistance. In general, our work indicates that nano‐Al₂O₃, as the novel thermal conductive reinforcing filler, is suitable to prepare rubber products serving in dynamic conditions, with the longer expected service life. Copyright © 2010 John Wiley & Sons, Ltd.     

A Novel Way to Prepare TiO2 and γ‐Al2O3 Supported Catalysts with Large Surface Areas

Several TiO₂ and γ‐Al₂O₃ supported catalyst systems were prepared by a novel way and characterized by X‐ray diffraction, Raman spectroscopy and BET surface area measurement. The results show: (1) all the samples, including MoO₃/TiO₂, WO₃/TiO₂, V₂O₅/TiO₂, FeSO₄/γ‐Al₂O₃, Al₂ (SO₄)₃/γ‐Al₂O₃, K₂CO₃/‐Al₂O₃ and so on, prepared by impregnating TiO₂·H₂O or pseudo‐boehmite AlO(OH) with the active components then calcining at a high temperature exhibit much larger surface areas than that of pure TiO₂ or γ‐Al₂O₃ calcined at the same temperature; (2) the surface area of the sample increases with the increase in the coverage of active component on the surface of the support; (3) when the content of active component reaches its utmost monolayer dispersion capacity, the surface area of the sample is the largest, and then decreases when the content of active component exceeds its dispersion threshold.     

Production of 5‐Hydroxymethylfurfural from Fructose in Ionic Liquid Efficiently Catalyzed by Cr(III)‐Al2O3 Catalyst

A series of metal‐Al₂O₃ catalysts were prepared simply by the conventional impregnation with Al₂O₃ and metal chlorides, which were applied to the dehydration of fructose to 5‐hydroxymethylfurfural (HMF). An agreeable HMF yield of 93.1% was achieved from fructose at mild conditions (100°C and 40 min) when employing Cr(III)‐Al₂O₃ as catalyst in 1‐butyl‐3‐methylimidazolium chloride ([Bmim]Cl). The Cr(III)‐Al₂O₃ catalyst was characterized via XRD, DRS and Raman spectra and the results clarified the interaction between the Cr(III) and the alumina support. Meanwhile, the reaction solvents ([Bmim]Cl) collected after 1^st reaction run and 5^th reaction run were analyzed by ICP‐OES and LC‐ITMS and the results confirmed that no Cr(III) ion was dropped off from the alumina support during the fructose dehydration. Notably, Cr(III)‐Al₂O₃ catalyst had an excellent catalytic performance for glucose and sucrose and the HMF yields were reached to 73.7% and 84.1% at 120°C for 60 min, respectively. Furthermore, the system of Cr(III)‐Al₂O₃ and [Bmim]Cl exhibited a constant stability and activity at 100°C for 40 min and a favorable HMF yield was maintained after ten recycles.     

Efficient conversion of fructose to 5‐hydroxymethylfurfural by functionalized γ‐Al2O3 beads

Millimeter size γ‐Al₂O₃ beads were prepared by alginate assisted sol–gel method and grafting organic groups with propyl sulfonic acid and alkyl groups as functionalized γ‐Al₂O₃ bead catalysts for fructose dehydration to 5‐hydroxymethylfurfural (5‐HMF). Experiment results showed that the porous structure of γ‐Al₂O₃ beads was favorable to the loading and dispersion of active components, and had an obvious effect on the properties of the catalyst. The lower calcination temperature of γ‐Al₂O₃ beads increased the specific surface area, the hydrophobicity and the activity of catalysts. Competition between the reaction of alkyl groups and ‐SH groups with surface hydroxyl during the preparation process of the catalyst influenced greatly the acid site densities, hydrophobic properties and activity of the catalyst. With an increase in the alkyl group chain, the hydrophobicity of catalysts increased obviously and the activity of the catalyst was enhanced. The most hydrophobic catalyst C₁₆‐SO₃H‐γ‐Al₂O₃–650°C exhibited the highest yield of 5‐HMF (84%) under the following reaction conditions: reaction medium of dimethylsulfoxide/H₂O (V/V, 4:1), catalyst amount of 30 mg, temperature of 110°C and reaction time of 4 hr.     

Eliminated Phototoxicity of TiO2 Particles by an Atomic‐Layer‐Deposited Al2O3 Coating Layer for UV‐Protection Applications

We demonstrate the conformal coating of an ultrathin Al₂O₃ layer on TiO₂ nanoparticles through atomic layer deposition by using a specifically designed rotary reactor to eliminate the phototoxicity of the particles for cosmetic use. The ALD reactor is modified to improve the coating efficiency as well as the agitation of the particles for conformal coating. Elemental and microstructural analyses show that ultrathin Al₂O₃ layers are conformally deposited on the TiO₂ nanoparticles with a controlled thickness. Rhodamine B dye molecules on Al₂O₃‐coated TiO₂ exhibited a long life time under UV irradiation, that is, more than 2 h, compared to that on bare TiO₂, that is, 8 min, indicating mitigation of photocatalytic activity by the coated layer. The effect of carbon impurities in the film resulting from various deposition temperatures and thicknesses of the Al₂O₃ layer on the photocatalytic activity are also thoroughly investigated with controlled experimental condition by using dye molecules on the surface. Our results reveal that an increased carbon impurity resulting from a low processing temperature provides a charge conduction path and generates reactive oxygen species causing the degradation of dye molecule. A thin coated layer, that is, less than 3 nm, also induced the tunneling of electrons and holes to the surface, hence oxidizing dye molecules. Furthermore, the introduction of an Al₂O₃ layer on TiO₂ improves the light trapping thus, enhances the UV absorption.     

Enhanced Water Oxidation Activity on Ni,Co-Doped Fe2O3 (0001) Surface

Fe based oxides are considered as a promising catalyst for the oxygen evolution reaction (OER) due to their low cost and high stability. Here, based on density functional theory calculations, the electrocatalytic behaviors of pure and metal (Ni, Co) doped Fe-terminated Fe₂O₃(0001) are investigated. The potential-limiting step for OER is determined as the formation of O^* by dehydrogenating surface hydroxyl and it is suggested that the doping enhances the catalytic activity of Fe₂O₃(0001) by reducing the free energy change of rate limiting step on doped Ni or Co atom. Especially, the calculated over-potential of Co-doped Fe₂O₃ (0001) surface is about 0.63 eV on Co site, which is comparable with the theoretical over-potential of 0.56 eV for RuO₂.     

己内酰胺一步法氢化烷基化合成N-烷基环己亚胺

A new synthetic method for the preparation of N-alkylhexahydroazepine by one-step catalytic alkylation and hydrogenation of caprolactam has been developed. Alkylated caprolactam was firstly synthesized by catalytic alkylation of caprolactam with alcohol and then directly hydrogenated into N-alkylhexahydroazepine over Cu-ZnO/γ-Al2O3 catalyst.     

Catalytic Performance and Characterization of Pt‐Co/Al2O3 Catalysts for CO2 Reforming of CH4 to Synthesis Gas

Pt‐Co/Al₂O₂ catalyst has been studied for CO₂ reforming of CH₄ to synthesis gas. It was found that the catalytic performance of me catalyst was sensitive to calcination temperature. When Co/Al₂O₃ was calcined at 1473 K prior to adding a small amount of Pt to it, the resulting bimetallic catalyst showed high activity, optimal stability and excellent resistance to carbon deposition, which was more effective to the reaction than Co/Al₂O₃ and Pt/Al₂O₃ catalysts. At lower metal loading, catalyst activity decreased in the following order: Pt‐Co/ Al₂O₃ > Pt/Al₂O₃ > Co/Al₂O₃. With 9% Co, the Co/Al₂O₃ calcined at 923 K was also active for CO₂ reforming of CH₄, however, its carbon formation was much more fast man that of the Pt‐Co/Al₂O₃ catalyst. The XRD results indicated that Pt species well dispersed over the bimetallic catalyst. Its high dispersion was related to the presence of CoAl₂O₄, formed during calcining of Co/Al₂O₃ at high temperature before Pt addition. Promoted by Pt, Co/Al₂O₄ in the catalyst could be reduced partially even at 923 K, the temperature of pre‐reduction for the reaction, confirmed by TPR. Based on these results, it was considered that the zerovalent platinum with high dispersion over the catalyst surface and the zerovalent cobalt resulting from Co/Al₂O₄ reduction are responsible for high activity of the Pt‐Co/Al₂O₃ catalyst, and the remain Co/Al₂O₄ is beneficial to suppression of carbon deposition over the catalyst.     

Nano n‐propylsulfonated γ‐Al2O3: a new,efficient and reusable catalyst for synthesis of spiro[indoline‐3,4‐pyrazolo[3,4‐e][1,4]thiazepine]diones in aqueous media

Nano n‐propylsulfonated γ‐Al₂O₃ is easily prepared by the reaction of nano γ‐Al₂O₃ with 1,3‐propanesultone. This reagent can be used as an efficient catalyst for the synthesis of spiro [indoline‐3,4‐pyrazolo[3,4‐e][1,4]thiazepine]diones in aqueous media. This new method consistently has the advantages of excellent yields and short reaction times. Further, the catalyst can be reused and recovered several times. Copyright © 2013 John Wiley & Sons, Ltd.     

Effect of surface treatments on interfacial characteristics and band alignments of atomic‐layer‐deposited Al2O3 films on GaAs substrates

The GaAs surfaces were passivated by two kinds of chemical pretreatments (using NH₄OH and (NH₄)₂S as passivation agents) for atomic layer deposited (ALD) Al₂O₃ dielectric film growth. The chemical information at Al₂O₃/GaAs interfaces was carefully characterized. The impact of surface treatments on the band alignments of ALD Al₂O₃ films on n? GaAs (100) substrates was also investigated. After postdeposition annealing, the NH₄OH passivated samples not only have a slight increase of the As? As peaks with an appearance of As suboxide (AsO_x) feature at Al₂O₃/GaAs interfaces but also exhibit a serious interfacial interdiffusion between Al₂O₃ and GaAs. However, the (NH₄)₂S passivated samples produce the Ga? S and As? S overlayers on GaAs, effectively preventing from the intermixed diffusion between Al₂O₃ films and GaAs substrates with a sharper interface. Both NH₄OH and (NH₄)₂S passivated Al₂O₃ samples show the same band gap of 6.67 eV. The conduction band offset at Al₂O₃/GaAs interface for the (NH₄)₂S passivated samples have a slight enhancement of 0.14 eV in comparison to NH₄OH passivated ones. Copyright © 2010 John Wiley & Sons, Ltd.     

Scanning force microscopy and amplitude versus distance measurements on single‐crystal oxide surfaces

Dynamic mode imaging and investigations on amplitude versus distance measurements were carried out on surfaces of single‐crystal; SrTiO₃, Al₂O₃ and LaAlO₃. Experiments were performed to optimize the imaging parameters for surfaces having varying elastic properties. The dependence of the amplitude–distance curve on different materials and the amplitude of oscillation was investigated. For SrTiO₃, a low‐drive amplitude provided the linear region necessary for imaging. A large amplitude of oscillation, however, created dips in the amplitude–distance curves, presumably due to complications in the tip dynamics such as bifurcation, period doubling, etc. In the case of Al₂O₃ and LaAlO₃, amplitude–distance curves were characterized by oscillations for lower tip sample separations and step‐like discontinuities in the stiff region. The magnitude of the oscillations and discontinuities was found to decrease with amplitude and eventually could be eliminated. Thus, for these samples a large amplitude of the cantilever provided the linear region required for imaging. It was observed also that two different surfaces of Al₂O₃ (c‐cut and r‐cut) yield totally different amplitude–distance curves consistent with their standard differences. The results indicate the complex behaviour of amplitude–distance curves, which not only vary from one sample to another but from one surface to another for a given sample. Copyright © 2004 John Wiley & Sons, Ltd.     

Enhanced dielectric performance and energy storage of PVDF‐HFP‐based composites induced by surface charged Al2O3

In order to enhance dielectric properties and energy storage density of poly(vinylidene fluoride‐hexafluoro propylene) (PVDF‐HFP), surface charged gas‐phase Al₂O₃ nanoparticles (GP‐Al₂O₃, with positive surface charges, ε’ ≈ 10) are selected as fillers to fabricate PVDF‐HFP‐based composites via simple physical blending and hot‐molding techniques. The results show that GP‐Al₂O₃ are dispersed homogeneously in the PVDF‐HFP matrix and the existence of nanoscale interface layer (matrix‐filler) is investigated by SAXS. The dielectric constant of the composites filled with 10 wt % GP‐Al₂O₃ is 100.5 at 1 Hz, which is 5.6 times higher than that of pure PVDF‐HFP. The maximum energy storage density of the composite is 4.06 J cm^?3 at an electrical field of 900 kV mm^?1 with GP‐Al₂O₃ content of 1 wt %. Experimental results show that GP‐Al₂O₃ could induce uniform fillers’ distribution and increase the concentration of electroactive β‐phase as well as enhance interfacial polarization in the matrix, which resulted in enhancements of dielectric constant and energy storage density of the PVDF‐HFP composites. This work demonstrates that surface charged inorganic‐oxide nanoparticles exhibit promising potential in fabricating ferroelectric polymer composites with relatively high dielectric constant and energy storage. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 574–583     

Selective catalytic reduction of NO over metal oxide or noble metal-doped In2O3/Al2O3 catalysts by propene in the presence of oxygen

The activities of metal oxide CuO, SnO₂, CoO, Ag₂O, ZnO or noble metal Pt, Pd, Rh-doped In₂O₃/Al₂O₃ catalysts for selective catalytic reduction of NO by propene were investigated. The temperature windows for NO reduction over noble metal-doped In₂O₃/Al₂O₃ catalysts were shifted and broaden slightly compared with single component catalyst alone. This revised version was published online in June 2006 with corrections to the Cover Date.     

Solvent‐free synthesis of propargylamines catalyzed by an efficient recyclable ZnO‐supported CuO/Al2O3 nanocatalyst

An efficient nanocatalyst of ZnO‐supported CuO/Al₂O₃ (CuO/ZnO/Al₂O₃ nanocatalyst) was prepared by the co‐precipitation method and characterized by scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, X‐ray powder diffraction and Brunauer–Emmett–Teller surface area analysis. CuO/ZnO/Al₂O₃ nanocatalyst proved to be a very efficient catalyst on the synthesis of propargylamines under solvent‐free conditions in high yields. Moreover, the catalyst can be recyclable without reducing catalytic activity up to five times.     

The Ionic Conductivity of Ultrafine Solid Electrolytes for Li4.4Al0.4Si0.6O4‐xY2O3 Systems

The Li_4.4Al_0.4Si_0.6O₄‐xY₂O₃ (x = 0 to 0.5) ion conductors were prepared by the Sol‐Gel method and examined in detail. The powder and sintered samples were characterized by DTA‐TG, XRD, SEM, and AC impedance techniques. The experimental results show that the conductivity and sinterability increased with the amount of excess Y₂O₃ in the silicate. The particle size of the powder samples is about 0.12 μm. The maximum conductivity at 16 °C is 2.925 × 10^?5s·cm^?1 for Li_4.4Al_0.4Si_0.6O₄‐0.3 Y₂O₃.     

Thermally conductive and electrically insulative nanocomposites based on hyperbranched epoxy and nano‐Al2O3 particles modified epoxy resin

Novel epoxy nanocomposites based on a diglycidyl ether of bisphenol A (DGEBA) epoxy, an epoxy functionalized hyperbranched polymer (HTTE) and nano‐Al₂O₃ were synthesized with the aim of determining the effect of the nano‐Al₂O₃ particles and HTTE on the structure and properties of epoxy nanocomposites. The mechanical properties, thermal conductivity, bulk resistivity, and thermal stability of the nano‐Al₂O₃/HTTE/DGEBA ternary composites were evaluated and compared with the corresponding matrix. The improvement in impact properties of these nanocomposites was explained in terms of fracture surface analysis by SEM. The results indicate that the incorporation of nanoparticles and hyperbranched epoxy effectively improved the toughness of epoxy composites without sacrificing thermal conductivity and bulk resistivity compared to the neat epoxy and Al₂O₃/DGEBA, obtaining a well dispersion of nanoparticles in epoxy matrix and solving the drawbacks for single fillers filled epoxy nanocomposite. Copyright © 2010 John Wiley & Sons, Ltd.     

Novel Flower‐Like Ag‐SiO2‐MgO‐Al2O3 Material: Preparation,Characterization and Catalytic Application in Methanol Dehydrogenation

Catalytic direct dehydrogenation of methanol to formaldehyde was carried out over Ag‐SiO₂‐MgO‐Al₂O₃ catalysts prepared by sol‐gel method. The optimal preparation mass fractions were determined as 8.3% MgO, 16.5% Al₂O₃ and 20% silver loading. Using this optimum catalyst, excellent activity and selectivity were obtained. The conversion of methanol and the selectivity to formaldehyde both reached 100%, which were much higher than other previously reported silver supported catalysts. Based on combined characterizations, such as X‐ray diffraction (XRD), scanning electronic microscopy (SEM), diffuse reflectance ultraviolet‐visible spectroscopy (UV‐Vis, DRS), nitrogen adsorption at low temperature, temperature programmed desorption of ammonia (NH₃‐TPD), desorption of CO₂ (CO₂‐TPD), etc., the correlation of the catalytic performance to the structural properties of the Ag‐SiO₂‐ MgO‐Al₂O₃ catalyst was discussed in detail. This perfect catalytic performance in the direct dehydrogenation of methanol to formaldehyde without any side‐products is attributed to its unique flower‐like structure with a surface area less than 1 m²/g, and the strong interactions between neutralized support and the nano‐sized Ag particles as active centers.