The influence of the sample introduction system on signals of different tin compounds in inductively coupled plasma-based techniques

The influence of the sample introduction system on the signals obtained with different tin compounds in inductively coupled plasma (ICP) based techniques, i.e., ICP atomic emission spectrometry (ICP–AES) and ICP mass spectrometry (ICP–MS) has been studied. Signals for test solutions prepared from four different tin compounds (i.e., tin tetrachloride, monobutyltin, dibutyltin and di-tert-butyltin) in different solvents (methanol 0.8% (w/w), i-propanol 0.8% (w/w) and various acid matrices) have been measured by ICP–AES and ICP–MS. The results demonstrate a noticeable influence of the volatility of the tin compounds on their signals measured with both techniques. Thus, in agreement with the compound volatility, the highest signals are obtained for tin tetrachloride followed by di-tert-butyltin/monobutyltin and dibutyltin.The sample introduction system exerts an important effect on the amount of solution loading the plasma and, hence, on the relative signals afforded by the tin compounds in ICP–based techniques. Thus, when working with a pneumatic concentric nebulizer, the use of spray chambers affording high solvent transport efficiency to the plasma (such as cyclonic and single pass) or high spray chamber temperatures is recommended to minimize the influence of the tin chemical compound. Nevertheless, even when using the conventional pneumatic nebulizer coupled to the best spray chamber design (i.e., a single pass spray chamber), signals obtained for di-tert-butyltin/monobutyltin and dibutyltin are still around 10% and 30% lower than the corresponding signal for tin tetrachloride, respectively. When operating with a pneumatic microconcentric nebulizer coupled to a 50 °C-thermostated cinnabar spray chamber, all studied organotin compounds provided similar emission signals although about 60% lower than those obtained for tin tetrachloride. The use of an ultrasonic nebulizer coupled to a desolvation device provides the largest differences in the emission signals, among all tested systems.     

Analysis for metallothioneins using coupled techniques

Analytical chemistry of metallothioneins based on the coupling of a high resolution separation technique with an element or species selective detection technique is discussed. The role of size-exclusion chromatography (SEC) with on-line atomic spectrometric detection for the quantification of metallothionein fraction in cell cytosols is evaluated. Particular attention is given to the conditions for the separation of metallated metallothionein isoforms (MT-1, MT-2, MT-3) and sub-isoforms within these classes by anion-exchange and reversed-phase HPLC. Techniques for interfacing chromatography with atomic absorption spectrometry (AAS), inductively coupled plasma atomic emission spectrometry (ICP AES) and ICP mass spectrometry (MS) are assessed. The potential of electrospray (tandem) mass spectrometry for the characterization of metallothionein isoforms with respect to molecular mass and aminoacid sequence is highlighted. Perspectives for capillary zone electrophoresis (CZE), microbore and capillary HPLC with ICP MS and electrospray MS(/MS) detection for the probing of metallothioneins are discussed. Applications of hyphenated techniques to the analysis of real-world samples are reviewed.     

Development of gas-phase sample-introduction techniques for analytical atomic spectrometry.

For the last 30 years, several types of gas-phase sample-introduction methods in analytical atomic spectrometry, i.e., atomic absorption spectrometry (AAS), atomic emission spectrometry (AES) and atomic fluorescence spectrometry (AFS), have been investigated and developed in the author's laboratory. Their fundamental results are summarized in this review article. The gas-phase sample-introduction techniques developed in the author's laboratory can be roughly divided into four groups: i) hydride generation, ii) cold-vapor generation of mercury, iii) analyte volatilization reactions and iv) miscellaneous. The analytical figures of merit of the gas-phase sample-introduction methods have been described in detail. Hydride generation has been coupled with the AAS of As, Bi, Ge, Pb, Sb, Se, Sn and Te, with the inductively coupled plasma (ICP) AES of As, Bi, Sn, Se and Sb, with the high-power nitrogen microwave-induced plasma (N2-MIP) AES of As, Bi, Pb, Sb, Se, Sn and Te by their single- and multi-element determinations, with the AFS of As, Bi, Pb, Sb, Se, Sn and Te, and with the ICP mass spectrometry (MS) of As and Se. The cold-vapor generation method for Hg has been combined with atmospheric-pressure helium microwave-induced plasma (He- or Ar-MIP)-AES and AFS. Furthermore, analyte volatilization reactions have been employed in the ICP-AES of iodine, in the He-MIP-AES of iodine bromine, chlorine, sulfur and carbon, and in the ICP-MS of sulfur. As a result, when compared with conventional solution nebulization, a great improvement in the sensitivity has been attained in each instance. In addition, the developed techniques coupled with analytical atomic spectrometry have been successfully applied to the determination of trace elements in a variety of practical samples.     

Using of Fractional Separation for the Analysis of MoO<Subscript>3</Subscript> by Atomic Emission Spectrometry with Inductively Coupled Plasma and Electrothermal Vaporization

The introduction of various forms of molybdenum into an inductively coupled plasma was studied in the vaporization of solutions from a graphite tube. A temperature program is selected that enables the separated vaporization of analytes and molybdenum (matrix) for atomic emission spectrometry with inductively coupled plasma and electrothermal vapoization (ETV–ICP–AES) analysis. The limits of detection for analytes in the ETV–ICP–AES analysis of molybdenum trioxide are evaluated using the fractional separation of analytes and the matrix.     

贵金属元素铂、铑、钯的分析进展

从光度法、电化学法、原子吸收法、中子活化法、电感耦合等离子体与原子发射光谱、质谱联用技术等各种方法,对国内外近几年来贵金属元素铂、铑、钯的测定方法进行综合评述,引用文献168篇。     

Possibilities of the Determination of Matrix Elements of High-Purity Glasses of As–Se and As–S Systems by Inductively Coupled Plasma Atomic Emission Spectrometry

Possibilities of inductively coupled plasma atomic emission spectrometry (ICP AES) as an alternative to X-ray spectrochemical analysis are estimated in the determination of matrix elements of glasses of As–Se and As–S systems. Standard solutions were prepared from pure elements As, Se and S. It was shown that the matrix elements of glasses can be determined with an expanded uncertainty of 0.05–0.1 mol %. The results of determinations by ICP AES and X-ray fluorescence spectrometry were compared; and it was found that by the attained performance characteristics, the results of ICP AES are highly competitive with the data of X-ray fluorescence spectrometry, but do not require sets of adequate solid reference samples.     

Imaging of metals in biological tissue by laser ablation inductively coupled plasma mass spectrometry (LA–ICP–MS): state of the art and future developments

Laser ablation inductively coupled plasma mass spectrometry (LA–ICP–MS) is well established as a sensitive trace and ultratrace analytical technique with multielement capability for bioimaging of metals and studying metallomics in biological and medical tissue. Metals and metalloproteins play a key role in the metabolism and formation of metal‐containing deposits in the brain but also in the liver. In various diseases, analysis of metals and metalloproteins is essential for understanding the underlying cellular processes. LA–ICP–MS imaging (LA–ICP–MSI) combined with other complementary imaging techniques is a sophisticated tool for investigating the regional and cellular distribution of metals and related metal‐containing biomolecules. On the basis of successful routine techniques for the elemental bioimaging of cryosections by LA–ICP–MSI with a spatial resolution between 200 and ~10 µm, the further development used online laser microdissection ICP–MSI to study the metal distribution in small biological sample sections (at the cellular level from 10 µm to the submicrometer range). The use of mass spectrometric imaging of metals and also nonmetals is demonstrated on a series of biological specimens. This article discusses the state of the art of bioimaging of metals in thin biological tissue sections by LA–ICP–MSI with spatial resolution at the micrometer scale, future developments and prospects for quantitative imaging techniques of metals in the nanometer range. In addition, combining quantitative elemental imaging by LA/laser microdissection–ICP–MSI with biomolecular imaging by matrix‐assisted laser desorption/ionization–MSI will be challenging for future life science research. Copyright © 2013 John Wiley & Sons, Ltd.     

Recent advances in the application of mass spectrometry in food-related analysis

A review is presented on recent applications of mass spectrometry (MS)-based techniques for the analysis of compounds of food concern. Substances discussed are naturally occurring compounds in food products such as lipids, oligosaccharides, proteins, vitamins, flavonoids and related substances, phenolic compounds and aroma compounds. Among xenobiotics, applications of MS techniques for the analysis of pesticides, drug residues, toxins, amines and migrants from packaging are overviewed. Advances in the analysis of trace metals of nutritional and toxicological interest by MS with inductively coupled plasma (ICP) source are presented. The main features of mass spectrometry combined with separation instruments are discussed in food-related analysis. Examples of mass spectrometry and tandem MS (MS-MS) are provided. The development and application of matrix-assisted laser desorption ionization (MALDI) and electrospray (ESI) to the analysis of peptides and proteins in food is discussed. This survey will attempt to cover the state-of-the-art up from 1999 to 2001.     

Separation of metal ions by capillary electrophoresis – diversity, advantages, and drawbacks of detection methods

Capillary electrophoresis (CE) has been applied to metal-ion analysis during the last 10 years. To improve sensitivity and selectivity different modes of detection have been adapted or developed. The selection of commercially available detection systems for metal-ion analysis is still primarily limited to UV–Vis detection, although other commercial systems, e.g. fluorescence, conductivity, or interfaces for coupling to mass spectrometry (MS) or inductively coupled plasma mass spectrometry (ICP–MS) are becoming available. High demands are made on any detector used in CE, because the analytical signal has to be extracted from less than 1 nL of sample, which corresponds to a total amount of ≤ 10^–12 to 10^–15 mol analyte. This paper compares currently available and recently developed detection methods for CE as applied to the analysis of metal ions. Commercially available techniques, for example UV– Vis, fluorescence, or mass spectrometry, and other new detection methods including electrochemistry, radioactivity, and XRF, are discussed and future trends are anticipated.     

Determination of Rare Earth Elements in Garnet Minerals,Geological Materials by Inductively Coupled Plasma–Atomic Emission Spectral and Mass Spectral Analysis

Abstract

The performance of inductively coupled plasma–atomic emission spectrometry (ICP‐AES) for the determination of 14 lanthanides and Yttrium was evaluated by comparison with inductively coupled plasma–mass spectral (ICP‐MS) analysis. The geochemical reference samples (GRS), DNC‐1(diabase), AGV‐1(andesite), Sy‐2(syenite), MRG‐1(gabbro), AN‐G(anorthosite), AC‐E(granite), and MAG‐1(marine mud) were chosen as test materials and analyzed for checking the precision and reproducibility of the methods. The mineral garnet is separated from the black sands of the southwest coast of India, and the combined cation exchange–ICP method of AES analysis and MS analysis were carried out for the determination of rare earth elements. Both techniques are within the requirements needed for garnet minerals. The determination of rare‐earth elements in these minerals, which contain other elements as major contribution and trace distribution of rare‐earth elements, shows that ICP applied under the proper working condition lives up to the expectations. Major element analysis gives the formula of garnet of Manavalakurichi (MK) as (FeCaMg)_2.79Al_2.07Si_3.05O₁₂ approximated to Fe₃Al₂Si₃O₁₂, hence of almandine-type garnet. The enrichment of heavy lanthanides compared to the light lanthanides indicates that these lanthanides occupy the coordinaton site of Fe²⁺ by replacement. Both techniques are excellent in determining the very low concentration of lanthanides in geological materials, specifically garnet.     

Preparation and characterization of a set of IAEA reference air filters for quality control in air-pollution studies

Several sets of reference air filters were prepared as part of an IAEA evaluation of the performance of laboratories involved in air-pollution studies. Each set comprised three polycarbonate membrane filters, two of which were loaded with urban air particulate matter (APM) obtained in Vienna or Prague, and one unloaded filter. The filters were loaded by filtration of a suspension of the APM materials in water. The homogeneity both of bulk APM materials and of the loaded filters was evaluated and found suitable by determining several elements by instrumental neutron-activation analysis (INAA), proton-induced X-ray emission (PIXE), and micro-X-ray energy-dispersive fluorescence analysis (μ-EDXRF). After evaluation of the homogeneity, INAA, PIXE, EDXRF, atomic absorption spectrometry (AAS), inductively coupled plasma optical emission spectrometry (ICP–OES), and ICP mass spectrometry (ICP–MS) were used to characterize the filter materials and establish “target values” and their associated standard deviations for 15 elements. Problems encountered during the preparation of these unique, simulated air filters and the criteria for setting both the target values and standard deviations are presented.     

Characterization and screening of metals,metalloids and biomarkers in crude oil by ICP–MS/OES,and GC–MS techniques after digestion by microwave‐induced combustion

A method for digestion of light and medium Iraqi crude oils (Basrah and Khanaken oils) using microwave‐induced combustion (MIC) in closed vessels is described for the determination of Hg, Au, Cu, Al, Ca, Co, K, Mg, Si and Sr by inductively coupled plasma optical emission spectrometry (ICP–OES) and Mo, Ti, Mn, Li, Se^?1, Rb, Ag, Ba, Pb, As, Cd, Cr, Fe, Ni, V and Zn by inductively coupled plasma mass spectrometry (ICP–MS). Upon using MIC it was possible to obtain lower limits of detection by ICP–MS and also by ICP–OES compared with those obtained by microwave‐assisted digestion. The MIC was the best choice with regard to the possibility of using dilute nitric acid as an absorbing solution, which is important to minimize the interference encountered by ICP–MS and ICP–OES.The physicochemical parameters and some contaminants of crude oil samples were analyzed to classify and assess the quality of the crude oils. This study determines the viability of the use of Fourier transform infrared spectroscopy as an alternativee to traditional petroleum geochemical methods for crude oil characterization. The infrared fingerprints agree with the results obtained from GC–MS analysis.     

Inductively coupled plasma mass spectrometry based platforms for studies involving nanoparticle effects in biological samples

The widespread application of nanoparticles (NPs) in recent times has caused concern because of their effects in biological systems. Although NPs can be produced naturally, industrially synthesized NPs affect the metabolism of a given organism because of their high reactivity. The biotransformation of NPs involves different processes, including aggregation/agglomeration, and reactions with biomolecules that will be reflected in their toxicity. Several analytical techniques, including inductively coupled plasma mass spectrometry (ICP‐MS), have been used for characterizing and quantifying NPs in biological samples. In fact, in addition to providing information regarding the morphology and concentration of NPs, ICP‐MS‐based platforms, such as liquid chromatography/ICP‐MS, single‐particle ICP‐MS, field‐flow fractionation (asymmetrical flow field‐flow fractionation)‐ICP‐MS, and laser ablation‐ICP‐MS, yield elemental information about molecules. Furthermore, such information together with speciation analysis enlarges our understanding of the interaction between NPs and biological organisms. This study reports the contribution of ICP‐MS‐based platforms as a tool for evaluating NPs in distinct biological samples by providing an additional understanding of the behavior of NPs and their toxicity in these organisms.     

Inductively coupled plasma mass spectrometry and atomic emission spectrometry coupled to high-performance liquid chromatography for speciation and detection of organotin compounds

Inductively coupled plasma mass spectrometry (ICP/MS) is utilized as a detector for several organotin species separated by high-performance liquid chromatography. Detection limits obtained by ICP/MS are 3 orders of magnitude lower than those obtained with inductively coupled plasma atomic emission spectrometry (ICP/AES) detection under the same chromatographic conditions. Chromatographic detection limits are higher than conventional solution nebulization for the same compound by a factor of 20. Ion-exchange chromatography yields linear response over 3 orders of magnitude, while ion pair chromatography gives a linear response of only 2 orders of magnitude as a result of poor resolution. The relative standard deviation for the injection of 20 ng of tin compounds is less than 10%.     

Flow Injection Coupled Capillary Isotachophoresis to ICP-AES and On-line Determination of Metal Species

A new technique for coupling capillary isotachophoresis (CITP) to Inductive coupled plasmas atomic emission spectrometry (ICP-AES) using flow injection (FI) is developed. Great attention to CITP have been paid owing to its broad application prospect in biochemistry, clinic, pharmacy, food,environment detection and conventional ionic analysis. Its zone-boundary sharpening, large size capillary and self-concentrating effects are different from those of other electrophoretic techniques. Recently, ICP-AES/MS, as a special metal detector, has been combined with the capillary zone electrophoresis (CZE). However, in CZE system, typical sample volume and flow rate are only in the range of 0.02 - 1 μl/min and 0.2-2μl, which results in the difficult for the coupling of CZE and ICP with conventional sampling system and the obtaining enough sensitivity.     

Calibration graphs for steels by IR laser ablation inductively coupled plasma atomic emission spectrometry

Infrared laser ablation (IRLA) was studied as a sample-introduction technique for the analysis of steels by inductively coupled plasma atomic emission spectrometry (ICP–AES). A comparison of two IRLA–ICP–AES systems based on Q-switched nanosecond Nd?:?YAG lasers was performed. The beam of the Lina-Spark atomizer (LSA Sarl, Cully, Switzerland) based on the Surelite I-20 laser (Continuum, USA) was moved along a circle. A Perkin–Elmer Optima 3000 DV ICP system was used both with lateral and axial viewing modes. A laboratory-made ablation system based on the Brilliant laser (Quantel) was coupled to a Jobin-Yvon 170 Ultrace ICP (lateral viewing, polychromator part employed). A sample was rotated along a circle during ablation. Linearity of calibration plots was verified at least up to 19% Cr and 12% Ni without internal standardization for both LA–ICP–AES systems. Other elements examined were Mo up to 3%, Mn up 1.5%, Si up to 1.7%, and Cu up to 0.15%. The reproducibility was in the range 5–1 %RSD for a mass percentage 0.5–20% of steel constituents. The relative uncertainty of the centroids of the calibration lines was in the range from ± 4% to ± 12% for Cr, Ni, Mn, Mo, and Si, and from ± 8% to ± 19% for Cu. The lowest determinable quantities were calculated for calibration dependencies. Performances of both the IR-LA–ICP–AES were comparable.     

Determination of vanadium in petroleum and petroleum products using atomic spectrometric techniques

Vanadium is recognized worldwide as the most abundant metallic constituent in petroleum. It is causing undesired side effects in the refining process, and corrosion in oil-fired power plants. Consequently, it is the most widely determined metal in petroleum and its derivatives. This paper offers a critical review of analytical methods based on atomic spectrometric techniques, particularly flame atomic absorption spectrometry (FAAS), electrothermal atomic absorption spectrometry (ET AAS), inductively coupled plasma optical emission spectrometry (ICP OES), inductively coupled plasma mass spectrometry (ICP-MS). In addition an overview is provided of the sample pretreatment and preparation procedures for vanadium determination in petroleum and petroleum products. Also included are the most recent studies about speciation and fractionation analysis using atomic spectrometric techniques.     

Development of a procedure for the multi-element determination of trace elements in wine by ICP–MS

An inductively coupled plasma mass spectrometric (ICP–MS) procedure has been developed for the determination of trace elements in wine. The procedure consists in simple 1+1 dilution of the wine and semi-quantitative analysis (without external calibration) using In as internal standard. Thirty-one elements at concentrations ranging from 0.1 mg mL^–1 to 0.5 ng mL^–1 can be determined by ICP–MS analysis with and without digestion. It was investigated whether a matrix effect observed for EtOH in the wine matrix can be overcome by application of a micro-concentric nebulizer with a membrane desolvator (MCN 6000). The results obtained for the MCN 6000 are compared with those obtained by use of a conventional Meinhard nebulizer. It is shown that the observed matrix effect can only be compensated by use of an internal standard for the Meinhard nebulizer, but not for the MCN 6000. Results for ICP–MS are compared with those obtained by total reflection X-ray fluorescence spectrometry (TXRF).     

Mass spectrometry of natural organic phosphorus

This article provides a review of the use of modern mass spectrometry (MS) for quantitative and qualitative measurements of organic phosphorus compounds in nature. Included is a brief discussion of recent developments in large molecule mass spectrometry, focusing on time-of-flight (TOF) and ion cyclotron resonance (ICR) mass analysis techniques, as well as electrospray (ESI) and inductively coupled plasma (ICP) ionization. The use of ICP with high-resolution mass spectrometry for quantitative measurements of total phosphorus and as a detector coupled to HPLC and CE for defining organic phosphorus speciation is demonstrated using results from a study of phosphorus cycling in a treatment wetland. Qualitative identifications of individual phosphorus compounds by ultrahigh resolution Fourier-transform ion cyclotron resonance mass spectrometry (FT-ICR MS) is demonstrated using dissolved organic phosphorus isolated from this same wetland.     

Speciation of Arsenic Compounds in the Urine of Rats Orally Exposed to Dimethylarsinic Acid Ion Chromatography with ICP–MS as an Element-Selective Detector

A combined ion chromatography (IC) with inductively coupled plasma mass spectrometry (ICP—MS) system as an element-selective detector has been used for the determination of arsenic compounds. Seven arsenic compounds were separated by cation-exchange chromatography. Subsequently, the separated arsenic compounds were directly introduced into the ICP—MS and were detected at m/z =75. Detection limits for the seven arsenic compounds ranged from 0.8 to 3.8 μg As/l. The IC–ICP–MS system was applied to the determination of arsenic compounds in the urine of dimethylarsinic acid (DMAA)-exposed rats. DMAA was the most abundant arsenic compound detected. Arsenous acid, monomethylarsonic acid and trimethylarsine oxide were also detected.