Surface properties of cubic boron nitride thin films

Studying the surface properties of cubic boron nitride (c-BN) thin films is very important to making it clear that its formation mechanism and application. In this paper, c-BN thin films were deposited on Si substrates by radio frequency sputter. The influence of working gas pressure on the formation of cBN thin film was studied. The surface of c-BN films was analyzed by X-ray photoelectron spectroscopy (XPS), and the results showed that the surface of c-BN thin films contained C and O elements besides B and N. Value of N/B of c-BN thin films that contained cubic phase of boron nitride was very close to 1. The calculation based on XPS showed that the thickness of hexagonal boron nitride (h-BN) on the surface of c-BN films is approximately 0.8 nm.     

The electrical properties of sulfur-implanted cubic boron nitride thin films

Cubic boron nitride (c-BN) thin films are deposited on p-type Si wafers using radio frequency (RF) sputtering and then doped by implanting S ions. The implantation energy of the ions is 19 keV, and the implantation dose is between 10 15 ions/cm 2 and 10 16 ions/cm 2 . The doped c-BN thin films are then annealed at a temperature between 400°C and 800 C. The results show that the surface resistivity of doped and annealed c-BN thin films is lowered by two to three orders, and the activation energy of c-BN thin films is 0.18 eV.     

Upper critical field of niobium nitride thin films

The temperature dependences of the superconducting transition of niobium nitride (NbN) thin films have been investigated via the first harmonic of the voltage in dc magnetic fields of up to 8 T. The temperature dependence of the second critical field of NbN has been determined. The parameter responsible for the effect of spin paramagnetism in this material and the temperature dependence of the upper critical field that describes well the experimental data have been found in terms of the Werthamer–Helfand–Hohenberg (WHH) theory. The key parameters of the superconductor have been estimated from the transport and optical measurements.     

Influence of oxygen on the growth of cubic boron nitride thin films by plasma-enhanced chemical vapour deposition

Cubic boron nitride thin films were deposited on silicon substrates by low-pressure inductively coupled plasma-enhanced chemical vapour deposition. It was found that the introduction of O₂ into the deposition system suppresses both nucleation and growth of cubic boron nitride. At a B₂H₆ concentration of 2.5\% during film deposition, the critical O₂ concentration allowed for the nucleation of cubic boron nitride was found to be less than 1.4\%, while that for the growth of cubic boron nitride was higher than 2.1\%. Moreover, the infrared absorption peak observed at around 1230--1280~cm^-1, frequently detected for cubic boron nitride films prepared using non-ultrahigh vacuum systems, appears to be due to the absorption of boron oxide, a contaminant formed as a result of the oxygen impurity. Therefore, the existence of trace oxygen contamination in boron nitride films can be evaluated qualitatively by this infrared absorption peak.     

高质量宽带隙立方氮化硼薄膜的研究进展

文章着重介绍了最近研制出的高质量宽带隙立方氮化硼薄膜的三种制备方法和结构特性 :(1)用射频溅射法在Si衬底上制备出立方相含量在 90 %以上 ,Eg>6 .0eV的c-BN薄膜 ;(2 )用离子束辅助的化学气相沉积法(CVD) ,在金刚石上外延生长出立方含量达 10 0 %的单晶c -BN薄膜 ;(3)用微波电子回旋共振CVD法 (MW -ECR-CVD)在金刚石上外延生长出高纯c-BN薄膜 .这些高纯c -BN薄膜 ,可应用于制作各种半导体 (主要是高温、高频大功率 )电子器件 .     

碳、碳氮和硼碳氮纳米管场发射性能的比较研究

采用高温热解法在860℃分别制备出了碳、碳氮和硼碳氮纳米管，提纯后利用丝网印刷工艺分别将它们制备成薄膜，并测试了它们的场发射性能.结果表明：碳纳米管、碳氮纳米管和硼碳氮纳米管薄膜的开启电场分别为2.22，1.1和4.4V/μm，当电场增加到5.7V/μm时，它们的电流密度分别达到1400，3000μA/cm²和小于50μA/cm².碳和碳氮纳米管薄膜的场增强因子分别为10062和11521.可见，碳氮纳米管的场发射性能优于碳纳米管，而硼碳氮纳米管的场发射性能比前两者要差.解释了这三种纳米管场发射性能差别的原因. 关键词： 碳纳米管 碳氮纳米管 硼碳氮纳米管 场发射     

立方氮化硼薄膜沉积过程的相变研究

从能量和结构两个角度分析了BN四种相的转变过程，以及杂质和缺陷对立方氮化硼(c-BN)薄膜制备的影响.研究了从六角氮化硼(h-BN)到c-BN转变的一个可能的过程，即h-BN→菱形氮化硼(r-BN)→c-BN过程.对纯的h-BN到r-BN的转变需要克服一个很高的能量势垒，在实验室条件下很难能够提供能量来越过这个势垒.而从r-BN到c-BN的转变只需要克服一个很低的能量势垒.这个能量势垒要低于从h-BN到纤锌矿氮化硼(w-BN)转变所需要克服的能量势垒.c-BN薄膜的制备过程中，薄膜在高能粒子轰击下，会产生大量的缺陷，这些缺陷对立方相的形成起到了重要的作用，缺陷和杂质的存在大大降低了从h-BN到r-BN转变的能量势垒.根据这个理论模型，在两步法制备c-BN薄膜的基础上，调整实验参数，形成三步法制备高质量c-BN薄膜.主要研究了三步法中第一步的时间和衬底负偏压对c-BN薄膜制备的影响，找到合适的沉积时间和衬底负偏压分别为5min和-180V.采用三步法制备薄膜，可以重复得到高立方相体积分数(立方相体积分数超过80%)的BN薄膜，并且实验重复性达到70%以上. 关键词： 立方氮化硼 能量势垒 缺陷 衬底偏压     

Preparation of boron carbon nitride thin films by radio frequency magnetron sputtering

Boron carbon nitride films were deposited by radio frequency magnetron sputtering using a composite target consisting of h-BN and graphite in an Ar-N₂ gas mixture. The samples were characterized by X-ray diffraction, Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy. The results suggest that the films are atomic-level hybrids composed of B, C and N atoms. The boron carbon nitride films prepared in the present experiment have a disordered structure. The sputtering power varied from 80 W to 130 W. This sputtering power was shown to have regular effect on the composition of boron carbon nitride films. The samples deposited at 80 W and 130 W are close to the stoichiometry of BC₃N. The sample deposited at 110 W is close to the stoichiometry of BCN. The samples deposited at 100 W and 120 W approach to BC₂N. It is very significant for us to synthesize boron carbon nitride compound with controllable composition by changing the sputtering power.     

立方氮化硼薄膜的光学带隙

用射频溅射法在p型Si(100)衬底上沉积立方氮化硼(c-BN)薄膜,薄膜的成分由傅里叶变换红外谱标识,用紫外-可见分光光度计测量了c-BN薄膜的反射光谱,利用K-K(Kramers-Kroning)关系从反射谱计算出c-BN薄膜的光吸收系数,进而确定c-BN薄膜的光学带隙.对于立方相含量为55.4%的c-BN薄膜,光学带隙为5.38eV. 关键词： 立方氮化硼薄膜 光学带隙 K-K关系     

Specific field emission properties of thin palladium films

The field emission current from thin palladium films deposited on insulating tips in UHV was measured as a function of film thickness at relatively low field strengths. The observed periodic oscillations of the field emission current can be interpreted as the quantum size effect.     

Influence of oxygen plasma treatment on boron carbon nitride film composition

Variations in the composition and bonds of boron carbon nitride (BCN) film caused due to an oxygen (O₂) plasma ashing process are investigated for a low dielectric constant (low-k) insulating film for next generation LSI devices. The O₂ plasma treatment is preformed for BCN samples with various C compositions. The etching rate of BCN films with an O₂ plasma decreases with increasing C composition. The reaction of O atoms is suppressed in the BCN film with a high C composition. B-N and B-C bonds with lower bond energies are easily broken by the O₂ plasma and replaced by the generation of B-O, N-O, and C-O bonds. The B-atom concentration for all samples is decreased significantly by the O₂ plasma treatment. Ion bombardment may play a more dominant role than the O-atom reaction in the etching of the BCN film. The existence of C-N bonds with a high bonding energy may suppress etching and incorporation of O atoms.     

Influence of heat treatment on the electrophysical properties of thin films of copper-indium diselenide

An investigation of the structural, electrical, optical, and thermophysical properties is carried out on thin polycrystalline films of the ternary semiconductor CuInSe₂, which is potentially useful for fabricating solar cells. The thin films were obtained by thermal evaporation of CuInSe₂ and Se powder from two independent sources and by high-vacuum deposition in a closed cell (quasiequilibrium deposition). The influence of annealing in air on the parameters of the thin films is analyzed, and the dynamics of variation in the properties of the films are investigated as a function of the annealing time. Temperature dependences of the electrical conductivity, mobility, and thermal conductivity of CuInSe₂ thin films are given together with the spectral dependence of the short-circuit photocurrent of a photosensitive Au-CuInSe₂-Au structure. Zh. Tekh. Fiz. 67, 34–38 (March 1997)     

硼对沉积本征微晶硅薄膜特性的影响

采用甚高频等离子体增强化学气相沉积(VHF-PECVD)技术制备了不同腔室环境下的微晶硅薄膜.对单室沉积掺杂层p材料后遗留在腔室中的硼对本征微晶i材料电学特性和结构特性的影响进行了详细研究.测试结果表明：单室沉积p层后的硼降低了微晶i层材料的暗电导,增加了材料的光敏性;由于硼对i层污染程度的不同,使得材料的激活能发生了变化;腔室中残余的硼也导致微晶硅薄膜的结晶状况恶化,同时弱化了材料的(220)择优取向.而在较高功率和较强氢稀释下制备的晶化率较高,(220)晶向明显择优的材料受硼污染影响相对减小. 关键词： 单室 甚高频等离子体增强化学气相沉积 微晶硅 硼     

Effects of experimental parameters on composition of boron carbon nitride thin films deposited by magnetron sputtering

We have synthesized boron carbon nitride thin films by radio frequency magnetron sputtering. The films structure and composition were characterized by X-ray diffraction, Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy. The results indicate that the three elements of B, C, N are chemically bonded with each other and atomic-level hybrids have been formed in the films. The boron carbon nitride films prepared in the present experiment possess a disordered structure. The influence of PN₂/PN₂+Ar, total pressure and substrate bias voltage on the composition of boron carbon nitride films is investigated. The atomic fraction of C atoms increases and the fractions of B, N decrease with the decrease of PN₂/PN₂+Ar from 75% to 0%. There is an optimum total pressure. That is to say, the atomic fractions of B, N reach a maximum and the fraction of C atoms reaches a minimum at the total pressure of 1.3 Pa. The boron carbon nitride films exhibit lower C content and higher B, N contents at lower bias voltages. And the boron carbon nitride films show higher C content and lower B, N contents at higher bias voltages.     

Deposition of hexagonal boron nitride thin films on silver nanoparticle substrates and surface enhanced infrared absorption

Silver nanoparticle thin films with different average particle diameters are grown on silicon substrates. Boron nitride thin films are then deposited on the silver nanoparticle interlayers by radio frequency （RF） magnetron sputtering. The boron nitride thin films are characterized by Fourier transform infrared spectra. The average particle diameters of silver nanoparticle thin films are 126.6, 78.4, and 178.8 nm. The results show that the sizes of the silver nanoparticles have effects on the intensities of infrared spectra of boron nitride thin films. An enhanced infrared absorption is detected for boron nitride thin film grown on silver nanoparticle thin film. This result is helpful to study the growth mechanism of boron nitride thin film.     

Correlation between density and structure. in boron nitride thin films by X-ray diffraction

* _ion=100 eV. Above E^* _ion the average density (deduced from X-ray reflectivity) shows a strong increase, indicating the sudden appearance of the cubic boron nitride phase consistent with the sp³ concentration deduced from IR absorption spectroscopy. The in-plane X-ray diffraction shows that this cubic phase consists of small nanocrystals of 70 Å linear size. Received: 26 November 1996/Accepted: 27 January 1997     

Enhanced field emission characteristics of boron doped diamond films grown by microwave plasma assisted chemical vapor deposition

Boron doped diamond films were synthesized on silicon substrates by microwave plasma chemical vapor deposition (MPCVD) technique. The effect of B₂O₃ concentration varied from 1000 to 5000 ppm on the field emission characteristics was examined. The surface morphology and quality of films were characterized by scanning electron microscope (SEM) and Raman spectroscopy. The surface morphology obtained by SEM showed variation from facetted microcrystal covered with nanometric grains to cauliflower of nanocrystalline diamond (NCD) particles with increasing B₂O₃ concentration. The Raman spectra confirm the formation of NCD films. The field emission properties of NCD films were observed to improve upon increasing boron concentration. The values of the onset field and threshold field are observed to be as low as 0.36 and 0.08 V/μm, respectively. The field emission current stability investigated at the preset value of ∼1 μA is observed to be good, in each case. The enhanced field emission properties are attributed to the better electrical conductivity coupled with the nanometric features of the diamond films.     

薄膜场发射开启电场的小波神经网络预测模型研究

关键词：     

等离子体增强化学气相沉积法制备立方氮化硼薄膜过程中的表面生长机理

利用感应耦合等离子体增强化学气相沉积法以Ar，He，N₂和B₂H₆为反应气体制备了高纯立方氮化硼薄膜.用四极质谱仪对等离子体状况进行了系统的分析，发现B₂H₆完全被电离而N₂只是部分被电离.H₂和过量的N₂在等离子体中生成大量中性的H原子和活化的N^*₂，它们与表面的相互作用严重地阻碍了立方 关键词： 立方氮化硼薄膜 等离子体 质谱