水泥砂浆界面相弹性常数的反演计算

为了计算水泥砂浆界面过渡区的弹性常数,采用广义自洽方法(GSCM),根据水泥砂浆内部的微细观结构,建立了由水泥浆基体、岩石离散夹杂(骨料)、界面过渡区(ITZ)和有效弹性材料组成的四相复合材料模型.推导了界面相的体积模量和剪切模量方程.利用已知水泥砂浆材料的实验数据,计算了界面相的弹性常数.发现界面相剪切模量约为水泥浆基体剪切模量的50%.     

Nonlinear behavior of matrix-inclusion composites under high confining pressure: application to concrete and mortar

This paper is devoted to a micromechanics-based simulation of the response of concrete to hydrostatic and oedometric compressions. Concrete is described as a composite made up of a cement matrix in which rigid inclusions are embedded. The focus is put on the role of the interface between matrix and inclusion which represent the interfacial transition zone (ITZ). A plastic behavior is considered for both the matrix and the interfaces. The effective response of the composite is derived from the modified secant method adapted to the situation of imperfect interfaces. To cite this article: T.H. Le et al., C. R. Mecanique 336 (2008).     

A material model for cementitious composite materials with an exterior point Eshelby microcrack initiation criterion

A micromechanical model for cementitious composite materials is described in which microcrack initiation, in the interfacial transition zone between aggregate particles and cement matrix, is governed by an exterior-point Eshelby solution. The model assumes a two-phase elastic composite, derived from an Eshelby solution and the Mori–Tanaka homogenization method, to which circular microcracks are added. A multi-component rough crack contact model is employed to simulate normal and shear behaviour of rough microcrack surfaces. The development of the microcrack initiation criterion and the rules adopted for microcrack evolution are a particular focus of the paper. Finally, it is shown, on the basis of several numerical simulations, that the model captures key characteristics of the behaviour of cementitious composites such as concrete.     

Modelling of compressive behaviour of concrete-like materials at high strain rate

Uniaxial compression tests are the most common tests for characterizing the strength of concrete-like materials. The dynamic compression strength of concrete-like material is typically obtained by Split Hopkinson Pressure Bar (SHPB) tests. The increase in material strength under dynamic loading is usually attributed to the strain rate effect and modelled with a dynamic increase factor (DIF). However, it was observed by some researchers that the radial inertial confinement caused apparent increase of dynamic strength of concrete-like specimen in SHPB tests. They attributed the material strength increase to this inertial effect, instead of the strain rate effect. In the present study, numerical analyses are performed to investigate the compressive behaviour of concrete-like material at high strain rates. A homogeneous macroscale model and a heterogeneous mesoscale model are developed in the study. In the macroscale model, the material is assumed to be homogeneous and isotropic. In the mesoscale model, the test sample is modelled as a three-phase composite consisting of aggregate, mortar matrix and interfacial transaction zone (ITZ) between the aggregate and the mortar matrix. The aggregate is assumed to be circular and the ITZ is modelled as a thin boundary around the aggregate. In the both models, the materials are assumed to be insensitive to the strain rate first. Therefore, the obtained strength enhancement is only due to the inertial confinement. Strain rate sensitive material properties are then used in the two models in the calculations. Numerical simulations of the concrete samples under compression at different strain rates are carried out. The relative contribution of the inertial effect and the strain rate effect on the compressive strength DIF is examined based on the numerical results. The failure process of concrete specimen is also studied.     

一种预测颗粒增强复合材料界面力学性能的新方法

界面在颗粒增强复合材料中起到传递载荷的关键作用,界面性能对复合材料整体力学行为产生重要影响.然而由于复合材料内部结构较为复杂,颗粒与基体间的界面强度和界面断裂韧性难以确定,尤其是法向与切向界面强度的分别预测缺乏有效方法.本文以氧化锆颗粒增强聚二甲基硅氧烷(PDMS)复合材料为研究对象,提出一种预测颗粒增强复合材料界面力...     

A micromechanical study of drying and carbonation effects in cement-based materials

This paper is devoted to a micromechanical study of mechanical properties of cement-based materials by taking into account effects of water saturation degree and carbonation process. To this end, the cement-based materials are considered as a composite material constituted with a cement matrix and aggregates (inclusions). Further, the cement matrix is seen as a porous medium with a solid phase (CSH) and pores. Using a two-step homogenization procedure, a closed-form micromechanical model is first formulated to describe the basic mechanical behavior of materials. This model is then extended to partially saturated materials in order to account for the effects of water saturation degree on the mechanical properties. Finally, considering the solid phase change and porosity variation related to the carbonation process, the micromechanical model is coupled with the chemical reaction and is able to describe the consequences of carbonation on the macroscopic mechanical properties of material. Some comparisons between numerical results and experimental data are presented.     

Micromechanical approach to the strength properties of frictional geomaterials

The present paper describes a micromechanics-based approach to the strength properties of composite materials with a Drucker–Prager matrix in the situation of non-associated plasticity. The concept of limit stress states for such materials is first extended to the context of homogenization. It is shown that the macroscopic limit stress states can theoretically be obtained from the solution to a sequence of viscoplastic problems stated on the representative elementary volume. The strategy of resolution implements a non-linear homogenization technique based on the modified secant method. This procedure is applied to the determination of the macroscopic strength properties and plastic flow rule of materials reinforced by rigid inclusions, as well as for porous media. The role of the matrix dilatancy coefficient is in particular discussed in both cases. Finally, finite element solutions are derived for a porous medium and compared to the micromechanical predictions.     

纤维复合材料界面横向拉伸分析

以单纤维十字型横向拉伸试验为研究对象,对纤维/基体界面采用弹性-软化双线性内聚力模型,建立了纤维复合材料在横向拉伸作用下界面法向失效过程的解析模型。得到了沿纤维/基体圆周界面的法向应力分布,纤维/基体界面的状态与界面承载力和单纤维复合材料承载力的关系,以及内聚力参数和试件几何尺寸对它们的影响。结果表明:纤维/基体圆周界面在脱粘前经历全部弹性及弹性+软化两种状态;当界面为弹性状态时,界面法向应力随界面强度线性增加;当界面为弹性+软化状态时,界面软化范围随界面裂纹萌生位移的增加而增大;界面初始脱粘位置与拉伸荷载方向重合;界面初始脱粘时的界面承载力随界面强度及界面裂纹萌生位移的增加而增加,随界面裂纹生成位移的增加而降低;单纤维复合材料的脱粘荷载受基体截面尺寸的影响,当纤维体积含量相同时,沿荷载方向截面尺寸的增大对提高脱粘荷载更显著。     

混凝土微观界面纳米划痕试验表征研究

鉴于混凝土微观结构对宏观性能的重要影响,利用纳米划痕试验方法,对常规水灰比配比的混凝土样品骨料-水泥浆体微观界面及界面过渡区进行了表征研究．基于纳米划痕试验方法和扫描电镜显微技术,对于样品微观情况下的骨料-水泥浆体界面进行了表征分析,并对表征结果经过多个高斯分布拟合的统计学分析方法得到基于界面位置的结构划痕硬度分布情况．通过划痕硬度与骨料-浆体界面的距离变化,定义了骨料和水泥浆体之间的界面过渡区,并得到界面过渡区厚度约为40μm,界面过渡区划痕硬度约为水泥浆料硬度的75％左右．通过比较划痕断裂韧性与宏观试验结果,证明利用纳米划痕试验可以初步分析材料断裂韧性．本研究为更好地研究混凝土微观性能对宏观力学性能的影响提供了可靠的数据支持,也为评价混凝土微观界面力学性能提供了一种新的可行方法．     

Multiscale lattice Boltzmann-finite element modelling of chloride diffusivity in cementitious materials. Part II: Simulation results and validation

Chloride diffusivity in cementitious materials depends on the underlying microstructure and environmental conditions. The algorithms and implementation of the multiscale lattice Boltzmann-finite element scheme for prediction of chloride diffusivity in cementitious materials was described in detail in Part I (Zhang et al., 2013). Based on the obtained microstructures and the developed multiscale modelling scheme, chloride diffusivity in cementitious materials at the micro- and meso-scales, i.e. cement paste, mortar and concrete, are estimated and presented in Part II. The influences of w/c ratio, age, chloride binding, degree of water saturation, interfacial transition zone (ITZ) and aggregate content on chloride diffusivity are investigated in a quantitative manner. The simulations are validated with experimental data obtained from literature. The results indicate that the simulated chloride diffusivity in cementitious materials at each scale shows a good agreement with experimental data. In addition, the chloride binding, degree of water saturation, ITZ and aggregate content play significant roles in the chloride diffusivity in cementitious materials. The estimated chloride diffusivity in cementitious materials in this study accounting for the evolution of microstructure and environmental conditions can be directly used as input for the service life prediction of reinforced concrete structures.     

Fiber push-out study of a copper matrix composite with an engineered interface: Experiments and cohesive element simulation

The fiber push-out test is a basic method to probe the mechanical properties of the fiber/matrix interface of fiber-reinforced metal matrix composites. In order to estimate the interfacial properties, parameters should be calibrated using the measured load–displacement data and theoretical models. In the case of a soft matrix composite, the possible plastic yield of the matrix has to be considered for the calibration. Since the conventional shear lag models are based on elastic behavior, a detailed assessment of the plastic effect is needed for accurate calibration. In this paper, experimental and simulation studies are presented regarding the effect of matrix plasticity on the push-out behavior of a copper matrix composite with strong interface bonding. Microscopic images exhibited significant local plastic deformation near the fibers leading to salient nonlinear response in the global load–displacement curve. For comparison, uncoated interface with no chemical bonding was also examined where the nonlinearity was not observed. A progressive FEM simulation was conducted for a complete push-out process using the cohesive zone model and inverse fitting. Excellent coincidence was achieved with the measured push-out curve. The predicted results confirmed the experimental observations.     

钢筋锈胀引发混凝土保护层开裂破坏的细观数值研究

钢筋锈蚀膨胀引起保护层混凝土开裂是影响钢筋混凝土结构耐久性和服役寿命的重要因素。考虑到混凝土细观结构组成对保护层破坏模式的影响,从细观角度出发,将混凝土看作由骨料、砂浆基质及两者间界面过渡区组成的三相复合材料,建立了描述钢筋锈胀力学行为的混凝土随机骨料模型。采用塑性损伤本构关系模型来表征砂浆基质和过渡区界面的力学行为,假定钢筋均匀锈蚀,对钢筋锈胀引起的混凝土保护层开裂破坏过程进行了细观数值研究。对比了宏观均匀模型与细观非均质模型下获得的保护层破坏模式,探讨了径厚比(c/d)、钢筋位置(中部和角区)及混凝土拉伸强度对保护层破坏模式及保护层胀裂时钢筋锈蚀水平的影响,得到了一些有益结论。     

Homogenization of two-phase elasto-plastic composite materials and structures: Study of tangent operators,cyclic plasticity and numerical algorithms

We develop homogenization schemes and numerical algorithms for two-phase elasto-plastic composite materials and structures. A Hill-type incremental formulation enables the simulation of unloading and cyclic loadings. It also allows to handle any rate-independent model for each phase. We study the crucial issue of tangent operators: elasto-plastic (or “continuum”) versus algorithmic (or “consistent”), and anisotropic versus isotropic. We apply two methods of extraction of isotropic tangent moduli. We compare mathematically the stiffnesses of various tangent operators. All rate equations are discretized in time using implicit integration. We implemented two homogenization schemes: Mori–Tanaka and a double inclusion model, and two plasticity models: classical J₂ plasticity and Chaboche’s model with non-linear kinematic and isotropic hardenings. We consider composites with different properties and present several discriminating numerical simulations. In many cases, the results are validated against finite element (FE) or experimental data. We integrated our homogenization code into the FE program ABAQUS using a user material interface UMAT. A two-scale procedure allows to compute realistic structures made of non-linear composite materials within reasonable CPU time and memory usage; examples are shown.     

固化温度对碳纤维/环氧基体界面行为影响的分析

对界面粘结性能及热残余应力影响下的单纤维复合材料的界面行为进行了分析。采用界面的弹性-软化内聚力模型,用解析法对单纤维复合材料由固化引起的热残余应力、以及单纤维碎断过程纤维的轴向应力分布进行了模拟,得到了碳纤维/环氧树脂在常温和高温固化两种情况的界面粘结性能。结果表明：与常温固化相比,高温固化后,界面的剪切强度增幅不大,界面的断裂韧性显著增加;高温固化后形成的界面,使界面的软化提前、界面的脱粘延迟;高温固化产生的纤维轴向和界面径向热残余应力对界面的软化均有延迟作用;界面径向热残余应力还对界面的脱粘有延迟作用。     

Bifurcation phenomena in the rigid inclusion power law matrix composite sphere

Bifurcation of interface separation related to cavity nucleation is analyzed for a radially loaded composite sphere consisting of a rigid inclusion separated from a power law matrix by a uniform, non-linear cohesive zone. Equations for the spherically symmetric and non-symmetric problems are obtained from a hyperelastic finite strain theory by a limiting process that preserves non-linear matrix and interface response at infinitesimal strain. A complete solution to the symmetric problem is presented including bifurcation load, stresses, and evolution of elasto-plastic boundary and interface separation. An analysis of non-symmetric bifurcation, under symmetric conditions of geometry and loading, yields the bifurcation load and first non-symmetric mode shape associated with rigid inclusion displacement. An energy analysis is carried out for both symmetric and non-symmetric problems in order to assess stability of spherically symmetric states to spherically symmetric and non-symmetric “rigid body mode” perturbations.Results are provided for an interface force law that captures interface failure in normal mode and linear response in shear mode. For the symmetric problem, (i) there are threshold parameter values above which bifurcation will generally not occur, (ii) threshold values below which there do not exist equilibria in the post bifurcation regime, (iii) bifurcation occurs after attainment of the maximum interface strength. For the non-symmetric problem, (i) bifurcation always occurs, although it can be delayed by interfacial shear, (ii) for the smooth interface, non-symmetric bifurcation occurs after attainment of the maximum interface strength and always precedes symmetric bifurcation.     

金属基纳米复合材料等效弹性模量的均匀化方法数值模拟

均匀化理论利用位移场双尺度渐近展开建立有限元列式，本文将其与有限元通用程序相结合，应用于金属基复合材料的弹性本构数值模拟。通过对不同尺度增强相金属基复合材料等效模量的数值模拟，考察了均匀化方法的适用情况。数值计算结果表明，对常规尺度增强相金属基复合材料，均匀化方法可以较准确地预测其等效弹性模量；对纳米增强相金属基复合材料，该方法仍可给出较好的预测，但存在某种程度的系统偏差。通过对纳米尺度增强机理的分析讨论，认为纳米增强相与基体材料问的界面效应可能有别于连续介质假设，指出可以考虑采用离散原子-连续介质耦合模型改进数值模拟结果。     

温度循环载荷对柔性接头界面损伤的影响

固体火箭发动机在生产、运输和储存的过程中会受到环境湿热和老化载荷的作用,导致柔性接头界面的力学性能产生退化.为研究柔性接头界面力学性能退化对界面损伤的影响规律,基于双线性内聚力模型建立了一种描述界面力学性能退化的数学模型.以某柔性接头为研究对象,为便于研究,以温度循环载荷代替环境老化载荷开展了界面损伤分析,并采用ABA...     

Residual strength of a fiber reinforced metal matrix composite with a crack

The residual strength of a cracked unidirectional fiver reinforced metal matrix composite is studied. We propose a bridging model based on the Dugdale strip yielding zones in the matrix ahead of the crack tips that accounts for ductile deformations of the matrix and fiber debonding and pull-out in the strip yielding zone. The bridging model is used to study the fracture of an anisotropic material and its residual strength is calculated numerically. The predicted results for a SiC/titanium composite agree well with the existing experimental data. It is found that a higher fiber bridging stress and a larger fiber pull-out length significantly contribute to the composite's residual strength. The composite's strength may be more notch-insensitive than the corresponding matrix material's strength depending on several factors such as fiber-matrix interface properties and the ratio of the matrix modulus to an ‘effective modulus’ of the composite.     

Micromechanical modelling of dry and saturated cement paste: Porosity assessment using ultrasonic waves

This article assesses the relationship between porosity and ultrasonic parameters of cement paste. It includes theoretical assessment of ultrasonic wave velocities of cement paste materials. Theoretical micromechanical models describing cement paste as a two-phase composite were detailed. Mechanical (bulk and shear moduli) and ultrasonic (longitudinal and transverse velocities) properties were evaluated. They were then, compared to the experimental ultrasonic properties measured on dry and fully water saturated samples with varying porosity First, the obtained micromechanical results showed that the correlation between acoustic velocity and porosity yielded the expected values: longitudinal and transverse velocities decrease with porosity. Secondly, the dilute inclusion model was able to represent the acoustic parameter of the cement paste only at low porosity, up to 20%. The self-consistent model under-estimated the measured ultrasonic properties for almost all porosity ranges. The Mori–Tanaka and the Kuster–Toksöz models succeeded in describing the acoustic parameters in dry and saturated states when assuming spherical shaped pores.     

Micromechanical analysis of polymer composites reinforced by unidirectional fibres: Part I – Constitutive modelling

Micromechanical analyses of unidirectional continuous-fibre reinforced composite materials were performed to study the mechanisms of deformation and fracture of the constituents, and their influence on the mechanical properties of the composite. Special focus was given to the matrix material behaviour as well as to the interface between constituents. The matrix was modelled using a pressure dependent, elasto-plastic thermodynamically consistent damage model. Cohesive elements were used to model the interface between matrix and fibres. Part I of this paper details the continuum model developed for a typical epoxy matrix. Part II will focus on micromechanical analyses of composite materials and the estimation of its elastic and strength properties.