Structural and optical properties of Co-doped ZnO nanocrystallites prepared by a one-step solution route

Zinc oxide (ZnO) nanocrystallites with different Co-doping levels were successfully synthesized by a simple one-step solution route at low temperature (95 °C) in this study. The structure and morphology of the samples thus obtained were characterized by XRD, EDS, XPS and FESEM. Results show that cobalt ions, in the oxidation state of Co²⁺, replace Zn²⁺ ions in the ZnO lattice without changing its wurtzite structure. The dopant content varies from 0.59% to 5.39%, based on Co-doping levels. The pure ZnO particles exhibit well-defined 3D flower-like morphology with an average size of 550 nm, while the particles obtained after Co-doping are mostly cauliflower-like nanoclusters with an average size of 120 nm. Both the flower-like pure ZnO and the cauliflower-like Co:ZnO nanoclusters are composed of densely arrayed nanorods. The optical properties of the ZnO nanocrystallites following Co-doping were also investigated by UV–Visible absorption and Photoluminescence spectra. Our results indicate that Co-doping can change the energy-band structure and effectively adjust the luminescence properties of ZnO nanocrystallites.     

Quantum dots of Cd0.5Mn0.5Te semimagnetic semiconductor formed by the cold isostatic pressure method

Cd_0.5Mn_0.5Te is a semimagnetic semiconductor, which crystallizes in the zinc-blende structure (ZB) and exhibits a magnetic spin glass like transition at 21 K. Under pressure it shows a first-order phase transition around 2.6 GPa to the NaCl like structure. In this work, the pressure cycled method using a Paris–Edinburgh cell up to 8 GPa has been applied to Cd_0.5Mn_0.5Te samples in order to obtain recovered nanocrystals. The nanoparticles have been characterized by EDX and electron microscopy. The X-ray and electron diffraction results confirmed the existence of nanocrystals in the ZB phase with an average size of 7 nm. Magnetization measurements made in the range of 2–300 K at low field show that the temperature of the magnetic transition decreases when the crystallites’ size is reduced.     

Structural and photoluminescence investigation on the hot-wire assisted plasma enhanced chemical vapor deposition growth silicon nanowires

High density of silicon nanowires (SiNWs) were synthesized by a hot-wire assisted plasma enhanced chemical vapor deposition technique. The structural and optical properties of the as-grown SiNWs prepared at different rf power of 40 and 80 W were analyzed in this study. The SiNWs prepared at rf power of 40 W exhibited highly crystalline structure with a high crystal volume fraction, X_C of ～82% and are surrounded by a thin layer of SiO_x. The NWs show high absorption in the high energy region (E>1.8 eV) and strong photoluminescence at 1.73 to 2.05 eV (red–orange region) with a weak shoulder at 1.65 to 1.73 eV (near IR region). An increase in rf power to 80 W reduced the X_C to ～65% and led to the formation of nanocrystalline Si structures with a crystallite size of <4 nm within the SiNWs. These NWs are covered by a mixture of uncatalyzed amorphous Si layer. The SiNWs prepared at 80 W exhibited a high optical absorption ability above 99% in the broadband range between 220 and ～1500 nm and red emission between 1.65 and 1.95 eV. The interesting light absorption and photoluminescence properties from both SiNWs are discussed in the text.     

Morphology and optical properties of Mg and Sr doped CaF2 nanocrystals

Magnesium (Mg) and Strontium (Sr) doped Calcium fluoride nanocrystals were synthesized by co-precipitation method. The cubic structure of the samples was confirmed by Powder X-ray diffraction. The average crystallite size of Mg doped samples was found to be ~ 25 nm whereas in Sr doped one it was ~ 35 nm. The morphological features revealed that the nanocrystals were agglomerated, crispy and porous. The as-prepared samples showed the presence of hydroxyl groups. The optical absorption spectrum of as-prepared Mg doped samples showed a strong absorption band peaked at ~ 233 nm whereas the Sr doped one showed a prominent absorption peak at 248 nm. A strong PL emission was observed at ~ 300 nm in Mg doped samples. However, the Sr doped samples showed two prominent emissions at ~ 345 and 615 nm.     

Microstructures and nano mechanical properties of the metal tungsten film

The W film was prepared on 1045 steel by magnetron sputtering, with the thickness of 2 μm, its surface and cross-section morphologies were investigated with SEM, and the phase structure was analyzed with XRD. X-ray stress determinator was utilized to measure its residual stress, and the nano-hardness and elastic modulus of the film were surveyed by nano-indentation tester. The results show that the surface of W film is very compact and smooth; the particles arranged regularly, the granularity of the thin film is about 1 μm. The microcracks, cavities and desquamation were not found in the film and interface, and the bonding between the W film and substrate is well. The XRD results showed that the W film had a body-centered cubic structure, the lattice constant: a = 0.316 nm, the growth preferred orientations are (1 1 0) and (2 2 0). The compressive stress (−169 MPa) was found on the surface. The average nano-hardness and elastic modulus of W film are 15.22 GPa, 176.64 GPa, respectively, and the mechanical properties of W film are well.     

Optical temperature sensor through infrared excited blue upconversion emission in Tm3 +/Yb3 + codoped Y2O3

An analysis of the intense blue upconversion emission at 476 and 488 nm in Tm^3 +/Yb^3 + codoped Y₂O₃ under excitation power density of 86.7 W/cm² available from a diode laser emitting at 976 nm, has been undertaken. Fluorescence intensity ratio (FIR) variation of temperature-sensitive blue upconversion emission at 476 and 488 nm in this material was recorded in the temperature range from 303 to 753 K. The maximum sensitivity derived from the FIR technique of the blue upconversion emission is approximately 0.0035 K^? 1. The results imply that Tm^3 +/Yb^3 + codoped Y₂O₃ is a potential candidate for the optical temperature sensor.     

Structural origin of perpendicular magnetic anisotropy in Ni–W thin films

The magnetic properties and microstructure of electrodeposited Ni–W thin films (0–11.7 at% W in composition) were studied. The film structures were divided into three regions: an FCC nanocrystalline phase (0–2 at% W), a transition region from FCC nanocrystalline to amorphous phase (2–7 at% W), and an amorphous phase (>7 at% W). In the transition region, (4–5 at% W) films with perpendicular magnetic anisotropy (PMA) were found. The saturation magnetization, magnetic anisotropy field, perpendicular magnetic anisotropy and perpendicular coercivity for a typical Ni–W film (4.5 at% W) were 420 kA/m, 451 kA/m, 230 kJ/m and 113 kA/m, respectively. The microstructure of Ni–W films with PMA is composed of isolated columnar crystalline grains (27–36 nm) with the FCC phase surrounded by the Ni–W amorphous phase. The appearance of the interface between the magnetic core of Ni crystalline grains and the Ni–W non-magnetic boundary layer seems to be the driving mechanism for the appearance of PMA. The origin of PMA in Ni–W films is mainly attributed to the magnetoelastic anisotropy associated with in-plane internal stress and positive magnetostriction. The secondary source of PMA is believed to be the magnetocrystalline anisotropy of 〈1 1 1〉 columnar grains and its shape magnetic anisotropy. It is concluded that Ni–W electrodeposited films (4–5 at% W) may be applicable for perpendicular magnetic recording media.     

Highly efficient and stable organic light-emitting diode by balancing drift current of charge

Highly efficient and stable OLED device in which hole-drift current and electron-drift current are balanced was fabricated. Drift current characteristics according to the thickness of organic layer were examined using the device with ITO/m-MTDATA/NPB/Al structure that can only move the hole and the device with Al/LiF/Alq₃/LiF/Al structure that can only move the electron. Using the result of such examination, green device with balanced drift current was produced. Device with the structure of m-MTDATA (80 nm)/NPB (20 nm)/C-545T (3%) doped Alq₃ (5 nm)/Alq₃ (59 nm)/LiF (1 nm)/Al (200 nm) showed color purity of (0.309, 0.643) and high efficiency of 7.0 lm/W (14.4 cd/A). Most of light emission was observed inside the green emitting layer. Through the result of EL spectrum for the device also including red emitting layer, same result could be obtained. The device with balanced drift current also showed half life-time of 175 h for initial luminance of 3000 cd/m², which is more stable in comparison to the device without balanced drift current.     

Synthesis,characterization and photoluminescence of ZnO:Cd rosette-like nanostructures using solution process

Well crystalline undoped and Cd-doped ZnO rosette-like structures were successfully synthesized at low temperature (80 °C) via solution process technique during 30 min. Zinc nitrate, cadmium nitrate, sodium hydroxide and hexamine were used as starting materials. The morphology and microstructure were determined by field emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDX) and photoluminescence (PL) spectroscopy. X-ray diffraction indicated that the structure has a single phase with wurtzite structure. FESEM indicated that rosette like structures have been formed. This rosette consists of nanorods with length 210 and 460 nm and diameter 50 and 74 nm for undoped and Cd doped ZnO, respectively. HRTEM showed a decrease in the lattice parameter after the Cd doping. EDX showed that the amount of Cd incorporated into ZnO is 6.4 wt.%. Photoluminescence measurements taken on both doped and undoped samples showed that, in the Cd-doped ZnO nanostructures, the band-edge UV emission is blue shifted and the broad green emission intensity decreased.     

Influence of argon ambience on the structural,morphological and optical properties of pulsed laser ablated zinc sulfide thin films

Nanostructured zinc suplhide thin films are successfully deposited on quartz substrates using pulsed laser deposition (PLD) under different argon pressures (0, 5, 10, 15 and 20 Pa). The influence of argon ambience on the microstructural, optical and luminescence properties of zinc sulfide (ZnS) thin films is systematically investigated. The GIXRD data suggests rhombohedral structure for ZnS films prepared under different argon ambience. Self-assembly of grains into well-defined patterns along the y direction is observed in the AFM image of the film deposited under argon pressure 20 Pa. All the films show a blue shift in optical band gap. This can be due to the quantum confinement effect and less widening of conduction and valence band for the films with less thickness and smaller grain size. The PL spectra of the different films are recorded at excitation wavelengths 250 nm and 325 nm and the spectra are interpreted. The PL spectra of the films recorded at excitation wavelength 325 nm show intense yellow emission. The film deposited under an argon pressure of 15 Pa shows the highest PL intensity for excitation wavelength 325 nm. For the PL spectra (excitation at 250 nm), the highest PL intensity is observed for the film prepared under argon free ambience. In our study, 15 Pa is the optimum argon pressure for better crystallinity and intense yellow emission when excited at 325 nm.     

Electrodeposition of nickel-tungsten alloys under ultrasonic waves: Impact of ultrasound intensity on the anticorrosive properties

Electrodeposited Ni–W alloy assisted by high-intensity ultrasound was evaluated considering the nominal power effect on the anticorrosive property. Temperature profiles demonstrated that using a nominal power of 400 W, the electrolytic bath at 30 °C reached values of 39 ± 1 °C. The maximum acoustic power corresponded to 6.7% of the nominal power value at 400 W. Increasing the nominal power from 0 to 400 W; the Ni content decreased from 85.3 to 75.2 wt%, and the W content increased from 15.1 to 25.1 wt%. The deposited coating at 200 W and 300 W had a smooth, homogeneous, and uniform surface. At 400 W, the acoustic cavitation promoted erosion, affecting the coating surface. X-ray diffraction analysis indicated that the nominal power of 200 W promoted electrodeposition of the Ni₁₇W₃ structure with the plane (1 1 1) as a preferred orientation. The crystallite size decreased for the planes (1 1 1) and (2 0 0) when increased nominal power from 100 to 200 W. The optimum condition for the improved corrosion resistance occurred with the nominal power of 200 W, providing a polarization resistance of 23.42 kΩ cm².     

High resolution measurement and modelling of magnetic domain structures in epitaxial FePd (0 0 1) L10 films with perpendicular magnetisation

Magnetic domain structures in two 50 nm thick chemically-ordered FePd (0 0 1) epitaxial films with different perpendicular anisotropies have been studied using Lorentz microscopy. Domain and domain wall structures vary significantly according to the magnitude of the anisotropy. For lower anisotropy films, a stripe domain structure with a period of ≈100 nm is formed in which there is a near-continuous variation in orientation of the magnetisation vector. By contrast, in the film with higher anisotropy, a maze-like domain structure is supported. The magnetisation within domains is perpendicular to the film plane and adjacent domains are separated by narrow walls, less than 20 nm wide. Micromagnetic modelling is generally in good quantitative agreement with experimental observations and provides additional information on the domain wall structure.     

Terahertz emission dependence on the intensity ratio of 400–800 nm in generating terahertz waves from two-color laser-induced gas plasma

A transient photocurrent model is used to explain terahertz emission from gas plasma irradiated by a laser pulse and the second harmonic. By introducing the second harmonic, 400 nm, the corresponding terahertz emission is greatly enhanced. The exact dependence of terahertz emission on the intensity ratio of 400–800 nm is studied for the case with total intensity of 5.00 × 10¹⁴ W/cm². Results show the emission reaches the maximum at about the case for energy distribution of I_ω = 4.00 × 10¹⁴ W/cm², I_2ω = 1.00 × 10¹⁴ W/cm².     

Continuous-wave 560 nm light generated by intracavity SrWO4 Raman and KTP sum-frequency mixing

An LD end-pumped Nd:YAG/SrWO₄ continuous-wave 560 nm laser is presented based on intracavity sum-frequency mixing of the fundamental and first-Strokes light. The maximum output power of 330 mW at 559.6 nm was obtained for the diode pump power of 13.7 W and the conversion efficiency was about 2.5%. The intense blue emission was also observed in the SrWO₄ crystal when the Raman laser was operating above threshold. This blue emission is centered at 473 nm, which also happened to YVO₄.     

Band-gap engineering of ZnSe quantum dots via a non-TOP green synthesis by use of organometallic selenium compound

Single-step green synthesis of ZnSe quantum dots (QDs) from 1,2,3-selenadiazole and zinc acetate resulted in formation of high-quality mono-disperse ZnSe with engineered band-gap. The present method is a non-TOP green route where oleic acid is used as a surfactant. The size quantization effect can be monitored by UV–visible spectroscopy which shows in the range 370–387 nm (3.20–3.35 eV), a blue shift of about 70–90 nm with respect bulk ZnSe. Photoluminescence measurement revealed band-gap emission at ∼390 nm (3.18 eV, Stokes shift of <10 nm with FWHM <30 nm). Broadened XRD pattern indicated formation of cubic ZnSe and the estimation of particle size from the line broadening at 〈1 1 1〉 matched well the TEM analysis.     

Radioluminescence of synthetic quartz related to alkali ions

The radioluminescence (RL) of synthetic quartzes (GEMMA Quartz & Crystal Company) has been measured at room temperature. Some samples were treated by electrodiffusion (“sweeping”) in order to change the concentrations of alkali ions, mainly Li⁺ and Na⁺, which in quartz are known to be linked to Al ions, substitutional for Si ions.The RL emission spectra show evidence of a role of alkali ions in affecting some specific emissions. All the spectra could be analysed as composed of four bands in the blue and UV region. Specifically, the well known blue emission at around 470 nm was seen to be composed by two bands at 430 nm (2.86 eV) and at 485 nm (2.53 eV). Effects of irradiation, during the RL measurements, were clearly seen only in the “Li swept in” sample, namely an increase in the 485 nm band intensity and a decrease in the 430 nm band one. The previously reported UV emission was detected at 355 nm (3.44 eV) in all the samples, being the most intense band in the “swept out” sample. A further UV emission was detected at 315 nm (3.94 eV), more intense in untreated samples.Possible assignments of the detected emission bands are discussed in relation to the defects of quartz, specifically focusing on the Al centres that are most affected by sweeping procedures.     

Red,green and infrared three-wavelength lasers generated from LD side-pumped Nd3+:YAG crystal

To obtain 1064 nm/532 nm/660 nm three wavelength lasers operating simultaneously or singly, a novel LD side-pumped Nd³⁺:YAG laser system with acousto-optic Q-switched and nonlinear frequency conversion technologies was investigated. When the three wavelength lasers output singly and the Pumping power was 103 W, 1064 nm laser was 14.5 W and the green and red lasers reached 4.7 W and 1.6 W, respectively, at the repetition rate of 10.5 kHz and 11.5 kHz. When they worked simultaneously, the red, green and infrared lasers were obtained with the output power distribution of 1.0 W at 660 nm, 4.3 W at 532 nm and 10.1 W at 1064 nm, and the instability was less than 2% within 3 h.     

Synthesis of nanocrystalline ZnO nanobelts via pyrolytic decomposition of zinc acetate nanobelts and their gas sensing behavior

The pyrolytic decomposition of layered basic zinc acetate (LBZA) nanobelts (NBs) into nanocrystalline ZnO NBs is investigated using scanning electron microscopy (SEM), atomic force microscopy (AFM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and photoluminescence (PL). We also report on the gas sensing response of the resulting ZnO nanomaterial to CO. The LBZA NBs are grown at 65 °C in an aqueous solution of zinc acetate dihydrate. AFM and SEM results show as-grown products possess the characteristic layered structure of the LBZA crystals. XRD and XPS results show that annealing as-grown products at 210 °C in air causes a transformation from zinc acetate to nanocrystalline ZnO NBs via thermal decomposition. The ZnO crystalline domain size increases with temperature from 9.2 nm at 200 °C to 94 nm at 1000 °C, as measured from XRD. SEM shows evidence of sintering at 600 °C. The thickness of the NBs, determined via AFM, ranges from 10 to 50 nm and remains approximately constant with annealing temperature. XPS confirmed the chemical transformation from zinc acetate to ZnO and showed a significant remaining zinc hydroxide component for the ZnO NBs consistent with published results. PL measurements at room temperature show a blue shift in peak emission as the nanobelts change from LBZA to ZnO at 200 °C. Above this transition temperature, the ZnO nanobelts possess strong band edge emission at 390 nm and little broad band emission in the visible region. The AFM and SEM images reveal that the crystallites within the nanobelts orientate in rows along the long axis during annealing. This structure provides a high surface area to volume ratio of aligned nanoparticles which is beneficial for gas sensing applications. Gas sensors fabricated from 400 °C annealed nanobelts showed a response of 1.62 when exposed to 200 ppm of CO in dry air at 400 °C, as defined by the ratio of resistance before and during exposure. This indicates that ZnO nanostructures obtained by thermal decomposition of LBZA NBs could provide a cost effective route to high sensitivity gas sensors.     

Quantum size effect in low energy electron diffraction of thin films

Low energy electron microscopy (LEEM) is used to study the quantum size effect (QSE) in electron reflectivity from thin films. Strong QSE interference peaks are seen below 20 eV for Cu and Ag films on the W(1 1 0) surface and Sb films on the Mo(0 0 1) surface. Simple inspection of QSE interference peaks reveals that all three metals grow atomic layer-by-atomic layer. Layer-specific I(V) spectra obtained with LEEM permit structural analysis by full dynamical multiple scattering LEED calculations for a layer-by-layer view of thin film structure.     

Use of film thickness and Cu additive to improve (0 0 1) texture in MgO/FePtCu(C) bilayers

A multilayer structure has been proposed that demonstrates improved (0 0 1) texture for FePt-based L1₀ perpendicular media. Achieving a strong perpendicular magnetic anisotropy requires aligning the L1₀ crystallographic c-axis along the film normal. The ordered L1₀ FePt structure is tetragonal with a c/a ratio close to 0.965. This makes discriminating between the three crystallographic variants ([1 0 0], [0 1 0], and the desired [0 0 1]) difficult. Alloying FePt with Cu to reduce the c/a ratio and using a multilayer approach to keep the magnetic layers thin results in a structure with an adjustable M_rt and a strong (0 0 1) texture (rocking curve widths around 2°). This is a remarkable improvement in texture from pure FePt multilayered films or monolithic FePt(X) films. The proposed [MgO(2 nm)/Fe_50−xPt₅₀Cu_x(5 nm)]_×n structure limits grain size in the vertical (perpendicular) direction albeit not in the plane of the film. Carbon can be added to the FePtCu layer to reduce the grain size with minimal degradation of the (0 0 1) orientation.