Structural, elastic, electronic and optical properties of a new layered-ternary Ta4SiC3 compound

We propose a new layered-ternary Ta₄SiC₃ with two different stacking sequences (α- and β-phases) of the metal atoms along c axis and study their structural stability. The mechanical, electronic and optical properties are then calculated and compared with those of other compounds M₄AX₃ (M=V, Nb, Ta; A=Al, Si and X=C). The predicted compound in the α-phase is found to possess higher bulk modulus than these compounds. The independent elastic constants of the two phases are also evaluated and the results discussed. The electronic band structures for α- and β-Ta₄SiC₃ show metallic conductivity. Ta 5d electrons are mainly contributing to the total density of states (DOS). We see that the hybridization peak of Ta 5d and C 2p lies lower in energy and the Ta 5d-C 2p bond is stronger than Ta 5d-Si 3p bond. Further an analysis of the different optical properties shows the compound to possess improved behavior compared to similar types of compounds.     

First principles study of electronic and structural properties of the Ge/GeO2 interface

The electronic and structural properties of the Ge/GeO₂ interface are addressed through a density functional simulation scheme which includes the use of hybrid functionals for achieving accurate band gaps, band offsets and defect levels. The present work discusses the germanium dangling bond levels, the thermodynamics of GeO_x, the stability of the oxygen vacancy across Ge/HfO₂ interfaces, the atomic structure of GeO_x, electron and hole trapping in GeO_x, and the band alignment at the Ge/GeO₂ interface.     

First principles investigation of electronic and optical properties of AgAlO2

The electronic and optical properties of AgAlO₂ were determined by using Generalized Gradient Approximation (GGA) suggested by Perdew–Burke–Ernzerhof (PBE) with the addition of Hubbard potential along with linearized augmented plane wave pseudopotential. Our computed band structure infers that our calculated bandgap (1.5?eV) is closer to the experimental (2.81?eV) as compare to the previous theoretical values (1.16?eV). The investigated band structure also reflects that AgAlO₂ is an indirect semiconductor material. The investigated atomic positions and lattice constants are in good agreement with the experimental values than the earlier theoretical values. From presented optical properties one can observe that AgAlO₂ is a good conducting material. The absorption spectrum infers that AgAlO₂ is an expensive material for photo-electronic devices or solar-cell applications.     

First principles study of electronic and optical properties of InAs

The electronic and optical properties of InAs in core-level spectra are calculated using the full-potential linearized augmented plane wave plus local orbitials (FP-LAPW +lo) method. The real and imaginary parts of the dielectric function ε(ω), the optical absorption coefficient I(ω), the reflectivity R(ω), the refractive index n(ω), and the extinction coefficient k(ω)are calculated. All these values are in good agreement with the experimental data. The effect of spin-orbit coupling on optical properties is also investigated and found to be quite small.      

Structural, electronic, elastic and optical properties of fluoro-perovskite KZnF3

We determine the structural, electronic, elastic and optical properties of fluoro-perovskite KZnF₃ using the full potential linear augmented plane wave approach (FP-LAPW) based on the density functional theory (DFT). The exchange-correlation potential is treated by the local density approximation (LDA) and the generalized gradient approximation (GGA). The calculated structural parameters are in good agreement with the available data. We have obtained an indirect band gap. The effect of the pressure on the band gaps is investigated. We evaluate the elastic constants (C_ij), elastic moduli and the Debye temperature. The imaginary and the real parts of the dielectric function ε(ω) and some optical constants are also calculated.     

Electronic and magnetic properties of NdCrSb3: A first principles study

The electronic and magnetic properties of NdCrSb₃ are calculated by the first principles full-potential linearized augmented plane wave (FP-LAPW) method based on the density functional theory (DFT). Density of states (DOS), magnetic moments and band structures of the system are presented. For the exchange and correlation energy, local spin density approximation (LSDA+U) with the inclusion of Hubbard potential U is used. Our calculation shows that the 3d state electron of Cr and 4f state electrons of Nd contribute to the total DOS and the band structures. The effective magnetic moment is found to be 5.77μ_B, which is comparable to the earlier experimental results of NdCrSb₃.     

β-Si3N4电子结构和光学性质的第一性原理研究

采用基于密度泛函的平面波赝势方法(PWP)和广义梯度近似(GGA)，计算了β相氮化硅(β-Si₃N₄)的电子结构和光学性质，得到的晶格常数、能带结构等均与实验结果较好符合.进一步还研究了β-Si₃N₄的光吸收系数以及禁带宽度随外压力的变化规律，为β-Si₃N₄材料在高压条件下的应用提供了理论参考. 关键词： β相氮化硅 电子结构 能带结构 光学性质     

First-principles study of electronic and optical properties of N-doped SrHfO3

The plane-wave ultrasoft pseudopotential technique based on the first-principles density-functional theory (DFT) is used to investigate the doping effect of N substituting for O in cubic SrHfO₃. The calculated results show that the reaction from pure elements to final compounds is favorable and the final compounds are energetically stable. Electronic structure analysis shows the band gaps narrowing with the increase of N concentration due to the presence of the impurity state of N 2p on the top of the valence band and the acceptor energy levels above the Fermi energy, which may be responsible for the red-shift. Besides, the optical absorption edge has been gradually red shifted with increasing N concentration.     

Elastic, electronic, and optical properties of hypothetical SnNNi3 and CuNNi3 in comparison with superconducting ZnNNi3

The elastic, electronic, and optical properties of MNNi₃ (M=Zn, Sn, and Cu) have been calculated using the plane-wave ultrasoft pseudopotential technique, which is based on the first-principle density functional theory (DFT) with generalized gradient approximation (GGA). The optimized lattice parameters, independent elastic constants (C₁₁, C₁₂, and C₄₄), bulk modulus B, compressibility K, shear modulus G, and Poisson's ratio υ, as well as the band structures, total and atom projected densities of states and finally the optical properties of MNNi₃ have been evaluated and discussed. The electronic band structures of the two hypothetical compounds show metallic behavior just like the superconducting ZnNNi₃. Using band structures, the origin of features that appear in different optical properties of all the three compounds has been discussed. The large reflectivity of the predicted compounds in the low energy region might be useful in good candidate materials for coating to avoid solar heating.     

Structural, optical and electrical properties of ZnO/Zn2GeO4 porous-like thin film and wires

Zinc oxide/zinc germanium oxide (ZnO/Zn₂GeO₄) porous-like thin film and wires has been fabricated by simple thermal evaporation method at temperature about 1120 °C for 2.5 h. The structural and optical properties of the porous-like-thin film and wires have been investigated by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD) and photoluminescence (PL) spectroscopy. Metal semiconductor metal (MSM) photodetector structure was used to evaluate the electrical characteristics by using current-voltage (I-V) measurements. Room temperature photoluminescence spectrum of the sample shows one prominent ultraviolet peak at 378 nm and a shoulder at 370 nm. In addition, broad visible blue emission peak at wavelength 480 nm and green emission peak at 500 nm are also observed. Strong photoelectric properties of the MSM in the UV demonstrated that the porous-like-thin film and wires contribute to its photosensitivity and therefore making ZnO/Zn₂GeO₄ wires potential photodetector in the shorter wavelength applications.     

First-principle study of electronic structure and optical properties of 3C-BC4N

The 3C-BC₄N, as a kind of superhard material with many potential practical applications, is studied using first-principle calculations, evaluating the structural parameters, charge transfers, bond populations, band structures, density of states, and optical properties. All the calculations are performed after geometric optimization starting from a six-atom, trigonal, and unit-cell structure. The results indicate the following: all the configurations are metastable; the band gap of five configurations of 3C-BC₄N is highly dependent on the atomic arrangement; BC₄N-1 exhibits insulating behavior; BC₄N-3 exhibits semiconductor or semimetallic behavior, while BC₄N-2, BC₄N-4, and BC₄N-5 exhibit metallic behavior; and all the configurations are transparent in the visible light region.     

First-principles study of electronic structures and optical properties of Cu, Ag, and Au-doped anatase TiO2

We perform first-principles calculations to investigate the band structure, density of states, optical absorption, and the imaginary part of dielectric function of Cu, Ag, and Au-doped anatase TiO₂ in 72 atoms systems. The electronic structure results show that the Cu incorporation can lead to the enhancement of d states near the uppermost of valence band, while the Ag and Au doping cause some new electronic states in band gap of TiO₂. Meanwhile, it is found that the visible optical absorptions of Cu, Ag, and Au-doped TiO₂, are observed by analyzing the results of optical properties, which locate in the region of 400-1000 nm. The absorption band edges of Cu, Ag, and Au-doped TiO₂ shift to the long wavelength region compared with the pure TiO₂. Furthermore, according to the calculated results, we propose the optical transition mechanisms of Cu, Ag, and Au-doped TiO₂. Our results show that the visible light response of TiO₂ can be modulated by substitutional doping of Cu, Ag, and Au.     

The electronic and optical properties of Cu doped CdI2

Based on the density functional pseudopotential method, the electronic structures and the optical properties of CdI₂ doped with Cu are investigated in detail. The calculation results indicate that the defect of Cu(Cd) exists steadily with a certain solubility. For the Cu doped CdI₂, the new highly localized impurity bands induced by Cu 3d states lie just across the Fermi energy at the top of the valence band. The doping of Cu induces reduction of band gap of CdI₂; red shifts are revealed in both the imaginary part of dielectric function and the absorption spectra corresponding to the change in band gaps. Moreover, the study of the reflection spectrum and the loss function shows that the doped Cu is responsible for the increased reflection peak intensity and the red shift of the plasma resonant frequency of CdI₂.     

YFeO3的电子结构和光学性质的第一性原理研究

稀土正铁氧体YFeO₃呈正交钙钛矿结构,其晶体和纳米晶材料在电极材料、 传感器和光催化领域具有重要的应用价值.用平面波赝势方法,采用广义梯度近似、改进的Perdew-Burke-Emzerhof交换-关联势、 实空间超软赝势计算方案,研究了YFeO₃晶体的几何结构、电子结构和光学性质. 计算得到的晶格参量与报道的实验结果一致.通过对能带结构、态密度、介电函数、吸收系数和光电导率的计算和分析, 确定YFeO₃是直接能隙半导体,能隙E_g约为2.22 eV,阐明了YFeO₃晶体和纳米晶具有较好的可见光催化性能.     

ReSi1.75电子结构的第一性原理研究

基于第一性原理全势线性缀加平面波方法和局域密度近似(LDA)，对ReSi_1.75的基态晶格属性进行了研究. 结构优化的结果表明，ReSi_1.75的基态平衡晶格常数比实验值小约0.6%. 在LDA计算基础上，考虑局域的Re的d电子库仑作用，用LDA+U方法计算了ReSi_1.75的电子结构，发现当U_eff=U-J=4.4eV时，能带结构呈半导体性质. 具有0.12eV 关键词： 1.75')" href="#">ReSi_1.75 局域密度近似 自相互修正作用 电子结构     

Concentration-dependent electronic structure and optical absorption properties of B-doped anatase TiO2

The concentration-dependent electronic structures and optical properties of B-doped anatase TiO₂ have been calculated using the density functional theory. The calculated results indicate that the electronic structures of B-doped TiO₂ have changed compared with those of pure TiO₂, which is mainly due to the new midgap states induced by B doping. As to the optical properties, we calculate the imaginary part of dielectric function ε₂(ω) and optical absorption spectra of pure and B-doped TiO₂. Two transitions E₁ and E₂ emerged after B doping. The intensity of absorption is enhanced by B doping both in the UV and visible regions. According to the results of imaginary part of dielectric function ε₂(ω) and DOS, it can be concluded that the two optical transitions correspond to the transitions from the O 2p states in the top of valence band to the midgap states and from the midgap states to the Ti 3d states in the bottom of conduction band, respectively. These results have important implications for the further development of photocatalytic materials.     

Nanoscale ab-initio calculations of optical and electronic properties of LaCrO3 in cubic and rhombohedral phases

We report nanoscale ab-initio calculations of the linear optical and electronic properties of LaCrO₃ in nonmagnetic cubic and rhombohedral phases using the full potential linear augmented plane wave (FP-LAPW) method. In this work the generalized gradient approximation is used for exchange-correlation potential. The dielectric tensor is derived within random-phase approximation. We present results for the band structure, density of states, imaginary and real parts of dielectric tensor, electron energy loss spectroscopy, sum rules, reflectivity, refractive index and extinction coefficient. The regions of transparent, absorption and reflection are discussed. We are not aware of any published experimental or theoretical data for these phases, so our calculations can be used to cover this lack of data for these phases.     

First-principles studies of structural,mechanical, electronic,optical properties and pressure-induced phase transition of CuInO2 polymorph

Using the first-principles density-functional theory within the generalized gradient approximation (GGA), we have investigated the structural, elastic, mechanical, electronic, and optical properties and phase transition of CuInO₂. Structural parameters including lattice constants and internal parameter, pressure effects and phase transition pressure were calculated. We have obtained the elastic coefficients, bulk modulus, shear modulus, Young's modulus and Poisson's ratio. We find that two phases of CuInO₂ are indirect band gap semiconductors (F–Γ and H–Γ for 3R and 2H, respectively). Optical properties, including the dielectric function, refractive index, extinction coefficient, reflectivity, absorption coefficient, loss function and optical conductivity have been obtained for radiations of up to 30 eV.     

Electronic and optical properties of kesterite Cu2ZnSnS4 under in-plane biaxial strains: First-principles calculations

The electronic structures and optical properties of Cu₂ZnSnS₄ (CZTS) under in-plane biaxial strain were systematically investigated using first-principles calculations based on generalized gradient approximation and hybrid functional method, respectively. It is found that the fundamental bandgap at the Γ point decreases linearly with increasing tensile biaxial strain perpendicular to c-axis. However, a bandgap maximum occurs as the compressive biaxial strain is 1.5%. Further increase of compressive strain decreases the bandgap. In addition, the optical properties of CZTS under biaxial strain are also calculated, and the variation trend of optical bandgap with biaxial strain is consistent with the fundamental bandgap.     

A comparative study of electronic structure and magnetic properties of SrCrO3 and SrMoO3

A comparative study of electronic structure and magnetic properties of SrCrO₃ and SrMoO₃ has been carried out using FPLAPW method with density-functional theory. The calculated results suggest that both compounds are nonmagnetic (NM) metal in cubic structures at room temperature, and they exhibit very similar band structure and electronic properties except more extend Mo 4d orbitals than Cr 3d electronic states. However, the electronic structure and magnetic properties exhibit remarkable differences between them in the low temperature phases. SrCrO₃ is with a C-AFM ground state with magnetic moment of 1.18μ_B/Cr in the tetragonal structure, while SrMoO₃ is with a NM ground state in the orthorhombic structure. It is assumed that the extend 4d orbitals may be the reason which results in NM solution at low temperature phase of SrMoO₃.