Surface morphological changes and magnetic properties of Sc-substituted Y3Fe5O12 epitaxial films deposited on the GGG substrate

Sc-doped YIG films were grown on (1 1 1) oriented GGG crystalline substrate with disorientation angle within the range 0-25′. Sc³⁺ ion substitution was varied within the range 0.25-0.3 per formula unit. The films demonstrate different types of surface morphology versus film growth rate and substrate disorientation. Conditions for existence of these types of the surface morphology were defined. The field dependence of magnetic susceptibility at magnetization reversal in film plane and Faraday rotation at wavelength 633 nm for a magnetic field applied in perpendicular direction were measured to characterize the films grown. Films with “mirror-like” surface demonstrate a planar magnetization at room temperature.     

Defect formation and water incorporation in Y2O3

The molecular statics method is used to study the formation of defects and water incorporation in Y₂O₃. The crystal structure, the isothermal compressibility, and the formation enthalpy of Y₂O₃ calculated with the chosen interaction potentials are in good agreement with the experimental data. The formation energies of intrinsic and impurity defects are evaluated. The binding energy of protons and oxygen vacancies with an acceptor impurity at different distances is calculated. Various water incorporation reactions in the oxide are examined, including the mechanisms involving oxygen interstitial sites and oxygen vacancies produced by the acceptor doping. It is shown that the water incorporation in pure Y₂O₃ is energetically less favorable than in the acceptor doped oxide.     

Surface modification of LiMn2O4 thin films at elevated temperature

In order to improve the cycle stability of spinel LiMn₂O₄ electrode at elevated temperature, the LiCoO₂-coated and Co-doped LiMn₂O₄ film were prepared by an electrostatic spray deposition (ESD) technique. LiCoO₂-coated LiMn₂O₄ film shows excellent cycling stability at 55 °C compared to pristine and Co-doped LiMn₂O₄ films. The samples were studied by X-ray diffraction, scanning electron microscopy, Auger electron spectroscopy, cyclic voltammetry and electrochemical impedance spectroscopy. The excellent performance of LiCoO₂-coated LiMn₂O₄ film can be explained by suppression of Mn dissolution. On the other hand, the LiCoO₂-layer on the LiMn₂O₄ surface allows a homogenous Li⁺ insertion/extraction during electrochemical cycles and improves its structure stability.     

An analysis of Y2O3:Eu thin films for thermographic phosphor applications

A comparative study of the luminescent properties of Y₂O₃:Eu³⁺ phosphor powders and thin films sputtered from targets prepared from combustion synthesized powders is reported. Thin films of (Y_0.96Eu_0.04)₂O₃ were deposited on silicon substrates. Films deposited at 600 °C had both monoclinic and cubic phases of Y₂O₃, which developed to an oriented cubic phase after annealing. Films and powders showed a linear dependence of the intensity of the ⁵D₇→⁷F₂ (611 nm) transition with temperature in the range 26-660 °C with an average rate of change of 1.8×10⁻⁴ °C⁻¹. The rate of change appears to be dependent on the Eu³⁺ concentration. This work shows that these thin films can be used as thermographic phosphors for remote temperature measurements.     

Decay dynamics of Eu/Tb in solution-processed Y2O3

As new synthesis techniques are developed to create phosphors with smaller particles the physical processes that govern luminescence behaviors, like efficiency and decay rates, are influenced by the large surface-to-volume ratios of the nano-structured materials. Decay of lanthanide excited states, following pulsed laser excitation, is used to probe the affect of size-induced decay channels on the luminescent properties. We report results on the decay dynamics of europium and terbium excited states in solution-produced yttrium oxide. Radiative decay from the Eu³⁺⁵D₀ state is found to be well described by a single exponential function over a range of concentrations (0.01-2.0%). The Tb³⁺⁵D₄ decay exhibits a distribution of decay rates over the concentration range 0.01-5.0%. The distribution of decay rates is discussed using a probability density function based on the Kohlrausch decay function.     

Dependence of photoluminescent properties of cubic Y2O3:Tb nanocrystals on particle size and temperature

Temperature-dependent spectral properties in the cubic Y₂O₃:Tb³⁺ nanocrystals (NCs, 10-70 nm) under 488 nm excitation were studied and compared to that in the bulk. In NCs, emission lines assigned to the ⁵D₄-⁷F_J (J=1-6) transitions of Tb³⁺ ions and a broad band originated from oxygen defects were observed. As a function of temperature, two intensity maximums of the ⁵D₄-Σ⁷F_J transitions appeared in the NCs, at ∼250 and ∼500 K, while in the bulk only one maximum appeared at ∼250 K. The relative intensity of the maximum at ∼500 K to that at ∼250 K increased with decreasing particle size. The intensity maximum of the band emissions that came from the oxygen defects appeared in the range of 500-600 K. The appearance of intensity maximum as a function of temperature was attributed to the rivalry between thermal quenching process and phonon-assisted excitation. The appearance of two maxima in the NCs was attributed to the luminescence contributed by different Tb³⁺ centers, the internal and the surface. The emission for the surface Eu³⁺ centers has higher quenching temperature in contrast to that for the internal centers.     

The preferential growth of pyrite films prepared by thermal sulfuration of Fe2O3 films

Pyrite thin films were prepared by the sol-gel dip coating process and sulfuration treatment. The evolution of crystal orientation for the pyrite films was investigated as a function of sulfuration temperature. And the effect of crystal orientation on the electrical and optical properties was studied. It was found that films show (1 1 1) preferred orientation after sulfurized at low temperature. However, the (2 0 0) and (3 1 1) mixed preferred orientations were observed when pyrite films were sulfurized at higher temperature. Experimental results also indicate that the carrier concentration is high when the films show (1 1 1) preferred orientation. And the optical absorption coefficient is also large when the films grow with (1 1 1) preferred orientation. It is speculated that surface free energy could play a more important role in determination of preferred orientation when films were sulfurized at low temperature. However, the strain energy plays a more important role in determination of preferred orientation when films were sulfurized at higher temperature.     

Effect of Mg and Ti doping on the luminescence of Y2O3:Eu

The Y₂O₃:Eu³⁺,Mg²⁺,Ti^IV materials (x_Eu: 0.02, x_Mg: 0.08, x_Ti: 0.04) were prepared by solid state reaction. The purity and crystal structure of the material was studied with the X-ray powder diffraction. Luminescence properties were studied in the UV-VUV range with the aid of synchrotron radiation. The emission of Y₂O₃:Eu³⁺,Mg²⁺,Ti^IV had a maximum at 612 nm (λ_exc: 250 nm) due to the ⁵D₀→⁷F₂ transition of Eu³⁺. The excitation spectra (λ_em: 612 nm) showed a broad band at 233 nm, due to the charge transfer transition between O²⁻ and Eu³⁺, and at 297 nm due to the Ti→Eu³⁺ energy transfer. Only very weak persistent luminescence was discovered. In the room and 10 K temperature excitation spectra, the line at 208 nm is due to the formation of a free exciton (FE) and a broad band at 199 nm was related to the valence-to-conduction band absorption of the Y₂O₃ host lattice. The absorption edge was ca. 205 nm giving 6.1 eV as the energy gap of Y₂O₃.     

Meter-long CeO2/YSZ/Y2O3 buffer layers for YBCO coated conductors using DC reactive sputtering

This paper reports CeO₂/YSZ/Y₂O₃ buffer layers deposited on biaxially textured NiW substrates by DC reactive sputtering in a reel-to-reel system. The effect of partial pressure of water vapor (P_H2O) on surface morphology and orientation of the Y₂O₃ films was examined. The obtained CeO₂/YSZ/Y₂O₃ buffer layers exhibit a highly biaxial texture, with in- and out-of-plane FWHM values respectively in the range of 6.0–7.0° and 4.5–5.5°. Crystallographic consistency of CeO₂/YSZ/Y₂O₃ along meter length is excellent. Atomic force microscope observation (AFM) reveals a smooth, continuous and crack-free surface with a Root-mean-square roughness (RMS) lower than 10 nm.     

Growth and characterization of Y2O3 thin films

Y₂O₃ thin films were grown on silicon (1 0 0) substrates by pulsed-laser deposition at different substrate temperatures and O₂ pressures. The structure and composition of films are studied by using X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The Y₂O₃ thin films deposited in vacuum strongly oriented their [1 1 1] axis of the cubic structure and the film quality depended on the substrate temperature. The magnitude of O₂ pressure obviously influences the film structure and quality. Due to the silicon diffusion and interface reaction during the deposition, yttrium silicate and SiO₂ were formed. The strong relationship between composition and growth condition was discussed.     

钇复合氧化物颜料的制备与表征

通过尿素分解法,把三价铬离子掺入到钇铝石榴石Y₃Al₅O₁₂中,采用共沉淀法制备出绿色颜料。扫描电镜测试表明产物颗粒直径在200 nm左右,用XRD测试复合氧化物的结晶相行为,确定主相是钇铝石榴石相,用紫外可见漫反射光谱测试掺杂离子的配位状态和电子跃迁行为,用色度学测试氧化物颜色特征。将复合氧化物颜料颗粒与高分子聚丙烯共混,熔体纺丝,并通过北京同步辐射X射线CT对制得的纤维加以测试,结果表明复合氧化物颜料在高分子基质中得到良好的分散。这种颜料性能稳定,对环境友好,为实现无水印染技术奠定基础,减少纺织印染工业中所排放的污水。     

Curie temperatures of Y3Fe5O12/Gd3Fe5O12 superlattices

The magneto-optical Kerr effects (MOKE) of epitaxial Y₃Fe₅O₁₂/Gd₃Ga₅O₁₂ (YIG/GGG) garnet superlattices grown on (1 1 1)GGG previously by pulsed laser deposition (PLD) were measured. A series of superlattices were investigated with the thickness of the ferrimagnetic YIG layer varied from six unit cells to only one unit cell while keeping the Curie paramagnetic GGG fixed at one unit cell. It was demonstrated that the ellipsometric technique employing photoelastic modulators (PEM) is sensitive enough to measure the MOKE signals of these ultrathin oxide samples. The Curie temperatures, determined by MOKE, are fit with a power law, yielding a shift exponent λ = 3.1 ± 1.2.     

Synthesis and magnetic properties of Sm–Y3Fe5O12 nanoparticles

Garnet nanoparticles Y_3−xSm_xFe₅O₁₂ were fabricated by a sol–gel method. The XRD patterns of all the samples have only peaks of the garnet structure and the sizes range from 34 to 67 nm. Results of VSM show that the saturation magnetization of Y_3−xSm_xFe₅O₁₂ (0<x3) decreases on increasing the Sm concentration x evidently. Meanwhile, it is observed that with the enhancement of the surface spin effects, the saturation magnetization rises as the nanoparticle size is increased.     

Optical properties of new photovoltaic materials: AgCuO2 and Ag2Cu2O3

AgCuO₂ and Ag₂Cu₂O₃ are new types of semiconductor materials. A theoretical study is presented for both the electronic and optical properties of these new photovoltaic materials in the framework of density functional theory (DFT). The calculated cohesive energy is −3.606 eV/atom and −3.723 eV/atom for Ag₂Cu₂O₃ and AgCuO₂, respectively. Electronic calculations indicate that AgCuO₂ is a small band gap semiconductor and Ag₂Cu₂O₃ is metallic in nature. The valency state of Cu is divalent in Ag₂Cu₂O₃ and trivalent in AgCuO₂. The largest absorption coefficient of CuO₂ is 332 244, which is significantly greater than that of CuInSe₂, CdTe, GaAs, etc.     

Surface functionalization, morphology and thermal properties of polyamide6/O-MMT composite nanofibers by Fe2O3 sputter coating

In the present work, the pure polyamide6 (PA6) nanofiber and PA6/organically modified montmorillonite (O-MMT) composite nanofiber were firstly prepared by a facile compounding process with electrospinning, and then coated by nanosize Fe₂O₃ using magnetron sputter technique. The effects of Fe₂O₃ sputter coating on structures, surface morphology and thermal stability were characterized by scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), energy dispersive X-ray spectroscopy (EDX), atomic force microscope (AFM) and thermogravimetric analyses (TGA), respectively. The SEM images showed that the diameters of composite nanofiber were decreased with the loadings of O-MMT and the nanosize Fe₂O₃ is well coated on the surface of the homogeneous and cylindrical nanofibers. The XPS spectra reflected the chemical features of the deposited nanostructures. The EDX confirmed the presence of the O-MMT and Fe₂O₃ in the fibers. The AFM observation revealed that there was a remarkable difference in the surface morphology of composite nanofiber before and after sputter coating. The TGA analysis indicated the barrier effects of silicate clay layers and catalysis effects of Fe₂O₃ improved thermal stability properties of the composite nanofiber.     

Structural and optical properties of Er, Yb co-doped Y2O3 thin films

Thin Er³⁺, Yb³⁺ co-doped Y₂O₃ films were grown on (1 0 0) YAG substrates by pulsed laser deposition. Ceramic targets having different active ion concentration were used for ablation. The influence of the rare-earth content and oxygen pressure applied during the deposition on the structural, morphological and optical properties of the films were investigated. The films deposited at the lower pressure, 1 Pa, and at 1/10 Er to Yb doping ratio are highly textured along the (1 1 1) direction of the Y₂O₃ cubic phase. In addition to the crystalline structure, these films possess smoother surface compared to those prepared at the higher pressure, 10 Pa. All other films are polycrystalline, consisting of cubic and monoclinic phases of Y₂O₃. The rougher surface of the films produced at the higher-pressure leads to higher scattering losses and different behavior of the reflectivity spectra. Optical anisotropy in the films of less than 0.004 was measured regardless of the monoclinic structure obtained. Waveguide losses of about 1 dB/cm at 633 nm were obtained for the films produced at the lower oxygen pressure.     

The thermal spreading of antimony oxides onto Fe2O3

The uniform antimony-rich surface layer on Fe₂O₃ was carried out via thermal spreading of Sb₂O₃ and Sb₂O₄. TG–DTA results indicate that the oxidation temperature of Sb₂O₃ was decreased ca. 100 K due to thermal spreading effect. Although Sb₂O₄ is almost catalytically inert for oxidation of isobutane and Fe₂O₃ is a typical non-selective catalyst for this reaction, the formation of antimony-rich layer suppresses the combustion reactions and favors the partial oxidation reactions. When Sb₂O₄ instead of Sb₂O₃ was used as antimony resource, the enrichment of antimony on Fe₂O₃ surface was much lower. However, the reaction atmosphere of isobutane oxidation enhances antimony spreading over Fe₂O₃ surface. According to Mars–Van Krevelen mechanism, some Sb₂O₄ in catalysts could be intermediately reduced into Sb₂O₃ during reaction of isobutene oxidation, which thermal spreading is much easier. As shown by Raman results, the Sb₂O₄ that has been spread on Fe₂O₃ surface is probably amorphous.     

Annealing temperature influence on electrical properties of ion beam sputtered Bi2Te3 thin films

Ion beam sputtering process was used to deposit n-type fine-grained Bi₂Te₃ thin films on BK7 glass substrates at room temperature. In order to enhance the thermoelectric properties, thin films are annealed at the temperatures ranging from 100 to 400 °C. X-ray diffraction (XRD) shows that the films have preferred orientations in the c-axis direction. It is confirmed that grain growth and crystallization along the c-axis are enhanced as the annealing temperature increased. However, broad impurity peaks related to some oxygen traces increase when the annealing temperature reached 400 °C. Thermoelectric properties of Bi₂Te₃ thin films were investigated at room temperature. The Bi₂Te₃ thin films, including as-deposited, exhibit the Seebeck coefficients of −90 to −168 μV K⁻¹ and the electrical conductivities of 3.92×10²-7.20×10² S cm⁻¹ after annealing. The Bi₂Te₃ film with a maximum power factor of 1.10×10⁻³ Wm⁻¹ K⁻² is achieved when annealed at 300 °C. As a result, both structural and transport properties have been found to be strongly affected by annealing treatment. It was considered that the annealing conditions reduce the number of potential scattering sites at grain boundaries and defects, thus improving the thermoelectric properties.     

Wavelet analysis of the surface morphologic of nanocrystalline TiO2 thin films

Surface morphologies of nanocrystalline TiO₂ thin films were studied by analyzing the surface profile of AFM images using wavelet transform method. Based on characterizing the fractal feature and computing the image details at different orientations and resolutions, the surface textures of nanocrystalline TiO₂ thin films before and after chemical treatment were examined. The results reveal that titanium isopropoxide treatment leads to an increase of surface roughness. The related mechanism of modification of the microstructure by chemical treatment associated with the improvement of the photocurrent response is discussed.     

Effect of annealing temperature on the decomposition of reactively sputtered Ag2Cu2O3 films

Ag₂Cu₂O₃ films were deposited on glass substrates by reactive sputtering of a composite silver-copper target. The deposited films were annealed in air at 100, 200 and 300 °C. The structure of the films was studied using X-ray diffraction (XRD), their surface morphology was characterised using scanning electron microscopy (SEM) and their electrical resistivity at room temperature was measured using the four point probe method. The 100 °C annealing did not modify either the film structure or the film morphology. On the other hand, Ag₂Cu₂O₃ films were partially decomposed into Ag and CuO after a 200 °C annealing. The decomposition was complete for a 300 °C annealing. The evolution of the film surface morphology as a function of the annealing temperature was discussed in connection to the evolution of the molar volume of the phases constituting the films.