Determination of common inorganic anions and cations by non-suppressed ion chromatography with column switching

An ion chromatography (IC) method has been proposed for the determination of seven common inorganic anions (F(-), H(2)PO(4)(-), NO(2)(-), Cl(-), Br(-), NO(3)(-), and SO(4)(2-)) and/or five common inorganic cations (Na(+), NH(4)(+), K(+), Mg(2+), and Ca(2+)) using a single pump, a single eluent and a single detector. The present system used cation-exchange and anion-exchange columns connected in series via a single 10-port switching valve. The 10-port valve was switched for the separation of either cations or anions in a single chromatographic run. When 1.0mM trimellitic acid (pH 2.94) was used as the eluent, the seven anions and the five cations could be separated on the anion-exchange column and the cation-exchange column, respectively. The elution order was found to be F(-)相似文献   

Long-chain alkylimidazolium ionic liquids, a new class of cationic surfactants coated on ODS columns for anion-exchange chromatography

Separations of common inorganic anions were carried out on ODS columns coated with two long-chain alkylimidazolium ionic liquids ([C(12)MIm]Br and [C(14)MIm]Br) as new cationic surfactants for ion chromatography. With phthalate buffer solution as the mobile phases and non-suppressed conductivity detection, high column efficiencies and excellent selectivity were obtained in the separation of inorganic anions. Chromatographic parameters are calculated and the results show that the coated column possesses significant potential for the analysis of some inorganic anions such as CH(3)COO(-), IO(3)(-), Cl(-), BrO(3)(-), NO(2)(-), Br(-), NO(3)(-), SO(4)(2-), I(-), BF(4)(-), and SCN(-). The effect of eluent pH values on the separation of anions has been studied on the column coated with [C(12)MIm]Br. The stability of the coated columns was also examined.     

Development of packed-column suppressor system for capillary ion chromatography and its application to environmental waters

A novel suppressor unit for capillary ion chromatography was designed to reduce the background conductivity and at the same time to increase the analyte signal. Regeneration of the suppressor was carried out on-line by passing an appropriate acidic solution through the column to displace the accumulated eluent cations. By using two 6-port microswitching valves and two packed capillary column suppressors, the background conductivity of sodium carbonate-bicarbonate mobile phase was maintained at low conductivity for continuous chromatographic runs, and the detection limits at low ppb levels were achieved. The relative standard deviations (RSDs) for the retention time, peak area and peak height of six common inorganic anions (0.05mM each of F(-), Cl(-), NO(2)(-), Br(-), NO(3)(-) and SO(4)(2-)) were between 0.5-0.9, 1.1-4.6 and 0.7-4.9%, respectively. The present system was successfully applied to the determination of inorganic anions in river water and tap water samples.     

Application of ion chromatography to the determination of inorganic anions in foodstuffs.

A review on the applications of ion chromatography (IC) to the determination of inorganic anions in foodstuffs is presented. The anions were commonly determined in food, i.e., SO3(2-), NO3- and NO2-, and to a lesser extent Cl-, Br-, I-, SO4(2-), IO3-, BrO3- and phosphate, are considered. In comparison with standard methods for the determination of anions in food products, chromatographic methods are rapid, sensitive and precise. They also have the advantage of determining several ions simultaneously. The separation may be achieved by conventional IC, by ion interaction chromatography or by ion exclusion chromatography. IC has also been applied to the determination of Br, I, N and S in foods after oxidation or combustion of samples and conversion into anionic forms.     

Determination of trace anions in liquefied petroleum gas using liquid absorption and electrokinetic migration for enrichment followed by ion chromatography

A simple sample enrichment technique, electrokinetic migration enrichment in single phase using a designed device, coupled with ion chromatography is presented for the determination of four anions (H(2)PO(4)(-), Cl(-), NO(3)(-), and SO(4)(2-)) in liquefied petroleum gas by liquid adsorption. The electrokinetic migration enrichment is based on the phenomenon of ion electrokinetic migration to the opposite electrode. When the anions migrated to the anode in a smaller volume chamber under the electric field, the concentration was realized. The main parameters affecting enrichment efficiency of applied voltage and enrichment time were investigated. The ion chromatography condition for anions separation was also studied. Under the optimal electrokinetic migration enrichment and ion chromatography conditions, the four anions were detected simultaneously with good linear relationship (r(2) = 0.9908-0.9968) and high precisions (less than 5% of the relative standard deviations of peak areas). The limits of detection of anions (S/N of 3) were in the range of 8-600 μg L(-1). The enrichment factors of the four anions ranged from 3.1 to 5.8. The established method was successfully applied to the analysis of the trace anions in liquefied petroleum gas by liquid adsorption with satisfactory results. The advantages of this method are simple operation and low cost.     

Sampling and analysing mixtures of sulphate, sulphite, thiosulphate and polythionate

Interpreting the redox chemistry of sulphur in aqueous systems requires the analysis of mixtures of various sulphoxy anions. Previous methods have been too involved to permit high sample throughout if good quality control is to be maintained. Methods based on ion chromatography have been developed for the direct determination of SO(2-)(4), SO(2-)(3), S(2)O(2-)(3), and SCN(-). The determination of thiocyanate permits the indirect determination of polythionates by treatment with cyanide. Formate, acetate, F(-), Cl(-), CO(2-)(3), and PO(3-)(4), do not interfere, but NO(-)(2) and NO(-)(3) interfere with determination of SO(2-)(3),. The sample preservation treatment includes addition of formaldehyde, cation-exchange and cold storage, to retard oxidation of S(2)O(2-)(3), and SO(2-)(3), and inhibits the rearrangement of SO(2-)(3),/S(2)O(2-)(3),/S(n)O(2-)(6), mixtures caused by bimolecular nucleophilic displacement (S(N)2) reactions. Treated samples may be stored for up to 6 weeks with only minor loss of thiosulphate.     

Determination of atmospheric concentrations of inorganic anions by ion chromatography following ultrasonic extraction

The capability of the suppressed conductometric detection ion chromatography (IC) was investigated for the separation and determination of inorganic anions (F-, Cl-, NO3- and SO4(2-)) in standard reference materials SRM-1648 urban particulate matter following ultrasonic extraction. The effects of the cationic surfactant (SDS) and the anionic surfactant (CTAB) on ultrasonic extraction efficiency of inorganic anions from complex matrix of airborne particulate matter were investigated. The results showed that surfactant can enhance the extraction efficiency. Finally, the concentrations of inorganic anions in the atmosphere of the city of Isfahan were determined. The results showed a trend of SO4(2-) > NO3- > Cl- > F-.     

有机酸与无机阴离子的梯度离子色谱法分析研究

研究了用离子色谱法梯度洗脱抑制电导检测器分析有机酸与无机阴离子的色谱条件,建立了最佳梯度程序。用阴离子交换分离,选用去离子水、氢氧化钠和甲醇作淋洗液,分别对５种二元有机酸和３种无机阴离子做二元梯度淋洗,对１０种多元有机酸和３种无机阴离子做三元梯度淋洗。方法用于果汁饮料与柠檬酸发酵液的测定,结果令人满意。     

Functionalized polymeric stationary phases for ion chromatography

Synthesis and properties of the multilayered stationary phases, which contain quaternary amine functional groups for the analysis of anions by ion chromatography, are described. The bonded phases were characterized by elemental analysis, solid-state (13)C NMR spectroscopy and chromatographic methods. The surface of 1,4-di(2-hydroxy-3-methacryloyloxypropoxy)phenol (solid support) was coated with polymeric layers formed by condensation polymerization of primary amine with diepoxide. Each layer of the anion exchange stationary phase consists of copolymer of methylamine (MA) and 1,4-butanedioldiglycidyl ether (BDDE). A series of stationary phases with different numbers of polymerized layers were tested. The separation of an inorganic anions sample (F(-), Cl(-), NO(2)(-), Br(-), NO(3)(-), additionally HPO(4)(2-) and SO(4)(2-)) was performed. In the measurement, a hydroxide, carbonate, bicarbonate and their mixture were used as mobile phases.     

Simultaneous determination of trace amounts of borate, chloride and fluoride in nuclear fuels employing ion chromatography (IC) after their extraction by pyrohydrolysis

An accurate and sensitive method based on the combination of pyrohydrolysis-ion chromatography (PH-IC) is proposed for the simultaneous separation and determination of boron as borate, chloride and fluoride in nuclear fuels such as U(3)O(8), (Pu,U)C and Pu-alloys. The determination is based on the initial pyrohydrolytic extraction of B, Cl and F from the samples as boric acid, HCl and HF, respectively, which are subsequently separated by ion chromatography (IC). The proposed method significantly improves the existing analytical methodology as it combines the determination of boron, a critical trace constituent in nuclear materials, along with F(-) and Cl(-) for chemical quality control measurements. Various experimental parameters were optimized to achieve maximum recoveries of the analytes during the pyrohydrolysis and to get better ion chromatographic (IC) separation of borate, F(-) and Cl(-) along with other anions such as CH(3)COO(-), NO(2)(-), NO(3)(-), Br(-), PO(4)(3-) and SO(4)(2-). Recoveries of more than 93% could be obtained for all the analytes in the sample (0.5-1.5 g) at 1200+/-25K and distilled with pre-heated steam at the flow rate of 0.3 mL/min. An isocratic elution with a mobile phase of 0.56 M d-mannitol in 6.5mM NaHCO(3) was used for the IC separation. The detection limits for B (as borate), F(-) and Cl(-) were 24, 13 and 25 microgL(-1), respectively. Precision of about 5% was achieved for determination of boron, Cl(-) and F(-) in the samples containing 1-5 ppm(w) of boron, and 10-25 ppm(w) of Cl and F. The method was validated with reference materials and successfully applied to the nuclear fuels. The methodology is easy to adapt on routine basis.     

Suppressed electrostatic ion chromatography with tetraborate as eluent and its application to the determination of inorganic anions in snow and rainwater

Tetraborate is investigated as the eluent ion for suppressed electrostatic ion chromatography (EIC) using a zwitterionic stationary phase. Good separation of a range of inorganic anions (SO4(2-), Cl-, NO3-, Br-, NO3-, ClO3-, and I-) was obtained, with detection limits for highly conducting ions (SO4(2-), Cl-, NO2-, Br- , and NO3-) being less than 8 x 10(-8) M, and for weakly conducting anions (ClO3- and I-) being 2.7 x 10(-7) and 5.8 x 10(-7) M, respectively. Calibration curves were linear up to 1.8 mM of each analyte. Retention times were found to increase with increasing eluent concentration and a linear relationship was observed between log k' and log[Na2B4O7] for all analytes. This behaviour is attributed to the progressive formation of a binary electrical double layer at the surface of the zwitterionic stationary phase. Retention times of analytes could be manipulated by varying the concentration of the eluent. This new suppressed-EIC system was applied to the determination of inorganic anions (SO4(-2) , CI-, NO3-, NO2-, and Br-) in snow and rainwater samples.     

离子色谱法同时测定茶叶中多种阴离子

研究了离子色谱法同时测定茶叶中F<'->、Cl<'->、NO<,2><'->、NO<'-><,3>、H<,2>PO<'-><,4>和SO<'2-><,4>6种无机阴离子含量的方法.茶叶样品中6种阴离子经95℃超声浸提20 min后,以浓度为1.92 mmol/L Na<,2>CO<,3>和1.80 mmol/L NaH...     

Determination of inorganic anions by ion chromatography using a graphitized carbon column dynamically coated with cetyltrimethylammonium ions.

The simultaneous determination of inorganic anions by ion chromatography using a dynamically coated graphitized carbon column with cetyltrimethylammonium (CTA) ions was investigated with suppressed conductivity detection. Column preparations with CTA and sodium carbonate-sodium hydrogencarbonate concentration in the eluent were examined to optimize the separation of seven common anions (F-, Cl-, NO2-, Br-, NO3-, HPO(4)2- and SO(4)2-). Calibration curves were linear from 0.5 to 5 micrograms/ml for F-, from 1.0 to 10 micrograms/ml for Cl-, from 1.5 to 15 micrograms/ml for NO2-, from 2.0 to 20 micrograms/ml for Br- and NO3-, from 5.0 to 50 micrograms/ml for HPO(4)2- and from 3.0 to 30 micrograms/ml for SO(4)2- with correlation coefficients (r) of 0.999 or better. The relative standard deviations of peak areas were between 0.3 and 0.9% for 10 repeated measurements. The application of this newly developed method was demonstrated by the determination of inorganic anions in the water for pharmaceutical purposes. Using CTA-Br as the coating agent, a permanently coated ion-exchange column was obtained, which allowed efficient separations of seven anions without adding any coating agent to the eluent.     

Reversed-phase liquid chromatograhy/electrospray ionization tandem mass spectrometry for analysis of perchlorate in water

A new reversed-phase liquid chromatograhy/electrospray ionization tandem mass spectrometry method was developed for the analysis of perchlorate in water. The improved separation of perchlorate from common anions along with sample dilution effectively reduced matrix effects, primarily ion suppression caused by common anions. The (18)O-enriched perchlorate used as an internal standard provided further compensation for potential changes associated with instrument sensitivity, retention time shifting, peak broadening, ion suppression, and other matrix effects. The mean recoveries and relative standard deviations were 92-107% and 2.5-9.5% for simulated water matrix spikes at 0.05-1.0 microg/L, and 80-106% and 3.8-13% for real water sample matrix spikes at 2.0 microg/L, respectively. The method detection limits were 0.007 microg/L for reagent water and 0.014 microg/L for the simulated water matrix that contained 100 mg/L of SO(4)(2-), CO(3)(2-), and Cl(-) anions; 2 mg/L of PO(4)(3-) as P and NO(3)(-) as N; and 0.1 mg/L of Br(-), BrO(3)(-), ClO(2)(-), ClO(3)(-), and F(-) anions in reagent water, respectively. When using cartridge pretreatment to remove problematic SO(4)(2-), CO(3)(2-), and Cl(-) anions, the minimum reporting level could be set to 0.05 microg/L or lower. With 10-fold dilution, the minimum reporting level was conservatively set to 0.5 microg/L.     

High-speed simultaneous ion-exclusion/cation-exchange chromatography of anions and cations on a weakly acidic cation-exchange resin column

The simultaneous ion-exclusion/cation-exchange separation column packed with a polymethacrylate-based weakly acidic cation-exchange resin of 3 microm particle size was used to achieve the simultaneous high-speed separation of anions and cations (Cl(-), NO3(-), SO4(2-), Na(+), K(+), NH4(+), Ca(2+) and Mg(2+)) commonly found in environmental samples. The high-speed simultaneous separation is based on a combination of the ion-exclusion mechanism for the anions and the cation-exchange mechanism for cations. The complete separation of the anions and cations was achieved in 5 min by elution with 15 mM tartaric acid-2.5 mM 18-crown-6 at a flow-rate of 1.5 ml/min. Detection limits at S/N=3 ranged from 0.36 to 0.68 microM for anions and 0.63-0.99 microM for cations. This method has been applied to the simultaneous determination of anions and cations in several environmental waters with satisfactory results.     

Dendrimer modified silica gel for anion exchange chromatography: synthesis, characterization and application

The novel grafted silica supports were investigated. The anion exchanger was prepared by chemical modification of a bare silica gel surface. The support was coated with a polymeric moiety formed by condensation polymerization of primary amine with diepoxide. The synthesized copolymer of methylamine (MA) and 1,4-butanedioldiglycidyl ether (BDDE) exhibited a dendrimer structure. The prepared materials were characterized by elemental analysis, FT-IR spectroscopy and solid state (13)C and (29)Si NMR CP-MAS spectroscopy. The porous structure of the adsorbents was investigated using the low temperature nitrogen adsorption (LTNA) method. It allows determination of the influence of the topology of packing materials on their chromatographic properties. Imaging was also carried out on the surfaces of the synthesized materials by scanning electron microscopy (SEM). The obtained stationary phase was applied in ion chromatography for the separation of inorganic anions (F(-), Cl(-), NO(2)(-), Br(-), NO(3)(-), HPO(4)(2-), SO(4)(2-), ClO(4)(-)). Bicarbonate buffer was used as a mobile phase.     

Evaluation of microchip capillary electrophoresis with external contactless conductivity detection for the determination of major inorganic ions and lithium in serum and urine samples

The determination of inorganic ions in clinical samples in less than 90 seconds was demonstrated for microchip capillary electrophoresis using capacitively coupled contactless conductivity detection (C(4)D). Bare electrophoresis chips were used in combination with external electrodes which were part of the chip holder. In order to achieve the required selectivity and sensitivity, an optimization of the electrode layout was carried out. Limits of detection (LOD) of 1 microM for K(+), 1.5 microM for Ca(2+), 3 microM for Na(+), 1.75 microM for Mg(2+) and 7.5 microM for Li(+) were achieved. The determination of inorganic cations (NH(4)(+), K(+), Na(+), Ca(2+), Mg(2+)) and anions (Cl(-), NO(3)(-), SO(4)(2-), phosphate) in blood serum and urine samples was possible in one common electrolyte solution containing 15 mM L-arginine, 10.75 mM maleic acid and 1.5 mM 18-crown-6 at pH 5.90 by simply switching the separation voltage from positive to negative polarity. Lithium, present at significant levels when used for therapeutic purposes, can also be determined in blood serum using a slightly modified background electrolyte solution.     

同时测定无机离子的改良离子色谱法在河水和废水质量监控中的应用（英文）

In this study,our recent work on advanced ion chromatographic methods for the simultaneous determination of inorganic ionic species such as common anions(SO2-4,Cl-and NO-3) and cations(Na+,NH+4,K+,Mg2+,and Ca2+),nutrients(phosphate and silicate) and hydrogen ion/alkalinity are summarized first.Then,the applications using these methods for monitoring environmental water quality are also presented.For the determination of common anions and cations with nutrients,the separation was successfully performed by a polymethacrylate-based weakly acidic cation-exchange column of TSKgel Super IC-A/C(Tosoh,150 mm×6.0 mm i.d.) and a mixture solution of 100 mmol/L ascorbic acid and 4 mmol/L 18-crown-6 as acidic eluent with dual detection of conductivity and spectrophotometry.For the determination of hydrogen ion/alkalinity,the separation was conducted by TSKgel ODS-100Z column(Tosoh,150 mm×4.5 mm i.d.) modified with lithium dodecylsulfate and an eluent of 40 mmol/L LiCl/0.1 mmol/L lithium dodecylsulfate/0.05 mmol/L H2SO4 with conductivity detector.The differences of ion concentration between untreated and treated wastewater showed the variation of ionic species during biological treatment process in a sewage treatment plant.Occurrence and distribution of water-quality conditions were related to the bioavailability and human activity in watershed.From these results,our advanced ion chromatographic methods have contributed significantly for water quality monitoring of environmental waters.     

Determination of chloride, nitrate, sulphate and total sulphur in environmental samples by single-column ion chromatography

The analytical performance characteristics of a single-column ion chromatography system are reported. The data were obtained by using conductivity detection as well as by an indirect ultraviolet technique. The method has been applied to the determination of Cl(-), NO(3)(-) and SO(4)(2-) in samples of rain, sewer water, and soil-pore water. Also described are two methods which allow ion Chromatographic analysis of CaS0(4)-extractable nitrate in soils, and total sulphur in soils, marine sediments and plant tissue.     

Simultaneous and Fast Detection of Anions in Snow Using Short Tube by Capillary Zone Electrophoresis

A capillary zone electrophoresis (CZE) method applied short-effective length of capillary (11 cm) and low separation voltage (5 kV) was developed for the fast and quantitative determination of Cl m , $ {\rm NO}_2^ - $ , $ {\rm SO}_4^{2 - } $ , $ {\rm NO}_3^ - $ , $ {\rm HCO}_3^ - $ in snow sample. Baseline separation of inorganic anions and organic anions was achieved within 55 s. Indirect absorbance detection of anions was accomplished with a chromate - based background electrolyte modified with cetyltrimethylammonium bromide (CTAB) and acetonitrile at pH 9.5. The effect of the pH, the concentration of electrolyte and modifiers on the resolution was investigated. The application of electrokinetic injection using butyric acid as internal standard created the described method fast, sensitive, and quantitative, with good relative standard deviation (RSD), for migration times from 0.1 to 0.3% and for peak areas from 1.8 to 4.0%. The limits of detection (LOD) were 0.03 mg L m 1 Cl m , 0.1 mg L m 1 $ {\rm NO}_2^ - $ , 0.07 mg L m 1 $ {\rm SO}_4^{2 - } $ , 0.08 mg L m 1 $ {\rm NO}_3^ - $ , 0.05 mg L m 1 F m , and 0.2 mg L m 1 $ {\rm HCO}_3^ - $ , respectively. Standard addition recoveries of Cl m , $ {\rm NO}_2^ - $ , $ {\rm SO}_4^{2 - } $ , $ {\rm NO}_3^ - $ , F m , and $ {\rm HCO}_3^ - $ in snow sample were between 91 and 104%. This method has been shown promising results for the determination of small anions in snow sample.