In situ derivatization reaction and determination of ibuprofen in water samples using headspace generation-programmed temperature vaporization-gas chromatography-mass spectrometry

The aim of the present work is to propose a method for the determination of ibuprofen, as a typical representative of pharmaceutical compounds, in aqueous samples. To do so, an in situ derivatization reaction in aqueous medium was employed in the vial of a headspace sampler (HS), after which instrumental measurements were made with gas chromatography-mass spectrometry (GC-MS). As the injection system we propose a programmed temperature vaporizer (PTV) where, in solvent vent mode, better results can be obtained than with the conventional split and splitless injection modes. Since the derivatization reaction takes place in the HS vial, after the mixing of reagents and the sealing of the vial, the whole process takes place on-line, with no need for intermediate steps. The simplicity and speed of the method – analysis throughput: 10.5 min – together with the limit of detection obtained (0.23 μg/L), bearing in mind that no preconcentration step or later clean-up step are required, make this a good method for the analysis of ibuprofen in aqueous samples of urban waste water.     

Microextraction by packed sorbent for the analysis of pharmaceutical residues in environmental water samples by in situ derivatization-programmed temperature vaporizer-gas chromatography-mass spectrometry

The present work describes the development and validation of a method for the determination of five non-steroidal anti-inflammatory drugs (NSAIDs: clofibric acid, ibuprofen, naproxen, diclofenac and ketoprofen) in water samples. The fully automated method includes in situ aqueous derivatization followed by analyte enrichment by microextraction by packed sorbent (MEPS) coupled directly to programmed temperature vaporizer-gas chromatography-mass spectrometry (PTV-GC-MS). The MEPS variables, such as sample volume, elution solvent, elution volume, fill and injection speed and washing steps were optimized. It was possible to use the MEPS polymer (silica-C18) 250 times. Ibuprofen-d3 was used as internal standard. The reproducibility of the method, calculated as the relative standard deviation (RSD), was below 10% for all compounds. Detection limits in ultrapure water were between 3.0 and 110 ngL(-1) for ibuprofen and ketoprofen, respectively. External calibration was used in the determination of NSAIDs in several types of water samples, including tap, river, sea and influent and effluent wastewater. The results obtained revealed the presence of ibuprofen and naproxen in the influent wastewater sample and of naproxen in the effluent wastewater sample.     

In situ aqueous derivatization and determination of non-steroidal anti-inflammatory drugs by salting-out-assisted liquid-liquid extraction and gas chromatography-mass spectrometry

A new analytical method for the determination of trace levels of five non-steroidal anti-inflammatory drugs (NSAIDs: clofibric acid, ibuprofen, naproxen, diclofenac and ketoprofen) in water samples is described. The analytical procedure involves in situ aqueous derivatization with N-(3-dimethylaminopropyl)-N'-ethylcarbodiimide hydrochloride (EDC) and 2,2,2-trifluoroethylamine hydrochloride (TFEA) and salting-out liquid-liquid extraction (SALLE), followed by gas chromatography-programmed temperature vaporizer-mass spectrometry (GC-PTV-MS). The influence of several parameters on the efficiency of the derivatization (stirring time, reaction time, reagent concentration and pH), and the extraction (solvent, volume, salts and stirring time) and injection steps (liner, injection volume, liner temperature, injection time, venting time and venting flow) was investigated. The detection limits of the method in water varied from 0.042 μg/L for ibuprofen to 1.2 μg/L for ketoprofen. The relative standard deviations (RSD) values were found to be relatively low (<10% for all compounds). The methodology developed was applied to the determination of NSAIDs in several environmental matrices including tap, river, sea and influent and effluent waste water samples. The results obtained show the presence of ibuprofen and naproxen in the influent waste water sample.     

Simultaneous amperometric determination of lignin peroxidase and manganese peroxidase activities in compost bioremediation using artificial neural networks

High-performance liquid chromatography (HPLC) and fluorescence derivatization were applied for a nanogram-level N-nitrosodimethylamine (NDMA) analysis of water samples. For the analysis of N-nitrosodimethylamine, samples were first denitrosated by a mixed solution of hydrobromic acid and acetic acid to produce dimethylamine, which was derivatized with dansyl chloride for HPLC fluorescence detection. Fluorescence detection was optimized with excitation and emission wavelengths of 340 and 530 nm, respectively. pH adjustment after denitrosation was necessary to maximize fluorescence intensity with pHs in the range of 9-12. A dansyl chloride concentration of 500 mg l⁻¹ was found to be optimal for measuring a fluorescence signal. An instrumental detection limit of 0.1 ng of NDMA was possible with fluorescence derivatization. The NDMA in water samples was extracted by continuous solid-phase extraction using Ambersorb 572. Although the determination of NDMA was variable at lower concentrations (less than 200 ng l⁻¹), it was observed that the NDMA detection limit with this method could be lowered to a concentration of 10 ng l⁻¹. Another benefit of this method can be found in its selectivity for NDMA. Unlike gas chromatographic (GC) methods, this method generates a distinct peak for NDMA without interference even in the complex matrix of wastewater effluents. The HPLC with fluorescence derivatization method may be applicable for determining NDMA in water and wastewater samples for various research purposes and for screening environmental samples.     

Development of single‐drop microextraction and simultaneous derivatization followed by GC‐MS for the determination of aliphatic amines in tobacco

In this work, for the first time, headspace (HS) single‐drop microextraction and simultaneous derivatization followed by GC‐MS was developed to determine the aliphatic amines in tobacco samples. In the HS extraction procedure, the mixture of derivatization reagent and organic solvent was employed as the extraction solvent for HS single‐drop microextraction and in situ derivatization of aliphatic amine in the samples. Fast extraction and simultaneous derivatization of the analytes were performed in a single step, and the obtained derivatives in the microdrop extraction solvent were analyzed by GC‐MS. The optimized experiment conditions were: sample preparation temperature of 80°C and time of 30 min, HS extraction solvent (the mixture of benzyl alcohol and 2,3,4,5,6‐pentafluorobenzaldehyde) volume of 2.0 μL, extraction time of 90 s. With the optimal conditions, the method validations were also studied. The method has good linearity (R² more than 0.99), accepted precision (RSD less than 13%), good recovery (98–104%) and low limit of detection (0.11–0.97 μg/g). Finally, the proposed technique was successfully applied to the analyses of aliphatic amines in tobacco samples of seven different brands. It was further demonstrated that the proposed method offered a simple, low‐cost and reliable approach to determine aliphatic amines in tobacco samples.     

Enantioselective analysis of ibuprofen, ketoprofen and naproxen in wastewater and environmental water samples

A highly sensitive and reliable method for the enantioselective analysis of ibuprofen, ketoprofen and naproxen in wastewater and environmental water samples has been developed. These three pharmaceuticals are chiral molecules and the variable presence of their individual (R)- and (S)-enantiomers is of increasing interest for environmental analysis. An indirect method for enantioseparation was achieved by the derivatization of the (R)- and (S)-enantiomers to amide diastereomers using (R)-1-phenylethylamine ((R)-1-PEA). After initial solid phase extraction from aqueous samples, derivatization was undertaken at room temperature in less than 5 min. Optimum recovery and clean-up of the amide diastereomers from the derivatization solution was achieved by a second solid phase extraction step. Separation and detection of the individual diastereomers was undertaken by gas chromatography-tandem mass spectrometry (GC-MS/MS). Excellent analyte separation and peak shapes were achieved for the derivatized (R)- and (S)-enantiomers for all three pharmaceuticals with peak resolution, R(s) is in the range of 2.87-4.02 for all diastereomer pairs. Furthermore, the calibration curves developed for the (S)-enantiomers revealed excellent linearity (r(2) ≥ 0.99) for all three compounds. Method detection limits were shown to be within the range of 0.2-3.3 ng L(-1) for individual enantiomers in ultrapure water, drinking water, surface water and a synthetic wastewater. Finally, the method was shown to perform well on a real tertiary treated wastewater sample, revealing measurable concentrations of both (R)- and (S)-enantiomers of ibuprofen, naproxen and ketoprofen. Isotope dilution using racemic D(3)-ibuprofen, racemic D(3)-ketoprofen and racemic D(3)-naproxen was shown to be an essential aspect of this method for accurate quantification and enantiomeric fraction (EF) determination. This approach produced excellent reproducibility for EF determination of triplicate tertiary treated wastewater samples.     

气相色谱-质谱法测定水体中5种典型有机紫外防晒剂

建立了水体中5种典型有机紫外防晒剂甲氧基肉桂酸乙基己酯（ethylhexyl methoxycinnamate,EHMC）、二苯酮-3（benzophenone-3,BP-3）、4-甲基苄亚基樟脑（4-methylbenzylidene camphor,4-MBC）、奥克立林（octocrylene,OC）和胡莫柳酯（homosalate,HMS）的气相色谱-质谱检测方法。对HMS、BP-3衍生化条件进行了系统的优化。以100 μL双（三甲基硅烷基）三氟乙酰胺（N,O-bis（trimethylsilyl） trifluoroacetamide,BSTFA）为衍生化试剂,在100 ℃下反应100 min。水样固相萃取选用Oasis HLB萃取柱（0.5 g）,洗脱溶剂为乙酸乙酯-二氯甲烷（1：1,v/v）,水样pH 3~5。该方法对5种化合物的检出限范围为0.5~1.2 ng/L,定量限范围为1.4~4.0 ng/L。最佳实验条件下,加标水样回收率为87.85%~102.34%,相对标准偏差（n=3）均小于5%。该方法成功地应用于昆明市第一污水厂进出口水样中目标物质的分析。     

超高效液相色谱法同时测定布洛芬注射液中布洛芬和精氨酸的含量

建立了一种同时测定布洛芬注射液中布洛芬和精氨酸含量的超高效液相色谱方法。精氨酸与衍生化试剂2,4-二硝基氟苯(DNFB)反应后,与布洛芬同时在超高效液相色谱-二极管阵列检测器(UPLC-PDA)上检测。采用BEH C18色谱柱(50 mm×2.1 mm, 1.7 μm),以乙腈-0.05 mol/L磷酸二氢钾缓冲液(pH 2.5)为流动相进行梯度洗脱,流速为0.4 mL/min,柱温为30 ℃,检测波长分别为357 nm(精氨酸衍生物)和220 nm(布洛芬)。结果表明,布洛芬与精氨酸分别在2.0～100.5 mg/L和1.7～84.5 mg/L范围内呈良好的线性关系,相关系数(r)均为0.9997;平均回收率分别为99.8%和99.6%,相对标准偏差(RSDs)分别为0.37%和0.25%;定量限(信噪比（S/N）=10)分别为0.1 ng和0.2 ng;检出限(S/N=3)分别为0.03 ng和0.05 ng。本方法快速、准确,重复性好,可较全面地评价布洛芬注射液的质量。     

Determination of filbertone in spiked olive oil samples using headspace-programmed temperature vaporization-gas chromatography–mass spectrometry

A sensitive method for the fast analysis of filbertone in spiked olive oil samples is presented. The applicability of a headspace (HS) autosampler in combination with a gas chromatograph (GC) equipped with a programmable temperature vaporizer (PTV) and a mass spectrometric (MS) detector is explored. A modular accelerated column heater (MACH^TM) was used to control the temperature of the capillary gas chromatography column. This module can be heated and cooled very rapidly, shortening total analysis cycle times to a considerable extent. The proposed method does not require any previous analyte extraction, filtration and preconcentration step, as in most methods described to date. Sample preparation is reduced to placing the olive oil sample in the vial. This reduces the analysis time and the experimental errors associated with this step of the analytical process. By using headspace generation, the volatiles of the sample are analysed without interference by the non-volatile matrix, and by using injection in solvent-vent mode at the PTV inlet, most of the compounds that are more volatile than filbertone are purged and the matrix effect is minimised. Use of a liner packed with Tenax-TA? allowed the compound of interest to be retained during the venting process. The limits of detection and quantification were as low as 0.27 and 0.83 μg/L, respectively, and precision (measured as the relative standard deviation) was 5.7%. The method was applied to the determination of filbertone in spiked olive oil samples and the results revealed the good accuracy obtained with the method.     

Application of dynamic liquid-phase microextraction and injection port derivatization combined with gas chromatography–mass spectrometry to the determination of acidic pharmaceutically active compounds in water samples

A method has been established for the determination of four pharmaceutically active compounds (ibuprofen, ketoprofen, naproxen and clofibric acid) in water samples using dynamic hollow fiber liquid-phase microextraction (HF/LPME) followed by gas chromatography (GC) injection port derivatization and GC–mass spectrometric (MS) determination. Dynamic HF/LPME is a novel approach to microextraction that involves the use of a programmable syringe pump to move the liquid phases participating in the extraction so as to facilitate the process. Trimethylanilinium hydroxide (TMAH) was used as derivatization reagent for the analytes to increase their volatility and improve chromatographic separation. Parameters that affect extraction efficiency (selection of organic solvent, volume of organic solvent, agitation in the donor phase, plunger movement and extraction time) were investigated. Under optimal conditions, the proposed method provided good enrichment factors up to 251, reproducibility ranging from 3.26% to 10.61%, and good linearity from 0.2 to 50 μg/L. The limits of detection ranged between 0.01 and 0.05 μg/L (S/N = 3) using selective ion monitoring. This method was applied to the determination of the four pharmaceutically active compounds in tap water and wastewater collected from a drain in the vicinity of a hospital.     

固相萃取-气相色谱-质谱法同时测定水中9种药品及个人护理用品

采用固相萃取-气相色谱-质谱联用技术,建立了水体中9种药品及个人护理用品（水杨酸、萘普生、布洛芬、对乙酰氨基酚、降固醇酸、三氯生、双氯酚酸、酮洛芬和双酚A）的定量分析方法。水样品经稀盐酸调节至pH=3后,采用Oasis HLB固相萃取小柱进行富集净化;选用三甲基氢氧化硫（TMSH）为衍生化试剂,在常温条件下对目标物进行快速甲基化;以气相色谱-质谱法选择离子监测模式（GC-MS-SIM）进行检测,由2,4,5-涕丙酸为内标进行定量分析。本实验分别对固相萃取和衍生化等前处理条件进行了系统的研究。在优化的实验条件下,方法的回收率为50.7~115.4%,相对标准偏差均不高于10%,检出限为0.03~0.30 μg/L,定量限为0.15~1.50 μg/L。利用该方法对东莞市某农田灌溉水进行了分析,4种目标物在样品中有检出,最大质量浓度范围为0.176~0.998 μg/L。结果表明该方法操作简便,灵敏可靠。     

Development of gas chromatography-mass spectrometry following headspace single-drop microextraction and simultaneous derivatization for fast determination of short-chain aliphatic amines in water samples

In this work, for the first time, gas chromatography-mass spectrometry (GC-MS) following headspace single-drop microextraction (HS-SDME) and simultaneous derivatization was developed for fast determination of short-chain aliphatic amines (SCAAs) in water samples. In the proposed method, SCAAs in water samples were headspace extracted and concentrated by suspending a microdrop of solvent, and SCAAs extracted in the microdrop of solvent were simultaneously and rapidly reacted with pentafluorobenzaldehyde (PFBAY). The formed SCAA derivatives were analyzed by GC-MS. The HS-SDME parameters of solvent selection, solvent volume, sample temperature, extraction time and stirring rate were studied, and the method linearity, precision and detection limits, were also studied. The results show that the proposed method provided good linearity (R(2)>0.99, 5.0-500 ng/ml), low detection limit (0.6-1.1 ng/ml), and good precision (RSD value less than 10%). The proposed method was further tested by its application to quantitative analysis of SCAAs in four wastewater samples. The experiment results have demonstrated that GC-MS following HS-SDME and simultaneous derivatization is a simple, rapid and low-cost method for the determination of SCAAs in water samples.     

Derivatization coupled to headspace programmed‐temperature vaporizer gas chromatography with mass spectrometry for the determination of amino acids: Application to urine samples

A new method based on headspace programmed‐temperature vaporizer gas chromatography with mass spectrometry has been developed and validated for the determination of amino acids (alanine, sarcosine, ethylglycine, valine, leucine, and proline) in human urine samples. Derivatization with ethyl chloroformate was employed successfully to determine the amino acids. The derivatization reaction conditions as well as the variables of the headspace sampling were optimized. The existence of a matrix effect was checked and the analytical characteristics of the method were determined. The limits of detection were 0.15–2.89 mg/L, and the limits of quantification were 0.46–8.67 mg/L. The instrumental repeatability was 1.6–11.5%. The quantification of the amino acids in six urine samples from healthy subjects was performed with the method developed with the one‐point standard additions protocol, with norleucine as the internal standard.     

全氟辛酸的3,4-二氯苯胺衍生化及高效液相色谱分析

介绍了一种可用于环境污染物全氟辛酸（PFOA）检测的高效液相色谱/紫外检测（HPLC/UV）分析方法。首先选用3,4-二氯苯胺为衍生化试剂,利用碳二亚胺法合成PFOA的酰胺化衍生产物（其在255 nm处紫外吸收最大）。然后确定四氢呋喃或水相介质中mg/L水平PFOA的衍生化条件及薄层硅胶色谱净化步骤。建立柱前衍生-HPLC/UV方法,以合成的全氟辛酸-3,4-二氯苯酰胺为对照品,外标法定量,PFOA上机测定的定量限为0.5 mg/L。通过加标回收试验评价方法的准确性,其中有机相及水相衍生法的回收率分别为91.8%~108.7%及40.1%~53.7%。与已报道的柱前衍生-HPLC/UV方法比较,本方法具有反应条件温和、衍生产物稳定、原料廉价易得、操作简单、成本低等优点。将本方法应用于光催化降解研究中PFOA的降解动力学实验,结果与液相色谱-质谱联用方法（LC/MS）的结果一致,说明本方法具有较好的应用前景。     

Headspace single-drop microextraction with in-drop derivatization for aldehyde analysis

A new technique, headspace single-drop microextraction (HS-SDME) with in-drop derivatization, was developed. Its feasibility was demonstrated by analysis of the model compounds, aldehydes in water. A hanging microliter drop of solvent containing the derivatization agent of O-2,3,4,5,6-(pentaflurobenzyl)hydroxylamine hydrochloride (PFBHA) was shown to be an excellent extraction, concentration, and derivatization medium for headspace analysis of aldehydes by GC-MS. Using the microdrop solvent with PFBHA, acetaldehyde, propanal, butanal, hexanal, and heptanal in water were headspace extracted and simultaneously derivatized. The formed oximes in the microdrop were analyzed by GC-MS. HS-SDME and in-drop derivatization parameters (extraction solvent, extraction temperature, extraction time, stirring rate microdrop volume, and the headspace volume) and the method validations (linearity, precision, detection limit, and recovery) were studied. Compared to liquid-liquid extraction and solid-phase microextraction, HS-SDME with in-drop derivatization is a simple, rapid, convenient, and inexpensive sample technique.     

Determination of pharmaceutical residues in waters by solid-phase extraction and large-volume on-line derivatization with gas chromatography-mass spectrometry

This work presents a modified method to analyze selected pharmaceutical residues (clofibric acid, ibuprofen, carbamazepine, naproxen, ketoprofen and diclofenac) in water samples. Various solid-phase extraction cartridges were investigated. The newly developed Oasis HLB (polystyrene-divinylbenzene-N-vinyl pyrrolidone terpolymer) solid-phase extraction (SPE) cartridge provides the optimal sample extraction results. The analytes were then identified and quantitatively determined by gas chromatography-mass spectrometry (GC-MS) via on-line derivatization in the injection-port using a large-volume (10 microl) sample injection with tetrabutylammonium (TBA) salts. This injection-port derivatization technique provides sensitivity, fast and reproducible results for pharmaceutical residues analysis. Mass spectra of butylated derivatives and tentative fragmentation profiles are proposed. Molecular ions and some characteristic ions were used as the quantitation ions to obtain maximum detection sensitivity and specificity. The quantitation limits of these compounds ranged from 1.0 to 8.0 ng/l in 500 ml tap water samples. Recovery of these residues in spiked various water samples ranged from 50 to 108% while RSD ranged from 1 to 10%. The selected analytes were detected in concentrations of 30 to 420 ng/l in wastewater treatment plant effluent and river water samples.     

Automated on-fiber derivatization with headspace SPME-GC-MS-MS for the determination of primary amines in sewage sludge using pressurized hot water extraction

An automated, environmentally friendly, simple, selective, and sensitive method was developed for the determination of ten primary aliphatic amines in sewage sludge at μg/kg dry weight (d.w.). The procedure involves a pressurized hot water extraction (PHWE) of the analytes from the solid matrix, followed by a fully automated on‐fiber derivatization with 2,3,4,5‐pentafluorobenzaldehyde (PFBAY) and headspace solid‐phase microextraction (HS‐SPME) and subsequent gas chromatography ion‐trap tandem mass spectrometry (GC‐IT‐MS‐MS) analysis. The limits of detection (LODs) of the method were between 0.5 and 45 μg/kg (d.w.) for all compounds except for ethyl‐, isopropyl‐, and amylamine, whose LODs were 70, 109, and 116 μg/kg (d.w.), respectively. The limits of quantification (LOQs) were between 10 and 350 μg/kg (d.w.). Repeatability and intermediate precision, expressed as RSD(%) (n=3), were lower than 18 and 21%, respectively. The method developed enabled to determine primary aliphatic amines in sludge from various urban and industrial sewage treatment plants as well as from a potable treatment plant. Most of the primary aliphatic amines were found in the sewage sludge samples analyzed corresponding to the maximum concentrations to the samples from the urban plant: for instance, isobutylamine and methylamine were found at 7728 and 12 536 μg/kg (d.w.), respectively. Amylamine was detected only in few samples but always at concentrations lower than its LOQ.     

Headspace-programmed temperature vaporizer-fast gas chromatography-mass spectrometry coupling for the determination of trihalomethanes in water

A new method based on the use of a headspace autosampler in combination with a GC equipped with a programmable temperature vaporizer (PTV) and an MS detector has been developed for the screening and quantitative determination of trihalomethanes (THMs) in different aqueous matrices. The use of headspace generation to introduce the sample has the advantage that no prior sample treatment is required, thus minimizing the creation of analytical artifacts and the errors associated with this step of the analytical process. The PTV inlet used was packed with Tenax-TA. The injection mode was solvent vent, in which the analytes are retained in the hydrophobic insert packing by cold trapping, while the water vapour is eliminated through the split line. This allows rapid injection of the sample in splitless mode, very low detection limits being achieved without the critical problem of initial sample bandwidth. The capillary column used allowed rapid separations with half-height widths ranging from 1.68 s (chloroform) to 0.66 s (bromoform). The GC run time was 7.3 min. The use of mass spectrometry allows the identification and quantification of the analytes at the low ppt level. The S/N ratio was at least 10-fold higher when the SIM mode was used in data acquisition as compared to the scan mode. The proposed method is extremely sensitive, with detection limits ranging from 0.4 to 2.6 ppt.     

分散液液微萃取-衍生化高效液相色谱-荧光检测法测定环境水样中4种酚类内分泌干扰物

为实现小体积环境水样中酚类化合物的准确、快速、高灵敏测定,通过分散液液微萃取(DLLME)和荧光衍生化的结合,建立了高效液相色谱-荧光检测(HPLC-FLD)双酚A、壬基酚、辛基酚和对特辛基酚的分析方法。考察并优化了DLLME和衍生化条件,结果表明,最优的DLLME条件为萃取剂氯仿用量70μL,分散剂乙腈用量400μL,漩涡振荡3 min,高速离心2 min。以2-[2-(7 H-二苯并[a,g]咔唑-乙氧基)]-乙基氯甲酸酯(DBCEC-Cl)为柱前衍生试剂,在pH10.5的Na2CO3-NaHCO3缓冲液/乙腈溶液、50℃下衍生反应3 min得到稳定的衍生产物,于10min内实现了4种酚衍生物的分离。方法的检出限为0.9~1.6 ng/L,定量限为3.8~7.1 ng/L,具有良好的线性、精密度和回收率,与以往报道的方法相比具有一定的优势和实用性,可用于造纸厂废水、湖水、生活废水、自来水中4种酚类内分泌干扰物的测定。     

Speciation of inorganic and tetramethyltin by headspace solid‐phase microextraction and gas chromatography–mass spectrometry

A headspace solid‐phase microextraction (HS‐SPME) method coupled to GC‐MS was developed in order to determine trace levels of tetramethyltin (TeMT) and inorganic tin (iSn) after ethylation to tetraethyltin (TeET) in various matrices. The derivatization of iSn and the extraction of both TeMT and iSn as TeET were performed in one step. Sodium tetraethylborate (NaBEt₄) was used as derivatization agent and the volatile derivatives were absorbed on a PDMS‐coated fused silica fiber. The conditions for the HS‐SPME procedure were optimized in order to gain in repeatability and sensitivity. Several critical parameters of GC‐MS were also studied. The detection of TeMT and iSn as TeET peaks was performed by the SIM mode. The precision of the proposed method is satisfactory providing RSD values below 10% for both tin species and good linearity up to 10 μg/L. The developed method was successfully applied to the determination of tin species in several samples like canned fish, fish tissues, aquatic plants, canned mineral water and sea water. The proposed HS‐SPME‐GC‐MS method was proved suitable to monitor the concentration levels of toxic tin compounds in environmental and biological samples.