Effect of precursor sol pH on microstructural, optical and photocatalytic properties of vacuum annealed zinc tin oxide thin films on glass

Dip coated vacuum annealed zinc tin oxide thin films on soda lime silica glass have been deposited from the precursor sols containing zinc acetate dihydrate and tin (IV) chloride pentahydrate (Zn:Sn = 67:33, atomic ratio in percentage) in 2-methoxy ethanol by varying sol pH (0.85–5.5). Crystallinity, morphology, optical and photocatalytic properties of the films strongly depend on sol pH. Measurement of grazing incidence X-ray diffraction confirms the presence of hexagonal nano ZnO in the films derived from the sols of pH < 5.5. Film crystallinity deteriorates on increasing sol pH and the film deposited from the sol of pH 5.5 shows XRD amorphous but the selected area diffraction pattern and HRTEM image evidence the presence of nano Zn₂SnO₄ (size, 5–6 nm). Direct band gap energy of films increases on increasing sol pH. To visualize the film surface microstructure, FESEM study has been done and a rod-like surface feature is revealed in the film deposited from the sol of pH 2.85. A dependence of precursor sol pH on the photocatalytic activity of films towards degradation of Rhodamine 6G dye under UV (254 nm) irradiation is found and the highest decomposition rate constant, ‘k’ value is obtained from the film prepared from the sol of pH 5.5. The presence of zinc deficient nano Zn₂SnO₄ in the film may consider for generating the highest ‘k’ value. We also measure gelling time, viscosity of sols as well as UV and FTIR studies on the films and propose chemical reactions.     

Glass formation and confined melting in sol–gel derived nano-ZnO aggregates

Sol–gel processing of ZnO nanocolloids has been revisited to prepare various alkaline metal acetate (MAc: K, Na, Li-acetates) containing ZnO nanopowders. Using differential scanning calorimetry and X-ray diffraction investigations, several new relationships between the morphology and the thermodynamic behavior in the aforementioned particulate ZnO/MAc nanocomposites were noticed: (1) large MAc melting depression shifts ?ΔT_m ~ 80 °C due to salt confinement within porous ZnO aggregates, (2) corresponding MAc crystallization and re-crystallization temperature depression shifts, (3) presence of multimodal pore size distributions within nanoaggregates and (4) glass formation at temperatures T_g between ?40 and 130 °C. We also note that the T_g value drops with rising alkaline metal size, increasing water content and decreasing ZnO particle size. In contrast, T_g rises in the case of co-doped Fe–LiAc/ZnO compositions.     

Sol–gel synthesis of ZnO–SiO2 thin films: impact of ZnO contents on its photonic efficiency

Highly crystalline ZnO–SiO₂ films obtained by a sol–gel method at different ZnO contents were deposited on silicon substrate (P(100)) using spin coating process. The XRD results revealed that the strong ZnO(100) peak is grown with highly c-axis oriented film and the crystallinity is progressively improved with increasing ZnO contents. SEM micrographs of the films deposited on silicon substrate show a homogeneous and uniformity structure at different ZnO content. The prepared ZnO–SiO₂ films are compared with either a film prepared from a commercial photocatalysts Hombikat UV-100 or Pilkington Glass Activ? by the determination of their photonic efficiencies for degradation of methylene blue. The photocatalytic efficiency of the 10 wt% ZnO–SiO₂ film was found to be about four times higher than film prepared from UV-100 or Pilkington Glass Activ?. The photocatalytic efficiencies of ZnO–SiO₂ films are increased with increasing ZnO content from 1 wt% to 10 wt% ZnO and then decreased at 15 wt% ZnO. The order of photocatalytic efficiencies of ZnO–SiO₂ films at different ZnO content and commercial photocatalysts after 6 h illumination were as following: 10 wt% ZnO > 15 wt% ZnO > 1 wt% ZnO > as-prepared 10 wt% ZnO–SiO₂ film > UV-100 > Pilkington Glass Activ?, which suggested that the ZnO–SiO₂ films are photoactive than commercial photocatalysts. The improved efficiency and potentially the low-cost synthesis suggest that this material might be practically useful as a photocatalyst film.     

4-Hydroxy-3,5-pyridinedicarboxylic Acids: Synthesis,Complexation Properties Towards Fe(III), Al(III), Cu(II), Zn(II), Human Serum Albumin,and Cellular Toxicity

4-hydroxy-3,5-pyridinedicarboxylic acid (DQ58) and 4-hydroxy-1-methyl-3,5-pyridinedicarboxylic acid (DQ71508) have been synthesized, and their Fe(III), Al(III), Cu(II), and Zn(II) coordination properties have been studied by potentiometry, UV–Vis spectroscopy (in the case of Fe(III), Al(III), Cu(II)), ¹H-NMR (for Al(III)) and EPR (for Cu(II)). The thermodynamic results were used to model the extent of the toxic metal ions decorporation (Fe(III) or Al(III)) in the presence of the essential metal ions (Cu(II) or Zn(II)). DQ58 and DQ71508 were demonstrated to interact with human serum albumin (HSA), which is assumed to be the main serum transporter of the chelators, and binding constants have been obtained by ultrafiltration. IC₅₀ values of 5.185 × 10^?3 and 1.033 × 10^?3 mol·L^?1 were collected after 24 and 48 h of treatment with DQ71508 towards human embryonic kidney HEK-293 cells, demonstrating the relatively low cytotoxicity of this compound. According to these results, both DQ58 and DQ71508 seem to be potential candidates for Fe chelation therapy, and DQ58 is a better Fe(III) chelator than DQ71508.     

ZnO nanoparticles and poly(acrylic) acid-based polymer gel electrolyte for photo electrochemical cell

This work presents a photo electrochemical cell based on zinc oxide (ZnO) nanoparticles and poly(acrylic) acid (PAA) doped with sodium iodide (NaI) and iodine (I₂) polymer gel electrolyte. The ZnO powders were synthesized by sol–gel storage and sol–gel centrifugation. The ZnO powder synthesized via sol–gel centrifugation showed the optimal structural properties, with largest crystallite sizes of 58 nm, average particles size between 20 and 80 nm and indirect band gap energy of 3.20 eV. The highest conductivity [(8.0 ± 0.1) × 10^?2 S cm^?1] was obtained for PAA + 0.8 M NaI + 0.02 M I₂. This sample achieved the lowest activation energy (0.029 eV) and electrochemical stability at 1.6 V. The ZnO powder synthesized via sol–gel centrifugation and PAA + 0.8 M NaI + 0.02 M I₂ was fabricated as a Cu–ZnO/PAA + 0.8 M NaI + 0.02 M I₂/C-ITO photo electrochemical cell.     

Preparation of single-phase α-Fe(III) oxide nanoparticles by thermal decomposition. Influence of the precursor on properties

In this research, we present an experimental procedure to prepare single-phase α-Fe(III) oxide nanoparticles by thermal decomposition of five different precursors including: iron(III) citrate; Fe(C₆H₅O₇), iron(III) acetylacetonate; Fe(C₅H₇O₂)₃, and iron(III) oxalate; Fe(C₂O₄)₃, iron(III) acetate; Fe(C₂H₃O₂)₃, and the thermal curves obtained were analyzed. The influence of the thermal decomposition of precursors on the formation α-Fe₂O₃ was studied by differential thermal gravimetry and thermogravimetry. The synthesized powders were characterized by using X-ray diffraction and scanning electron microscopy. High quality iron oxide nanoparticles with narrow size distribution and average particle size between ca. 2 and 30 nm have been obtained. It was found that the iron precursors affect the temperatures of the pure α-Fe₂O₃ nanoparticle formation with different diameters; iron(III) citrate (29 nm), iron(III) acetylacetonate (37 nm), and iron(III) oxalate (24 nm).     

Determination of Fe(II), Fe(III) and Fetotal in thermal water by ion chromatography spectrophotometry (IC-Vis)

Determination of iron speciation in water is one of the major challenges in environmental analytical chemistry. Here, we present and discuss a method for sampling and analysis of dissolved Fe(II), Fe(III), and Fe_total concentrations in natural thermal water covering a wide range of temperature, pH, chemical composition, and redox conditions. Various methods were tried in the collection, preservation, and storage of natural thermal water samples for the Fe(II) and Fe(III) determinations, yet the resultant Fe speciation determined was often found to be significantly affected by the methodology applied. Due to difficulties in preserving accurate Fe speciation in natural samples for later laboratory analysis, a field-deployed on-site method using ion-chromatography and spectrophotometry was developed and tested. The IC-Vis method takes advantage of ion chromatographic separation of Fe(II) and Fe(III), followed by post-column colour reaction and spectrophotometric detection, thus allowing analysis of Fe(II) and Fe(III) in a single 15-minute run. Additionally, Fe_total can be determined after sample oxidation. The analytical detection limits are ~2 µg L^?1 (LOD) using 200–1000 µL injection volumes and depend on the blank and reagent quality. The power of this method relies on the capability to directly determine a wide range of absolute and relative concentrations of Fe(II) and Fe(III) in the field. The field-deployed IC-Vis method was applied for the determination of Fe(II) and Fe(III) concentrations in natural thermal water with discharge temperatures ranging from 12°C to 95°C, pH between 2.46 and 9.75, and Fe_total concentrations ranging from a few μg L^?c up to 8.3 mg L^?1.     

Transparent conducting Sn:ZnO films deposited from nanoparticles

Homogeneous transparent conducting Sn:ZnO films on fused silica substrates were prepared by dip-coating from nanoparticle dispersions, while the nanocrystalline Sn:ZnO particles with different dopant concentrations were synthesized by microwave-assisted non-aqueous sol–gel process using Sn(IV) tert-butoxide and Zn(II) acetate as precursors and benzyl alcohol as solvent. The dopant concentration had a great impact on the electrical properties of the films. A minimum resistivity of 20.3 Ω cm was obtained for a porous Sn:ZnO film with initial Sn concentration of 7.5 mol% after annealing in air and post-annealing in N₂ at 600 °C. The resistivity of this porous film could further be reduced to 2.6 and 0.6 Ω cm after densified in Sn:ZnO and Al:ZnO reaction solution, respectively. The average optical transmittance of a 400-nm-thick Sn:ZnO film densified with Sn:ZnO after the two annealing steps was 91%.     

Solvent dependent growth of fibrous and non-fibrous nanocrystalline thin films of ZnO

Zinc oxide thin films were prepared from three different solvents using the sol–gel technique. Zinc acetate was used as the source of Zn, and the solvents ethanol, 2-methoxy ethanol and ethylene glycol were used to prepare the sols. ZnO thin films were deposited on glass microslides by pre-heating dip coated sol layers, following which they were finally annealed at 450 °C for half an hour. The films were characterized using structural, morphological and optical techniques. XRD studies show that the films grown from all the three solvents were single phase, highly oriented (along the c axis) ZnO having the wurzite structure. Optical transmission and photoluminescence spectra confirm the good quality of the ZnO films. SEM and AFM images show that the surfaces of the ZnO films, obtained using the first two (more volatile) solvents, consist of striations or ridges of height around 100–400 nm and are made up of nanoparticles 20–40 nm in size. The surfaces of the films produced from the less volatile third solvent are however smooth and devoid of striations although they are also covered with nanoparticles.     

Chelating behavior, thermal studies and biocidal efficiency of tioconazole and its complexes with some transition metal ions

New seven metal complexes of tioconazole drug with the general formulae [MCl₂(L)₂(H₂O)_x].yH₂O (where, x = 0 and y = 1 for M = Mn(II) or x = 2, y = 2 for M = Co(II)), and x = 0, y = 3 for M = Cu(II), Ni(II), Zn(II)) and [MCl₂(L)₂(H₂O)₂]Cl.3H₂O (where M = Cr(III) and Fe(III)) have been prepared and characterized based on elemental analyses, IR, magnetic moment, molar conductance, and thermal analyses techniques. From molar conductance data bivalent metal chelates are non-electrolytes while Cr(III) and Fe(III) chelates are electrolytes and of 1:1 type. According to the IR spectral data, TCNZ is coordinated to the metal ions in a neutral unidentate manner with N donor site of the imidazole–N. All the complexes are octahedral except Mn(II) complex has tetrahedral structure. TCNZ drug and its metal complexes were also screened for their biological activity.     

Synthesis, structures, and magnetic properties of carboxylate-bridged trinuclear complexes based on low-spin manganese(III)/iron(III) building blocks

Four linear trinuclear transition metal complexes have been prepared and characterized. The complexes [M^II(MeOH)₄][Fe^III(L)₂]₂·2MeOH (M = Fe (1) or Ni (2)), [Co^II(EtOH)₂(H₂O)₂][Fe^III(L)₂]₂·2EtOH (3), and [Mn^II(phen)₂][Mn^III(L)₂]₂·4MeOH (4) (H₂L = ((2-carboxyphenyl)azo)-benzaldoxime, phen = 1,10-phenanthroline) possesses a similar syn–anti carboxylate-bridged structure. The terminal Fe(III) or Mn(III) ions are low spin, and the central M(II) ions are high spin. Magnetic measurements show that antiferromagnetic interactions were present between the adjacent metal ions via the syn–anti carboxylate bridges. The antiferromagnetic coupling between low-spin Fe(III) and Ni(II) is unusual, which has been tentatively assigned to the structural distortion of Fe(III).     

CS‐Fe(II,III) complex as precursor for magnetite nanocrystal

Chitosan‐iron ions complex (CS‐Fe(II,III) complex) was used as precursor to synthesize magnetite nanocrystals and the mechanism was discussed. The magnetite nanocrystals have diameters of about 10 nm and clusters were formed due to slight aggregation of several magnetite nanocrystals. FT‐IR and X‐ray photoelectron spectrometer (XPS) investigations indicated that the Fe(II) and Fe(III) were chelated by ? NH₂ and ? OH groups of chitosan in CS‐Fe(II,III) complex, and the molar ratio of ? NH₂/Fe(II,III) was approximately 2. This chelation effect destroyed the hydrogen bonds of chitosan. In the following alkali treatment process, the chelated Fe(II) and Fe(III) provided nucleation site and formed the magnetite nanocrystals. After alkali treatment, the chelation effect between iron ions and ? NH₂ groups disappeared and some kind of weak interaction formed between magnetite and ? NH₂ groups. Moreover, the ? OH groups of chitosan have an interaction with the synthesized magnetite nanocrystals. Copyright © 2010 John Wiley & Sons, Ltd.     

Modifications in band gap and optical properties of Zn0.96−xNd0.04CuxO (x = 0, 0.05, 0.1 and 0.15) nanoparticles

Nd-doped and Nd, Cu co-doped ZnO nanoparticles (Zn_0.96?xNd_0.04Cu_xO, x = 0, 0.05, 0.1 and 0.15) were synthesized by sol–gel method. The structural and optical properties of the samples were investigated by X-ray diffraction (XRD) and UV–visible photo-spectrometer. The synthesized nanoparticles have different microstructure without changing a hexagonal wurtzite structure. CuO phase was noticed in XRD spectra at 38.73° after Cu = 5 % which was formed from remaining un-reacted Cu²⁺ ions. The average crystal size was gradually increased from Cu = 0 % (17 nm) to 15 % (17.6 nm) having lowest value (16.7 nm) at Cu = 5 %. The change in lattice parameters confirmed the substitution of Cu in Zn–Nd–O lattice. The observed constant c/a ratio revealed that there was no change in hexagonal wurtzite structure by Cu-doping. The energy dispersive X-ray spectra confirmed the presence of appropriate amount of Nd and Cu in Zn–O lattice. The optical absorption was increased gradually from Cu = 0–10 % and showed maximum at Cu = 10 % due to the presence of more nucleation centres and defect states. The defects related green band between 487 and 493 nm was due to the oxygen vacancies and intrinsic defects. The higher transmittance (≈ 90 %) noticed at Cu = 15 % leads to the industrial applications. The observed blue shift in energy gap from 3.49 eV (Cu = 0 %) to 3.65 eV (Cu = 10 %) and the red shift from Cu = 10 % (3.65 eV) to Cu = 15 % (3.61 eV) can be explained by the Burstein–Moss effect. Presence of chemical bonding was confirmed by Fourier transform infrared spectra.     

Rapid speciation of trace iron in rainwater by reverse flow injection analysis coupled to a long path length liquid waveguide capillary cell and spectrophotometric detection

A method for speciation and determination of low levels of dissolved iron in rainwater was established by coupling reverse flow injection analysis with a 2-m liquid waveguide capillary cell and spectrophotometric detection. Ferrozine solution was injected into a sample stream to form an Fe(II)-ferrozine complex with Fe(II), and the absorbance of this complex was detected at both 562 nm and 625 nm with a reference wavelength at 700 nm. Fe(III) was analyzed in the same manner after being reduced to Fe(II) by ascorbic acid. The optimum conditions and the interference of Cu(I), Ni(II) and Co(II) were investigated. The limits of detection were 0.1 nM for Fe(II) and 0.2 nM for Fe(III), while the linear ranges were 0.4 – 200 nM for Fe(II) and 0.8 – 287 nM for Fe(III) at 562 nm, and can be extended to higher concentrations with the detection at a less sensitive wavelength of 625 nm. The sample throughput was 6 h^?1, and the total sample volume consumed was 10 mL. This method has been successfully applied to analyze dissolved iron in rainwater of Xiamen from August to November, 2008. The lowest level of iron in rainwater was observed during typhoon events. By adopting reverse flow injection analysis coupled with liquid waveguide long path length capillary cell, the reagent consumption was low and the sensitivity was enhanced. The other advantages of this method are high sample throughput, wide linear dynamic range and high selectivity for Fe(II).     

Monodisperse superparamagnetic nanoparticles by thermolysis of Fe(III) oleate and mandelate complexes

Monodisperse superparamagnetic iron oxide nanoparticles of controlled size were synthesized by thermal decomposition of organic iron compounds in different high-boiling solvents in the presence of oleic acid and/or oleylamine. The compounds included Fe(III) oleate and mandelate, formed from FeCl₃ and the respective acids. The size of the nanoparticles was easily tuned to 8–27 nm by varying the experimental conditions. The nanoparticles were characterized using X-ray diffraction (XRD), transmission electron microscopy (TEM), and magnetization measurements. The hydrophobic coating of the particles was analyzed by thermogravimetric analysis (TGA) and atomic absorption spectroscopy (AAS). To make the particles biocompatible and water dispersible, nontoxic hydrophilic poly(ethylene glycol) derivatives were synthesized and used for phase transfer of hydrophobic particles into water using a ligand-exchange procedure.     

Electrodeposition and stripping voltammetry of arsenic(III) and arsenic(V) on a carbon black–polyethylene composite electrode in the presence of iron ions

In this work, a new sensor is proposed for the stripping voltammetric determination (anodic stripping voltammetry—ASV) of total arsenic(V) or arsenic(III). The sensor is based on an Fe-modified carbon composite electrode containing 30 % carbon black–high-pressure polyethylene (CB/PE). The modification with iron is achieved by the addition of Fe(III) or Fe(II) ions to the sample solution and co-electrodeposition of iron and arsenic on the CB/PE electrode. In anodic stripping voltammetry, two peaks are observed: an Fe peak at ?0.45 or ?0.29 V and a peak at 0.12?±?0.07 V which depends on the arsenic concentration and corresponds to the As(0) → As(III) oxidation, as is the case with other solid electrodes. The optimum conditions proposed for ASV determination of As(V) and As(III) in solutions in the presence of dissolved oxygen are the following: the background electrolyte is 0.005 M HCl containing 0.5–1 mg/?L Fe(III) for As(V) and containing 1.0–1.5 mg/?L Fe(III) for As(III), respectively; E _dep?=??2.3 V; rest period at ?0.10 V for 3–5 s before the potential sweep from ?0.2 to +0.4 V; scan rate is 120 mV/?s. The detection limit (LOD, t?=?120 s) for As(III) and As(V) is 0.16 and 0.8 μg/?L, respectively. Various hypotheses on the effect of Fe ions and atoms on the electrodeposition and dissolution of arsenic are considered. The new method of determination of As(III) and As(V) differs from known analogues by its simplicity, low cost, and easy accessibility of the electrode material. It allows the voltammetric determination of total arsenic after chemical reduction of all its forms to As(III) or after their oxidation to As(V).     

Sensor Performance of Nanostructured TiO<Subscript>2</Subscript>–SnO<Subscript>2</Subscript> Films Prepared by an Aqueous Sol–Gel Process

Nanostructured TiO₂–SnO₂ thin films and powders were prepared by a facile aqueous particulate sol–gel route. The prepared sols showed a narrow particle size distribution with hydrodynamic diameter in the range 17.2–19.3 nm. Moreover, the sols were stable over 5 months, since the constant zeta potential was measured during this period. The effect of Sn:Ti molar ratio was studied on the crystallisation behaviour of the products. X-ray diffraction analysis revealed that the powders were crystallised at the low temperature of 400 °C containing anatase-TiO₂, rutile-TiO₂ and cassiterite-SnO₂ phases, depending on annealing temperature and Sn:Ti molar ratio. Furthermore, it was found that SnO₂ retarded the anatase to rutile transformation up to 800 °C. The activation energy of crystallite growth was calculated in the range 0.96–6.87 kJ/mol. Transmission electron microscope image showed that one of the smallest crystallite sizes was obtained for TiO₂–SnO₂ binary mixed oxide, being 3 nm at 600 °C. Field emission scanning electron microscope analysis revealed that the deposited thin films had nanostructured morphology with the average grain size in the range 20–40 nm at 600 °C. Thin films produced under optimized conditions showed excellent microstructural properties for gas sensing applications. They exhibited a remarkable response towards low concentrations of CO gas at low operating temperature of 200 °C, resulting in increased thermal stability of sensing films as well as a decrease in their power consumption.     

Influence of sodium dodecyl sulfate on the fabrication of zinc oxide nanoparticles

Dispersive ZnO nanoparticles with a primary particle size of about 70 nm and an average agglomerate size of about 2.0 ??m were synthesized via the precipitation-thermal decomposition route using ZnSO₄ and Na₂CO₃ as the reactants and sodium dodecyl sulfate (SDS) as the surface modification agent. The presence of minor amounts of SDS in the formation of hydrozicite (Zn₅(CO₃)₂(OH)₆) precursor changed the agglomeration size of ZnO from 9.7 to 2.0 ??m and the primary particle size of ZnO from about 45 to 70 nm. Molecular simulation based on the DISCOVER model and COMPASS force field indicated that SDS was adsorbed on the surface of Zn₅(CO₃)₂(OH)₆ mainly via the coulomb and hydrogen bond interactions.     

Synthesis and characterization of magnetic nanoparticles

Magnetic nanoparticles with average diameter in the range of 6.4-8.3 nni have been synthesized by a chemical co-precipitation of Fe(Ⅱ)and Fe(Ⅲ)salts in 1.5 M NH4OH solution.The size of the magnetic particles is dependent on both temperature and the ionic strength of the iron ion solutions.The magnetic particles formed at higher temperature or lower ionic strength were slightly larger than those formed at lower temperature or higher ionic strength respectively.In spite of the different reaction conditions,all the resultant nanoparticles are nearly spherical and have a similar crystalline structure.At 300 K,such prepared nanoparticles are superparam-agnetic.The saturation magnetizations for 7.8 and 6.4 nm particles are 71 and 63 emu/g respectively,which are only ~ 20-30% less than the saturation magnetization(90 emu/g)of bulk Fe3O4 Our results indicated that a control of the reaction conditions could be used to tailor the size of magnetic nanoparticles in free precipitation.     

Preparation of CuFe2O4/SiO2 nanocomposite starting from Cu(II)–Fe(III) carboxylates embedded in hybrid silica gels

Nanocomposites of the type 30 % CuFe₂O₄/70 % SiO₂ were synthesized using the modified sol–gel method starting from tetraethylorthosilicate, metal nitrates (Fe(NO₃)₃·9H₂O, Cu(NO₃)₂·3H₂O) and the diol: 1,3-propane diol. The obtained hybrid gel, which contains within the pores, the metal nitrates and diol, was thermally treated at 140 °C, when the redox reaction between metal nitrates and 1,3-propane diol takes place forming Cu(II)–Fe(III) carboxylate compounds of malonate type. The thermal decomposition of the carboxylates within the gels pores, at ~300 °C, leads to simple or mixed metal oxides, uniformly distributed within the amorphous silica matrix. The spinel system CuFe₂O₄/SiO₂ was obtained starting with 700 °C. The evolution of the spinel phase with the annealing temperature was investigated and resulted that at 1,000 °C, the matrix crystallizes into cristobalite and quartz. The formation of bulk CuFe₂O₄, starting from the same type of Cu(II)–Fe(III) carboxylate compounds was also investigated. A comparison between the thermal evolution of bulk CuFe₂O₄ and CuFe₂O₄/SiO₂ starting from Cu(II)–Fe(III) carboxylate compounds was made. The magnetic behavior of the ferrite nanocrystallites depending on the annealing temperature was also investigated.