Enhanced adsorption performance of a novel Fe‐Mn‐Zr metal oxide nanocomposite adsorbent for anionic dyes from binary dye mix: Response surface optimization and neural network modeling

A novel adsorbent, Fe‐Mn‐Zr metal oxide nanocomposite was synthesized and investigated for removal of methyl orange (MO) and eosin yellow (EY) dyes from binary dye solution. The magnetic nanocomposite has shown surface area of 143.01 m²/g and saturation magnetization of 15.29 emu/g. Optimization was carried out via response surface methodology (RSM) for optimizing process variables, and optimum dye removal of 99.26% and 99.55% were obtained for MO and EY dye, respectively with contact time 62 min, adsorbent dose 0.45 g/l, initial MO concentration 11.0 mg/l, and initial EY concentration 25.0 mg/l. A feed forward back propagation neural network model has shown better prediction ability than RSM model for predicting MO and EY dye removal (%). Adsorption process strictly follows Langmuir isotherm model, and enhanced adsorption capacities of 196.07 and 175.43 mg/g were observed for MO and EY dye, respectively due to synergistic effects of physicochemical properties of trimetal oxides. Surface adsorption and pore diffusions are the mechanisms involved in the adsorption as revealed from kinetic studies.     

Synthesis and characterization of CDs/Al2O3 nanofibers nanocomposite for Pb2+ ions adsorption and reuse for latent fingerprint detection

This study reports a new approach of preparation of carbon dots coated on aluminum oxide nanofibers (CDs/Al₂O₃NFs) nanocomposite and reusing the spent adsorbent of lead (Pb²⁺) ions loaded adsorbent (Pb²⁺-CDs/Al₂O₃NFs) nanocomposite for latent fingerprint detection (LFP) after removing Pb²⁺ ions from aqueous solution. CDs/Al₂O₃NFs nanocomposite was prepared by using CDs and Al₂O₃NFs with adsorption processes. The prepared nanocomposite was then characterized by using UV–visible spectroscopy (UV–visible), Fourier transforms infrared spectroscopy (FTIR), Fluorescence, X-ray diffraction pattern (XRD), scanning electron microscope (SEM), Transmission electron microscopy (TEM), Energy-dispersive X-ray spectroscopy (EDS), Zeta potential, X-ray photoelectron spectroscopy (XPS). The average size of the CDs was 51.18 nm. The synthesized CDs/Al₂O₃NFs nanocomposite has proven to be a good adsorbent for Pb²⁺ ions removal from water with optimum pH 6, dosage 0. 2 g/L. The results were best described by the Freundlich Isotherm model. The adsorption capacity of CDs/Al₂O₃NFs nanocomposite showed the best removal of Pb²⁺ ions with q_m = (177. 83 mg/g), when compared to the previous reports. This adsorption followed the pseudo-second order kinetic model. ΔG and ΔH values indicated spontaneity and the endothermic nature of the adsorption process. CDs/Al₂O₃NFs nanocomposite therefore showed potential as an effective adsorbent. The data were observed from adsorption–desorption after 6 cycles which showed good adsorption stability and re- usability of CDs/Al₂O₃NFs nanocomposite. Furthermore, the spent adsorbent of Pb²⁺-CDs/Al₂O₃NFs nanocomposite has proven to be sensitive and selective for LFP detection on various porous substrates. Hence Pb²⁺-CDs/Al₂O₃NFs nanocomposite can be reused as a good fingerprint labelling agent in LFP detection so as to avoid secondary environmental pollution by disposal of the spent adsorbent.     

Rapid removal of anionic organic dye from contaminated water using a poly(3-aminobenzoic acid/graphene oxide/cobalt ferrite) nanocomposite low-cost adsorbent via adsorption techniques

This research study aims to remove hazardous anionic azo dyes (Congo red (CR)) from aqueous solutions via a simple adsorption method using a poly(3-aminobenzoic acid/graphene oxide/cobalt ferrite) nanocomposite (P3ABA/GO/CoFe₂O₄) as a novel and low-cost nanoadsorbent, as synthesized by a simple and straightforward polymerization method. Typically, 3-aminobenzoic acid (3ABA), as monomer, was chemically polymerized with graphene oxide (GO) and cobalt ferrite (CoFe₂O₄) in an aqueous acidic medium containing an ammonium persulfate initiator. The adsorbent P3ABA/GO/CoFe₂O₄ nanocomposite was characterized using various techniques such as Fourier transform infrared spectroscopy, X-ray diffraction, thermogravimetric analysis, transmission electron microscopy, scanning electron microscopy, energy-dispersive analysis by X-ray and Brunauer–Emmett–Teller, vibrating sample magnetometer, and zeta potential techniques. These techniques confirmed the interaction between the poly(3-aminobenzoic acid) with GO and CoFe₂O₄ due to the presence of π-π interactions, hydrogen bonding, and electrostatic forces. Herein, the removal efficiency of dye from aqueous solution by the adsorbent was studied according to several parameters such as the pH of the solution, dye concentration, dosage of adsorbent, contact time, and temperature. The adsorption of the dye was fitted using a Langmuir model (R² between 0.9980 and 0.9995) at different temperatures, and a kinetic model that was pseudo-second order (R² = between 0.9993 and 0.9929) at various initial concentrations of CR dye. In addition, the data revealed that the P3ABA/GO/CoFe₂O₄ nanocomposite exhibited a high adsorption capacity (153.92 mg/g) and removal for CR dye (98 %) at pH 5. Thermodynamic results showed the adsorption process was an endothermic and spontaneous reaction. It was found that, in terms of reusability, the P3ABA/GO/CoFe₂O₄ adsorbent can be used for up to six cycles. In this study, P3ABA/GO/CoFe₂O₄ nanocomposites were found to be low cost, and have an excellent removal capability and fast adsorption rate for CR from wastewater via a simple adsorption method. Moreover, this adsorbent nanocomposite could be simply separated from the resultant solution and recycled.     

Fe3O4-CuO-activated carbon composite as an efficient adsorbent for bromophenol blue dye removal from aqueous solutions

Dye wastewater from industries is posing tremendous health hazards. The lethal dyes can be eliminated using nanomaterials and scientific approach like adsorption which is facile, cheap, safe as well as ecofriendly. Fe₃O₄-CuO-AC composite was prepared by a hydrothermal method and used for the removal of dyes in wastewater. The composite material was characterized by various techniques such as XRD, SEM, EDS, TEM and FT-IR. The Fe₃O₄-CuO-AC composite was used to treat five types of dyes in water. Fe₃O₄-CuO-AC composite showed the highest adsorption capability for bromophenol blue (BPB) dye. The effects of initial concentration, pH, the amount of adsorbent and temperature were also studied. The optimum conditions were found to be 20 ppm dye concentration, pH 9, an adsorbent dose of 0.06 gL^─1 at 65 °C. A removal efficiency of 97% was obtained for BPB dye during 120 min of adsorption. Kinetic studies indicated that a pseudo-second order is the most suitable model for the adsorption process. The Fe₃O₄-CuO-AC composite showed better adsorption capacity as compare to Fe₃O₄-AC except for the Methyl green dye. The maximum adsorption capacity was found to be 88.60 mg/g for BPB. Additionally, the thermodynamic parameters (ΔS°, ΔH° and ΔG°) showed that the process was spontaneous and exothermic. All the above results revealed that the Fe₃O₄-CuO-AC compositecan be an effective adsorbent for removing dyes from wastewater.     

Adsorption of cationic methylene blue dye using microwave-assisted activated carbon derived from acacia wood: Optimization and batch studies

This study assesses the performance of optimized acacia wood-based activated carbon (AWAC) as an adsorbent for methylene blue (MB) dye removal in aqueous solution. AWAC was prepared via a physicochemical activation process that consists of potassium hydroxide (KOH) treatment, followed by carbon dioxide (CO₂) gasification under microwave heating. By using response surface methodology (RSM), the optimum preparation conditions of radiation power, radiation time, and KOH-impregnation ratio (IR) were determined to be 360 W, 4.50 min, and 0.90 g/g respectively, which resulted in 81.20 mg/g of MB dye removal and 27.96% of AWAC’s yield. Radiation power and IR had a major effect on MB dye removal while radiation power and radiation time caused the greatest impact on AWAC’s yield. BET surface area, mesopore surface area, and pore volume of optimized AWAC were found to be 1045.56 m²/g, 689.77 m²/g, and 0.54 cm³/g, respectively. Adsorption of MB onto AWAC followed Langmuir and pseudo-second order for isotherm and kinetic studies respectively, with a Langmuir monolayer adsorption capacity of 338.29 mg/g. Mechanism studies revealed that the adsorption process was controlled by film diffusion mechanism and indicated to be thermodynamically exothermic in nature.     

Multifunctional Zn0.3Al0.4O4.5 crystals: An efficient photocatalyst for formaldehyde degradation and EBT adsorption

The Zn_0.3Al_0.4O_4.5 nanoparticles (ZnAlONPs) with size of 70–90 nm are used as an efficient photocatalyst for formaldehyde (HCHO) degradation and effective adsorbent for the removal of eriochrome black-T (EBT) dye from synthetic aqueous solution. Degradation of HCHO reactions were studied using TiO₂ (homemade), TiO₂ (P-25) and ZnAlONPs by irradiating under 18 W daylight lamp source for photocatalytic degradation. The HCHO degradation rate is about 67, 76 and 89% for TiO₂ (homemade), TiO₂ (P25) and ZnAlONPs during 2 h reaction, respectively at initial formaldehyde gas concentration of 20 ppm. Maximum adsorption capacity was optimized by changing the parameters such as pH, EBT concentration and adsorbent dosage. A  200 mg of ZnAlONPs are useable for quick removal of EBT (>95%). Langmuir isotherm model showed a maximum adsorption capacity of 90.90 mgg⁻¹. The ZnAlONPs could be successfully reused upto 5^th adsorption/desorption cycle for EBT dye removal from water samples.     

Novel Fe3O4/hydroxyapatite/β‐cyclodextrin nanocomposite adsorbent: Synthesis and application in heavy metal removal from aqueous solution

The increased global concern on environmental protection has made researchers focus their attention on new and more efficient methods of pollutant removal. In this research, novel nanocomposite adsorbents,i.e., magnetic hydroxyapatite (Fe₃O₄@HA) and magnetic hydroxyapatite β‐cyclodextrin (Fe₃O₄@HA‐CD) were synthesized and used for heavy metal removal. The adsorbents were characterized by FTIR, XRD, TGA, VSM, and SEM. In order to investigate the effect of β‐cyclodextrin (β‐CD) removal efficiency, adsorption results of nine metal ions were compared for both adsorbents. β‐CD showed the most increasing effect for Cd²⁺ and Cu²⁺ removal, so these two ions were selected for further studies. The effect of diverse parameters including pH, contact time, initial metal ion concentration and adsorbent dosage on the adsorption process was discussed. The optimum pH was 6 and adsorption equilibrium was achieved after 1 hr. Adsorption kinetic data were well fitted by pseudo‐second‐order model proposing that metal ions were adsorbed via chemical reaction. Adsorption isotherm was best described by the Langmuir model, and maximum adsorption capacity for Cd²⁺ and Cu²⁺ was 100.00 and 66.66 (mg/g), respectively. Desorption experiment was also done, and the most efficient eluent used for desorption of metal ions was EDTA (0.001 M) with 91% and 88% of Cd²⁺ and Cu²⁺ release, respectively. Recyclability studies also showed a 19% decrease in the adsorption capacity of the adsorbent after five cycles of regeneration. Therefore, the synthesized adsorbents were recognized as potential candidates for heavy metal adsorption applications.     

Poly(butyl methacrylate)-grafted alginate/Fe3O4 nanocomposite: Synthesis and its application for removal of dyes

This study involved the utilization of a free radical-graft copolymerization reaction for the development of a novel adsorbent, namely, poly(butyl methacrylate)-grafted alginate/Fe₃O₄ nanocomposite (PBMA-gft-Alg/Fe₃O₄). Transmission electron microscopy, scanning electron microscopy, energy-dispersive X-ray analysis, X-ray diffraction patterns analysis, and Fourier transform infrared spectroscopy (FT-IR) were carried out for the characterization of Fe₃O₄ NPs and PBMA-gft-Alg/Fe₃O₄ nanocomposites. The capability of nanocomposites and nanoparticles to adsorb dyes such as MG and MB, resulting in their removal from aqueous media, was evaluated under different conditions such as pH, temperature, contact time, and dose of adsorbent. Optimum parameters for adsorption of dyes were found to be pH of 10, 50°C, contact time of 180 min, and 0.2 g of adsorbent. Efficiency of the PBMA-gft-Alg/Fe₃O₄ nanocomposite was found to be significantly greater than that of Fe₃O₄ NPs for eliminating the desired dye. Langmuir, Freundlich, Sips, and Temkin models were used for testing the experimental data. Freundlich model was the one that best described the adsorption.     

Ultrasound-aided rapid and enhanced adsorption of anionic dyes from binary dye matrix onto novel hematite/polyaniline nanocomposite: Response surface methodology optimization

In recent times, polyaniline (PANI), a conducting polymer, has been studied widely for environmental remediation application due to its controllable electric conductivity with high surface area, which makes it a suitable adsorbent material. But lower mechanical stability of PANI is considered to be a serious drawback for its large-scale industrial application. To improve the mechanical strength of PANI, in this study, hematite nanoparticles were impregnated onto PANI by oxidative polymerization method in order to fabricate a novel organometallic nanocomposite (hematite-PANI-NC). The hematite-PANI-NC was used as adsorbent for removal of methyl orange (MO) and eosin yellow (EY) dye from binary dye matrix under ultrasonic-assisted adsorption. Excellent MO and EY dye removal (more than 98%) was observed from binary matrix at a wide solution pH from 2.0 to 6.0, and under ultrasound wave the adsorption equilibrium was achieved within 15 min only. Both MO and EY dyes adsorption experimental data strictly followed Langmuir isotherm, and maximum monolayer adsorption capacity of 126.58 mg/g and 112.36 mg/g was observed for MO and EY dye, respectively. The uptake mechanism of MO and EY dyes onto hematite-PANI-NC is governed by electrostatic interaction, π-π bonding and hydrogen bonding between dye molecules and nanocomposite. Response surface methodology analysis reveals maximum MO and EY removal of 98.43% and 99.35% at optimum experimental conditions. This study implies that the hybrid organometallic material hematite-PANI-NC has high potential for quick and enhanced sono-assisted uptake of anionic dyes from water near neutral solution pH.     

Anchoring H3PW12O40 on aminopropylsilanized spinel‐type cobalt oxide (Co3O4‐SiPrNH2/H3PW12O40): A novel nanohybrid adsorbent for removing cationic organic dye pollutants from aqueous solutions

In this work, phosphotungstic acid (H₃PW₁₂O₄₀; PW₁₂) was chemically anchored on aminopropylsiloxane functionalized spherical Co₃O₄ nanoparticles (Co₃O₄–SiPrNH₂) and the resultant nanocomposite (Co₃O₄–SiPrNH₂/PW₁₂) was fully characterized. The results demonstrated successful anchoring of PW₁₂ on the surface of Co₃O₄–SiPrNH₂nanoparticles. The Co₃O₄–SiPrNH₂/PW₁₂ nanohybrid indicated a specific surface area of 42.14 m² g^?1, which was greater than that of pure PW₁₂ (ca. 5 m² g^?1). The adsorption efficiency of this novel adsorbent nanomaterial was evaluated for removing methylene blue (MB), rhodamine B (RhB) and methyl orange (MO) dyes from aqueous solutions. The hybrid nanomaterial exhibited a high adsorption rate and selective adsorptivity for the cationic MB and RhB dyes compared to those for anionic MO dye. The prepared hybrid nanomaterial removed over 98% of MB within 12 min. The effects of initial pH, contact time, adsorbent dosage, and temperature were investigated on the adsorption process. The adsorption capacity of nanohybrid for cationic MB dye was 38.46 mg g^‐1. Also, adsorption kinetics indicated that the adsorption by Co₃O₄–SiPrNH₂/PW₁₂ was well‐modeled using pseudo‐second‐order kinetic model. Finally, thermodynamic parameters revealed that the adsorption was endothermic and spontaneous. The adsorption rate and ability of the Co₃O₄–SiPrNH₂/PW₁₂ were enhanced as compared with Co₃O₄ and Co₃O₄–SiPrNH₂ samples due to enhanced electrostatic attraction intraction. The nanohybride was easily separated and reused without any change in structure. Thus, it could be a promising green adsorbent for removing organic pollutants in water.     

Green synthesis of copper oxide nanoparticles CuO NPs from Eucalyptus Globoulus leaf extract: Adsorption and design of experiments

The study is concerned with synthesizing copper oxide nanoparticles with leaf extract Eucalyptus Globoulus. The results of scanning electron microscopy (SEM) and dynamic light scattering (DLS) revealed that the green synthesized copper oxide nanoparticles are spherical and have a mean particle size of 88 nm, with a negative zeta potential of ?16.9 mV. The XRD graph showed the crystalline and monoclinic phases of CuO nanoparticles. The average crystalline size around 85.80 nm was observed by the Debye–Scherrer formula. The adsorption characteristics of the nano-adsorbents were investigated using methyl orange, and the adsorption efficiency at room temperature attained 95 mg/g. Copper oxide nanoparticles (CuO NPs) adsorb methyl orange dye most effectively at pH 4.5 when the dye is applied in quantities of 0.04 g/50 mL. Box–Behnken design (BBD) in response surface methodology (RSM) was used to optimize various process parameters, such as pH solution (X₁: 2 – 11), adsorbing dose (X₂: 0.01 – 0.08 g/L), [MO] dye concentration (X₃: 10 – 80 mg/L). Overall, the adjusted coefficient of determination (R²) value of 0.99 demonstrated that the used model was quite appropriate, and the chosen RSM was effective in optimization the decolorization conditions of MO.     

Synthesis of nano‐sized magnetite mesoporous carbon for removal of Reactive Yellow dye from aqueous solutions

In this study, core‐shell structures of magnetite nanoparticles coated with CMK‐8 ordered mesoporous carbon (Fe₃O₄@SiO₂‐CMK‐8 NPs) have been successfully synthesized for the first time by carbonizing sucrose inside the pores of the Kit‐6 mesoporous silica. The nano‐sized mesoporous particles were characterized by X‐ray diffraction, Fourier transform‐infrared spectroscopy, scanning electron microscope, dynamic light scattering, vibrating‐sample magnetometer, Brunauer–Emmett–Teller (BET) and transmission electron microscopy instruments. The obtained nanocomposite was used for removal of Reactive Yellow 160 (RY 160) dye from aqueous samples. The N₂ adsorption–desorption method (at 77 K) confirmed the mesoporous structure of synthesized Fe₃O₄@SiO₂‐CMK‐8 NPs. Also, the surface area was calculated by the BET method and Langmuir plot as 276.84 m²/g and 352.32 m²/g, respectively. The surface area, volume and pore diameter of synthesized nanoparticles (NPs) were calculated from the pore size distribution curves using the Barrett–Joyner–Halenda formula (BJH). To obtain the optimum experimental variables, the effect of various experimental parameters on the dye removal efficiency was studied using Taguchi orthogonal array experimental design method. According to the experimental results, about 90.0% of RY 160 was removed from aqueous solutions at the adsorbent amount of 0.06 g, pH 3 and ionic strength = 0.05 m during 10 min. The pseudo‐second order kinetic model provided a very good fit for the RY 160 dye removal (R² = 0.999). The Langmuir, Freundlich, Temkin and Dubinin–Radushkevich models were applied to describe the equilibrium isotherms, and the Langmuir isotherm showed the best fit to data with the maximum adsorption capacity of 62.893 mg/g. Furthermore, the Fe₃O₄@SiO₂‐CMK‐8 NPs could be simply recovered by external magnet, and exhibited recyclability and reusability for a subsequent six runs.     

Removal of cibacron blue 3G-A (CB) dye from aqueous solution using chemo-physically activated biochar from oil palm empty fruit bunch fiber

A novel biodegradable adsorbent called pyrolysed empty fruit bunch fibres (PEF) was prepared by chemo-physical activation of empty fruit bunch fibres (EFB) biochar for removal of cibacron blue 3G-A (CB) dye from aqueous solution. PEF was characterized using FTIR, SEM-EDX, XRD and BET techniques. The N₂ adsorption-desorption isotherms indicated PEF’s surface area to be 362.84 m²g⁻¹ and XRD attributed amorphous nature to PEF. After adsorption process, PEF has smoother surface morphology, increase in carbon by weight and shift in functional groups. The established adsorption optimum conditions were pH 10, 45 min contact time and 0.10 g/100 mL adsorbent dosage with 99.05% CB dye removal capacity at 343 K and initial dye concentration 100 mg/L. Desorption ratio >90% after seventh cycle of adsorption-desorption experiments confirmed high reusability (regeneration) of PEF. Pseudo second order kinetic and Freundlich were better fitted with kinetic and isotherm model respectively, while mechanism of adsorption was controlled by film diffusion (external mass transfer). Thermodynamic studied revealed ΔG, ΔS and ΔH to be −3.12 MJ/mol K, 9.11 kJ/mol K, 6.83 kJ/mol respectively at 343 K. The negative value of ΔG, positive values of ΔS and ΔH indicated spontaneity, feasibility and endothermic nature of CB dye adsorption from aqueous solution onto PEF.     

Nanostructured spinel-type M(M = Mg,Co, Zn)Cr2O4 oxides: novel adsorbents for aqueous Congo red removal

Nanostructured spinel-type M(M = Mg, Co, Zn)Cr₂O₄ oxides with novel adsorbents for aqueous Congo red removal were synthesized by a polyacrylamide gel method and studied for their phase structure, microstructure, adsorption performance, and multiferroic behavior. The phase structure and purity analysis revealed that the nanostructured spinel-type M(M = Mg, Co, Zn)Cr₂O₄ oxides presented a spinel-type cubic structure, and the formation of a secondary phase such as Cr₂O₃, MgO, ZnO, or Co₃O₄ was not observed. The microstructure characterization confirmed that the spinel-type MCr₂O₄ oxides grew from fine spherical particles to large rhomboid particles. Adsorption experiments of spinel-type MCr₂O₄ oxides for adsorption of Congo red dye were fitted well with the pseudo-second-order kinetics. The adsorption capacity of the ZnCr₂O₄ oxide (44.038 mg/g, pH 7, temperature 28 °C, initial dye concentration 30 mg/L) was found to be higher than that of MgCr₂O₄ oxide (43.592 mg/g, pH 7, temperature 28 °C) and CoCr₂O₄ oxide (28.718 mg/g, pH 7, temperature 28 °C). The effects of initial adsorbent concentration, initial dye concentration, pH, and temperature between the ZnCr₂O₄ oxide and Congo red dye at which optimal removal occurs, were performed. The thermodynamic studies confirmed that a high temperature favors the adsorption of Congo red dye onto ZnCr₂O₄ oxide studied. The nanostructured spinel-type M(M = Mg, Co, Zn)Cr₂O₄ oxides that exhibited high adsorption performance for adsorption of Congo red dye can be ascribed to the synergistic effect of electrostatic interaction, pore filling, and ion exchange. The present work suggested that the nanostructured spinel-type M(M = Mg, Co, Zn)Cr₂O₄ oxides have excellent adsorption performance and multiferroic behavior, which shows potential applications for removal of the Congo red dye from wastewater, magnetic memory recording media, magnetic sensor, energy collection and conversion device, and read/write memory.     

Modeling and Optimization of Adsorption Removal of Reactive Orange 13 on the Alginate–Montmorillonite–Polyaniline Nanocomposite via Response Surface Methodology

In this work, an alginate–montmorillonite–polyaniline (Alg–MMT–PANI ) nanocomposite (NC) was synthesized and applied for the adsorptive removal of reactive Orange 13 (RO13 ) as a model azo dye compound. The Alg–MMT–PANI NC was prepared by the polymerization of aniline in the presence of Alg–MMT hybrid through in situ polymerization. The optimization and modeling of the removal process was carried out using the response surface methodology (RSM ) based on central composite design (CCD ). Important parameters influencing the adsorption removal of RO13 , including the initial concentration of RO13 , pH , adsorbent dose, and contact time, were selected as input variables for RSM . Furthermore, the adsorption kinetic studies revealed that the experimental data best fitted with a pseudo‐second‐order model. Additionally, adsorption isotherm studies revealed that the obtained data were well fitted to the Langmuir isotherm model and, accordingly, the maximum adsorption capacity, q_m , was obtained at level of 111.111 mg/g.     

Synthesis and performance evaluation of chitosan/zinc oxide nanocomposite as a highly efficient adsorbent in the removal of reactive red 198 from water

In this study, Chitosan and Chitosan-zinc oxide (ZnO) nanocomposite were prepared and applied as a low-cost adsorbent with high adsorption capacity for removing reactive red 198 (RR 198) dye from contaminated water. After preparation, it was characterized using FT-IR, XRD, and SEM. The effect of pH, temperature, time, adsorbent amount, and initial dye concentration were investigated in the removal efficiency of RR 198. The maximum adsorption capacity (q_m) obtained from the Langmuir equation was 172.41 mg/g in adsorbent dose of 0.1 g/L, pH: 4, temperature of 25°C, adsorption time of 40 min. The thermodynamic parameters demonstrated the spontaneous and endothermic nature of the adsorption process. Due to the high efficiency of chitosan/ZnO nanocomposite in removal of RR 198 from water and advantages such as high adsorption capacity, simple synthesis, and easy application, it can be used as an effective method in the removal of RR 198 from water.     

Magnetic Fe3O4/ZIF-8 optimization by Box-Behnken design and its Cd(II)-adsorption properties and mechanism

In this study, the preparation of magnetic Fe₃O₄/ZIF-8 (MFZ) and its adsorption properties for Cd(II) from water were investigated. Various characterizations demonstrate that the as-prepared MFZ has well magnetic-separation performance and thermal stability. In batch adsorption tests, the effects of pH, initial concentration, and adsorbent dosage were evaluated. According to the findings, when the pH is 7 and the dosage is 150 mg/L, the adsorption capacity for a 40 mg/L Cd(II) solution reaches 102.3 mg/g in 180 min. The Cd(II) adsorption processes was found to correspond to pseudo-first-order kinetics and Langmuir model according to the adsorption kinetics and isotherms. The Langmuir model predicted a maximal saturation adsorption capacity of 160.26 mg/g at 298 K. Thermodynamic analysis revealed that the Cd(II) adsorption is an endothermic, spontaneous process. Ion exchange, coordination reaction, and electrostatic interaction are all involved in Cd(II) adsorption by MFZ. The optimum conditions for Cd(II) adsorption were proposed and confirmed in accordance with the results of the response surface optimization experiments. Furthermore, regeneration tests demonstrate the great repeated regeneration ability of MFZ. According to the anticipated production cost, treating wastewater with a Cd(II) concentration of 40 mg/L would cost roughly US$ 8.35/m³. MFZ showed good potential for Cd(II) removal from water.     

Highly efficient removal of toxic lead ions from aqueous solutions using a new magnetic metal‐organic framework nanocomposite

A magnetic metal‐organic framework (MOF) nanocomposite was successfully prepared by a new and green strategy through reasonable design. Magnetic MOF of Fe₃O₄‐NHSO₃H@HKUST‐1 nanocomposite use for removal of lead ions as an environmental pollutant. The experimental results indicated that the nano adsorbent of Fe₃O₄‐NHSO₃H@HKUST‐1 can removed lead ions under optimum operational conditions. The dosage of the nanocomposite, pH of the sample solution, and contact time were obtained to be 10 mg, 7.0, and 90 min, respectively, while the initial concentration of Pb(II) ions of 400 mg/L was used. A kinetic study indicated that a pseudo‐second‐order model agreed well with the experimental data. The isotherm experiments revealed that the Langmuir model attained better fits to the equilibrium data than the Freundlich model. The maximum adsorption capacity of the adsorbent for the removal of lead under the optimum operational conditions of pH 7.0 and temperature 25°C was found to be 384.6 mg/g. The thermodynamic parameters indicate that the adsorption of lead is spontaneous and endothermic. The magnetic MOF nanocomposite could be recovered easily and reused many times without significant loss of its nano‐adsorbent activity. The proposed method is simple, eco‐friendly, low cost, and efficient in the removal of lead ions from aqueous solutions.     

Adsorptive removal of malachite green and Rhodamine B dyes on Fe3O4/activated carbon composite

This study demonstrates the adsorption experiments of toxic dyes malachite green (MG) and Rhodamine B (RB) on Fe₃O₄-loaded activated carbon (AC). AC, which is known to be a high-capacity adsorbent, was aimed to be easily separated from aqueous media by loading it with Fe₃O₄. Fe₃O₄-loaded AC was prepared by the coprecipitation method and named magnetic activated carbon (M-AC), and the produced M-AC was characterized by x-ray diffraction (XRD), thermogravimetric analysis (TGA), and pH_pzc analyses. MG and RB adsorption by the M-AC was performed separately by batch technique and the effects of adsorbent amount, solution pH, and initial dye concentration on the adsorption were explored. Maximum removal efficiencies were found to be 96.11% for MG and 98.54% for RB, and the Langmuir isotherm model was the most fitted isotherm model for the adsorption. The kinetic and thermodynamic studies showed that the adsorption proceeded via the pseudo-second-order kinetic model and endothermic in-nature for both dyes.