Oxidation of ethylbenzene to styrene oxide in the presence of cellulose‐supported Pd magnetic nanoparticles

Palladium and Fe₃O₄ nanoparticles were deposited on N‐(2‐aminoethyl)acetamide‐functionalized cellulose for use in a catalytic reaction. The catalyst was characterized using Fourier transform infrared spectroscopy, thermogravimetric analysis, X‐ray diffraction, energy‐dispersive X‐ray analysis and transmission electron microscopy, and applied in the oxidation reaction of ethylbenzene at 100 °C using H₂O₂. Styrene oxide was obtained as the sole product of the oxidation reaction during 24 h. This reaction has some advantages such as one‐pot transformation of ethylbenzene to styrene oxide, high yield, excellent selectivity and magnetically recoverable catalyst. Also, the recovered catalyst could be used in the oxidation reaction four times without decrease in yield. Copyright © 2016 John Wiley & Sons, Ltd.     

金催化一氧化碳氧化反应中锌锡复合氧化物的载体效应

氧化物负载的纳米金催化剂对CO氧化反应具有极高的活性,这不仅依赖于金的结构特性,也取决于氧化物载体的结构.近年来,除了氧化硅、氧化铝等惰性载体以及氧化钛、氧化铈、氧化铁等可还原性载体外,人们还致力于探索各类新型氧化物载体.另一方面,锡酸锌是具有反尖晶石结构的化合物,并且在透明导电氧化物、锂离子电池阳极材料、光电转换装置以及传感器等方面应用广泛.然而,迄今为止,锡酸锌仍未被用于负载纳米金催化剂,因此相关的构效关系作用研究也十分有限.基于此,本文采用氮气吸附-脱附实验、电感耦合等离子体原子发射光谱(ICP-AES)、X射线衍射(XRD)、X射线光电子能谱(XPS)、透射电子显微镜(TEM)和高分辨电镜(HRTEM)、高角环形暗场像-扫描透射电子显微镜(HAADF-STEM)、X射线吸收精细结构谱(XAFS)和氢气程序升温脱附(H2-TPD)等手段,系统研究了锡酸锌负载的纳米金催化剂在CO氧化反应中催化性能差异的原因.首先,利用水热法制备了锡酸锌(ZTO)载体,而其织构性质可由碱(N2H4·H2O)与金属离子(Zn2+)的比例在4/1(ZTO_1)、8/1(ZTO_2)和16/1(ZTO_3)之间进行调节.结果发现, ZTO_2具有最大的孔体积(0.223 cm3/g)和最窄的孔径分布.再采用沉积沉淀法将0.7 wt% Au负载于其上,得到金-锡酸锌(Au_ZTO)催化剂. ICP-AES测得样品中Au含量在0.57-0.59 wt%,与投料比接近. CO氧化反应结果显示, Au_ZTO_1和Au_ZTO_2的表观活化能相同,但后者的活性更高;而Au_ZTO_3在220°C以下没有活性,催化性能最差,与纯锡酸锌载体相当. XRD结果显示,反应过程中ZTO晶相、晶胞参数及晶粒尺寸变化不明显; TEM和HRTEM分析表明,载体ZTO在反应前后均为多面体形貌,平均颗粒尺寸在12-16 nm; XPS结果验证了Zn2+和Sn4+离子是新鲜和反应后样品中载体金属的存在形式; HAADF-STEM探测到所有样品中均含有1-2 nm的Au粒子; XAFS结果表明, Au以Au0形式存在,并且在Au_ZTO_3中Au平均粒径大于4 nm,而其它两样品约为2 nm. H2-TPR结果表明,金的引入对ZTO载体耗氢量影响不大,但还原峰温度向低温移动;金属-载体相互作用强弱与催化活性高低具有正相关性,即Au_ZTO_2> Au_ZTO_1>> Au_ZTO_3.这是由于不同织构性质的锡酸锌载体对于纳米金活性物种的稳定作用不同所致,具有最大孔体积和最窄孔径分布的ZTO_2负载的金纳米颗粒表现出最高活性.     

Iron oxide on carbon‐based supports as efficient catalysts for organic compounds oxidation

For the first time, iron oxide on carbon aerogel, amine functionalized carbon nanotube, black carbon and carboxylic acid functionalized carbon nanotube in the presence of H₂O₂ was reported as an efficient and stable catalyst for the selective oxidation of sulfides and alcohols. The catalysts were characterized by scanning electron microscopy, energy‐dispersive spectroscopy, transmission electron microscopy, X‐ray photoelectron spectroscopy, X‐ray diffraction, Fourier transform infrared spectroscopy and atomic absorption spectroscopy. In the next step, catalytic reactivity toward sulfide to sulfoxide and alcohol to aldehyde/ketone oxidation in the presence of H₂O₂ was studied and discussed.     

Au/ZrLa掺杂 CeO2催化剂在CO氧化反应中优异的催化活性：锆镧协同作用

在过去的25年,纳米金催化剂上 CO氧化反应得到广泛研究,但始终没有一致的结论。这是因为影响纳米金催化活性的因素很多,包括金的价态、载体的性质、氧空位、金属与载体之间的相互作用等,尤其是各影响因素之间相互牵制,增加了催化反应机理的研究难度。氧化铈载体表面氧缺陷的浓度较高,有利于活性金属组分在其表面的稳定和分散,因此氧化铈纳米晶负载的 Au催化剂受到广泛关注。此外,当 CeO2晶格中部分 Ce被化学性质不同的其它元素取代后,可以促进 CeO2晶格氧的活化,提高氧的储放能力,从而有利于催化反应进行。因此,本文采用水热法合成了组成均匀的 CeO2, CeZrOx和 CeZrLaOx三个载体,并通过沉淀-沉积法负载金。利用 X射线衍射(XRD)、拉曼光谱(Raman)、X射线光电子能谱(XPS)、高分辨透射电镜(HRTEM)、X射线吸收精细结构(XAFS)和氢气程序升温还原(H2-TPR)等技术分析了催化剂的物相结构、表面性质、形貌以及金纳米颗粒的大小和价态等性质,并结合其在 CO氧化反应中催化性能的差异,探讨影响金催化剂活性的关键因素。 XRD, TEM, HRTEM和 XAFS结果表明,三个载体上所得金纳米颗粒的平均尺寸都在2–4 nm,且分散较好; XPS结果表明,影响催化剂活性的关键因素不是金的价态,而是载体表面的活性氧物种。从Raman结果可知,掺杂后的氧化铈载体上氧空位浓度明显增加,因而催化剂活性都有所提高。 H2-TPR进一步探讨了三个载体以及负载金后其氧化还原能力的变化,结果表明,金和载体之间的相互作用可以增强载体的氧化还原性能以及表面氧空位浓度,进一步提高了催化剂活性,而负载金催化剂氧化还原性能的变化与载体的组成密切相关。由于锆的掺杂可使金与载体之间相互作用减弱,而镧则增强了二者间相互作用,因此 Au/CeZrLaOx催化剂上锆和镧的协同掺杂作用使其表面活性氧物种浓度最高,低温时表现出最高的催化活性。     

Nanosized nickel oxide particles and modification with poly(methyl methacrylate)

In recent years, there is an increasing interest in the fabrication of inorganic–organic materials considering the remarkable change and improvement in properties. In this investigation, nanosized nickel oxide (NiO) particles were first prepared by calcination of nickel hydroxide precursor obtained by a simple liquid‐phase process. Mixed phases of NiO and nickel hydroxide were present as the calcination temperature was lower than 250°C. Non‐stoichiometric NiO was formed between 250°C and 350°C, and a pure NiO was obtained as the temperature reached 500°C. The surface characteristics of NiO particles were evaluated by measuring the adsorption behavior of anionic and cationic surfactants and some biomolecules. NiO/poly(methyl methacrylate) composite particles were then prepared using variable NiO/methyl methacrylate (MMA) ratio by seeded emulsion polymerization. The efficiency of NiO incorporation in the composite increased as the MMA content was increased in the recipe. The composite particles were colloidally stable, and the obtained particles were characterized by Fourier transform infrared, scanning electron microscopy, X‐ray diffraction, and X‐ray photoelectron spectra. Copyright © 2011 John Wiley & Sons, Ltd.     

A generalized technique for the encapsulation of nano‐sized NiO particles by styrene‐2‐hydroxyethyl methacrylate copolymer

Encapsulation of nickel oxide (NiO) particles is of great interest to the researchers as such modification produces remarkable improvement in properties and versatility in application potential. In this investigation, nanosized NiO particles were first prepared by calcination of nickel hydroxide precursor obtained using a simple liquid‐phase process. The produced NiO particles were stabilized with oleic acid and then treated with tetraethylorthosilicate to produce NiO/SiO₂ composite seed particles. Finally tri‐layered inorganic/organic composite particles were prepared by seeded copolymerization of styrene and 2‐hydroxyethyl methacrylate (HEMA) in the presence of NiO/SiO₂ composite seed particles. The produced composite particles named as NiO/SiO₂/P(S‐HEMA) were colloidally stable, and the obtained particles were characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, X‐ray diffraction, X‐ray photoelectron spectroscopy and thermogravimetric analyses. Copyright © 2015 John Wiley & Sons, Ltd.     

Sensing and photocatalytic properties of nanosized Cu(I)CN organotin supramolecular coordination polymer based on pyrazine

Orange prismatic crystals of the supramolecular coordination polymer (SCP) _∞³[Cu(CN)₂(Me₃Sn)(Pyz)], SCP 1 , were synthesized using a self‐assembly method under ambient conditions. Nanosized 1 was obtained using the same molar ratio in water by ultrasonic irradiation. SCP 1 was characterized using single‐crystal X‐ray diffraction, elemental analysis, thermal analysis and Fourier transform infrared spectroscopy. SCP 1 and its nanosized 1 particles were also examined using powder X‐ay diffraction and scanning electron microscopy. The luminescence emission of SCP 1 was studied as well as its use as a sensor for the detection of common organic solvents and metal ions. Also, the catalytic activities of nanosized 1 towards various organic dyes were investigated under ambient conditions, UV irradiation and ultrasonic irradiation. Nanosized 1 as a heterogeneous nanoparticle catalyst exhibits high catalytic activity for the degradation of eosin‐Y and acid blue dyes. The mechanism of degradation investigated using various scavenger techniques is proposed and discussed. The catalytic oxidation process is mainly caused by ?OH radicals.     

Preparation of rhodium catalysts on laminar and zeolitic structures by anchoring of organometallic rhodium

Rhodium catalysts supported on six different aluminosilicate structures were prepared by hydrogen reduction of a cationic organometallic rhodium complex anchored to the support. The precursor active phase was incorporated in acetone medium through ion exchange using [Rh(Me₂CO)_x(NBD)]ClO₄ as the metal precursor species, in which NBD is 2,5‐norbornadiene and (Me₂CO)_x is acetone. The effect of the structure and characteristics of the support on metal load and dispersion was studied in the heterogeneous catalysts thus prepared. The supports were characterized by X‐ray diffraction, energy‐dispersive X‐ray analysis, volumetric adsorption and surface acidity. For the precursors and catalysts, the metal load was determined by UV–VIS spectra, the reduction temperature was determined by differential scanning calorimetry, and rhodium dispersion was measured by chemisorption. The structure of the materials used as supports had a great influence on the catalyst prepared. A higher metal content was achieved in the supports with laminar structures, whereas better dispersion was shown by the catalysts supported on zeolitic structures. Copyright © 2001 John Wiley & Sons, Ltd.     

Zirconium oxide complex‐functionalized MCM‐41 nanostructure: an efficient and reusable mesoporous catalyst for oxidation of sulfides and oxidative coupling of thiols using hydrogen peroxide

Zirconium oxide complex‐functionalized mesoporous MCM‐41 (Zr‐oxide@MCM‐41) as an efficient and reusable catalyst is reported for the oxidation of sulfides into sulfoxides using hydrogen peroxide (H₂O₂) as the oxidant, with short reaction times in good to excellent yields at room temperature under solvent‐free conditions. Also, a simple and efficient method is reported for the oxidative coupling of thiols into corresponding disulfides in good to high yields using H₂O₂ as oxidant in the presence of Zr‐oxide@MCM‐41 as recoverable catalyst in ethanol at room temperature. A series of sulfides and thiols possessing functional groups was successfully converted into corresponding products. After completion of reactions the catalyst was easily separated with simple filtration from the reaction mixture and reused for several consecutive runs without significant loss of catalytic efficiency. The mesoporous catalyst was characterized using Fourier transform infrared spectroscopy, Brunauer–Emmett–Teller surface area measurements, X‐ray diffraction, transmission and scanning electron microscopies, energy‐dispersive X‐ray spectroscopy and thermogravimetric analysis. Copyright © 2015 John Wiley & Sons, Ltd.     

Nickel−Copper bimetallic mesoporous nanoparticles: As an efficient heterogeneous catalyst for N‐alkylation of amines with alcohols

A bimetallic catalyst (Ni/Cu‐MCM‐41) is prepared via co‐condensation method. The latter is characterized by Fourier transform infrared (FT‐IR), X‐ray powder diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X‐ray spectroscopy (EDX), diffuse reflectance spectroscopy (DRS), and nitrogen adsorption–desorption analysis. Catalytic performance of Ni/Cu‐MCM‐41 is probed in N‐alkylation of amines with alcohols through a hydrogen autotransfer process. Noteworthy, this catalytic system appears very efficient for synthesis of a range of secondary and tertiary amines in good to excellent isolated yields. Moreover, the catalyst is successfully recovered and reused four times without notable decrease in its activity.     

Ionic liquid functionalized graphene oxide for enhancement of styrene‐butadiene rubber nanocomposites

Ionic liquid 1‐allyl‐3‐methyl‐imidazolium chloride (AMICl) is used to fine‐tune the surface properties of graphene oxide (GO) sheets for fabricating ionic liquid functionalized GO (GO‐IL)/styrene‐butadiene rubber (SBR) nanocomposites. The morphology and structure of GO‐IL are characterized using atomic force microscope, X‐ray diffraction, differential scanning calorimetry, X‐ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, UV‐vis spectra and Raman spectra. The interaction between GO and AMICl molecules as well as the effects of GO‐IL on the mechanical properties, thermal conductivity and solvent resistance of SBR are thoroughly studied. It is found that AMICl molecules can interact with GO via the combination of hydrogen bond and cation–π interaction. GO‐IL can be well‐dispersed in the SBR matrix, as confirmed by X‐ray diffraction and scanning electron microscope. Therefore, the SBR nanocomposites incorporating GO‐IL exhibit greatly enhanced performance. The tensile strength, tear strength, thermal conductivity and solvent resistance of GO‐IL/SBR nanocomposite with 5 parts per hundred rubber GO‐IL are increased by 505, 362, 34 and 31%, respectively, compared with neat SBR. This method provides a new insight into the fabrication of multifunctional GO‐based rubber composites. Copyright © 2016 John Wiley & Sons, Ltd.     

Preparation of a monolith functionalized with zinc oxide nanoparticles and its application in the enrichment of fluoroquinolone antibiotics

This study describes the enrichment ability of ZnO‐modified methacrylic acid‐co‐ethylene dimethacrylate polymer monoliths as stationary phases for the simultaneous determination of antibiotics (ofloxacin, ciprofloxacin, enoxacin, and pefloxacin) combined with high‐performance liquid chromatography. The prepared monolith was characterized by scanning electron microscopy, X‐ray photoelectron spectroscopy, Fourier‐transformed infrared spectroscopy, and thermogravimetric analysis. The polymer monolith microextraction method has been applied to the enrichment of fluoroquinolone antibiotics and satisfactory results were obtained in the analysis of water samples. Compared with the conventional methacrylic acid based monolith, the developed monolith exhibited a higher enrichment capacity because of the introduction of zinc oxide into the preparation process.     

Synthesis of Pyranopyrazoles Using Magnetically Recyclable Heterogeneous Iron Oxide‐silica Core‐shell Nanocatalyst

The Fe₃O₄@SiO₂ core‐shell nanocatalyst were prepared and efficiently used for four‐component coupling reaction of aromatic aldehydes, malononitrile, ethyl acetoacetate and hydrazine hydrate in water/ethanol mixture. Various aromatic aldehydes possessing electron‐withdrawing and electron‐donating groups in different positions on the ring were successfully transformed to substituted pyranopyrazoles in high yields in short time. The nanocatalyst was easily recovered, and reused five times without significant loss in cata‐ lytic activity and performance. The structure, size and morphology of the nanosized catalyst were studied by various techniques such as Fourier transform infrared spectroscopy, powder X‐ray diffraction, dynamic light scattering and transmission electron microscopy.     

Copper(I) oxide nanoparticles supported on magnetic casein as a bio‐supported and magnetically recoverable catalyst for aqueous click chemistry synthesis of 1,4‐disubstituted 1,2,3‐triazoles

Copper(I) oxide nanoparticles supported on magnetic casein (Cu₂O/Casein@Fe₃O₄NPs) has been synthesized as a bio‐supported catalyst and was characterized using powder X‐ray diffraction, transmission electron microscopy, energy dispersive X‐ray and Fourier transform infrared spectroscopies, thermogravimetric analysis and inductively coupled plasma optical emission spectrometry. The catalytic activity of the synthesized catalyst was investigated in one‐pot three‐component reactions of alkyl halides, sodium azide and alkynes to prepare 1,4‐disubstituted 1,2,3‐triazoles with high yields in water. The reaction work‐up is simple and the catalyst can be magnetically separated from the reaction medium and reused in subsequent reactions.     

Copper Oxide Nanoparticle Modified Sol–Gel‐Derived Carbon Ceramic by Microwave Irradiation,and Its Application for Determination of Adenine at Very Low Potential

In this work the copper oxide nanoparticles simultaneous with sol–gel‐derived carbon ceramic production were synthesized and doped in ceramic by microwave irradiation in a few minutes without using any catalyst and organic solvent. The ceramic composition was characterized by X‐ray diffraction (XRD), X‐ray photoelectron spectroscopy (XPS) and Fourier transforms infrared (FT‐IR), and its surface morphology was investigated by scanning electron microscopy (SEM). The proposed ceramic with detection limit of 0.1 µM, was used for electrocatalytic determination of adenine at potential about 700 mV lower than its usual oxidation potential.     

Anchoring calcium carbonate on graphene oxide reinforced with anticorrosive properties of composite epoxy coatings

Calcium carbonate nanoparticles (nano‐CaCO₃) anchored graphene oxide (GO) sheet nanohybrids (GO‐CaCO₃) are fabricated, and their structure can be measured by scanning electron microscope, transmission electron microscopy, X‐ray photoelectron spectroscopy, X‐ray diffraction and Fourier‐transform infrared spectroscopy analysis. Afterwards, composite epoxy coatings, filled with GO and GO‐CaCO₃ nanohybrids, are prepared via a curing process. The dispersion and anticorrosive properties of composite epoxy coatings are investigated. The results reveal that GO‐CaCO₃ nanohybrids achieve a homogeneous dispersion as well as reinforce corrosion resistance of epoxy coatings. Furthermore, the anticorrosive mechanisms are tentatively proposed for the GO‐CaCO₃/epoxy coatings. Copyright © 2016 John Wiley & Sons, Ltd.     

Morphology and crystal structure of the poly(ethylene oxide)–hydroquinone molecular complex

The occurrence of a molecular complex between poly(ethylene oxide) (PEO) and p‐dihydroxybenzene (hydroquinone) has been determined using different experimental techniques such as differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction (WAXD), and Fourier transform infrared spectroscopy (FTIR). From DSC investigations, an ethylene oxide/hydroquinone molar ratio of 2/1 was deduced. During the heating, the molecular complex undergoes a peritectic reaction and spontaneously transforms into a liquid phase and crystalline hydroquinone (incongruent melting). A triclinic unit cell (a = 1.17 nm, b = 1.20 nm, c = 1.06 nm, α = 78°, β = 64°, γ = 115°), containing eight ethylene oxide (EO) monomers and four hydroquinone molecules, has been determined from the analysis of the X‐ray diffraction fiber patterns of stretched and spherulitic films. The PEO chains adopt a helical conformation with four monomers per turn, which is very similar to the 7₂ helix of the pure polymer. A crystal structure is proposed on the basis of molecular packing considerations and X‐ray diffraction intensities. It consists of a layered structure with an alternation of PEO and small molecules layers, both layers being stabilized by an array of hydrogen bonds. The morphology of PEO–HYD crystals was studied by small angle X‐ray scattering and DSC. As previously shown for the PEO–resorcinol complex, PEO–HYD samples crystallize with a lamellar thickness corresponding to fully extended or integral folded chains. The relative proportion of lamellae with different thicknesses depends on the crystallization temperature and time. Finally, the observed morphologies are discussed in terms of intermolecular interactions and chain mobility. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1197–1208, 1999     

Electrocatalytic Activity of Nanocomposites of Sulphur Doped Graphene Oxide and Nanosized Cobalt Phthalocyanines

In this work we explore the electrocatalytic activity of nanocomposites of reduced sulphur doped graphene oxide nanosheets (rSDGONS) and cobalt phthalocyanine (CoPc) or cobalt tetra amino phthalocyanine (CoTAPc) towards hydrogen peroxide. Transmission electron microscopy, scanning electron microscopy, X‐ray photon spectroscopy, X‐ray diffraction, chronoamperometry, linear scan voltammetry and cyclic voltammetry were used to characterize the nanocomposites. Nanosized CoPc showed superior (in terms of currents) electrocatalytic oxidation and reduction of hydrogen peroxide compared to CoTAPc nanoparticles (CoTAPc NP ). The lowest detection limit was obtained for hydrogen peroxide oxidation on electrodes modified with CoPc NP ‐rSDGONS at 1.49 µM. The same electrode gave a high adsorption equilibrium constant of 1.27×10³ mol^?1 and a Gibbs free energy of ?17.71 kJ/mol, indicative of a spontaneous reaction on the electrode surface.     

Transition Metal (Mn,Fe, Co,Ni)‐Doped Graphene Hybrids for Electrocatalysis

The development of electrocatalysts is crucial for renewable energy applications. Metal‐doped graphene hybrid materials have been explored for this purpose, however, with much focus on noble metals, which are limited by their low availability and high costs. Transition metals may serve as promising alternatives. Here, transition metal‐doped graphene hybrids were synthesized by a simple and scalable method. Metal‐doped graphite oxide precursors were thermally exfoliated in either hydrogen or nitrogen atmosphere; by changing exfoliation atmospheres from inert to reductive, we produced materials with different degrees of oxidation. Effects of the presence of metal nanoparticles and exfoliation atmosphere on the morphology and electrocatalytic activity of the hybrid materials were investigated using electron microscopy, energy‐dispersive X‐ray spectroscopy, X‐ray photoelectron spectroscopy, and cyclic voltammetry. Doping of graphene with transition metal nanoparticles of the 4th period significantly influenced the electrocatalysis of compounds important in energy production and storage applications, with hybrid materials exfoliated in nitrogen atmosphere displaying superior performance over those exfoliated in hydrogen atmosphere. Moreover, nickel‐doped graphene hybrids displayed outstanding electrocatalytic activities towards reduction of O₂ when compared to bare graphenes. These findings may be exploited in the research field of renewable energy.     

Functionalized graphene oxide supported copper (I) complex as effective and recyclable nanocatalyst for one‐pot three component synthesis of 1,2,3‐triazoles

Efficient, one pot three‐component reaction of alkyl halides, sodium azide with terminal alkynes can be catalyzed by functionalized graphene oxide with copper(I) under thermal conditions. A series of 1,4‐disubstituted 1,2,3‐triazoles were obtained by this one‐pot strategy. The catalyst was prepared and characterized by Fourier transform infrared spectroscopy (FT‐IR), X‐ray diffraction (XRD), emission scanning electron microscopy (FE‐SEM) and energy dispersive X‐ray (EDX). The catalyst can be reused at least five times without significant deactivation.