One‐pot synthesis of magnetic zeolitic imidazolate framework/grapheme oxide composites for the extraction of neonicotinoid insecticides from environmental water samples

Magnetic zeolitic imidazolate framework 67/graphene oxide composites were synthesized by one‐pot method at room temperature for the first time. Electrostatic interactions between positively charged metal ions and both negatively charged graphene oxide and Fe₃O₄ nanoparticles were expected to chemically stabilize magnetic composites to generate homogeneous magnetic products. The additional amount of graphene oxide and stirring time of graphene oxide, Co²⁺, and Fe₃O₄ solution were investigated. The zeolitic imidazolate framework 67 and Fe₃O₄ nanoparticles were uniformly attached on the surface of graphene oxide. The composites were applied to magnetic solid‐phase extraction of five neonicotinoid insecticides in environmental water samples. The main experimental parameters such as amount of added magnetic composites, extraction pH, ionic strength, and desorption solvent were optimized to increase the capacity of adsorbing neonicotinoid insecticides. The results show limits of detection at signal‐to‐noise ratio of 3 were 0.06–1.0 ng/mL under optimal conditions. All analytes exhibited good linearity with correlation coefficients of higher than 0.9915. The relative standard deviations for five neonicotinoid insecticides in environmental samples ranged from 1.8 to 16.5%, and good recoveries from 83.5 to 117.0% were obtained, indicating that magnetic zeolitic imidazolate framework 67/graphene oxide composites were feasible for analysis of trace analytes in environmental water samples.     

Phosphorus and Halogen Co‐Doped Graphene Materials and their Electrochemistry

Doping of graphene materials with heteroatoms is important as it can change their electronic and electrochemical properties. Here, graphene is co‐doped with n‐type dopants such as phosphorus and halogen (Cl, Br, I). Phosphorus and halogen are introduced through the treatment of graphene oxide with PX₃ gas (PCl₃, PBr₃, and PI₃). Graphene oxides are prepared through chlorate and permanganate routes. Detailed chemical and structural characterization demonstrates that the graphene sheets are covered homogeneously by phosphorus and halogen atoms. It is found that the amount of phosphorus and halogen introduced depends on the graphene oxide preparation method. The electrocatalytic effect of the resulting co‐doped materials is demonstrated for industrially relevant electrochemical reactions such as the hydrogen evolution and oxygen reduction reactions.     

Inherent Electrochemistry and Activation of Chemically Modified Graphenes for Electrochemical Applications

Graphene research is currently at the frontier of electrochemistry. Many different graphene‐based materials are employed by electrochemists as electrodes in sensing and in energy‐storage devices. Because the methods for their preparation are inherently different, graphene materials are expected to exhibit different electrochemical behaviors depending on the functionalities and density of defects present. Electrochemical treatment of these “chemically modified graphenes” (CMGs) represents an easy approach to alter surface functionalities and consequently tune the electrochemical performance. Herein, we report a preliminary electrochemical characterization of four common chemically modified graphenes, namely: graphene oxide, graphite oxide, chemically reduced graphene oxide, and thermally reduced graphene oxide. These CMGs were compared with graphite as a reference material. Cyclic voltammetry was used to ascertain the chemical functionalities present and to understand the potential ranges in which the materials were electroactive. Electrochemical treatment with either an oxidative or a reductive fixed potential were then carried out to activate these chemically modified graphenes. The effects of such electrochemical treatments on their electrocatalytic properties were then investigated by cyclic voltammetry in the presence of well‐known redox probes, such as [Fe(CN)₆]^4?/3?, Fe^3+/2+, [Ru(NH₃)₆]^2+/3+, and ascorbic acid. Thermally reduced graphene oxide exhibited the best electrochemical behavior amongst all of the CMGs, with the fastest rate of heterogeneous electron transfer (HET) and the lowest overpotentials. These findings will have far‐reaching consequences for the evaluation of different CMGs as electrode materials in electrochemical devices.     

Graphene‐Based Composite with γ‐Fe2O3 Nanoparticle for the High‐Performance Removal of Endocrine‐Disrupting Compounds from Water

Graphene is a 2D sp²‐hybridized carbon sheet and an ideal material for the adsorption‐based separation of organic pollutants. However, such potential applications of graphene are largely limited, owing to their poor solubility and extensive aggregation properties through graphene? graphene interactions. Herein, we report the synthesis of graphene‐based composites with γ‐Fe₂O₃ nanoparticle for the high‐performance removal of endocrine‐disrupting compounds (EDC) from water. The γ‐Fe₂O₃ nanoparticles partially inhibit these graphene? graphene interactions and offer water dispersibility of the composite without compromising much of the high surface area of graphene. In their dispersed form, the graphene component offers the efficient adsorption of EDC, whilst the magnetic iron‐oxide component offers easier magnetic separation of adsorbed EDC.     

Metal Oxide‐Coated Three‐Dimensional Graphene Prepared by the Use of Metal–Organic Frameworks as Precursors

A simple method for the preparation of metal‐oxide‐coated three‐dimensional (3D) graphene composites was developed. The metal–organic frameworks (MOFs) that served as the precursors of the metal oxides were first synthesized on the 3D graphene networks (3DGNs). The desired metal oxide/3DGN composites were then obtained by a two‐step annealing process. As a proof‐of‐concept application, the obtained ZnO/3DGN and Fe₂O₃/3DGN materials were used in a photocatalytic reaction and a lithium‐ion battery, respectively. We believe this method could be extended to the synthesis of other metal oxide/3DGN composites with 3D structures simply through the appropriate choice of specific MOFs as precursors.     

Enhanced Electrocatalytic Activity of Dual Template Based Pt/Cu‐zeolite A/Graphene for Methanol Electrooxidation

A novel Pt/Cu‐zeolite A/graphene based electrocatalyst was successfully prepared by chemical reduction method for methanol electrooxidation. Graphite oxide and Cu functionalized zeolite A were simultaneously reduced by NaBH₄ to prepare Cu‐zeolite A/graphene support which was used to deposit Pt nanoparticles. The nanostructure and composition of as‐prepared Pt/Cu‐zeolite A/graphene composites were characterized by X‐ray diffractometer, X‐ray fluorescence, Fourier transform infrared spectrometer and scanning electron microscopy. The electrocatalytic properties of Pt/Cu‐zeolite A/graphene modified electrode for methanol oxidation were investigated by cyclic voltammetry and chronoamperometry in 0.10 mol/L H₂SO₄ + 0.50 mol/L CH₃OH solution. Compared with Pt/zeolite A/graphene electrode and Pt/graphene electrode, Pt/Cu‐zeolite A/graphene based electrode exhibited obviously enhanced current and higher electrocatalytic activity for methanol electrooxidation. The increased electrocatalytic activity was attributed to the presence of zeolite A and reduced graphene oxide based dual template, which significantly increased the effective electrode surface and facilitated the diffusion of analytes into the electroactive catalyst.     

Pd embedded N,S co‐doped graphene wrapped core‐shell magnetic nanospheres: Engineered stable nanocatalyst for Suzuki couplings

Designed nitrogen and sulfur co‐doped graphene wrapped magnetic core‐shell supported Pd nanoparticles were synthesized through the following steps. Firstly, Fe₃O₄ was prepared, coated with silica and then functionalized with amine groups to create a positive charge on the structure for enhancing the interaction of the Fe₃O₄@SiO₂ with graphene oxide. Secondary, the pre‐catalyst wrapped with graphene to enhance adsorption of aromatic substrates through π–π stacking. Thirdly, graphene was doped with nitrogen and sulfur to increase the grafting of Pd in hybrid. Finally, Pd NPs were attached on the surface of pre‐engineered structure to produce Fe₃O₄@SiO₂@N,S‐wG@Pd which exhibited high performance in Suzuki reactions. This superior activity can be indexed to the incorporation of N and S atoms into graphene led to high anchoring and well‐dispersion of Pd NPs on the nanocomposite surface offering large amounts of active centers, that strongly increased the interaction between Pd and substrates to decreases Pd leaching.     

The influence of mesoporous SiO2‐graphene hybrid improved the flame retardancy of epoxy resins

A novel mesoporous SiO₂‐graphene nanohybrid was successfully synthesized by a 1‐pot hydrothermal synthesis method using tetraethylortho silicate and graphene oxide as initial materials to improve the dispersion of graphene in epoxy matrix. Subsequently, the SiO₂‐graphene nanohybrids were added into epoxy resin to investigate their fire behaviors. It was found that the incorporation of the as‐prepared SiO₂‐graphene nanohybrids into epoxy resin obviously increased the flame retardancy, compared with those of neat epoxy. This attractive feature of SiO₂‐graphene epoxy nanocomposites was attributed to the barrier effect as well as the labyrinth effect contributed by SiO₂‐graphene in EP resin.     

Synthesis and characterization of graphene oxide‐based hybrid ligand and its metal complexes: Highly efficient sensor and catalytic properties

A new graphene oxide‐based hybrid material (HL) and its Co(II), Cu(II) and Ni(II) metal complexes were prepared. Firstly, graphene oxide and (3‐aminopropyl)trimethoxysilane were reacted to give graphene oxide–3‐(aminopropyl)trimethoxysilane (GO‐APTMS) hybrid material. After that, hybrid material HL was synthesized from the reaction of GO‐APTMS and 2,6‐diformyl‐4‐methylphenol. Finally, Co(II), Cu(II) and Ni(II) complexes of HL were obtained. All the materials were characterized using various techniques. The chemosensor properties of HL were investigated against Na⁺, K⁺, Cd²⁺, Co²⁺, Cu²⁺, Hg²⁺, Ni²⁺, Zn²⁺, Al³⁺, Cr³⁺, Fe³⁺ and Mn³⁺ ions and it was found that HL has selective chemosensing to Fe³⁺ ion. All the graphene oxide‐supported complexes were used as heterogeneous catalysts in the oxidation of 2‐methylnaphthalene (2MN) to 2‐methyl‐1,4‐naphthoquinone (vitamin K₃, menadione) in the presence of hydrogen peroxide, acetic acid and sulfuric acid. The Cu(II) complex showed good catalytic properties compared to the literature. The selectivity of 2MN to vitamin K₃ was 60.23% with 99.75% conversion using the Cu(II) complex.     

Electrochemiluminescence Aptasensor for the MUC1 Protein Based on Multi‐functionalized Graphene Oxide Nanocomposite

The electrochemiluminescence (ECL) aptasensor was prepared for the detection of Mucin 1 based on its specific recognition by aptamer immobilized on multi‐functionalized graphene oxide nanocomposite, which was prepared with N‐(4‐aminobutyl)‐N‐ethylisoluminol (ABEI) and aptamer chemically bound to the surface of magnetic GO (nanoFe₃O₄@GO). ABEI and aptamer acted as the electrochemiluminophore and the capture device for Mucin 1 respectively. NanoFe₃O₄@GO brought multi‐functionalized graphene oxide nanocomposite attracted on the surface of magnetic glass carbon electrode through magnetism, enabled all the ABEI immobilized electrochemically active due to its good conductivity and thus then facilitated the sensitive detection of Mucin 1. In addition, the ECL aptasensor can be prepared through a one‐step process. Under optimal conditions, the ECL intensity of the aptasensor decreased proportionally to the logarithmic concentrations of Mucin 1 in the range of 0.005–1000 ng mL^?1. This aptasensor displays good specificity, stability, reproducibility and application. This method has a large potential because such a multi‐functionalized graphene oxide nanocomposite also may be applied to other ECL‐based aptasensors.     

Modular Covalent Graphene Functionalization with C60 and the Endohedral Fullerene Sc3N@C80: A Facile Entry to Synthetic‐Carbon‐Allotrope Hybrids

Two novel graphene‐fullerene hybrid structures, containing C₆₀ and endohedral Sc₃N@C₈₀ bound to graphene, instead of the formerly used graphene oxide, were efficiently synthesized via a reductive activation/exfoliation approach starting from pristine graphite. The structures of these multifunctional hybrid systems were unambiguously characterized by statistical Raman spectroscopy, TG‐MS, TG‐GC‐MS, and LD‐TOF mass spectroscopy, confirming the covalent bonding of the respective C₆₀/Sc₃N@C₈₀ moieties to the pristine graphene. Furthermore, assisted by temperature‐dependent Raman spectroscopy studies the corresponding defunctionalization processes were also investigated. Finally, the formation of a carbon allotrope hybrid material on the basis of C₆₀/Sc₃N@C₈₀ moieties coupled to graphene could be visualized by HRTEM.     

Aptamer functionalized magnetic graphene oxide nanocomposites for highly selective capture of histones

The binding coverage of aptamer was an important restricted factor for aptamer‐based affinity enrichment strategy for capturing target molecules. Herein, we designed and prepared aptamer functionalized graphene oxide based nanocomposites (GO/NH₂‐NTA/Fe₃O₄/PEI/Au), and the coverage density of aptamer was high to 33.1 nmol/mg. The high aptamer coverage density was contributed to the large surface area of graphene oxide. The successive modification of Nα,Nα‐Bis(carboxymethyl)‐L‐lysine, magnetic nanoparticles, polyethylenimine, and Au nanoparticles ensured the histone purification with fast speed and high purity. Histones could be captured rapidly and specifically from nucleoproteins by our aptamer based purification strategy, while traditional acid‐extraction could not specifically enrich histones. Compared with traditional acid‐extraction method, rapid and efficient discovery of histones and their post‐translational modifications, such as several kinds of methylation at H3.1K9 and H3.1K27, were achieved confidently. It demonstrated that our aptamer functionalized magnetic graphene oxide nanocomposites have a great potential for histone analysis.     

Fe3O4/reduced graphene oxide‐carbon nanotubes composite for the magnetic solid‐phase extraction and HPLC determination of sulfonamides in milk

A novel magnetic adsorbent Fe₃O₄/reduced graphene oxide‐carbon nanotubes, was prepared by one‐pot solvothermal synthesis method. It was characterized by scanning electron microscopy, X‐ray powder diffraction and vibrating sample magnetometry. The diameter of Fe₃O₄ microparticles was about 350 nm, which were covered by carbon nanotubes and reduced graphene oxide sheets, while carbon nanotubes inserted between the reduced graphene oxide sheets effectively prevented their aggregation. The composite had large surface area and good magnetic property, suiting for magnetic solid‐phase extraction and the determination of sulfonamides, by coupling with high‐performance liquid chromatography. Under the optimized conditions (including extraction time, amount of adsorbent, solution pH, ionic strength and desorption conditions), a good linear was achieved in the concentration range of 5–500 μg/L and the low limits of detection and low limits of quantification were 0.35–1.32 and 1.16–4.40 μg/L, respectively. The enrichment factors were estimated to be 24.72 to 30.15 fold. The proposed method was applied for the detection of sulfonamides in milk sample and the recoveries were 88.4–105.9%, with relative standard deviations of 0.74–5.38%.     

Graphene oxide coated capillary for the analysis of endocrine‐disrupting chemicals by open‐tubular capillary electrochromatography with amperometric detection

A graphene oxide‐coated capillary was fabricated by using 3‐aminopropyltriethoxysilane as the cross‐linking agent. It was used for the separation and detection of three endocrine‐disrupting chemicals, including bisphenol A, 4‐nonylphenol, and 4‐octylphenol by capillary electrochromatography. Due to the hydrophobicity, hydrogen bonding, and π–π interaction between graphene oxide and the analytes, the three analytes could be well separated in pH = 11.0, 20 mmol/L Na₂B₄O₇‐NaOH/methanol mobile phase (50:50, v/v) within 950 s. After preconcentration, the detection limits were 6.7 × 10^?10, 3.3 × 10^?9, and 6.7 × 10^?10 mol/L (S/N = 3) for bisphenol A, nonylphenol, and octylphenol, respectively. The developed method was successfully applied to the determination of the above analytes in water samples. The satisfactory result demonstrated that the graphene oxide coated capillary used in capillary electrochromatography with amperometric detection was convenient to prepare, highly stable, and had good reproducibility.     

π‐Conjugated Carbon Radicals at Graphene Oxide to Initiate Ultrastrong Chemiluminescence

Graphene oxide has widely been employed in various fields, but its structure and composition has still not been fully understood. Here we report that freshly prepared graphene oxide exhibits a large number of π‐conjugated carbon radicals at its π‐network plane, which result from the addition reaction of hydroxyl radicals from H₂O₂ onto the conjugated double bonds of graphene oxide. The π‐conjugated carbon radicals can directly initiate the long‐lasting visible chemiluminescence of luminol, which is even stronger than that obtained when horseradish peroxidase and H₂O₂ are used. Previously, graphene oxide was mainly reported to be a quencher of chemiluminescence instead. Remarkably, the reacted radicals can be regenerated, thereby enabling the repetitive initiation of chemiluminescence by re‐treatment of graphene oxide. The results reported here provide a new understanding of the structure, properties, and applications of graphene oxide.     

Self‐Assembling Synthesis of Free‐standing Nanoporous Graphene–Transition‐Metal Oxide Flexible Electrodes for High‐Performance Lithium‐Ion Batteries and Supercapacitors

The synthesis of nanoporous graphene by a convenient carbon nanofiber assisted self‐assembly approach is reported. Porous structures with large pore volumes, high surface areas, and well‐controlled pore sizes were achieved by employing spherical silica as hard templates with different diameters. Through a general wet‐immersion method, transition‐metal oxide (Fe₃O₄, Co₃O₄, NiO) nanocrystals can be easily loaded into nanoporous graphene papers to form three‐dimensional flexible nanoarchitectures. When directly applied as electrodes in lithium‐ion batteries and supercapacitors, the materials exhibited superior electrochemical performances, including an ultra‐high specific capacity, an extended long cycle life, and a high rate capability. In particular, nanoporous Fe₃O₄–graphene composites can deliver a reversible specific capacity of 1427.5 mAh g^?1 at a high current density of 1000 mA g^?1 as anode materials in lithium‐ion batteries. Furthermore, nanoporous Co₃O₄–graphene composites achieved a high supercapacitance of 424.2 F g^?1. This work demonstrated that the as‐developed freestanding nanoporous graphene papers could have significant potential for energy storage and conversion applications.     

Electrochemically Exfoliated Graphene and Graphene Oxide for Energy Storage and Electrochemistry Applications

Top‐down methods are of key importance for large‐scale graphene and graphene oxide preparation. Electrochemical exfoliation of graphite has lately gained much interest because of the simplicity of execution, the short process time, and the good quality of graphene that can be obtained. Here, we test three different electrolytes, that is, H₂SO₄, Na₂SO₄, and LiClO₄, with a common exfoliation procedure to evaluate the difference in structural and chemical properties that result for the graphene. The properties are analyzed by means of scanning transmission electron microscopy (STEM), Raman spectroscopy, and X‐ray photoelectron spectroscopy. We then tested the graphene materials for electrochemical applications, measuring the heterogeneous electron transfer (HET) rates with a Fe(CN)₆^3?/4? redox probe, and their capacitive behavior in alkaline solutions. We correlate the electrochemical features with the presence of structural defects and oxygen functionalities on the graphene materials. In particular, the use of LiClO₄ during the electrochemical exfoliation of graphite allowed the formation of highly oxidized graphene with a C/O ratio close to 4.0 and represents a possible avenue for the mass production of graphene oxide as valid alternative to the current laborious and dangerous chemical procedures, which also have limited scalability.     

Effect of the Reaction Alkaline Environment on the Morphology and Spectroscopic Characterizations of ZnO‐Graphene Composite

ZnO‐graphene composite was synthesized by using graphene oxide (GO), zinc acetate (Zn(CH₃COO)₂⋅2H₂O), sodium hydroxide (NaOH) and ethylene glycol as precursors through a one‐pot hydrothermal process. The concentration of NaOH solution had an important effect on the morphology, defects and spectroscopic characterizations of the ZnO‐graphene composite. With the increase of concentration of NaOH solution, the morphology of the composite changed significantly. The morphological evolution was analyzed through SEM and TEM observations, and the Raman and PL spectral variations were discussed.     

Selective separation and determination of the synthetic colorants in beverages by magnetic solid‐phase dispersion extraction based on a Fe3O4/reduced graphene oxide nanocomposite followed by high‐performance liquid chromatography with diode array detection

A facile adsorbent, a nanocomposite of Fe₃O₄ and reduced graphene oxide, was fabricated for the selective separation and enrichment of synthetic aromatic azo colorants by magnetic solid‐phase dispersion extraction. The nanocomposite was synthesized in a one‐step reduction reaction and characterized by atomic force microscopy, scanning electron microscopy, Fourier transform infrared spectroscopy, Raman spectroscopy, X‐ray diffraction and Brunauer–Emmett–Teller analysis. The colorants in beverages were quickly adsorbed onto the surface of the nanocomposite with strong π–π interactions between colorants and reduced graphene oxide, and separated with the assistance of an external magnetic field. Moreover, the four colorants in beverages were detected at different wavelengths by high performance liquid chromatography with diode array detection. A linear dependence of peak area was obtained over 0.05–10 μg/mL with the limits of detection of 10.02, 11.90, 10.41, 15.91 ng/mL for tartrazine, allure red, amaranth, and new coccine, respectively (signal to noise = 3). The recoveries for the spiked colorants were in the range of 88.95–95.89% with the relative standard deviation less than 2.66%. The results indicated that the nanocomposite of Fe₃O₄ and reduced graphene oxide could be used as an excellent selective adsorbent for aromatic compounds and has potential applications in sample pretreatment.     

Heterogenized peroxopolyoxotungstate catalyst on the surface of clicked magnetite‐graphene oxide nanocomposite: Magnetically recoverable epoxidation catalyst

A new heterogeneous catalyst for the epoxidation of olefins was prepared by immobilization of peroxophosphotungstate anions on the surface of clicked magnetite‐graphene oxide as magnetically recoverable support. To prepare the heterogeneous catalyst, the clicked magnetite‐graphene oxide support was prepared by thiolene click reaction of thiol functionalized graphene oxide with vinyl modified magnetite nanoparticles. The tailored support was then modified with aminopropyl groups followed by electrostatic interaction with peroxophosphotungstate anions to achieve the desired heterogeneous catalyst. Characterization of the catalyst was performed by various physicochemical methods which confirmed the successful immobilization of peroxopolyoxotungstate species on the surface of clicked magnetite‐graphene oxide. Catalytic activity of the catalyst revealed its high catalytic activity and selectivity in the epoxidation of various olefins in the presence of H₂O₂ as green oxidant. This heterogeneous catalyst can be magnetically reused several times without significant loss of activity and selectivity.