Polymerization of graphene oxide nanosheet by using of aminoclay: Electrocatalytic activity of its platinum nanohybrids

This study describes the polymerization of graphene oxide (GO) nanosheet to reduced‐GO‐aminoclay (RGC) by covalent functionalization of chemically reactive epoxy groups on the basal planes of GO with amine groups of magnesium phyllosilicate clay (known as aminoclay). The resulting RGC sheets were characterized and applied to support platinum nanostructures at toluene/water interface. Pt nanoparticles (NPs) with diameters about several nanometers were adhered to RGC sheets by chemical reduction of [PtCl₂(cod)] (cod = cis,cis‐1,5‐cyclooctadiene) complex. Catalytic activity of Pt NPs thin films were investigated in the methanol oxidation reaction. Cyclic voltammetry results exhibit that the Pt/reduced‐GO (RGO) and Pt/RGC thin films showed improved catalytic activity in methanol oxidation reaction in comparison to other Pt NPs thin films, demonstrating that the prepared Pt/RGO and Pt/RGC thin films are promising catalysts for direct methanol fuel cell.     

Photo Catalytic Degradation of Azo Dyes over Mn2+ Doped TiO2 Catalyst under UV/Solar Light:An Insight to the Route of Electron Transfer in the Mixed Phase of Anatase and Rutile

Mn²⁺ ion was doped into the TiO₂ matrix and its photocatalytic activity was evaluated for the degradation of a mono azo dye methyl orange (MO) and a di‐azo dye brilliant yellow (BY) under UV/solar light. X‐ray diffraction results revealed the phase transformation from anatase to rutile due to the inclusion of Mn²⁺ ion into the TiO₂ matrix. All the doped catalysts showed a red shift in the band gap to the visible region. The degradation reaction of the dyes was found to be dependent on its structure. It was found that mono azo dye degrades faster than di azo dye under UV/solar light. The rate constant under identical conditions calculated for the degradation of MO is 2.4 times (under UV light) and 4.5 times (under solar light) higher compared to BY. Among the photocatalysts studied, Mn²⁺(0.06 at.%)‐TiO₂ showed higher activity under both UV and solar light illumination. The synergestic effect in the bicrystalline framework of anatase and rutile effectively suppresses the charge carrier recombination and enhances the photocatalytic activity. The degradation reaction was followed by UV‐visible spectroscopy and the photoproducts formed were analyzed by GC‐MS techniques.     

Photoelectrocatalytic activity of immobilized Yb doped WO_3 photocatalyst for degradation of methyl orange dye

Pure WO_3 and Yb:WO_3 thin films have been synthesized by spray pyrolysis technique. Effect of Yb doping concentration on photoelectrochemical, structural, morphological and optical properties of thin films are studied. X-ray diffraction analysis shows that all thin films are polycrystalline nature and exhibit monoclinic crystal structure. The 3 at% Yb:WO_3 film shows superior photoelectrochemical(PEC) performance than that of pure WO_3 film and it shows maximum photocurrent density(Iph= 1090 μA/cm~2) having onset potentials around +0.3 V/SCE in 0.01 M HClO_4. The photoelectrocatalytic process is more effective than that of the photocatalytic process for degradation of methyl orange(MO) dye. Yb doping in WO_3 photocatalyst is greatly effective to degrade MO dye. The enhancement in photoelectrocatalytic activity is mainly due to the suppressing the recombination rate of photogenerated electron-hole pairs. The mineralization of MO dye in aqueous solution is studied by measuring chemical oxygen demand(COD) values.     

Enhanced Photocatalytic Degradation of Synthetic Dyes and Industrial Dye Wastewater by Hydrothermally Synthesized G–CuO–Co<Subscript>3</Subscript>O<Subscript>4</Subscript> Hybrid Nanocomposites Under Visible Light Irradiation

To enhance the degradation of colour and chemical oxygen demand using photocatalytic activity, Graphene–CuO–Co₃O₄ hybrid nanocomposites were synthesized using an in situ surfactant free facile hydrothermal method. The photocatalytic degradation of synthetic anionic dyes, methyl orange (MO) and Congo red (CR), and industrial textile wastewater dyes under visible light irradiation was evaluated. The synthesized nanocomposite was characterized structurally and morphologically using X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy, Raman spectroscopy, high-resolution transmission electron microscope, and Fourier transform infrared spectroscopy. Evaluation of the colour indicated complete removal at 15 min of irradiation for the MO and CR dyes, with 99% degradation efficiency. The reaction time for the primary effluent wastewater dye was 60 min for 81% dye removal. In contrast, a longer reaction time was required to meet the national discharge regulation for the raw wastewater dye, 300 min for 60% dye removal. The mechanism for dye degradation using the Graphene–CuO–Co₃O₄ hybrid nanocomposite was elucidated using the Langmuir–Hinshelwood model, and the rate constant and half-life of the degradation process were calculated. The results demonstrate that photocatalytic degradation using a hybrid nanocomposite and visible light irradiation is a sustainable alternative technology for removing colour from wastewater dye.     

Straightforward Synthesis of Mn3O4/ZnO/Eu2O3-Based Ternary Heterostructure Nano-Photocatalyst and Its Application for the Photodegradation of Methyl Orange and Methylene Blue Dyes

Zinc oxide-ternary heterostructure Mn₃O₄/ZnO/Eu₂O₃ nanocomposites were successfully prepared via waste curd as fuel by a facile one-pot combustion procedure. The fabricated heterostructures were characterized utilizing XRD, UV–Visible, FT-IR, FE-SEM, HRTEM and EDX analysis. The photocatalytic degradation efficacy of the synthesized ternary nanocomposite was evaluated utilizing model organic pollutants of methylene blue (MB) and methyl orange (MO) in water as examples of cationic dyes and anionic dyes, respectively, under natural solar irradiation. The effect of various experimental factors, viz. the effect of a light source, catalyst dosage, irradiation time, pH of dye solution and dye concentration on the photodegradation activity, was systematically studied. The ternary Mn₃O₄/ZnO/Eu₂O₃ photocatalyst exhibited excellent MB and MO degradation activity of 98% and 96%, respectively, at 150 min under natural sunlight irradiation. Experiments further conclude that the fabricated nanocomposite exhibits pH-dependent photocatalytic efficacy, and for best results, concentrations of dye and catalysts have to be maintained in a specific range. The prepared photocatalysts are exemplary and could be employed for wastewater handling and several ecological applications.     

低温静电自组装法制备贵金属修饰TiO_2纳米结构薄膜及其增强的光催化性能(英文)

以碱-水热法在金属Ti片上原位生长了TiO2纳米结构(纳米花和纳米线)薄膜,并采用低温静电自组装方法将超细贵金属(金、铂、钯)纳米颗粒均匀沉积于多孔TiO2薄膜上.负载于Ti片上的贵金属/TiO2纳米结构薄膜具有一体化结构、多孔架构和高光催化活性.超高分辨率场发射扫描电子显微镜(FESEM)直接观察表明贵金属纳米颗粒在TiO2表面分布均匀,且颗粒之间相互分离,金、铂、钯纳米颗粒的平均粒径分别约为4.0、2.0和10.0nm.俄歇电子能谱(AES)纵深成分分析表明贵金属不仅沉积于薄膜表面,且大量分布于TiO2纳米结构薄膜内部,其深度超过580 nm.X射线光电子能谱(XPS)分析表明,经300°C下在空气中热处理后,纳米金仍保持金属态,纳米铂部分被氧化成PtOabs,而钯粒子则完全被氧化成氧化钯(PdO).以低温静电自组装法沉积贵金属,贵金属负载量可通过调节组装时间与溶胶pH值来控制.光催化降解甲基橙的结果表明,沉积的纳米金和铂能显著增加TiO2纳米结构薄膜的光催化活性,说明金和铂粒子可促进光生载流子的分离;但负载的PdO对TiO2薄膜的光催化性能增强几乎无作用.     

A Novel Kinetic Approach for Photocatalytic Degradation of Azo Dye with CdS and Ag/CdS Nanoparticles Fixed on a Cement Bed in a Continuous‐Flow Photoreactor

Azo dyes are one of the synthetic dyes that have been used in many textile industries. Azo dye and their intermediate products are toxic, carcinogenic, and mutagenic to aquatic life. Removal of azo dyes is one of the main challenges before releasing the wastes discharged by textile industries. Photocatalytic degradation of azo dyes by nanoparticles is one of the environment‐friendly methods used for the removal of dyes from textile effluents. Therefore, this study focused on degradation of azo dye, Direct Red 264. Photocatalytic degradation of DR 264 azo dye was investigated using CdS and Ag/CdS nanoparticles immobilized on a cement bed in a continuous‐flow photoreactor under UV‐C exposure. The effect of the parameters of type and mass of catalyst, temperature, flow rate, dye concentration, and light intensity were evaluated for azo dye removal. Under optimal conditions, photocatalytic degradation of DR 264 azo dye using Ag/CdS nanoparticles immobilized on a cement bed in a continuous‐flow photoreactor obtained an efficiency of 99.99%. A developed kinetic model was proposed based on the intrinsic elementary reactions. The proposed model is in a good agreement with the Langmuir–Hinshelwood (L–H) equation. The pseudo–steady‐state approximation has considered for the concentration of hydroxyl radicals associated with the L–H model under certain conditions and explains consistently the dependence of the apparent kinetic parameter, k_obs (the reaction rate constant), and K_R (the adsorption equilibrium constant) with the light intensity. Based on the model, k_obs for Ag/CdS was greater than the CdS nanoparticles.     

Induction and inversion of chirality in poly‐L‐lysine and methyl orange complex

The mechanism of complexation of poly‐L‐lysine (PLL) with methyl orange (MO) and the appearance of induced circular dichroism (ICD) were investigated as a function of dye concentration and temperature and compared with that of the PLL‐ethyl orange complex. The formation of stoichiometric complexes with uniform size and intensities of ICDs depended on the length of alkyl groups (methyl and ethyl) as determined from quartz crystal microbalance measurement, absorption spectra, and CD spectra data. Furthermore, at constant PLL concentration, a dependence of the inversion of the ICD on the MO concentration (CMO) was observed in the PLL‐MO complexes, which to our knowledge has not been reported for a constant dye concentration system. The positive ICD in the PLL‐MO complexes observed at CMO lower than 2.0 × 10^?5 M showed reversible changes in response to heating and cooling, whereas the negative ICD in PLL‐MO complexes observed at higher CMO inverted to positive ICD values in response to a decrease in temperature. These results demonstrate the alkyl group substituent in the dye, dye concentration, and temperature play important roles in the formation of PLL‐azo dye complex and ICD appearance. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Studies on photocatalytic activity of Ag/TiO2 films

Ag/TiO₂ photocatalytic films were produced by hybrid sol-gel method. The photocatalytic degradation of methyl orange (MO) in aqueous solution under 365 nm irradiation on TiO₂ and Ag/TiO₂ thin films was investigated. The state and amount of Ag species within the film and the enhancement mechanism of photocatalytic activity of Ag/TiO₂ were discussed. With a loading molar ratio of Ag/Ti = 0.135 in TiO₂ film, the maximum catalytic efficiency was observed. __________ Translated from Journal of Beijing Normal University (Natural Sciences), 2005, 41(6) (in Chinese)     

Relating the Composition of PtxRu100−x/C Nanoparticles to Their Structural Aspects and Electrocatalytic Activities in the Methanol Oxidation Reaction

A controlled composition‐based method—that is, the microwave‐assisted ethylene glycol (MEG) method—was successfully developed to prepare bimetallic Pt_xRu_100?x/C nanoparticles (NPs) with different alloy compositions. This study highlights the impact of the variation in alloy composition of Pt_xRu_100?x/C NPs on their alloying extent (structure) and subsequently their catalytic activity towards the methanol oxidation reaction (MOR). The alloying extent of these Pt_xRu_100?x/C NPs has a strong influence on their Pt d‐band vacancy and Pt electroactive surface area (Pt ECSA); this relationship was systematically evaluated by using X‐ray absorption (XAS), scanning electron microscopy (SEM) coupled with energy dispersive X‐ray spectroscopy (EDX), transmission electron microscopy (TEM), density functional theory (DFT) calculations, and electrochemical analyses. The MOR activity depends on two effects that act in cooperation, namely, the number of active Pt sites and their activity. Here the number of active Pt sites is associated with the Pt ECSA value, whereas the Pt‐site activity is associated with the alloying extent and Pt d‐band vacancy (electronic) effects. Among the Pt_xRu_100?x/C NPs with various Pt:Ru atomic ratios (x=25, 50, and 75), the Pt₇₅Ru₂₅/C NPs were shown to be superior in MOR activity on account of their favorable alloying extent, Pt d‐band vacancy, and Pt ECSA. This short study brings new insight into probing the synergistic effect on the surface reactivity of the Pt_xRu_100?x/C NPs, and possibly other bimetallic Pt‐based alloy NPs.     

Modification of photocatalytic TiO2 thin films by electron beam irradiation

Noble metal-modified TiO₂ films were prepared by electron beam deposition of Pt, Pd, Au and Ag on the surface of TiO₂ films with diameters ranging from <1 nm to 500 nm. The morphology of the films was characterized by X-ray diffractometry (XRD), field emission scanning electron microscope (FMSEM) and transmission electron microscope (TEM). The photocatalytic capability of the films were tested and compared by degradation of methyl orange (MO) in aqueous solutions under both UV and visible light illumination.     

Adsorption of acid red 114 and reactive black 5 in aqueous solutions on dendrimer‐conjugated magnetic nanoparticles

The adsorption of the dyes Acid Red 114 and Reactive Black 5 in aqueous solutions on polyhydroxyl dendrimer magnetic nanoparticles (Fe₃O₄@SiO₂‐TRIS) was studied in a batch system. The Fe₃O₄@SiO₂‐TRIS NPs were characterized by Fourier transform infrared spectroscopy, X‐ray diffraction, and transmission electron microscopy. Experiments were performed under different conditions such as the initial dye concentration, adsorbent dose, and pH. The pseudo‐second‐order model provided a very good fit for the two anionic dyes. The Langmuir and Freundlich adsorption models were used to describe the equilibrium isotherms at different temperatures, and the former agreed very well with the experimental data. However, the adsorption capacity of Fe₃O₄@SiO₂‐TRIS NPs was reduced during surface modification, which could be due to the dye occupying the binding sites of the dendrimer. Thermodynamic parameters, namely the change in free energy (ΔG⁰), enthalpy (ΔH⁰), and entropy (ΔS⁰), were also determined.     

Methanol oxidation on the PtPd(111) alloy surface: A density functional theory study

The mechanisms of methanol (CH₃OH) oxidation on the PtPd(111) alloy surface were systematically investigated by using density functional theory calculations. The energies of all the involved species were analyzed. The results indicated that with the removal of H atoms from adsorbates on PtPd(111) surface, the adsorption energies of (i) CH₃OH, CH₂OH, CHOH, and COH increased linearly, while those of (ii) CH₃OH, CH₃O, CH₂O, CHO, and CO exhibited odd‐even oscillation. On PtPd(111) surface, CH₃OH underwent the preferred initial C H bond scission followed by successive dehydrogenation and then CHO oxidation, that is, CH₃OH → CH₂OH → CHOH → CHO → CHOOH → COOH → CO₂. Importantly, the rate‐determining step of CH₃OH oxidation was found to switch from CO → CO₂ on Pt(111) to COOH → CO₂ + H on PtPd(111) with a lower energy barrier of 0.96 eV. Moreover, water also decomposed into OH more easily on PtPd(111) than on Pt(111). The calculated results indicate that alloying Pt with Pd could efficiently improve its catalytic performance for CH₃OH oxidation through altering the primary pathways from the CO path on pure Pt to the non‐CO path on PtPd(111).     

Uniformly Dispersed and Controllable Ligand‐Free Silver‐Nanoparticle‐Decorated TiO2 Nanotube Arrays with Enhanced Photoelectrochemical Behaviors

Homogeneously dispersed silver nanoparticles (AgNPs) were successfully decorated onto the surface of TiO₂ nanotube arrays (TNTA) by means of an in situ photoreduction method. TNTA films as supports exhibit excellent properties to prevent agglomeration of AgNPs, and they also avoid using polymer ligands, which is deleterious to enhancing the properties of the fabricated NPs. The silver particle size and its content could be controlled just by changing the immersion time. Detailed SEM and TEM analyses combined with energy‐dispersive X‐ray spectroscopy analyses with different immersion times (5, 10, 30, 60 min) have revealed the variation tendency. The prepared Ag/TNTA composite films were also characterized by XRD, X‐ray photoelectron spectroscopy, and high‐resolution TEM. The UV/Vis diffuse reflectance spectra displayed a redshift of the absorption peak with the growth of AgNPs. The photocurrent response and the photoelectrocatalytic degradation of methyl orange (MO) were used to evaluate the photoelectrochemical properties of the fabricated samples. The results showed that the photocurrent response and photoelectrocatalytic activity largely depended on the loaded Ag particle size and content. TNTA films with a diameter of 17.92 nm and silver content of 1.15 at % showed the highest photocurrent response and degradation rate of MO. The enhanced properties could be attributed to the synergistic effect between AgNPs and TiO₂. To make good use of this effect, particle size and silver content should be well controlled to develop the electron charge and discharge process during the photoelectrical process. Neither smaller nor larger AgNPs caused decreased photoelectrical properties.     

Ligandless C‐C bond formation via Suzuki–Miyaura reaction in micelles or water–ethanol solution using PdPtZn and PdZn nanoparticle thin films

PdPtZn and PdZn nanoparticle (NP) thin films were synthesized by the reduction of [PdCl₂(cod)], [PtCl₂(cod)] (cod = cis,cis‐1,5‐cyclooctadiene) and [Zn(acac)₂] (acac = acetylacetonate) complexes at an oil–water interface. The structure and morphology of the as‐prepared NPs were characterized with X‐ray diffraction, transmission electron microscopy and energy dispersive analysis of X‐rays. Catalytic activity of the prepared NPs was investigated in the Suzuki–Miyaura cross‐coupling reaction in H₂O–EtOH and various micellar media systems such as cetyltrimethylammonium bromide (cationic surfactant), sodium dodecylsulfate (anionic surfactant) and Pluronic P123 (non‐ionic surfactant). PdPtZn and PdZn thin films exhibited higher catalytic activity compared to Pd thin film in the Suzuki–Miyaura coupling reaction due to the appropriate interaction between palladium, platinum and zinc metals. Copyright © 2015 John Wiley & Sons, Ltd.     

Enhancing photocatalytic activity of titanium dioxide through incorporation of MIL‐53(Fe) toward degradation of organic dye

Photocatalytic activity of titanium(IV) oxide (TiO₂) can be enhanced through modification of its surface‐active sites. Here, iron(III) carboxylate [MIL‐53[Fe]]‐incorporated TiO₂ (as MIL‐53(Fe)/TiO₂) was prepared using a hydrothermal method. This material was then calcined at 500°C to obtain a MIL‐53(Fe)‐derived γ‐Fe₂O₃/TiO₂ photocatalyst. A photocatalytic study of MIL‐53(Fe)/TiO₂ and MIL‐53(Fe)‐derived γ‐Fe₂O₃/TiO₂ toward cationic methylene blue (MB) and anionic methyl orange (MO) showed that MIL‐53(Fe)/TiO₂ (0.25 wt%) and MIL‐53(Fe)‐derived γ‐Fe₂O₃/TiO₂ (0.75 wt%) resulted the best degree of dye degradation. The MIL‐53(Fe)‐derived γ‐Fe₂O₃/TiO₂ (0.75 wt%) composite for instance is capable of degrading almost 100% of 20‐ppm MB and MO, respectively, within 6 hr. Photocatalytic degradation of MB and MO was well fitted to the Langmuir‐Hinshelwood pseudo‐first order kinetics model, which indicates physisorption as the key partway that facilitates dye decomposition on the surface of a photocatalyst under UV‐A irradiation. This study provides new insights into the exploration of MILs/TiO₂ materials for the environmental remediation and pollution control.     

Formation and study of thin films oftert-butyl-substituted thiopyrylium dyes

The formation of thin films of symmetrical and asymmetrical thiopyrylium dyes, containingtert-butyl substituents, on glass supports was studied. The films were deposited by centrifugation of solutions of individual dyes or dye—polymer [poly(methyl methacrylate)] compositions. The dye: polymer ratios necessary for the formation of WORM recording layers based on these dyes were determined. The use of a polymeric matrix increases the film thickness and optical density but decreases its reflection power and does not allow crystallization of the dye on the support to be completely avoided. An increase in the number oftert-butyl groups in the dye molecule prevents crystallization of the recording layer in the case of symmetrical dye molecules, but does not prevent it for asymmetrical molecules. The data obtained were interpreted in terms of geometrical views on the interaction of dye molecules in thin layers. Translated fromIzestiya Akademii Nauk. Seriya Khimicheskaya, No. 7, pp. 1343–1349, July, 1998.     

Polymeric Carbon Nitride/Mesoporous Silica Composites as Catalyst Support for Au and Pt Nanoparticles

Small and homogeneously dispersed Au and Pt nanoparticles (NPs) were prepared on polymeric carbon nitride (CN_x)/mesoporous silica (SBA‐15) composites, which were synthesized by thermal polycondensation of dicyandiamide‐impregnated preformed SBA‐15. By changing the condensation temperature, the degree of condensation and the loading of CN_x can be controlled to give adjustable particle sizes of the Pt and Au NPs subsequently formed on the composites. In contrast to the pure SBA‐15 support, coating of SBA‐15 with polymeric CN_x resulted in much smaller and better‐dispersed metal NPs. Furthermore, under catalytic conditions the CN_x coating helps to stabilize the metal NPs. However, metal NPs on CN_x/SBA‐15 can show very different catalytic behaviors in, for example, the CO oxidation reaction. Whereas the Pt NPs already show full CO conversion at 160 °C, the catalytic activity of Au NPs seems to be inhibited by the CN_x support.     

Efficiency enhancement of solid‐state dye sensitized solar cell by in situ deposition of CuI

Solid‐state dye‐sensitized solar cells based on nanocrystalline TiO₂ thin film with the structures TiO₂/dye/CuI/Pt and TiO₂/dye/In situ CuI/CuI/Pt were developed in order to compare the use of In situ deposited CuI (In situ CuI). Porosity of the screen‐printed nanoporous TiO₂ thin film was enhanced by the addition of polystyrene balls. Evidence of decrease in interfacial resistance was observed by electrochemical impedance measurement for the device with In situ deposited CuI as compared to that without In situ deposited CuI as hole conductor. This was attributed to good interfacial contacts and better charge transfer between CuI and dye‐sensitized TiO₂ nanoparticles, which resulted in the enhancement of power conversion efficiency from 0.058 to 1.01%. Copyright © 2008 John Wiley & Sons, Ltd.     

Photoinduced Electron Transfer in Perylene‐TiO2 Nanoassemblies

The photosensitization effect of three perylene dye derivatives on titanium dioxide nanoparticles (TiO₂ NPs) has been investigated. The dyes used, 1,7‐dibromoperylene‐3,4,9,10‐tetracarboxy dianhydride (1), 1,7‐dipyrrolidinylperylene‐3,4,9,10‐tetracarboxy dianhydride (2) and 1,7‐bis(4‐tert‐butylphenyloxy)perylene‐3,4,9,10‐tetracarboxy dianhydride (3) have in common bisanhydride groups that convert into TiO₂ binding groups upon hydrolysis. The different substituents on the bay position of the dyes enable tuning of their redox properties to yield significantly different driving forces for photoinduced electron transfer (P_eT). Recently developed TiO₂ NPs having a small average size and a narrow distribution (4 ± 1 nm) are used in this work to prepare the dye‐TiO₂ systems under study. Whereas successful sensitization was obtained with 1 and 2 as evidenced by steady‐state spectral shifts and transient absorption results, no evidence for the attachment of 3 to TiO₂ was observed. The comparison of the rates of P_eT (k_PeT) for 1‐ and 2‐TiO₂ systems studied in this work with those obtained for previously reported analogous systems, having TiO₂ NPs covered by a surfactant layer (Hernandez et al. [2012] J. Phys. Chem. B., 117, 4568–4581), indicates that k_PeT for the former systems is slower than that for the later. These results are interpreted in terms of the different energy values of the conduction band edge in each system.