Effect of gamma radiation on fluoropolymers

A series of fluoropolymer films were synthesized by reacting several bisphenol monomers with 1,3‐bis(1,1,1,3,3,3‐hexafluoro‐2‐pentafluorophenyl methoxy‐2‐propyl)benzene via a nucleophilic aromatic substitution to form polyethers. The bisphenols used included two diphenol‐substituted spirodilactams (SDL; aliphatic and aromatic), biphenol, bisphenol A, bisphenol AF, bisphenol O, and bisphenol F to form seven different polymers. Polymers were irradiated by a Gamma beam 651‐PT at a dose rate of 10.5 kGy/h; the absorbed dose in each film was varied between 300 and 1000 kGy. The effect on the chemical structure upon radiation was studied by DSC, TGA, FTIR‐ATR, and NMR after and before irradiation. Thermal analysis showed a lessened thermal stability and a lower T_g after irradiation. Further, irradiation caused a decrease in molecular weight as a result of cleavage of sp³ bonds. These data allowed calculation of the radiochemical yield scission (G_s) for each of these polymers. The SDL aromatic system proved the most radiation‐resistant. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1617–1626, 2009     

Pyridinium chlorochromate oxidation route to polyaniline

In this work, for the first time, pyridinium chlorochromate is used as an oxidizing agent inorder to oxidize aniline to polyaniline salts via an aqueous polymerization pathway in the presence of protic acids such as sulfuric, nitric, hydrochloric and phosphoric acid. The polymer samples were characterized by infrared, electronic absorption spectral, elemental analysis, conductivity, density and water absorption measurements. The results of the polyaniline salts prepared by pyridinium chlorochromate as an oxidizing agent were compared with that of the polyaniline salt prepared by ammonium persulfate. Generally, aniline is oxidized using ammonium persulfate as an oxidizing agent, which is unstable. In this work, pyridinium chlorochromate is used to oxidize aniline to polyaniline salt and the polymerization reaction could be completed in 30 min. Copyright © 2003 John Wiley & Sons, Ltd.     

Stability of polyaniline in air and acidic water

Polyaniline is a member of the class of electrically conducting polymers, having possible commercial applications such as coatings. Aqueous‐based polyaniline coatings are preferred over organic solvent or concentrated strong acid based coatings because water is not a pollutant. The overall goal of this study was to further the development of water‐based polyaniline coatings by an examination of the effect of acidic water (pH 1.18) and air on polyaniline. Knowledge of the effect of water on the structure, molecular weight, electrical conductivity, and diffusion of the dopant assisted in ascertaining whether polyaniline degraded with water exposure. Knowledge of how Fourier transform infrared (FTIR) spectra would be affected by dry air was important for determining if polyaniline was chemically stable with time. The results showed that the molecular weight, ultraviolet–visible and FTIR spectra, and carbon‐to‐nitrogen molar ratio in the polymer backbone all remained unchanged during acidic water immersion. The constant nature of these physical parameters showed a high degree of water stability. A chloride ion diffusion coefficient of 2.8 to 85 × 10^?9 cm²/h, the chloride concentration, and the electrical conductivity were also measured with the water immersion time. Aging polyaniline powders in a desiccator for 5 years showed no effect on the molecular structure, as indicated by the FTIR spectrum. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 807–822, 2003     

Degradation mechanism of poly(ether‐urethane) Estane® induced by high‐energy radiation. II. Oxidation effects

To predict long‐term polymer behavior during a nuclear waste storage time, radiation effects on a segmented aromatic poly(ether‐urethane) induced by high‐energy radiation under oxygen atmosphere were investigated. To obtain a predictive model of polymer radio‐oxidation during several centuries, the first step consists to elaborate the elementary degradation mechanisms. Thus, electron paramagnetic resonance (EPR), Fourier transform infra‐red spectroscopy (FT‐IR), electrospray ionisation‐mass spectrometry (ESI‐MS), and gas mass spectrometry were carried out to identify radicals, chemical modifications, and gases to reach the radio‐oxidative mechanism at doses inferior than 1000 kGy. Degradation mainly occurs at urethane bonds and in polyether soft segments that produces stable oxidative products as formates, alcohols, carboxylic acids and H₂, CO₂ and CO gases. Predominant degradation occurred at polyether soft segments and crosslinking is in competition with scission. On the basis of the results, a mechanism of degradation for aromatic poly(ether‐urethane) is proposed. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 861–878, 2008     

Ellipsometry study of the photo‐oxidation of poly[(2‐methoxy‐5‐hexyloxy)‐ p‐phenylenevinylene]

Poly(p‐phenylenevinylene) (PPV) and its derivatives exhibit strong luminescence, being serious candidates to be used as active layers in organic light‐emitting diodes. However, the structural degradation caused by photo‐oxidation is an obstacle for commercial applications of such materials. Here, we show that spectroscopy ellipsometry is a useful technique to investigate the photo‐oxidation of poly[(2‐methoxy‐5‐hexyloxy)‐p‐phenylenevinylene] (MH‐PPV), a PPV derivative, which emits a red color light. Spectroscopy ellipsometry enables determination of the complex dielectric function—?*(E)—of MH‐PPV thin‐layer films exposed to air, in the 2.1–4.2 eV energy range, as a function of the light exposure time (t_e). By using the Lorentz model to fit the experimental ?*(E) curves, it was inferred that the interactions among polymeric chains increase with t_e. From ?*(E), it is also possible to obtain the complex refractive index, N*(E) = n + ik. At higher energies (where k ? n), n increases from 1.32 to 1.40 with the photo‐oxidation progress. The behavior of n was investigated by using the Lorenz–Lorentz equation, taking into account the contribution for n by the chromophores of MH‐PPV. The effect of photo‐oxidation, mainly due to the replacement of vinyl C?C by the ketone C?O bonds, is confirmed by Fourier transform infrared measurements, an effect that reduces the average effective polymer conjugation length. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1033–1041, 2004     

Identification of leucine-enkephalin radical oxidation products by liquid chromatography tandem mass spectrometry

The oxidation of the peptide leucine-enkephalin (YGGFL) induced by the hydroxyl radical (HO*), formed under Fenton-like conditions [Cu (II)/H(2)O(2)], was studied and monitored by LC-MS. The oxidation products identified included products resultant from (a) the insertion of oxygen atoms (1-5), (b) peptide backbone cleavage (short-chain products formed by diamide pathway) and (c) radical-radical crosslinking reactions. In order to identify the modified residues, LC-MS/MS spectra were obtained. The insertion of oxygen atoms into the peptide originated hydroxide, di-hydroxide and/or hydroperoxide derivatives. In addition it was found that the aromatic amino acids are most susceptible to being hydroxylated, while the aliphatic amino acids are more prone to forming hydroperoxides. Oxidation products with double bonds were also identified. The short chain products resulted from the alpha-carbon radical of terminal amino acids (Tyr and Leu). Products resulting from cross-linking reactions between intact carbon-centered peptide radical (with and without one HO group) and a side chain radical (*C(7)H(7)O) were identified. It was found that, although all amino acids residues of the peptide undergo modifications, the N-terminal seems to be prone to oxidative modifications under these conditions.     

Micro‐FT‐IR study of stretching a single filament: Polymorphic transition in nylon 6

The polymorphic transition (γ → α conversion) in a single nylon 6 filament under stretching has been explored for the first time by using micro‐FT‐IR spectroscopy. The content of γ‐form deceases with straining while the amount of α‐form gradually increases, suggesting γ → α conversion. A two‐step mechanism, that is, melting and recrystallization, seems pertinent for the γ → α conversion considering that the γ‐form shows somewhat reversible and the α‐form keeps nearly intact upon unloading. Moreover, stress‐induced γ → α conversion at large strain can be well correlated with the molecular orientation in the amorphous phase and thus a serial arrangement between the γ crystals and amorphous phase along the stretching direction is proposed. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 898–902, 2009     

Geometrical parameters,vibrational wavenumbers,and relationships established with six difluorobenzonitriles

The geometry, vibrational wavenumbers, and thermodynamical parameters have been calculated using density functional methods (DFT) for benzonitrile (BN) and the six difluorobenzonitriles (DFBNs) of the series. The results were compared with the available experimental data, and correlations were established for the ? C?N and C? F moieties between the natural atomic charges and the geometrical parameters of the compounds. These relations were found as linear or slightly parabolic in most cases. Investigations were carried out to examine the effect of substituents on structural deformations and other properties. Correlations were also determined with the stretching vibrations. Other general conclusions have also been drawn. © 2006 Wiley Periodicals, Inc. Int J Quantum Chem, 2007     

Physico‐Chemical Studies on Cu(II) Complexes of Acrylate Chelating Polymers

Abstract

Metal chelating polymers containing amide and carboxylic groups were prepared by gamma‐radiation polymerization of acrylic acid (AA) monomers in the presence of polyacrylamide (PAM). The resins obtained were loaded by copper ions and characterized by FT‐IR spectroscopy, electron spin resonance (ESR), thermogravimetric analysis (TGA), and differential scanning calorimetery (DSC). The IR spectra indicated a lower frequencies shift in the carbonyl bands due to copper ion chelation with carbonyl groups in the polymer resins. Also, the IR spectra reveal a splitting in the band at 3600–3200?cm^?1 that due to the coordination of the NH and OH groups with copper ions. The ESR spectrum was anisotropic with hyperfine structure having the following values 2.3808 and 2.07218 for g _∥ and g _⊥, respectively. These spectra for copper ions have square planar coordination with two nitrogen and two oxygen atoms. TGA and DSC studies show that radiation crosslinking and complexation with copper ion increase the thermal stability of PAM–AA resins. Meanwhile, resin complexes with copper ion showed a higher thermal stability than pure resin. The increase in thermal stability may be correlated with the metal ions coordination with NH and OH groups; this coordination prevents the splitting of ammonia and water molecules. Also, the metal ions providing a coordination crosslink between polymer chains could increase thermal stability.     

Switchable selectivity during oxidation of anilines in a ball mill

A solvent-free method for the direct oxidation of anilines to the corresponding azo and azoxy homocoupling products by using a planetary ball mill was developed. Various oxidants and grinding auxiliaries were tested and a variety of substituted anilines were investigated. It was possible to form chemoselectively either azo, azoxy, or the nitro compounds from reaction of aromatic anilines. The selectivity of the solvent-free reaction is switchable by applying a combination of oxidant and grinding auxiliary. Furthermore, a comparison with other methods of energy input (microwave, classical heating, and ultrasound) highlighted the advantages of the ball mill approach and its high energy efficiency.     

Influence of the network chain orientation on the fracture toughness of a mesogenic epoxy resin modified with CTBN

A biphenol‐type epoxy resin, which had a mesogenic group in the backbone moiety, was modified with carboxy‐terminated butadiene acrylonitrile copolymer (CTBN) as a reactive elastomer, and its fracture toughness was measured. With the addition of CTBN, the fracture toughness of the biphenol‐type epoxy resin significantly increased and became significantly higher than that of a bisphenol A‐type epoxy resin modified with CTBN. The network chain orientation in the cured biphenol‐type epoxy resin system was clearly observed during the fracture process with polarized microscopy Fourier transform infrared measurements, although such a phenomenon was not observed in the bisphenol A‐type epoxy resin system. The high toughness of the cured biphenol‐type system was clearly due to the consumption of the mechanical energy by a large deformation of the matrix resin due to the orientation of the network chains during the fracture process. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1198–1209, 2003     

Real-time quantitative analysis of volatile products generated during solid-state polypropylene thermal oxidation

Analysis of volatile organic compounds (VOCs) during PP thermal oxidation under three oxygen partial pressures (0%, 21% and 100% of atmospheric pressure) at 140 °C was performed by proton transfer reaction coupled with Fourier transform ion cyclotron resonance mass spectrometry. Six main VOCs were identified: acetone, acetic acid, 2,4-pentanedione, acetaldehyde, formaldehyde and methyl acrolein. Their formation was shown to obey two main reaction pathways, both involving methyne units as driving oxidation sites: (i) the widely accepted chain scission mechanism of tertiary alkoxy radicals, which generates primary radicals undergoing secondary reactions leading to the oxidation of methylene units; (ii) the chain scission mechanism occurring on tertiary alkyl radical, which is proposed here as a realistic path leading to methyl acrolein. The relative proportions of the six main VOCs depend on the oxygen partial pressure, which mostly impacts the oxidation of methylene units rather than the competition between the two previous paths.     

Synthesis,characterization, and aqueous self‐assembly of amphiphilic poly(ethylene oxide)‐functionalized hyperbranched fluoropolymers

Complex amphiphilic polymers were synthesized via core‐first polymerization followed by alkylation‐based grafting of poly(ethylene oxide) (PEO). Inimer 1‐(4′‐(bromomethyl)benzyloxy)‐2,3,5,6‐tetrafluoro‐4‐vinylbenzene was synthesized and subjected to atom transfer radical self‐condensing vinyl polymerization to afford hyperbranched fluoropolymer (HBFP) as the hydrophobic core component with a number‐averaged molecular weight of 29 kDa and polydispersity index of 2.1. The alkyl halide chain ends on the HBFP were allowed to undergo reaction with monomethoxy‐terminated poly(ethylene oxide) amine (PEO_x‐NH₂) at different grafting numbers and PEO chain lengths to afford PEO‐functionalized HBFPs [(PEO_x)_y‐HBFPs], with x = 15 while y = 16, 22, or 29, x = 44 while y = 16, and x = 112 while y = 16. The amphiphilic, grafted block copolymers were found to aggregate in aqueous solution to give micelles with number‐averaged diameters (D_av) of 12–28 nm, as measured by transmission electron microscopy (TEM). An increase of the PEO:HBFP ratio, by increase in either the grafting densities (y values) or the chain lengths (x values), led to decreased TEM‐measured diameters. These complex, amphiphilic (PEO_x)_y‐HBFPs, with tunable sizes, might find potential applications as nanoscopic biomedical devices, such as drug delivery vehicles and ¹⁹F magnetic resonance imaging agents. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3487–3496, 2010     

Structure elucidation of thermal degradation products of amlodipine

Thermal degradation of amlodipine base causes intramolecular reactions affording three cyclic products, referred to as AMLDEG-I, AMLDEG-II, and AMLDEG-III, respectively. AMLDEG-I is a cyclized product formed by intramolecular elimination of ammonia from amlodipine. AMLDEG-II is a positional isomer of AMLDEG-I. AMLDEG-III is also intramolecular cyclisation product. The three degradation products were isolated by column chromatography and characterized by FT-IR and 1H and 13C NMR spectroscopy data. The AMLDEG-III was crystallized and its structure was solved by single crystal X-ray diffraction (SXRD).     

Reflection–absorption infrared spectroscopy investigation of the crystallization kinetics of poly(ethylene terephthalate) ultrathin films

Reflection–absorption infrared spectroscopy was used to study the crystallization behavior of poly(ethylene terephthalate) (PET) ultrathin films. The crystallinity of ultrathin films was estimated by the fraction of trans conformers of PET. The isothermal and nonisothermal crystallization kinetics of ultrathin films with different thicknesses were investigated. The thinner PET film showed slower kinetics during isothermal crystallization than the thicker film. Moreover, the final crystallinity of films with various thicknesses were reduced with decreasing thickness. An Avrami equation was used to fit the acquired results. The Avrami exponents decreased with the film thickness. As for the nonisothermal crystallization, the cold‐crystallization starting temperature shifted to a lower temperature as the film thickness increased. The influence of the substrate on the crystallization kinetics of the films was also studied. The half‐crystallization times and final crystallinities of ultrathin films adsorbed onto a self‐assembled‐monolayer‐treated surface and an untreated substrate were clearly different, although their thickness dependence was similar. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4440–4447, 2004     

Effect of low‐temperature physical aging on the dynamic transitions of atactic polystyrene in the glassy state

The local and cooperative dynamics of atactic PS (a‐PS) were studied by broadband dielectric relaxation spectroscopy (BDRS) and attenuated total reflectance Fourier transform infrared spectroscopy (ATR‐FTIR). The a‐PS has been subjected to thermal rejuvenation and subsequent quenching, short‐term aging (6 weeks), and long‐term aging (1 year) at ambient conditions. Where for the rejuvenated sample only an α‐ and a γ‐relaxation is observed, short‐term aging results in an additional β*‐relaxation that merges with the α‐relaxation at longer aging times. The γ‐relaxation is increasing in intensity and activation energy during aging. The α‐process shows no spectral changes and shift in the relaxation time upon aging. This may be attributed to a possible erasure of history of the material during the temperature‐sweep mode measurement. Fourier transform infrared spectroscopy (FTIR) results suggest that the energetically favorable trans‐trans (tt) conformers are increased in population with aging. © 2019 The Authors. Journal of Polymer Science Part B: Polymer Physics published by Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1394–1401     

High‐Throughput Method for Determining Modulus of Polymer Blends

Summary: A method for rapidly determining the modulus of polymer blends was developed. A polymer blend gradient library of poly(L ‐lactic acid) (PLLA) and poly(D ,L ‐lactic acid) (PDLLA) was created in the form of a strip‐shaped film and characterized with FTIR microspectroscopy. Nanoindentation measurements were made along the gradients to obtain modulus data over a wide range of PLLA‐PDLLA blend compositions. This novel, high‐throughput approach to material characterization provides engineers with a technique to accelerate the development of materials.

Deposition of the polymer composition gradient.