Fabrication and characterization of UV‐crosslinkable thermoresponsive composite fibers with magnetic properties

Crosslinking magnetic thermoresponsive composite (MTC) fiber mats were fabricated by electrospinning process and followed by UV curing. Thermoresponsive poly‐(N‐isopropylacrylamide) (PNIPAAm) and magnetic Fe₃O₄ were firstly synthesized by redox‐initiated polymerization and co‐precipitation, respectively. A crosslinking agent (dipentaerythritol hexylacrylate) and photoinitiator for providing crosslinking ability were then mixed with PNIPAAm and Fe₃O₄ in ethanol as the electrospinning solution. After electrospinning and subsequent UV irradiation, the MTC fiber mats were thus obtained. Thermoresponsivity of the MTC fibers was measured by both DSC and swelling test. MTC fiber mat exhibited better water‐absorption capability and thermoresponsivity than corresponding film. Morphological analysis was observed by SEM and TEM, and the magnetic property was measured by SQUID. The thermoresponsive magnetic behavior of MTC fiber mat in water was observed under various temperatures and magnetic fields. Vitamin B₁₂ used as a model drug was loaded in the MTC fiber mats and the drug‐release behavior was then studied. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2152–2162     

Thermoresponsive conductive polymer composite thin film and fiber mat: Crosslinked PEDOT:PSS and P(NIPAAm‐co‐NMA) composite

The thermoresponsive conductive composite (TCC) thin films and fiber mats, whose electrical property changed with temperature, were fabricated successfully. The thermocrosslinkable and thermoresponsive copolymer, poly(N‐isopropyl acrylamide‐co‐N‐methylolacrylamide) (PNN), was synthesized. The TCC thin film and fiber mat were fabricated by spin coating and electrospinning process of PEDOT:PSS/PNN solutions, respectively. After thermocrosslinking and doping by DMSO, the composite thin films and fiber mats were obtained. Fibrous structures of TCC fiber mats were observed by SEM. The surface resistance and conductivity of composites were measured. The thermoresponsivity and swelling ratio of TCCs were also studied. The thermoresponsive conductive property was analyzed by measuring the surface resistance of TCCs in water bath under various temperatures from 20 to 50 °C. With the increase of temperature, the TCCs shrank to be dense structure and showed lower surface resistance. The TCC fibers mat exhibited greater sensitivity to temperature than thin film owing to its fibrous structure. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1078–1087     

Preparation and properties of thermoresponsive and conductive composite fibers with core‐sheath structure

In this research, thermoresponsive and conductive fibers with core‐sheath structure were fabricated by coaxial electrospinning. For preparing the spinning sheath solution, poly‐(N‐isopropylacrylamide‐co‐N‐methylolacrylamide) (PNN) copolymer having thermoresponsive and cross‐linkable properties was synthesized by free‐radical polymerization using redox initiators; it was then mixed with the conductive poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) at different weight ratios in water. On the other hand, poly(butyl acrylate‐co‐styrene) (PBS) copolymer synthesized by emulsion polymerization was dissolved in chloroform and used as the spinning core solution. After electrospinning, the fibers were treated at 110 °C for 1 h to cross‐link the PNN portion in the sheath for strengthening the fibers. Well‐defined core‐sheath fibers were observed from SEM pictures; the outside and inside (core) diameters were 568 ± 24 and 290 ± 40 nm, respectively, as determined from TEM pictures. The fiber mats were further doped by DMSO to enhance their conductivity. For the fiber mat with the weight ratio of PEDOT:PSS/PNN at 0.20 in the sheath, its surface conductivity could reach 29.4 S/cm. In addition, the fiber mats exhibited thermoresponsive properties that both swelling ratio and electric resistance decreased with temperature. Furthermore, the fiber mats exhibited improved flexibility as evaluated via bending test. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1299–1307     

Electrospinning of polyurethane/organically modified montmorillonite nanocomposites

Polyurethane/organically modified montmorillonite (PU/O‐MMT) nanocomposites were electrospun and the effect of O‐MMT on the morphology and physical properties of the PU/O‐MMT nanofiber mats were investigated for the first time. The average diameters of the PU/O‐MMT nanofibers were ranged from 150 to 410 nm. The conductivities of the PU/O‐MMT solutions were linearly increased with increasing the content of O‐MMT, which caused a decrease in the average diameters of the PU/O‐MMT nanofibers. The as‐electrospun PU and PU/O‐MMT nanofibers were not microphase separated. The exfoliated MMT layers were well distributed within the PU/O‐MMT nanofibers and oriented along the fiber axis. When the PU/O‐MMT nanofibers were annealed, the exfoliated MMT layers hindered the microphase separation of the PU. The electrospinning of PU/O‐MMT nanocomposites resulted in PU nanofiber mats with improved Young's modulus and tensile strength. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3171–3177, 2005     

Large‐scale aligned fiber mats prepared by salt‐induced pulse electrospinning

In this article, a new large‐scale aligned fiber mats formation method called salt‐induced pulse electrospinning was developed. By electrospinning salted solution in a humid environment, traditional continuous electrospinning changed into pulse electrospinning and aligned fibers were thus formed. The possible mechanisms for the occurrence of salt‐induced pulse electrospinning and the formation of fiber alignment were studied. The continuous electrospinning changing into the pulse electrospinning was due to the change of viscosity and conductivity of salted polymer solution in a wet electrospinning condition. Fishing net‐shaped whipping region of the electrospinning jet during pulse electrospinning process was considered as the key factor for the formation of fiber alignment. The mechanical properties of the aligned fiber mat increased significantly compared with that of the random fiber mat. This aligned fiber preparation method only requires a very low rotating drum speed as the receiver and can produce large‐scale aligned fiber mats for many applications. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Electrospun poly(aniline‐co‐ethyl 3‐aminobenzoate)/poly(lactic acid) nanofibers and their potential in biomedical applications

Poly(aniline‐co‐ethyl 3‐aminobenzoate) (3EABPANI) copolymer was blended with poly(lactic acid) (PLA) and co‐electrospun into nanofibers to investigate its potential in biomedical applications. The relationship between electrospinning parameters and fiber diameter has been investigated. The mechanical and electrical properties of electrospun 3EABPANI‐PLA nanofibers were also evaluated. To assess cell morphology and biocompatibility, nanofibrous mats of pure PLA and 3EABPANI‐PLA were deposited on glass substrates and the proliferation of COS‐1 fibroblast cells on the nanofibrous polymer surfaces determined. The nanofibrous 3EABPANI‐PLA blends were easily fabricated by electrospinning and gave enhanced mammalian cell growth, antioxidant and antimicrobial capabilities, and electrical conductivity. These results suggest that 3EABPANI‐PLA nanofibrous blends might provide a novel bioactive conductive material for biomedical applications. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Controlling electrospun nanofiber morphology and mechanical properties using humidity

Electrospinning is a fiber spinning technique used to produce nanoscale polymeric fibers with superior interconnectivity and specific surface area. The fiber diameter, surface morphology, and mechanical strength are important properties of electrospun fibers that can be tuned for diverse applications. In this study, the authors investigate how the humidity during electrospinning influences these specific properties of the fiber mat. Using two previously uninvestigated polymers, poly(acrylonitrile) (PAN) and polysulfone (PSU) dissolved in N,N‐Dimethylformamide (DMF), experimental results show that increasing humidity during spinning causes an increase in fiber diameter and a decrease in mechanical strength. Moreover, surface features such as roughness or pores become evident when electrospinning in an atmosphere with high relative humidity (RH). However, PAN and PSU fibers are affected differently. PAN has a narrower distribution of fiber diameter regardless of the RH, whereas PSU has a wider and more bimodal distribution under high RH. In addition, PSU fibers spun at high humidity exhibit surface pores and higher specific surface area whereas PAN fibers exhibit an increased surface roughness but no visible pores. These fiber morphologies are caused by a complex interaction between the nonsolvent (water), the hygroscopic solvent (DMF), and the polymer. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Preparation of submicron‐scale,electrospun cellulose fibers via direct dissolution

Cellulose nonwoven mats of submicron‐sized fibers (150 nm–500 nm in diameter) were obtained by electrospinning cellulose solutions. A solvent system based on lithium chloride (LiCl) and N,N‐dimethylacetamide (DMAc) was used, and the effects of (i) temperature of the collector, (ii) type of collector (aluminum mesh and cellulose filter media), and (iii) postspinning treatment, such as coagulation with water, on the morphology of electrospun fibers were investigated. The scanning electron microscopy (SEM) and X‐ray diffraction studies of as‐spun fibers at room temperature reveal that the morphology of cellulose fibers evolves with time due to moisture absorption and swelling caused by the residual salt and solvent. Although heating the collector greatly enhances the stability of the fiber morphology, the removal of salt by coagulation and DMAc by heating the collector was necessary for the fabrication of dry and stable cellulose fibers with limited moisture absorption and swelling. The presence and removal of the salt before and after coagulation have been identified by electron microprobe and X‐ray diffraction studies. When cellulose filter media is used as a collector, dry and stable fibers were obtained without the coagulation step, and the resulting electrospun fibers exhibit good adhesion to the filter media. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1673–1683, 2005     

Electrospinning of poly(vinylidene fluoride)/dimethylformamide solutions with carbon nanotubes

For conductive carbon nanotube (CN)/polymer composite fibers to be obtained, CNs were incorporated into poly(vinylidene fluoride) (PVDF) in dimethylformamide (DMF) solutions and electrospun to form CN/PVDF fiber mats. The thinnest fiber was 70 nm thick. The percolation threshold for the insulator‐to‐conductor transition was 0.003 wt % CN for CN/PVDF/DMF solutions, 0.015 wt % CN for CN/PVDF spin‐coated films, and 0.04 wt % CN for CN/PVDF electrospun fiber mats. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1572–1577, 2003     

Morphology and physical properties of a novel Ramie‐PU blended nonwoven by electrospinning: The effect of cosolvent ratio

A novel macro/nano blended nonwoven with excellent physical properties was prepared by electrospinning polyurethane (PU) nanofibers onto the surface of ramie webs under different weight ratios of N,N‐dimethylacetamide (DMAc)/acetone cosolvents. The ratio of cosolvents has a significant influence on the morphology, tensile properties, resilience, and thermal properties of the resultant samples. Bead‐free and fine interconnected nanofibers were obtained with an increase of acetone content up to 60 wt%. The total physical properties of the blended nonwovens were optimal for a DMAc/acetone ratio of 40/60, in which the tensile load at break, extension at break and Young's modulus were 441, 54, and 256% higher than that of pure ramie web, respectively. The resilience of the blended nonwovens was ～20% higher than that of nonblended ramie web. The significant improvement of physical properties may be due to the good connection between PU nanofiber membranes and ramie webs and the molecular chain structure differences, interconnected structural differences, and high extensibility of PU nanofibers, according to the results of crystallization by differential scanning calorimetry (DSC) and morphological observation by scanning electronic microscopy (SEM). © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1–14, 2010     

Synthesis and mechanical properties of para‐aramid nanofibers

Scalable, bottom‐up chemical synthesis and electrospinning of novel Cl‐substituted poly(para‐phenylene terephthalamide) (PPTA) nanofibers are herein reported. To achieve Cl‐PPTA nanofibers, the chemical reaction between the monomers was precisely controlled, and dissolution of the polymer into solvent was tailored to enable anisotropic solution formation and sufficient entanglement molecular weight. Electrospinning processing parameters were studied to understand their effects on fiber formation and mat morphology and then optimized to yield consistently high quality fibers. Importantly, the control of relative humidity during the fiber formation process was found to be critical, likely because water promotes hydrogen bond formation between the PPTA chains. The fiber and mat morphologies resulting from different combinations of chemistry and spinning conditions were observed using scanning electron microscopy, and observations were used as inputs to the optimization process. Tensile properties of single Cl‐PPTA nanofibers were characterized for the first time using a nanomanipulator mounted inside a scanning electron microscope (SEM), and fiber moduli measuring up to 70 GPa, and strengths exceeding 1 GPa were achieved. Given the excellent mechanical properties measured for the nanofibers, this chemical synthesis procedure and electrospinning protocol appear to be a promising route for producing a new class of nanofibers with ultrahigh strength and stiffness. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 563–573     

Crosslinking polymerization leading to interpenetrating polymer network formation. II. Polyaddition crosslinking reactions of poly(methyl methacrylate‐co‐2‐methacryloyloxyethyl isocyanate) with various diols

As part of our continuing studies concerned with the elucidation of the crosslinking polymerization mechanism leading to interpenetrating polymer network (IPN) formation, in which IPNs consist of both polymethacrylates and polyurethane (PU) networks, this article explores the polyaddition crosslinking reactions of multifunctional poly(methyl methacrylate‐co‐2‐methacryloyloxyethyl isocyanate) [poly(MMA‐co‐MOI)] [MMA/MOI = 90/10] with various diols leading to PU network formation. Thus, the equimolar polyaddition crosslinking reactions of poly(MMA‐co‐MOI) with ethylene glycol (EG), 1,6‐hexane diol, and 1,10‐decane diol (DD) were carried out in N‐methyl pyrrolidone at a 0.25 mol/L isocyanate group concentration at 80 °C. The second‐order rate constants decreased from EG to DD. The deviation of the actual gel point from the theoretical one was smaller from EG to DD. The intrinsic viscosity of resulting prepolymer demonstrated almost no variation with progressing polymerization for the EG system, whereas it gradually increased with conversion for the DD system. Close to the gel point conversion it increased rather drastically for both systems. The swelling ratio of resulting gel was higher from EG to DD. These are discussed mechanistically in terms of the significant occurrence of intramolecular cyclization and intramolecular crosslinking reactions leading to shrinkage of the molecular size. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3243–3248, 2003     

Effect of constrained annealing on the mechanical properties of electrospun poly(ethylene oxide) webs containing multiwalled carbon nanotubes

In this work, flexible nanofibrous membranes (mats) of poly(ethylene oxide) (PEO) with and without multiwall carbon nanotubes (MWNTs) were fabricated by electrospinning. The effects of annealing and MWNT concentration on mat morphology, MWNT dispersion within the nanofibers, and the mechanical properties of electrospun mats were studied. Annealing temperatures ranged from 60 °C to 64 °C [near the melting temperature (64 °C via differential scanning calorimetry)] for 4 minutes. Samples were annealed with and without applied tension (constrained and unconstrained annealing). Annealing at the highest temperature (64 °C), before the loss of fibrous morphology, significantly improved fiber–fiber bonding and therefore the tensile strength of the mats. Compared with unconstrained annealing, constrained annealing introduced fiber alignment (and therefore molecular orientation) along the tensile axis (direction of constraint) during annealing and resulted in a significant increase in modulus for all samples (with and without MWNTs). The use of constrained annealing may be a facile approach to enhance modulus in nanofibrous mats while maintaining high porosity. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 787–796     

Development of the morphology and crystalline state due to hybridization of reinforced toughened nylon containing a liquid‐crystalline polymer

A hybrid composite consisting of rubber‐toughened nylon‐6,6, short glass fibers, and a thermotropic liquid‐crystalline polymers (LCP) was investigated by the LCP content being varied. The thermal behavior, morphology, and crystallization behavior due to hybridization were studied by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, and wide‐angle X‐ray scattering (WAXS). DSC results indicated that the crystallinity of the glass‐fiber‐reinforced toughened nylon‐6,6 was reduced by LCP addition, particularly 5–10 wt % LCP. DMA data showed that the miscibility between the blended components was maximum at the 5 wt % LCP composition, and the miscibility decreased with increasing LCP content. SEM photomicrographs revealed information consistent with the thermal behavior on miscibility. It was also observed that the 10 wt % LCP composition showed predominantly an amorphous character with FTIR and WAXS. WAXS results indicated that LCP hybridization increased the interplanar spacing of the hydrogen‐bonded sheets of the nylon crystals rather than the spacing between the hydrogen‐bonded chains. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 549–559, 2003     

Influence of solvents properties on morphology of electrospun polyurethane nanofiber mats

Segmented polyurethane (SPU) nanofiber mats were prepared by electrospinning technique using the combination of four different solvents viz. tetrahydrofuran, N,N′‐dimethyl formamide, N,N′‐dimethyl acetamide, and dimethyl sulfoxide. Morphology of the electrospun nanofibers was examined by field emission scanning electron microscope. Experimental results revealed that the morphologies of polyurethane nanofiber mats have been changed significantly with the solvent selection for the electrospinning. It was observed that the diameters and morphology of the SPU nanofibers were influenced greatly by the use of combination of solvents. The uniform polyurethane nanofibers without beads or curls could be prepared by electrospinning through the selection of combination of good conductive and good volatile solvent viz. 7.5 wt/v% of SPU in N,N′‐dimethyl formamide/tetrahydrofuran (30 : 70 v/v) solutions at 20 kV applied voltages and volume flow rate of 1 ml/min. On the basis of the results obtained from this investigation, it has been established that solvent selection is one of the driving factors for controlling the morphology of the polyurethane electrospun nanofiber mats. The well‐controlled morphology of electrospun polyurethane nanofiber mats could be useful for many potential industrial applications such as in biomedical, smart textiles, nanofiltration, and sensors. Copyright © 2013 John Wiley & Sons, Ltd.     

Rheological and mechanical properties of epoxy/polyurethane blends initiated by N‐benzylpyrazinium hexafluoroantimonate salt

In this work the cure behavior and rheological and mechanical interfacial properties of the diglycidylether of bisphenol A (DGEBA)/polyurethane (PU) blend system, initiated by 1 wt % N‐benzylpyrazinium hexafluoroantimonate as a latent thermal catalyst, were investigated. To characterize the mechanical interfacial properties of the system, the critical stress intensity factor (K_IC) was calculated with a single‐edge‐notched beam (SEN) beam fracture toughness test. And an impact test was performed at room and cryogenic temperatures to determine the performance of PU at room and low‐temperatures, respectively. As a result, the E_c of the blend system was increased with increasing PU content, showing a maximum value at 30 wt % PU, which was in good agreement with the mechanical properties of the blend system. Consequently, these results could be explained by the improvement that occurred in intermolecular hydrogen bonding between the hydroxyl group in EP and the isocyanate group in PU, resulting in increased compatibility of the components within the interpenetrating polymer networks. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3841–3848, 2004     

Photo and Thermal Cured Silicon‐Containing Diethynylbenzene Fibers via Melt Electrospinning with Enhanced Thermal Stability

An inorganic–organic hybrid material, poly(dimethylsilylene ethynylenephenyleneethynylene) (PMSEPE), was synthesized in a mild condition and its microfiber was successfully produced by melt electrospinning. The electrospinning parameters, which affected the morphology and diameter of fibers, were well investigated. To maintain the fiber structure at thermal cured temperature (above melting point), the PMSEPE fibers were enhanced via thiol‐yne photo polymerization. Followed by the thermal curing reaction, the heat‐resistance and mechanical properties of fibers were enhanced. The mechanism of two‐step curing was explored and confirmed by means of Fourier transform infrared, differential scanning calorimetry, and X‐ray photoelectron spectroscopy (XPS). Thermaogravimetric analysis and scanning electron microscopy results show that after carbonization at 800 °C, the two‐step cured fibers had only a small weight loss (20%) and the fibers can still maintain the original morphology. Moreover, the two‐step cured fiber exhibited a high tensile strength (55.4 MPa) and a small elongation at break (0.02%). All the results indicate that the fibers could be applied as fiber‐reinforced materials. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2815–2823     

Novel routes to epoxy functionalization of PHA‐based electrospun scaffolds as ways to improve cell adhesion

Straightforward and versatile routes to functionalize the surface of poly(3‐hydroxyalkanoate) (PHA) electrospun fibers for improving cell compatibility are reported under relatively mild conditions. The modification of nanofibrous PHAs is implemented through two different methodologies to introduce epoxy groups on the fiber surface: (1) preliminary chemical conversion of double bonds of unsaturated PHAs into epoxy groups, followed by electrospinning of epoxy‐functionalized PHAs blended with nonfunctionalized PHAs, (2) electrospinning of nonfunctionalized PHAs, followed by glycidyl methacrylate grafting polymerization under UV irradiation. The latter approach offers the advantage to generate a higher density of epoxy groups on the fiber surface. The successful modification is confirmed by ATR‐FTIR, Raman spectroscopy, and TGA measurements. Further, epoxy groups are chemically modified via the attachment of a peptide sequence such as Arg‐Gly‐Asp (RGD), to obtain biomimetic scaffolds. Human mesenchymal stromal cells exhibit a better adhesion on the latter scaffolds than that on nonfunctionalized PHA mats. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 816–824     

Thermoplastic polyurethane/silica nanocomposite fibers by electrospinning

Thermoplastic polyurethane/silica nanocomposite fibers with good mechanical properties were prepared by electrospinning, using colloidal silica as the source of silica and dimethyl formamide as the solvent. The fiber morphology was examined by field emission scanning electron microscopy. The average fiber diameter is about 0.8 μm with 0–10 wt % silica, and silica nanoparticles were observed on all fiber surfaces. X‐ray photoelectron spectroscopy analysis of Si in combination with transmission electron microscopy observation suggest that silica nanoparticles have a fairly uniform distribution in the fibers rather than enriching on the fiber surfaces. Tensile tests show that the incorporation of silica nanoparticles can bring about a significant reinforcing effect without decreasing the ductility. The reinforcing effect is further confirmed by dynamic mechanical analysis. The thermoplastic polyurethane/silica composite fiber mats can adsorb gold nanoparticles after further treatment with 3‐aminopropyltriethoxysilane, demonstrating that the composite fibers could be used as functional fibers by using the properties of silica nanoparticles. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Preparation of PVA／H3PW12O40 Fiber Mats

Poly(vinyl alcohol) (PVA) fiber mats containing 20 and 80wt% H3PW12O40 were prepared by using electrospinning technique. The fiber mats were characterized by IR, XRD spectra and scanning electron microscope (SEM). The diameter of the fiber mats is ca. 400nm.