纳米金修饰的碳纤维超微电极在高浓度抗坏血酸体系中选择性测定多巴胺

将柠檬酸三钠与硼氢化钠还原氯金酸制备纳米金颗粒,采用一步恒电位沉积的方法在碳纤维超微电极上沉积纳米金颗粒,并对电极进行电化学表征。分别对100μmol/L DA、1mmol/L AA在该电极上修饰前后的电化学行为进行了研究,结果表明在浓度为1 mmol/L抗坏血酸共存下,DA的浓度(0. 1～10μmol/L)与氧化峰电流成正比,线性回归方程为Ip(μA)=200 c(μmol/L)+2×10~(-4),相关系数R~2=0. 9979,线性范围0. 1～10μmol/L,检出限为1. 28×10~(-2)μmol/L (S/N=3)。方法可用于较高浓度抗坏血酸共存下对多巴胺的选择性测定。     

碳纳米管修饰碳纤维超微圆柱电极的研制与应用

制作了碳纳米管修饰碳纤维组合电极(EUME-CNT),研究了木犀草素在EUME-CNT上的电化学行为,并且通过优化测定参数,建立了木犀草素的电化学分析方法。检出限达到4×10-7mol/L,线性范围为6×10-7~1×10-5mol/L。     

纳米金修饰玻碳电极对鸟嘌呤的催化氧化

采用电化学沉积法制备了纳米金修饰玻碳电极,并用循环伏安法和电化学阻抗法进行了表征,以此建立了一种直接测定鸟嘌呤的电分析方法。在磷酸盐缓冲溶液(pH 6.0)中,研究了鸟嘌呤在纳米金修饰电极上的电化学行为,实验结果表明,纳米金修饰电极可以增强鸟嘌呤在电极表面的吸附,并加快鸟嘌呤在电极表面的电子传输,使其电化学信号明显增大,检测灵敏度大大提高,该修饰电极对鸟嘌呤表现出良好的电催化性能。在优化实验条件下对鸟嘌呤进行测定,方法的线性范围为8.0×10-7~6.0×10-5mol/L,检出限为1.0×10-8mol/L,在鸟嘌呤浓度为1.0×10-5mol/L时测得RSD(n=10)为2.5%。     

纳米金/三聚氰胺修饰电极检测亚硝酸盐

采用电聚合方法制备三聚氰胺(MA)膜修饰玻碳电极(GCE),然后采用原位恒电位沉积法制备金纳米颗粒(Au),并将其修饰于膜电极表面,制得纳米金/三聚氰胺修饰玻碳电极(Au/MA/GCE)。用扫描电子显微镜(SEM)对修饰电极进行表面形貌和元素成分分析。用循环伏安法研究亚硝酸根(NO2-)在该修饰电极上的电化学行为发现,NO2-在0.85 V出现一灵敏的氧化峰。在优化的实验条件下,NO2-在1.0×10-5～1.0×10-3mol/L浓度范围内与其氧化峰电流成线性关系,检测下限为8.9×10-7mol/L。将修饰电极用于实际样品中NO2-的检测,效果良好。     

纳米金修饰玻碳电极对甲醛的电催化氧化

利用电沉积方法制备了纳米金(nano-gold,NG)修饰玻碳电极(GCE)。在碱性介质中该电极对甲醛有较好的催化氧化作用,使甲醛在0.65 V左右出现一个氧化峰,依此测定甲醛的含量。通过实验确定了纳米金的沉积电位和沉积时间,以及纳米金对甲醛的催化氧化所需的底液。该法测定甲醛的线性范围为1~1 000μg/L,检出限为0.3 mg/L。加标回收率为98.5%~101.8%。     

碳纤维超微电极负载金纳米粒子高灵敏检测木犀草素

该研究建立了木犀草素（Lu）的电化学检测方法,通过柠檬酸三钠还原氯金酸制备了纳米金（AuNPs）,并运用一步恒电位沉积法在碳纤维超微电极（CFME）表面电沉积纳米金,研制了一种简单、灵敏检测木犀草素的电化学传感器。采用循环伏安（CV）、电化学交流阻抗（EIS）和差分脉冲伏安（DPV）等方法研究CFME修饰前后对Lu电化学氧化反应的催化性能。结果表明,AuNPs/CFME对Lu的电化学响应催化明显,且AuNPs的最佳修饰时间为30 min。Lu的氧化峰电流在0.01～0.10μmol/L和0.10～10μmol/L两个浓度范围内呈良好的线性关系,相关系数（r2）分别为0.994 4和0.995 1,检出限（LOD,S/N=3）为1.58 nmol/L。该传感器制作简单,且稳定性好、灵敏度高、抗干扰能力强,可实现实际样品独一味胶囊中Lu的定量检测,其加标回收率为96.0%～104%,相对标准偏差（RSD）均小于5.0%,在生物微环境中木犀草素定量分析方面具有良好的应用前景。     

碳纤维微电极负载金纳米粒子用于芦荟多糖的在体动态监测

建立了一种对活体芦荟储水凝胶组织中芦荟多糖进行在体实时动态检测的电化学方法. 通过在活体芦荟植株凝胶中嵌入高灵敏度的纳米金粒子修饰的碳纤维微电极, 对不同光照条件下芦荟植株中的芦荟多糖进行在体动态监测, 进而评价植株应激外界环境下芦荟多糖含量的实时变化. 实验结果表明, 纳米金粒子修饰的碳纤维微电极对芦荟储水凝胶组织中芦荟多糖具有显著的电催化活性, 不同光照环境下生长的芦荟植株中芦荟多糖含量的动态变化具有显著的统计学差异. 该修饰电极可用于芦荟植株中芦荟多糖动态变化的在体实时监测, 使电化学检测方法有望成为监测植物光合作用程度的一种快捷检测手段.     

纳米金修饰玻碳电极测定邻苯二酚

采用恒电位沉积方法将HAuCl4直接还原成纳米金并修饰于玻碳电极表面,制备了对邻苯二酚具有电催化氧化作用的纳米金修饰电极。邻苯二酚在该修饰电极上发生一可逆的氧化还原反应。在磷酸盐缓冲溶液(pH 7.5)中,当邻苯二酚的浓度为3.0×10-3mol.L-1时,与裸玻碳电极相比,其Epa负位移了170 mV,Epc正位移了50 mV,ΔE下降为60 mV,且峰电流显著增大,氧化峰电流与邻苯二酚浓度在5.0×10-6~4.2×10-3mol.L-1范围内呈线性关系,相关系数为0.997 6,检出限(3σ)为5.0×10-7mol.L-1。在浓度为5.0×10-4mol.L-1测得RSD(n=10)为2.9%,回收率在98.0%~101.0%之间。     

多贝斯在纳米金修饰玻碳电极上的电化学行为与测定

采用循环伏安法将纳米金电沉积于玻碳电极表面,制备了纳米金修饰玻碳电极(NG/GCE).在0.05 mol/L H2SO4溶液中,用循环伏安法研究了多贝斯在NG/GCE上的电化学行为.结果表明,NG/GCE对多贝斯的氧化还原反应有明显的电催化作用.建立了测定多贝斯的新方法,用方波伏安法测得多贝斯的氧化峰电流与其浓度在4....     

纳米金/丝素复合膜修饰电极制备及对对苯二酚的电催化作用

将丝素还原HAuCl4制备的纳米金/丝素溶胶修饰在金电极表面制备了纳米金/丝素复合膜修饰电极,用于对苯二酚的催化氧化。实验表明,该修饰电极具有很好的电化学性能,在pH3.55磷酸盐缓冲溶液中以该修饰电极对对苯二酚进行检测,对苯二酚在4.0×10-6~1.0×10-4mol/L浓度范围内,其氧化峰电流与浓度呈良好的线性关系,其线性回归方程为i(μA)=0.2614 5.3539c,r=0.9995;检出限为2.0×10-7mol/L,灵敏度良好,用于实际样品分析,结果令人满意。     

反相高效液相色谱法同时测定决明子中芦荟大黄素和大黄素

用反相高效液相色谱法分离并测定了决明子中芦荟大黄素和大黄素，建立了该中药中芦荟大黄素、大黄素分离、测定的色谱方法。色谱条件：ＯＤＳ柱，甲醇－水（８０∶２０Ｖ／Ｖ）为流动相，检测波长２２３ｎｍ。本研究为决明子的质量评价提供了科学依据。     

碳纤维微电极负载金纳米粒子用于绿茶中儿茶素的检测

本文开发了基于纳米金修饰的碳纤维超微电极(CFME)用于儿茶素的定量检测。通过使用柠檬酸三钠还原氯金酸制得纳米金粒子(AuNPs),采用恒电位电沉积法将纳米金修饰在CFME表面。在pH 2.00的Tris-HCl缓冲溶液中,采用差分脉冲法和循环伏安法考察了修饰前后电极对儿茶素的电催化性能。结果表明,纳米金修饰电极对儿茶素具有明显的电催化效果。在优化实验条件下,纳米金修饰的碳纤维超微电极(AuNPs/CFME)与儿茶素浓度在1.00×10^-3~10.0μmol/L范围内呈良好的线性关系,且AuNPs/CFME的电化学性能非常稳定,具有良好的重现性。该方法操作简单,准确性高,可用于对儿茶素进行定量检测。     

金纳米粒子/碳纳米管修饰电极对4 壬基酚的电催化氧化及检测研究

制备了金纳米粒子/碳纳米管修饰玻碳电极(AuNPs-CNTs/GCE),采用循环伏安法和线性扫描伏安法研究了4-壬基酚在修饰电极上的电化学行为,并建立了一种灵敏简便地检测4-壬基酚的电化学方法。优化了pH值、扫描速率、富集时间等测定参数,并计算出pH值与氧化峰电压、扫描速率与氧化峰电流之间的数量关系。在pH 10.0的BR缓冲溶液中,4-壬基酚在AuNPs-CNTs/GCE上出现灵敏的氧化峰,氧化电位为0.51 V。与裸玻碳电极(GCE)和单一碳纳米管修饰电极(CNTs/GCE)相比,AuNPs-CNTs/GCE明显提高了4-壬基酚的氧化电流。在优化实验条件下,4-壬基酚的浓度分别在0.05～4μmol/L和6～14μmol/L范围内与氧化峰电流呈良好的线性关系,检出限为0.023μmol/L,对于实际样品测定的回收率为95%～104%。该修饰电极具有良好的重现性和稳定性,可用于环境样品中4-壬基酚的直接检测。     

Characterization and Electrocatalytic Activity of Nanocomposites Consisting of Nanosized Cobalt Tetraaminophenoxy Phthalocyanine,Multi‐walled Carbon Nanotubes and Gold Nanoparticles

Glassy carbon electrodes were modified with composites containing cobalt tetraaminophenoxy phthalocyanine nanoparticles (CoTAPhPc NP ), multi‐walled carbon nanotubes (MWCNT) and gold nanorods (AuNRs). The modified electrodes were studied for their electrocatalytic behavior towards the reduction of hydrogen peroxide. Phthalocyanine nanoparticles significantly improved electron transfer kinetics as compared to phthalocyanines which are not in the nanoparticle form when alone or in the presence of multiwalled carbon nanotubes (MWCNTs). CoTAPhPc NP ‐MWCNT‐GCE proved to be suitable for hydrogen peroxide detection with a catalytic rate constant of 3.45×10³ M^?1 s^?1 and a detection limit of 1.61×10^?7 M. Adsorption Gibbs free energy ΔG^o was found to be ?19.22 kJ mol^?1 for CoTAPhPc NP ‐MWCNT‐GCE.     

纳米金催化Luminol-H_2O_2化学发光体系对异烟肼的测定

碱性条件下,纳米金对Luminol-H2O2化学发光体系有增敏作用,而异烟肼对该化学反应具有强烈的抑制作用。基于此,在优化化学发光反应条件的基础上,提出了一种测定异烟肼的新方法,并对其可能的化学发光机理进行了探讨。该方法测定异烟肼的线性范围为0.005~9.0 mg/L,检出限(3σ)为3.0μg/L,相对标准偏差为3.5%(n=11,ρ=0.2 mg/L)。该法已成功用于药物制剂中异烟肼含量的测定。     

Selective Solid-phase Extraction of Aloe Emodin from Aloe by Molecularly Imprinted Polymers

The extraction and separation of aloe emodin were optimized via selective molecularly imprinted solid-phase extraction. Molecularly imprinted polymer was prepared from the functional monomer, methacrylic acid and a mixture of ethanol/dodecanol(90/10, volume ratio) as porogen. It overcomes the common problems of imprin-ting biological polar compounds and shows high selectivity compared favorably with those of non-imprinted polymer and commercially available C₁₈ and silica cartridges in similar aloe emodin tests. Good linearity was obtained between 0.002 and 2.5 mg/mL(r²=0.998) with relative standard deviations below 3.3%.     

介孔炭/纳米金修饰玻碳电极的制备及其应用研究

制备了介孔炭/纳米金修饰玻碳电极,并对对苯二酚(HQ)在该修饰电极上的电化学行为进行了研究。与HQ在纯介孔炭材料修饰玻碳电极上的电化学响应相比,HQ在该修饰电极上的氧化峰和还原峰电流均大大增加,表明纳米金与介孔炭复合后对HQ具有良好的催化作用。HQ在该修饰电极上经过富集后,峰电流明显增大。采用循环伏安法对HQ电化学行为进行研究,结果表明,HQ在3.0×10-8~1.0×10-6mol/L和1.0×10-6~1.0×10-4mol/L浓度范围内与峰电流呈良好的线性关系,据此建立了检测HQ的电化学分析方法。该方法的相对标准偏差为0.69%,检出限(S/N=3)为1.0×10-8mol/L,具有较高的稳定性和灵敏度。     

Determination of Oxytetracycline with a Gold Electrode Modified by Chitosan-Multiwalled Carbon Nanotube Multilayer Films and Gold Nanoparticles

A molecularly imprinted electrochemical sensor was fabricated based on a gold electrode modified by chitosan-multiwalled carbon nanotube composite (CS-MWCNTs) multilayer films and gold nanoparticles (AuNPs) for convenient and sensitive determination of oxytetracycline (OTC). The multilayer of CS-MWCNTs composites and AuNPs were used to augment electronic transmission and sensitivity. The molecularly imprinted polymers (MIPs) were synthesized using OTC as the template molecule and o-phenylenediamine (OPD) as the functional monomer. They were modified on a gold electrode by electropolymerization. The electrochemical behavior of OTC at the imprinted sensor was characterized by cyclic voltammetry (CV), scanning electron microscopy (SEM), and amperometry. The molecularly imprinted sensor showed high selectivity and excellent stability toward OTC. The linear range was from 3.0 × 10^?8 to 8.0 × 10^?5 mol/L, with a limit of detection (LOD) of 2.7 × 10^?8 mol/L (S/N = 3). The developed sensor showed good recovery in spiked samples analysis.     

Electrocatalytic Determination of Traces of Hydrazine by a Glassy Carbon Electrode Modified with Palladium‐Gold Nanoparticles

A glassy carbon electrode modified with palladium/gold nanoparticles was successfully prepared by an electrodeposition process. It efficiently oxidizes hydrazine at a low overpotential of ?0.26 V versus SCE. The Pd‐AuNPs with an average size of 50–80 nm are uniformly dispersed at the GCE. The Pd‐AuNPs/GCE was used for determination of hydrazine in phosphate buffer solution of pH 7.0. The amperometric current response of the electrode was increased linearly over a hydrazine concentration of 0.1–500 µM with a limit of detection of 0.07 µM .The prepared hydrazine sensor exhibited high sensitivity, good selectivity reproducibility and long term stability.     

Electrochemical Determination of Tetracycline Using Molecularly Imprinted Polymer Modified Carbon Nanotube‐Gold Nanoparticles Electrode

This paper reports the use of a tetracycline (TC) sensor constructed from a combination of molecularly imprinted polymer (MIP) and gold nanoparticles modified multiwall carbon nanotubes (MWNTs‐GNPs). The results demonstrated that the amount of recognition sites in the polymer was significantly increased and the electron transfer ability of the sensor was improved. The relationship between the peak current and the TC concentration was linear in the range from 0.1 to 40 mg L^?1, and the detection limit was 0.04 mg L^?1 (S/N=3). The peak current to TC was 4.3, 6.2 and 6.8 times larger than that of oxytetracycline, chloramphenicol and nafcillin, respectively. Thus, the combination of MIP and MWNTs‐GNPs provides a sensitive and selective electrochemical detection method for tetracycline.