Molecular orientation of aromatic polycarbonates containing fluorene side chains by polarized infrared spectroscopy and birefringence analysis

The molecular orientation of an aromatic polycarbonate containing fluorene side chains was investigated by polarized infrared spectroscopy and birefringence analyses. The copolymers were synthesized from 2,2‐bis(4‐hydroxyphenyl)propane (BPA), 9,9‐bis(4‐hydroxy‐3‐methylpheny)fluorene (BMPF), and phosgene by interfacial polycondensation. The 1449‐cm^?1 band of the uniaxially oriented films, stretched at the glass‐transition temperature (T_g) plus 5 °C, was assigned to various combinations of CC stretching and CH in‐plane bending vibrations in the fluorene ring, and the transition moment angle was estimated to be 90°. The intrinsic birefringence of aromatic polycarbonate films with BMPF molar ratios ranging from 0.5 to 1 was obtained with the 1449‐cm^?1 band. The copolymer was estimated to show zero intrinsic birefringence at the BMPF molar ratio of 0.75, and the BMPF homopolymer showed negative intrinsic birefringence. A linear relationship between the volume fraction of BMPF units and the intrinsic birefringence indicated that the two monomer units of BPA and BMPF in each copolymer were not independent, and an intrinsic birefringence could be defined even in the copolymer. The sign of the photoelastic coefficient in the homopolymer with BMPF units was positive. The different signs of the photoelastic coefficient and the intrinsic birefringence suggest that the fluorene side‐chain orientation induced by stress in the glass state is quite different from the orientation of the uniaxially oriented films stretched at T_g + 5 °C. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1554–1562, 2003     

Molecular composites prepared by in situ direct synthesis of wholly aromatic rigid‐rod polyamides via the phosphorylation reaction in a dissolved nylon‐6 matrix

Wholly aromatic rigid‐rod polyamides such as poly(p‐phenyleneterephthalamide) (PPD‐T) were synthesized in situ in a solution of nylon‐6 via the phosphorylation polycondensation method to form nanocomposites or so‐called “molecular composites.” The incorporation of PPD‐T into a nylon‐6 matrix was achieved by this approach in a more compatibilized form than that obtained by the conventional coagulation method that entails precipitation of a blend of PPD‐T and nylon‐6 in a solvent, for example, concentrated sulfuric acid. Gelation occurred during the synthesis, presumably because of the formation of interpenetrating networks accompanied by some block‐copolymer formation. The transparency and tensile properties of the resultant composite films from the rigid‐rod aromatic polyamide/nylon‐6 combination were improved over those of nylon‐6 film alone. Rainbow‐colored intense birefringence was observed for the composite films under crossed polarizers. These properties are discussed in context with the in situ synthesized rigid‐rod polyamides uniformly incorporated in nylon‐6. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1014–1026, 2003     

Correlation between the tensile properties and network draw ratio of CO2‐laser‐heated drawn poly(ethylene terephthalate) fibers

Low‐orientation and amorphous poly(ethylene terephthalate) fibers were drawn continuously with heating by carbon dioxide (CO₂) laser radiation. The tensile properties were examined in terms of the birefringence and network draw ratio, which was estimated from the strain shift of true stress–strain curves. Two drawing forms, neck drawing with a draw efficiency (the ratio of the network draw ratio to the actual draw ratio) of about unity and flow drawing with a draw efficiency of about zero, were found to be stable in the continuous drawing process. Meanwhile, any draw‐efficiency value between zero and unity could be obtained in the batch‐drawing process. The object whose orientation was estimated by the network draw ratio differed from that estimated by birefringence. Two linear relationships were found, between the network draw ratio and tensile strength and between the birefringence and initial modulus. The true stress at breaking increased with the network draw ratio of the CO₂‐laser‐heated drawn fibers, and when the draw ratio exceeded 5.0, it became higher than that for batch‐drawn fibers. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2322–2331, 2003     

Birefringence study of drawn Nafion films

Nafion films are birefringent. This optical property has been studied as a function of the draw ratio to obtain insight into the film morphology. At small draw ratios, the structure shows biaxial behavior. At higher draw ratios (>150%), Nafion can be considered to have a uniaxial symmetry. The influence on the birefringence of three different counterions (hydrogen, lithium, and tetramethylammonium) is negligible. Undrawn Nafion shows preorientation, which can be eliminated with drawing in the proper direction. X‐ray experiments suggest that the physical origin of the birefringence in Nafion is mainly due to the orientation of the polymer chains and not due to deformation or form birefringence. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2857–2870, 2004     

Synthesis and characterization of thermally stable,high‐modulus polyimides containing benzimidazole moieties

A series of novel benzimidazole‐containing aromatic polyimides were prepared from synthesized 5,4′‐diamino‐2‐phenyl benzimidazole (DAPBI), and commercial dianhydrides by the conventional two‐step polymerization. The obtained films were amorphous and could afford flexible, transparent, and tough films with excellent thermal and mechanical properties. They showed high levels of tension strength of up to 234 MPa, modulus of up to 5.6 GPa without any stretching. According to thermal stability measurements, the glass‐transition temperatures of the polymers were observed between 329 and 425 °C. The 5% weight‐loss temperatures of most polyimides were above 600 °C in nitrogen. Excellent properties of these polyimides were proved to be attributed to the rigid‐rod structure and hydrogen bond of intermacromolecular. SAXS and SEM results showed self‐molecular orientation caused the formation of rod‐like extended conformations. It was demonstrated that high degree of supramolecular order led to the increase of thermal stability and mechanical properties of the polyimide films. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2024–2031, 2009     

Role of the in‐plane orientation of polyimide films in graphitization

Poly(amide acid) labeled with perylenetetracarboxydiimide (PEDI) was prepared from 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA), p‐phenylenediamine (PDA), and diamino‐PEDI. Poly(amide acid) was then reacted with sodium hydride and various kinds of alkyl iodides for transformation into various poly(amide ester)s. The cast films were imidized while fixed on glass substrates to give BPDA/PDA polyimide films. The degree of in‐plane molecular orientation (f) of the polyimides and their precursors, poly(amide acid) and poly(amide ester)s, were determined via measurements of the visible dichroic absorption at an incidence angle for a rodlike dye (PEDI) bound to the main chain. All precursor films showed relatively low degrees of in‐plane orientation. After imidization of the precursors fixed on glasses, however, striking spontaneous in‐plane orientation behavior was observed. The f value for polyimide film from a poly(amide acid) precursor was as high as 0.7–0.8. The f value for polyimide film from a methyl ester precursor, however, was lowered to 0.4–0.5, but it increased with the increasing size of the alkyl groups. Good correlations of the in‐plane orientation of the polyimide films with the tensile modulus of the films and the in‐plane orientation of the graphitized films were observed. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 3011–3019, 2001     

Nanoindentation studies of polyimide thin films with various internal linkages in the diamine component

Polyimide thin films were synthesized from 3,3′,4,4′‐biphenyltetracarboxylic acid dianhydride (BPDA) and four different diamines (p‐phenylene diamine, 4,4′‐oxydiphenylene diamine, 4,4′‐biphenylene diamine, and 4,4′‐sulfonyldiphenylene diamine). The nanoindentation behavior of the resulting polyimides, namely, poly(p‐phenylene biphenyltetracarboximide) (BPDA‐PDA), poly(4,4′‐biphenylene biphenyltetracarboximide) (BPDA‐BZ), poly(4,4′‐oxydiphenylene biphenyltetracarboximide) (BPDA‐ODA), and poly(4,4′‐sulfonyldiphenylene biphenyltetracarboximide) (BPDA‐DDS), were investigated. Also, the morphological properties were characterized with a prism coupler and wide‐angle X‐ray diffraction and were correlated to the nanoindentation studies. The nanoindentation behavior and hardness varied quite significantly, depending on the changes in the chemical and morphological structures. The hardness of the polyimide thin films increased in the following order: BPDA‐DDS < BPDA‐ODA < BPDA‐BZ < BPDA‐PDA. For all the polyimide thin films, except that of BPDA‐BZ, the hardness decreased with an increase in the load. The birefringence, a measure of the molecular in‐plane orientation, increased in the following order: BPDA‐DDS < BPDA‐ODA < BPDA‐PDA < BPDA‐BZ. The X‐ray diffraction studies revealed that the crystallinity of the polyimide thin films varied with the changes in the chemical structure. The studies showed that the indentation response with an applied load and the hardness by nanoindentation for the BPDA‐based polyimides were closely related to the morphological structure. The nanoindentation and birefringence results revealed that the mechanical properties of the polyimide thin films were dependent on the crystallinity, which arose because of the chain order along the chain axis and the molecular packing order. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 861–870, 2004     

Structure–electrical property study of anisotropic polyaniline films

The relationships of the structure and electrical properties of anisotropic HCl‐doped polyaniline (PANI) films cast from N,N′‐dimethylpropylene urea (DMPU) solutions and stretched to different draw ratios were studied. The anisotropic structure of the stretched PANI films was examined by X‐ray diffraction, near‐infrared wave‐guide coupling, and polarized infrared measurements. The PANI emeraldine base (EB) films cast from DMPU solutions had a single‐phase noncrystalline structure, and stretching of the films did not cause crystallization to occur. The transition moment angles of two weakly absorbing infrared bands were determined, and the Hermans' orientation functions for the PANI EB films were calculated. The PANI films were then doped with HCl, and the electrical properties were determined by impedance spectroscopy. With a specially designed test fixture, the in‐plane and through‐plane impedance was obtained. The conductivity along the stretch direction increased with orientation. The in‐plane conductivity was significantly higher than the through‐plane conductivity. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 823–841, 2003     

A rod‐like fluorinated polyimide as an in‐plane birefringent optical material 2: Control of optical retardation using spontaneous molecular orientation

Following previous work, a fluorinated polyimide with a rod‐like structure has been investigated as an in‐plane birefringent optical material whose birefringence and thickness can be precisely controlled. Poly(amic acid) films fixed in a metal frame by two sides and thermally cured without any drawing resulted in a polyimide film with an in‐plane birefringence (Δn) larger than 0.1 at 1543 nm. The optical retardation, which is defined as the product of Δn and the film thickness, was controlled by varying the curing and post‐annealing temperatures and by using reactive ion etching. In situ measurements of the tensile stress and the generated retardation showed that the initial orientation at below 200°C was due to the large tensile stress caused by the film shrinkage during imidization and that the increased Δn at higher temperatures was caused by the spontaneous orientation of the polyimide molecules. The curing temperature dependence of refractive indices, optical transmittance in the visible and near‐infrared region, and the wavelength dispersion of retardation of the in‐plane birefringent polyimide films are also reported. Copyright © 1999 John Wiley & Sons, Ltd.     

Water sorption and activation energy in polyimide thin films

The water sorption behavior and the activation energy were investigated for various chemical structure polyimide thin films; BPDA‐PDA, BPDA‐ODA, PMDA‐ODA, and 6FDA‐ODA. The activation energy for the water diffusion varied in the range of 5.53 to 9.27kcal/mol, and was in the increasing order: BPDA‐PDA < BPDA‐ODA < PMDA‐ODA < 6FDA‐ODA. BPDA‐PDA and BPDA‐ODA polyimide films showed relatively well‐ordered morphological structure, which results in relatively low diffusion coefficient and high activation energy. It was found that the diffusion coefficient and the activation energy are significantly related to the in‐plane orientation, crystallinity, and packing order in the polyimide thin films. The morphological structure was predominant factors for the water diffusion coefficient and activation energy in the polyimide thin films. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2714–2720, 2000     

Structural anisotropy in unstretched and uniaxially stretched poly(p‐phenylene vinylene)

Poly(p‐phenylene vinylene) or PPV is gaining increasing importance because of its superior electroluminescent efficiency and electrical conductivity. The most widely followed synthetic route for PPV involves synthesis of a precursor polymer using a sulfonium monomer salt. Previous studies have proven that the monomer salt which contains cyclic sulfonium groups yields better quality PPV than when the monomer containing dialkyl sulfonium groups is used. The structure of PPV synthesized using cyclic sulfonium precursor has not been as widely reported as that synthesized using dialkyl sulfonium monomer. In the current work, the structure of PPV, synthesized using a cyclic viz. tetrahydrothiophenium monomer salt, has been studied in detail using the wide angle X‐ray diffraction (WAXD) technique. The study reveals that even in the cast (unstretched) form, PPV shows considerable biaxial orientation in the plane of the film. This preferred orientation is found to occur during the casting process and is independent of the solvent used and casting substrate. On stretching these films to a final draw ratio of 7 : 1, this biaxial orientation is transformed into uniaxial orientation with nematic ordering of PPV chains along the stretch direction and PPV chains assuming three preferred orientations in the plane of the film. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 605–614, 1999     

In‐plane birefringence and elongation behavior of uniaxially drawn aromatic polyimide films

Six kinds of aromatic poly(amic acid) films, the precursor of polyimides, were uniaxially drawn by constant loads during thermal curing with varying the final curing temperature and the load. The in‐plane birefringence (Δn) generated by uniaxial orientation of polyimide molecules in the film plane was investigated in relation with their molecular structures and the elongation behavior of polyimide films. The polyimides derived from pyromellitic dianhydride (PMDA) showed much larger values of Δn than the polyimides derived from dianhydrides having rotatable diphenyl linkages. The Δn of the former polyimides increases with increasing the final curing temperature and the elongation between the most shrunken and the most elongated states during curing. In particular, the polyimides having rod‐like structures show the largest value of Δn. In contrast, the latter polyimides take maximal values of Δn at much lower temperatures. The introduction of hexafluroisopropiridene (? C(CF₃)₂? ) group into the main chain effectively lowers the values of Δn. This result can be related to the inherent low polarizability anisotropy and the decreased molecular packing constant that are characteristic of highly fluorinated groups. These experimental results are qualitatively explained by the calculations of polarizability anisotropies of model compounds using FPT‐MNDO‐PM3 theory. Copyright © 2001 John Wiley & Sons, Ltd.     

Effect of molecular orientation on the fracture behavior of carbon black-filled natural rubber compounds

The fracture behavior of carbon black-filled natural rubber compounds, differing in filler content, was studied performing tensile tests in biaxial loading conditions, using a central notched cross-shaped specimen. The test consisted of two steps: a drawing step was initially performed loading the specimen in the direction parallel to the notch plane, up to different draw ratios, and then the specimen was loaded in the direction normal to the notch plane up to fracture. Using a fracture mechanics approach, the fracture toughness was evaluated as a function of the draw ratio applied in the drawing step. A correlation between the fracture phenomenology observed and molecular orientability and orientation was attempted. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1509–1515, 2010     

Quantitative analysis of near surfaces three‐dimensional orientation of polymer chains in PET and PEN films using polarized ATR FTIR spectroscopy

Polarized attenuated total reflection (ATR) Fourier transform infrared (FTIR) spectroscopy was utilized to characterize the three‐dimensional orientation of polymer chains near highly anisotropic surfaces generated by uniaxial drawing. A versatile method was proposed to analyze the molecular orientation of the polymers by combining the experimental refractive indices and optimized contact pressure by an anvil for solving the optical contact problem. This method is effective even when changes in the molecular orientation along the thickness direction caused by drawing are remarkable. In addition, this method enables quantitative comparison of the molecular orientation among different polymers in the same coordinate system. From the molecular orientation analysis of poly (ethylene terephthalate) (PET) and poly (ethylene naphthalate) (PEN), it was revealed that this method has a broader range of applications with high accuracy in estimating the molecular orientation of polymers compared with the conventional methods. The significant changes in the molecular orientation caused by uniaxial and biaxial drawing of PET and PEN films were quantitatively analyzed, and the reasons for the significant in‐plane orientation of PEN chains on the film plane are discussed. In addition, the difference in the molecular orientation between both sides of the films was also demonstrated. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 870–879, 2010     

Melt spinning and laser‐heated drawing of a new semiaromatic polyamide,PA9‐T fiber

Fibers of PA9‐T, a new semiaromatic polyamide containing a long aliphatic chain, were prepared by melt spinning. As‐spun fibers were subsequently drawn with a CO₂ laser‐heated drawing system at different draw ratios and various drawing velocities. On‐line observations of drawing points deciphered two drawing states; namely, flow drawing and neck drawing, over the entire range of drawing. Drawing stress revealed that flow drawing is induced by slight drawing stress under a low draw ratio up to 3, and neck drawing is induced by relatively high drawing stress under a higher draw ratio. The effect of drawing stress and drawing velocity on the development of the structure and properties has been characterized through analysis of birefringence, density, WAXD patterns, and tensile, thermal, and dynamic viscoelastic properties. For the neck‐drawn fibers, almost proportional enhancements of crystallinity and molecular orientation with drawing stress were observed. The flow‐drawn fibers have an essentially amorphous structure, and birefringence and density do not always have a linear relation with properties. The fibers drawn at high drawing speed exhibit improved fiber structure and superior mechanical properties. The maximum tensile strength and Young's modulus of PA9‐T drawn fibers were found to be 652 MPa and 5.3 GPa, respectively. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 433–444, 2004     

Real‐time orientation and crystallinity measurements during the isotactic polypropylene film‐casting process

A method based on Fourier transform infrared (FTIR) transmission spectra is proposed to measure the crystallinity of isotactic polypropylene (iPP) samples. The method parameters were tuned as compared with wide‐angle X‐ray scattering measurements performed on test samples characterized by different crystallinity values obtained by solidification of thin iPP films under several cooling rates in a homemade device. The FTIR dichroic ratio measurements were adopted to measure crystalline and average Hermans' orientation factors of iPP samples obtained by film casting. The crystalline orientation measurement method was validated as compared with the birefringence measurement. The techniques were successfully used in real time during some film‐casting runs with a suitably modified FTIR system made of a spectrometer equipped with two optical guidelines and an external detector. Real‐time measurements are reported and discussed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 998–1008, 2003     

Modeling the mechanical properties of highly oriented polymer films: A fiber/gel composite theory approach

Controlling the extent of orientation is of great interest in polymer processing and is effected by the choice of polymer, the fabrication technique and the processing conditions. Understanding the crystalline transitions that form highly oriented fibrils is necessary for modeling the changes in physical properties, relative to degree of orientation. A model is proposed to describe the mechanical properties of drawn semicrystalline polymer films based on structural transitions. With a minimal amount of experimental data (requiring testing on only two drawn films samples), this model can be used to predict film properties. These properties include the critical and maximum draw ratios, the moduli at the maximum draw ratio, the moduli of the fiber, the modulus of the nonfibrous gel relative to draw ratio, the volume fraction of fibers, and the rate of fibrillation. Where high degrees of uniaxial orientation are required, the polymer is typically drawn in the solid state, meaning the polymer is stretched in a single direction at temperatures below the melting point. During this process, pre‐existing crystallites are transformed into fiber‐like structures with large aspect ratios. The presence of these rigid asymmetric structures significantly enhances the moduli and break strength of the polymer. This work presents a model that describes the formation of fiber‐like structures. The volume fraction of fibers is predicted to be linear in draw ratio. The derived relationship between volume fraction of fibers and draw ratio can then be used for the prediction of the various properties of the oriented film. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 607–618, 2008     

Photoinduced alignment of azobenzene side‐chain polymers with short spacer: Biaxial orientation and fast response

Side‐chain azobenzene‐containing liquid crystalline polymer (ALCP) of Poly(6‐[4‐(4‐cyanophenylazo)phenoxy] x‐methylene methacrylate)(Px, x is 2 or 6) was synthesized and used to study its photoinduced alignment behavior irradiated by a linearly polarized laser at room temperature. The relationships between transmittance and irradiation time as well as transmittance and various incident angles were studied in detail. The oversaturation phenomenon of P ₂ film was found to be higher than 1 mW/cm² under irradiation energy density. A model of the biaxial orientation was introduced to explain the phenomenon: it is the rigid short spacer that makes it possible for mesogen to coexist in a way of out‐of‐plane and in‐plane orientation (biaxial orientation), in which the type of photoinduced motions is a single mesogen motion in the film of P ₂ , whereas in the film of P ₆ with longer spacer, the motion is a microdomain motion. The whole domain motion restricted the out‐of‐plane orientation, which shows a slow orientation rate and all mesogens aligned within the film plane. A novel dynamic fitting was also presented to describe the orientation of P ₂ , which was discussed in terms of the fitting parameters. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1378–1384, 2006     

Anisotropy in the thermal shrinkage of polyimide film

Anisotropy in a polyimide film was investigated in a quantitative manner by a nonlinear regression of the thermal shrinkage data obtained from thermomechanical analysis. The thermally induced shrinkage of this pyromellitic dianhydride–oxydianiline polyimide film at 573 K was directionally anisotropic in the film plane by as much as about 0.4%. The direction of maximum thermal shrinkage was inclined by about π/6 rad from the machine direction of the film. The thermal shrinkage behavior of the polyimide films in the vicinity of the glass‐transition temperature (T_g) showed an unusual anisotropic response. On the basis of a correlation between the anisotropy in the thermal shrinkage of the films and the molecular orientation of the polyimide, this characteristic thermal shrinkage behavior around T_g is suggested to be due to a recovery of the free volume lost by a physical aging process. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 3222–3229, 2000     

Molecular structure and thickness dependence of chain orientation in aromatic polyimide films

Degrees of orientation of main chains and imide rings were quantitatively estimated for spin‐coated films of six kinds of aromatic polyimides (PIs) using polarized attenuated total reflection (ATR)/Fourier transform infrared (FT‐IR) spectroscopy. The degrees of chain orientation parallel to the film planes are significantly larger for the PIs having rigid structures than those having flexible structures, and the introduction of side groups decrease the degrees of chain orientation. In contrast, the rotational orientations of imide rings are almost isotropic for all PI films. Moreover, the film thickness dependences of the degrees of orientation were investigated for two kinds of rigid‐rod PIs having bulky trifluoromethyl ( CF₃) side groups in their diamine moieties. The degrees of chain orientation slightly decrease as the film thickness increases, whereas the rotational orientation of imide rings is independent of the film thickness. The degrees of chain orientation on the substrate sides significantly differ from the atmospheric sides of PI films. This difference was generated during thermal imidization because of tensile stress originated from the mismatch in thermal expansion coefficients between the substrates and the PI films. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2109–2120, 2005