Microstructure and mechanical properties of hot‐air drawn poly(ethylene terephthalate) fibers

Hot‐air drawing method has been applied to poly(ethylene terephthalate) (PET) fibers in order to investigate the effect of strain rate on their microstructure and mechanical properties and produce high‐performance PET fibers. The hot‐air drawing was carried out by blowing hot air controlled at a constant temperature against an as‐spun PET fiber connected to a weight. As the hot air blew against the fibers weighted variously at a flow rate of about 90 ℓ/min, the fibers elongated instantaneously at a strain rate in the range of 2.3–18.7 s⁻¹. The strain rate in the hot‐air drawing increased with increasing drawing temperature and applied tension. When the hot‐air drawing was carried out at a drawing temperature of 220°C under an applied tension of 27.6 MPa, the strain rate was the highest value of 18.7 s⁻¹. A draw ratio, birefringence, crystallite orientation factor, and mechanical properties increased as the strain rate increased. The fiber drawn at the highest stain rate had a birefringence of 0.231, degree of crystallinity of 44%, tensile modulus of 18 GPa, and dynamic storage modulus of 19 GPa at 25°C. The mechanical properties of fiber obtained had almost the same values as those of the zone‐annealed PET fiber reported previously. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1703–1713, 1999     

Microstructure and protonic conductivity of H3PO4‐doped polyethylenimine–siloxane chemically covalently organic–inorganic hybrids

The chemically covalent polyethylenimine–siloxane hybrids doped with various amounts of ortho‐phosphoric acid (H₃PO₄) were prepared and characterized by FTIR, DSC, TGA, and solid‐state NMR spectra. The protonic conduction behavior of these materials was also investigated by means of impedance measurements. These observations indicate that the hydrogen bonding and protonic interactions exist between the dopant H₃PO₄ and the hybrid host, resulting in an increase in T _g of polyethylenimine segments. These hybrids are thermally stable up to 200 °C from TGA analysis. Conductivity studies show an Arrhenius behavior characteristic and the Grotthus‐like proton conduction, and a high conductivity of 10^?2–10^?3 S cm^?1 at 110 °C in dry atmosphere for the hybrid membrane with H₃PO₄/EI of 0.5. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2135–2144, 2006     

Strain‐rate dependence of the microstructure and mechanical properties for hot‐air‐drawn nylon 6 fibers

A hot‐air (HA) drawing method was applied to nylon 6 fibers to improve their mechanical properties and to study the effect of the strain rate in the HA drawing on their mechanical properties and microstructure. The HA drawing was carried out by the HA, controlled at a constant temperature, being blown against an original nylon 6 fiber connected to a weight. As the HA blew against the fiber at a flow rate of 90 liter/min, the fiber elongated instantaneously at strain rates ranging from 9.1 to 17.4 s⁻¹. The strain rate in the HA drawing increased with increasing drawing temperature and applied tension. When the HA drawing was carried out at a drawing temperature of 240 °C under an applied tension of 34.6 MPa, the strain rate was at its highest value, 17.4 s⁻¹. The draw ratio, birefringence, crystallite orientation factor, and mechanical properties increased as the strain rate increased. The fiber drawn at the highest strain rate had a birefringence of 0.063, a degree of crystallinity of 47%, and a dynamic storage modulus of 20 GPa at 25 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1137–1145, 2000     

Effect of strain‐induced molecular ordering on mechanical performance and barrier properties of polylactide nanocomposites

Plastic deformation of polylactide has been known as a self‐reinforcement alternative to improve mechanical and barrier properties. In this study, the structural evolution was investigated during a hot‐drawing process, at different initial strain rates and temperatures above T_g of polylactide. The drawing process at T_g +10 °C, led to the formation of an intermediate molecular ordering, between the crystalline and amorphous phases. A lower fraction of this mesomorphic phase was found to develop with the addition of nanoparticles. An increase in the stretching temperature to T_g +30 °C, caused an improvement of the crystallization kinetics, compared to that of thermally activated crystallization. A strain hardening behavior was observed in the presence of mesophase during a stretching process of the hot‐drawn films at room temperature. Permeability was discerned to its basic components, diffusivity, and solubility coefficients. The matrix degradation influenced the permeability components. The diffusivity decreases in the presence of the impermeable matters. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1865–1876     

Orientation of uniaxially stretched poly(ethylene naphthalene 2,6‐dicarboxylate) films by polarized infrared spectroscopy

Poly(ethylene naphthalene‐2,6‐dicarboxylate) has been uniaxially stretched at different draw ratios and at two different temperatures below and above its glass transition (T_g ～ 120 °C) respectively, at 100 and 160 °C. Crystallinity has been evaluated from calorimetric analyses and compared to the values deduced by FTIR spectroscopic data. As expected, the obtained results are quite similar and show that films stretched at lower temperature (100 °C) are more crystalline than those stretched at 160 °C. Optical anisotropy associated with orientation has been evaluated by birefringence and show that films stretched at 100 °C are more birefringent than those stretched at 160 °C as a result of a higher chain relaxation above T_g. Polarized FTIR was also performed to evaluate the individual orientation of amorphous and crystalline phases by calculating dichroic ratios R and orientation functions 〈P₂(cos θ)〉 and also show that amorphous and crystalline phases are more oriented in the case of films stretched below T_g. Nevertheless, the orientation of the amorphous phase is always weaker than that of the crystalline phase. Films stretched at 100 °C show a rapid increase in orientation (and crystallinity) with draw ratio and 〈P₂(cos θ)〉 reaches a limit value when draw ratio becomes higher than 3.5. Films drawn at 160 °C are less oriented and their orientation is increasing progressively with draw ratio without showing a plateau. A careful measurement of the IR absorbance was necessary to evaluate the structural angles of the transition moments to the molecular chain axis. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1950–1958, 2007     

Surface‐initiated ring‐opening polymerization of p‐dioxanone on Wang resin bead

Biodegradable poly(p‐dioxanone) (PPDO) was formed on Wang resin surface by surface‐initiated ring‐opening polymerization (SI‐ROP). The SI‐ROP of p‐dioxanone (PDO) was achieved by heating a mixture of Tin(II) bis(2‐ethylhexanoate) [Sn(Oct)₂], hydroxyl functionalized Wang resin, and PDO in anhydrous toluene at 80 °C. The resultant polymer‐grafted Wang resin (Wang‐g‐PPDO) was characterized by fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), optical microscopy (OM), and field‐emission scanning electron microscopy (FE‐SEM). The FTIR spectra of Wang‐g‐PPDO show peak characteristic of PPDO at 2943 cm^?1 (? C? H stretch), at 1741 cm^?1 (? C?O stretch), and 1136 cm^?1 (C? O? C stretch) indicating the formation of ester linkage between PPDO and hydroxyl terminated Wang resin. The DSC thermogram show melting peak corresponding to PPDO polymer on Wang resin surface. Thermogravimetric investigation shows increase in PPDO content on the Wang resin surface in terms of percentage of weight loss with increase in reaction time. The OM and SEM photographs clearly show the formation of PPDO polymer on the Wang resin surface without altering the spherical nature of Wang resin bead. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1178–1184, 2008     

Temperature dependence of the activation volume in a nonlinear optical polymer: Evidence for chromophore reorientation induced by sub-Tg relaxations

Second harmonic generation (SHG) was used to measure the temperature dependence of the reorientation activation volume of 4-(diethylamino)-4′-nitrotolane (DEANT) in poly(methyl methacrylate) (PMMA). The decay of the SHG signal from films of DEANT/PMMA was recorded at hydrostatic pressures up to 3060 atm and at different temperatures between 25°C below the glass transition temperature to 35°C above it. The activation volume, ΔV*_αβ associated with the long range α-type motion of the polymer remained constant at 213 ± 10 ų between T_g − 25°C and T_g + 10°C. At higher temperatures, ΔV*_αβ decreased linearly with increasing temperature. The activation volume, ΔV*_αβ, associated with short range secondary relaxations was constant over the entire temperature range with a value of 77 ± 10 ų. The data suggest that above T_g chromophore reorientation is coupled to both the long range and local motions of the polymer; whereas, well below T_g chromophore reorientation is closely coupled to the local relaxations of the polymer. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 901–911, 1998     

Linear diacetylene polymers containing bis(dimethylsilyl) phenyl and/or bis-(tetramethyldisiloxane) carborane residues: Their synthesis,characterization and thermal and oxidative properties

A series of inorganic-organic linear diacetylenic hybrid polymers ( 5a–e ) were prepared by the polycondensation reaction of 1,4-dilithiobutadiyne with 1,4-bis(dimethylchlorosilyl)benzene and/or 1,7-bis(tetramethylchlorodisiloxane)-m-carborane. Their structures were characterized using FTIR, and ¹³C and ¹H NMR spectroscopies, and their thermal and oxidative properties were evaluated by DSC and TGA analyses. The hybrid polymers exhibited solubility in common organic solvents and were viscous liquids or low melting solids at room temperature. Broad prominent exotherms, attributed to reaction of the diacetylenic units, were observed by DSC in the 306°C to 354°C temperature range. When 5a–e were analyzed by TGA to 1000°C under nitrogen, weight retention between 79 and 86% were obtained. Ageing studies, performed at elevated temperatures in air on a thermoset and a ceramic obtained from polymer 5b , showed this system to have excellent thermal and oxidative stability. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2387–2391, 1997     

Metathesis polymerization of N-aryl norbornene dicarboximides. I

Metathesis polymerization of N-phenyl-exo-norbornene dicarboximide and ortho/meta/para methyl substituted phenyl nadimides was carried out using WCl₆/tetramethyltin. Structural characterization was done by FTIR, ¹H- and ¹³C-NMR. A mixture of cis and trans double bond structures were introduced in the backbone during polymerization. The cis content was higher (52 to 65%). In the DSC scan of poly(N-o-tolyl nadimide), two exotherms were observed at 240 and 270°C while in other samples only one exothermic transition was observed above 240°C. These exotherms disappeared in the second heating cycle. The T_g of the polymers, as determined in the second heating cycle, was highest in poly(N-o-tolyl nadimide) and lowest in poly(N-m-tolyl nadimide). The polymers were stable up to 443 ± 3°C and decomposed above this temperature in a single step. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2917–2924, 1997     

Synthesis and characterization of polyesteramides derived from an oxazoline-functional alcohol and dicarboxylic acid anhydrides

Novel polyesteramides were synthesized by copolymerization in bulk of 5-(4,5-dihydro-1,3-oxazol-2-yl)-1-pentanol and various cyclic dicarboxylic acid anhydrides at temperatures varying between 120 and 200°C. The polymers resulting from polycondensation were characterized by means of ¹H–NMR, FTIR, MALDI–TOF–MS, SEC, and DSC. The glass transition temperatures, T_g, of the copolymers were varied between −28 and +31°C as a function of the anhydride type. Molecular weights, M_w, were dependent on reaction temperature, reaction time, and anhydride type. Spectroscopic investigation of reaction products and esteramide model compounds provided evidence for imide by-product formation, which accounts for the low degree of polymerization. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3367–3376, 1999     

Synthesis and characterization of poly(3,3 bis(azidomethyl)oxetane‐co‐ε‐caprolactone)s

The quasi‐living cationic copolymerization of 3,3‐bis(chloromethyl)oxetane (BCMO) and ε‐caprolactone (ε‐CL), using boron trifluoride etherate as catalyst and 1,4‐butanediol as coinitiator, was investigated in methylene chloride at 0°C. The resulting hydroxyl‐ended copolymers exhibit a narrow molecular weight polydispersity and a functionality of about 2. The reactivity ratios of BCMO (0.26) and ε‐CL (0.47), and the T_g of the copolymers, indicate their statistical character. The synthesis of poly(3,3‐bis(azidomethyl)oxetane‐co‐ε‐caprolactone) from poly(BCMO‐co‐ε‐CL) via the substitution of the chlorine atoms by azide groups, using sodium azide in DMSO at 110°C, occurs without any degradation, but the copolymers decompose at about 240°C. All polymers were characterized by vapor pressure osmometry or steric exclusion chromatography, ¹H‐NMR and FTIR spectroscopies, and DSC. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1027–1039, 1999     

Rigid‐rod polyamides and polyimides prepared from 4,3″‐diamino‐2′,6′‐di(2‐naphthyl)‐p‐terphenyl and 2′,6′,3‴,5‴‐tetra(2‐naphthyl)‐4,4″‐diamino‐p‐quinquephenyl

A series of rigid‐rod polyamides and polyimides containing p‐terphenyl or p‐quinquephenyl moieties in backbone as well as naphthyl pendent groups were synthesized from two new aromatic diamines. The polymers were characterized by inherent viscosity, elemental analysis, FT‐IR, ¹H‐NMR, ¹³C‐NMR, X‐ray, differential scanning calorimetry (DSC), thermomechanical analysis (TMA), thermal gravimetric analysis (TGA), isothermal gravimetric analysis, and moisture absorption. All polymers were amorphous and displayed T_g values at 304–337°C. Polyamides dissolved upon heating in polar aprotic solvents containing LiCl as well as CCl₃COOH, whereas polyimides were partially soluble in these solvents. No weight loss was observed up to 377–422°C in N₂ and 355–397°C in air. The anaerobic char yields were 57–69% at 800°C. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 15–24, 1999     

Application of zone-drawing and zone-annealing method to poly(p-phenylene sulfide) fibers

A zone-drawing and zone-annealing treatment was applied to poly(p-phenylene sulfide) fibers in order to improve their mechanical properties. The zone-drawing (ZD) was carried out at a drawing temperature of 90°C under an applied tension of 5.5 MPa, and the zone-annealing (ZA) was carried out at an annealing temperature of 220°C under 138.0 MPa. The differential scanning calorimetry (DSC) thermogram of the ZD fiber had a broad exothermic transition (T_c = 110°C) attributed to cold-crystallization and a melting endotherm peaking at 286°C. The T_c of the ZD fiber was lower than that (T_c = 128°C) of the undrawn fiber. In the temperature dependence of storage modulus (E′) for the ZD fiber, the E′ values decreased with increasing temperature, but increased slightly in the temperature range of 90–100°C, and decreased again. The slight increase in E′ was attributable to the additional increase in the crosslink density of the network, which was caused by strain-induced crystallization during measurement. The resulting ZA fiber had a draw ratio of 6.0, a degree of crystallinity of 38%, a tensile modulus of 8 GPa, and a tensile strength of 0.7 GPa. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1731–1738, 1998     

Synthesis and characterization of new poly(amide–imide)s from 1,4-bis(4-trimellitimidophenoxy)-2-tert-butylbenzene with various diamines

New poly(amide–imide)s were prepared from a diimide–dicarboxylic acid, 1,4-bis(4-trimellitimidophenoxy)-2-tert-butylbenzene ( BTTB ), with various diamines by the direct polycondensation in N-methyl-2-pyrrolidinone (NMP) using triphenyl phosphite and pyridine as condensing agents. The new diimide–dicarboxylic acid BTTB containing an ether linkage and tert-butyl substituent was synthesized by the condensation reaction of 1,4-bis(4-aminophenoxy)-2-tert-butylbenzene with trimellitic anhydride. All the polymers were obtained in quantitative yields with inherent viscosities of 0.62–1.06 dL g⁻¹. The polymers were amorphous, and most of them were readily soluble in aprotic polar solvents such as NMP, N,N-dimethylacetamide (DMAc), and N,N-dimethylformamide (DMF), as well as in less polar solvents such as dimethyl sulfoxide (DMSO), m-cresol, pyridine, and γ-butyrolactone, and also even in tetrahydrofuran. The glass transition temperatures of the polymers were determined by DSC method, and they were in the range of 238–279°C. These polymers were stable up to 408–449°C in air and 451–483°C in nitrogen and lose 10% weight in the range of 479–525°C in air and 480–528°C in nitrogen atmosphere. The polymer films had a tensile strength range of 71–115 MPa, an elongation at break range of 4–14%, and a tensile modulus range of 2.3–3.1 GPa. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. A Polym. Chem. 36: 2301–2307, 1998     

Synthesis and characterization of norbornane-containing cardo polyamides

A new diamine, 2,2-bis[4-(4-aminophenoxy)phenyl]norbornane (BAPN), containing both ether and norbornane cardo groups, was synthesized in three steps started from norcamphor. A series of cardo polyamides were obtained by the direct polycondensation of BAPN and various aromatic dicarboxylic acids in N-methyl-2-pyrrolidinone (NMP) using triphenyl phosphite and pyridine as condensing agents. Polyamides had inherent viscosities in the range of 0.82–1.58 dL g⁻¹, and were readily soluble in polar aprotic solvents such as NMP, N,N-dimethylacetamide (DMAc) and N,N-dimethylformamide and dimethyl sulfoxide. These polymers were cast in DMAc solution into transparent, flexible, and tough films that were further characterized by X-ray and mechanical analysis. All the polymers were amorphous, and the polyamide films had a tensile strength range of 71–89 MPa, an elongation at break range of 5–9%, and a tensile modulus range of 2.0–2.3 GPa. Polyamides showed glass transition temperatures in the range of 256–296°C as measured by DSC and thermogravimetric analysis indicated no weight loss below 450°C in nitrogen and air atmosphere. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2791–2794, 1999     

Synthesis,characterization, and properties of hydroxyl‐terminated copolysiloxanes containing γ‐cyanopropyl groups

A series of random copolysiloxanes (PCDMS) containing various amount of γ‐cyanopropyl groups are prepared by a new method under mild conditions. Structures of the synthesized polymers are fully characterized by FTIR, ¹H NMR, ²⁹Si NMR, and GPC. Rheological properties of PCDMS are tested by cone and plate rheometer, and thermal properties by differential scanning calorimetry (DSC) and thermogravimetry analysis (TGA). Damping properties as well as fuel resistance of the cured PCDMS elastomers are also tested. The correlation between chemical structure, content of cyanopropyl group and properties are discussed. With the increasing amount of polar cyanopropyl group introduced, glass transition temperatures (T_g) of the synthesized PCDMS gradually increases from ?121 to ?65 °C, residual weight increases from 0 to 36% at 800°C, loss factor reaches as high as 1.74, mass increase under fuel immersion for 14 days can be as low as 3.6%. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1408–1421     

New technique of processing highly oriented poly(vinylidene fluoride) films exclusively in the β phase

Oriented β‐phase films were obtained by utilizing two different techniques: conventional uniaxial drawing at 80 °C of predominantly α‐phase films, and by drawing almost exclusively β‐phase films obtained by crystallization at 60 °C from dimethylformamide (DMF) solution with subsequent pressing. Wide angle X‐ray diffraction (WAXD) and pole figure plots showed that with the conventional drawing technique films oriented at a ratio (R) of 5 still contained about 20% of phase α, a crystallinity degree of 40% and β‐phase crystallographic c ‐axis orientation factor of 0.655. Drawing at 90 °C and with R = 4 of originally β‐phase films results in exclusively β‐phase films with crystallinity degree of 45% and orientation factor of 0.885. Crystalline phase, crystallinity degree, and crystallographic c‐axis orientation factor of both phases were also determined for α‐phase oriented films obtained by drawing α‐phase films at 140 °C. For films drawn at 140 °C the α to β phase transition drops to about 22%. Reduction in crystallinity degree with increasing R is more pronounced at draw temperature of 140 °C compared with 80 °C. Moreover, for both phases the c ‐axis orientation parallel to the draw direction is higher at draw temperature of 140 °C than at 80 °C. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2793–2801, 2007     

Drawing of ultrahigh molecular weight polyethylene fibers in the presence of supercritical carbon dioxide

The drawing behavior of ultrahigh molecular weight polyethylene fibers in supercritical carbon dioxide (scCO₂) is compared to that in air at different temperatures. The temperature substantially influences the drawing properties in air, whereas in scCO₂, a constant draw stress and tensile strength are observed. Differential scanning calorimetry shows an apparent development of a hexagonal phase along with a significant increase in the crystallinity of air‐drawn samples with increasing temperature. The existence of this phase is not confirmed by wide‐angle X‐ray scattering, which instead shows that air‐drawn samples crystallize in an internally constrained manner. In contrast, scCO₂ allows crystals to grow without constraints through a possible crystal–crystal transformation, increasing the processing temperature to 110 °C. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1375–1383, 2003     

Synthesis and characterization of novel polybenzimidazoles bearing pendant phenoxyamine groups

A novel aromatic diacid, 3, 5‐dicarboxyl‐4′‐amino diphenyl ether, containing pendant phenoxy amine group was synthesized. Homo‐ and co‐polybenzimidazoles containing different content of pendant phenoxyamine groups were synthesized by condensation of 3,3′‐diaminobenzidine with this acid and a mixture of this acid and isophthalic acid in different ratio in polyphosphoric acid. Copolybenzimidazoles with structural variations were also synthesized based on this acid and pyridine dicarboxylic acid, terephthalic acid, adipic acid, or sebacic acid. The polymers have good solubility in polar aprotic solvents and strong acids and they form tough flexible films by solution casting. The polymers were characterized by different instrumental techniques (FTIR, TGA, DSC, XRD, etc.) and for solvent solubility, mechanical properties, inherent viscosity, and proton conductivity. The inherent viscosities of the polymers vary in the range of 0.62–1.52 dL/g. They have high thermal stability up to 475–506 °C (IDT) in nitrogen, high glass transition temperatures (T_g) ranging from 313 to 435 °C and good tensile strength ranging from 58 to 125 MPa. Proton conductivity of homo polymer is 3.72 × 10^?3 S/cm at 25 °C and 2.45 × 10^?2 S/cm at 200 °C © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5776–5793, 2008     

Modifying an amorphous polymer to a fast crystallizing semi‐crystalline material by copolymerization with monodisperse amide segments

Segmented block copolymers of polysulphone with monodisperse amide segments were synthesized by a melt and a solution polymerization method. Both triblock and multiblock copolymers were prepared. The length of the difunctional polysulphone was varied from 2000 to 20,000 g/mol. The monodisperse amide segment was the tetra‐amide T6T6T based on terephthalic acid (T) and hexamethylene diamine (6) units. The main goal of this work was to study if the high T_g amorphous polysulphone could be modified to a high T_g semi‐crystalline PSU‐T6T6T copolymer. The copolymers were characterized by viscosity measurements, NMR, FTIR, MALDI‐TOF, DSC, and DMA. Depending on the amide concentration in the copolymers the T6T6T melting temperatures ranged between 220 and 270 °C and thus the crystallization window was small 50–100 °C. From the FTIR results, it was revealed that the crystallinity of the T6T6T segments in the copolymer could be very high, up to 92–97%. The T6T6T has crystallized out into nanoribbons with a high aspect ratio. These high T_g semi‐crystalline copolymers had a high dimensional and solvent resistance. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 63–73, 2010